Home

WISMO218 AT Commands User Manual

image

Contents

1. Connects the two calls and disconnects the subscriber from both calls ECT wavecon o 2009 Page 51 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business Proprietary value Swap operation retrieves the held call and holds the active call Not applicable for calls engaged in a multiparty operation CME ERROR returned Proprietary value Retrieves the specified held call x Not applicable for calls engaged in a multiparty operation CME ERROR returned Proprietary value Holds the specified active call x Not applicable for calls engaged in a multiparty operation CME ERROR returned Proprietary value Releases the specified call x whatever its state Proprietary value Aborts MO speech call x setup without releasing other calls Possible if OK result code is sent before call is connected allowed if PSCSSC mode enabled and COLP disabled 3 4 12 CTFR Call deflection Description Command Possible Response s Deflect a MT call CTFR lt number gt lt type gt lt subadd CME ERROR r gt lt satype gt lt err gt Test if command is CTFR supported Parameters lt number gt Description String type Integer type Type of address String type subaddress of format specified by lt satype gt wavecom o 20
2. WISM0O218 AT Command Manual Get current ACM CACM CACM lt acm gt CME ERROR lt err gt Test if command is CACM supported Parameters String type SIM PIN2 String type Accumulated call meter value similarly coded as lt ccm gt under CAOC 3 6 20 CANIM Accumulated call meter maximum Set ACMmax CAMM lt acmmax gt lt passwd gt CME ERROR lt err gt Get current CAMM CAMM lt acm gt ACMmax CME ERROR lt err gt Test if CAMM command is supported Parameters lt acmmax gt Description String type Accumulated call meter maximum value similarly coded as lt ccm gt under CAOC value zero disables ACMmax feature String type SIM PIN2 waveconm o 2009 Page 81 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual 3 6 21 CPUC Price per unit and currency table Set price per unit and CPUC lt currency gt CME ERROR lt err gt currency lt ppu gt lt passwd gt Get current currency CPUC CPUC lt currency gt lt ppu gt and price per unit CME ERROR lt err gt Test if command is CPUC supported Parameters lt currency gt Description String type Three character currency code e g GBP DEM character set as specified by command CSCS
3. wavecom o 2009 Page 6 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA _DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual 2 3GPP TS 27 005 commands 2 1 General configuration commands 2 1 1 CSMS Select Messages Service Select messages CSMS lt service gt CSMS lt mt gt lt mo gt lt bm gt service CMS ERROR lt err gt Get current service and CSMS CSMS settings lt service gt lt mt gt lt mo gt lt bm gt Get supported services CSMS CSMS list of Supported lt service gt s Parameters 0 3GPP TS 23 040 and 3GPP TS 23 041 Default value 1 3GPP TS 23 040 and 3GPP TS 23 041 the requirement of lt service gt setting 1 is mentioned under corresponding command descriptions lt mt gt lt mo gt Description lt bm gt o Type not supported 1 Type supported Default value Clarification lt service gt 1 shall be used only on dual OS platforms i e when TE is the only SMS client SMS are only routed to TA in this case lt service gt O shall be used by default wavecom o 2009 Page 7 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom pna Smart wireless Smart business
4. CME ERROR lt err gt Turn off greeting text String type A free text that shall be displayed Integer type Maximum number of character in lt text gt wavecom o 2009 Page 83 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Clarification This command only updates the greeting text in SIM card or EEPROM The mode is not stored in non volatile memory therefore Setting the mode to O even with a text as parameter is equivalent to setting the mode to 1 with an empty string the greeting text is lost The test command returns 1 if and only if the saved text is not empty in other words CSGT 1 then CSGT returns O 3 6 25 CSVM Set Voice Mail Number Description Command Possible Response s CSVM lt mode gt lt number gt lt type gt CME ERROR lt err gt CSVM list of supported mode gt s list of supported lt type gt s CME ERROR lt err gt Parameters Disable the voice mail number i e delete the voice mailbox number Enable the voice mail number lt number gt Description String type Character string lt 0O 9 gt Integer type Type of address 129 or 145 wavecom o 2009 Page 84 172 This document is the sole and exclusive property of WWAVECOM Not to be distrib
5. Parameters String type List of capabilities FCLASS CGSM 4 2 6 GMI Manufacturer identification Command Possible Response s Get manufacturer id GMI lt manufacturer gt CME ERROR lt err gt Test if command is GMI supported wavecom o 2009 Page 118 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom n Smart wireless Smart business WISMO218 AT Command Manual Parameters lt manufacturer gt ee e String type type Manufacturer id ssi id 4 2 7 GMM Model identification Get model id GMM lt model gt CME ERROR lt err gt Test if command is GMM supported Parameters String type type IModelid eee id 4 2 8 GMIR Revision identification Get model id GMR lt revision gt CME ERROR lt err gt Test if command is GMR supported Parameters lt revision gt Description 4 2 9 GSN Serial number identification Get model id GSN lt sn gt CME ERROR lt err gt Test if command is GSN supported wavecom o 2009 Page 119 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ashes Smart wireless Smart business WISM0O218 AT Command Manual Parameters
6. o 2009 Page 76 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Parameters String type Format is yy MM dd hh mm ss zz where characters indicate year two last digits month day hour minutes seconds and time zone indicates the difference expressed in quarters of an hour between the local time and GMT range 47 48 E g 6th of May 1994 22 10 00 GMT 2 hours equals to 94 05 06 22 10 00 08 3 6 14 CSIM Generic SIM access Send command to CSIM lt length gt lt command gt CSIM SIM lt length gt lt response gt CME ERROR lt err gt Test if command is CSIM supported Parameters Integer type Length of the characters that are sent to TE in lt command gt or lt response gt two times the actual length of the command or response lt command gt Description String type Command passed on by the MIT to the SIM in the format as described in GSM 51 01 Hexadecimal character format lt response gt Description String type Response to the command passed on by the SIM to the MT in the format as described in GSM 51 011 Hexadecimal character format Clarification SIM commands RUN GSM ALGORITHM TERMINAL PROFILE ENVELOPE FETCH and TERMINAL RESPONSE are not supported Whatever CSCS se
7. 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual lt class gt Description 2 data refers to all bearer services with lt mode gt 2 this may refer only to some bearer service if TA does not support values 16 32 64 and 128 Fax facsimile services 7 14 24 4 Default 4s CLI has been withheld by the originator 2 CLI is not available due to interworking problems or limitations of originating network 3 5 5 CUSD Unstructured supplementary service data USSD response from the CUSD lt m gt lt str gt lt dcs gt network or network initiated operation No further user action required network initiated USSD Notify or no further information needed after mobile initiated operation Further user action required network initiated USSD bel or s information needed after mobile initiated e a ore 2 JUSSD terminated USSD terminated by network 2 network Parameters sop aes 6 Network time out String type type USSD lUSSD string eee wavecom o 2009 Page 62 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218
8. AT Commands User Manual WISMO218 WlIreless Standard MOdem Reference WA DEV W218 UGD 003 Revision 001 Date April 24 2009 wovecom Smart wireless Smart business Wireless CPUs Operating Systems Integrated Development Environments Plug Ins Services wavecom Smart wireless Smart business WISMO218 AT Command Manual WISMO218 Wireless Standard MOQdem AT Command Manual Reference WA_DEV_W218_UGD_003 Revision 001 Date April 24 2009 wavecom o 2009 Page 1 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISMO218 AT Command Manual Trademarks S wavecom af inSIM YOU MAKE IT WE MAKE IT WIRELESS WAVECOM WISMO Open AT Wireless Microprocessor Wireless CPU and certain other trademarks and logos appearing on this document are filed or registered trademarks of Wavecom S A in France and or in other countries All other company and or product names mentioned may be filed or registered trademarks of their respective owners Copyright This manual is copyrighted by WAVECOM with all rights reserved No part of this manual may be reproduced modified or disclosed to third parties in any form without the prior written permission of WAVECOM No Warranty No Liability This document is provided
9. as is Wavecom makes no warranties of any kind either expressed or implied including any implied warranties of merchantability fitness for a particular purpose or noninfringement The recipient of the documentation shall endorse all risks arising from its use In no event shall Wavecom be liable for any incidental direct indirect consequential or punitive damages arising from the use or inadequacy of the documentation even if Wavecom has been advised of the possibility of such damages and to the extent permitted by law wavecom o 2009 Page 2 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_ 003 001 April 24 2009 wavecom Smart wireless Smart business WISMO218 AT Command Manual Revision History April 24 2009 a a a wavecom o 2009 Page 3 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA _DEV_W218_UGD_003 001 April 24 2009 wavecom pa Smart wireless Smart business WISMO218 AT Command Manual Table of Contents 1 AT Commands Description 22222222 2222 2 2 2 6 2 3GPP TS 27 005 commandS 2 2222222222 22222 7 2 1 General configuration COMMANGAS cccccece cence neces ee eee ene tense tneeeneeeneeeaes 7 2 2 Message configur
10. ceccee cece eee e eee eee eee enna enna eeeeeeneees 105 4 ITU T V25 ter Commands 2 cess eee e eee eee eee eee eee eee eee 107 4 1 Call Control deseme ean n A A ieee aided nat eed eaebe eden oes 107 4 2 General TA control COMMANAS ccee cece eee eee eee eee eee e teeta e eae 114 4 3 TA TE interface COMMANAS ccc cece eee eee eee eee eee e eee 120 4 4 Resul COG OS eroian aroro vee die inne Sh a edie ee OE vd edie ee ede ee 125 5 Hayes Commands 222 2 222 e eee e eee eee eee ee eee eee 127 5 1 Standard Hayes COMMANAS ccceccc eee eee cent eee eee eee e eee e ene e ene e teen enna eaes 127 5 2 Advanced Hayes COMmMANGCiS ccceee eee eect eee eee e eee e eee een eee 129 6 TIA IS 101 COMMANASS 2 oie esses cece eee ee eee eee eee 132 6 1 VTS DTMF and tone Qeneration cccc cece nee e neces eee eens teas enae eens enaeees 132 wavecom o 2009 Page 4 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_ 003 001 April 24 2009 wavecom Smart wireless Smart business 6 2 6 3 6 4 6 5 7 1 7 2 8 1 8 2 8 3 8 4 8 5 8 6 8 7 VYTD aiolg weoll cclilol gw re re rrr rer Tre rere rere rere 133 VGR Receive gain selection ccc cee c cece ene eee teas eee teas eens ena e eens enae eas 133 VGT Transmit gain selection ticvicccicicraccrartaactnareratteartaaetnasteacteantaa
11. ee eee CME ERROR lt err gt mode Description This command allows presentation of field strength notification Set command enable or disable the presentation of PSFS each time field strength increase or decrease of 5 dBm Field strength notification PSFS lt Field strength gt lt UMTS Field Strength gt wavecom o 2009 Page 169 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom pn Smart wireless Smart business WISMO218 AT Command Manual Parameters los Disable presentation of notification Enable presentation of notification jo eswrxtevelis less than 1098m SSCS lt UMTS field Description strength gt UMTS RSCPis less than 11608m Clarification The values defined are not the same as for CSQ command 8 7 4 PSCSSC Call successful control Set mode PSCSSC lt mode gt CME ERROR lt err gt Get current mode PSCSSC PSCSSC lt mode gt Description This command controls the emission of the result code for MO speech successful set up If Connected line identification presentation supplementary service is activated refer to COLP result code for ATD command will be sent to TE when call is connected to the called party successful call set up If Connected line identification presentation supplementary service
12. lt PDP_addr gt lt d_comp gt L lt h_comp gt III List current defined CGDCONT CGDCONT lt cid gt lt PDP_type gt PDP lt APN gt lt PDP_addr gt lt data_comp gt lt head_comp gt lt CR gt lt LF gt CGDCONT lt cid gt lt PDP_type gt lt APN gt lt PDP_addr gt lt data_comp gt lt head_comp gt wavecom o 2009 Page 91 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual Get supported values CGDCONT CGDCONT range of supported lt cid gt s lt PDP_type gt list of supported lt d_comp gt s list of supported lt h_comp gt s lt CR gt lt LF gt CGDCONT range of supported lt cid gt s lt PDP_type gt list of supported lt d_comp gt s list of supported lt h_comp gt s Parameters PDP Context Identifier 1 Definition stored in non volatile memory PDP Context Identifier 2 Definition stored in non volatile memory 1 2 3 PDP Context Identifier 3 Default lt cid gt Locked in non volatile memory and is always defined 4 11 ct ne PDP Context Identifier 4 11 IP Internet Protocol IETF STD 5 Point to Point Protocol IETF STD 51 String type Access Point Name If the value is null or omitted then the subscription value will be requested Stri
13. o 2009 Page 23 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISMO218 AT Command Manual SMS is automatically saved in SIM this is to not to lost an already acknowledged SMS for which CNMA has not been received in case of switch off If CNMA is received before timer expiration OK is returned else ERROR is returned TE knows that SMS has been stored in SIM Message waiting indication There are 3 possible cases to receive voice mail notification e TP DCS method STORE DISCARD message coding groups in DCS e TP UDH Special SMS indication IEl in UDH of the SM e CPHS method originating address decoding In all cases the ME manages messages notifications internally update of EF VMWI CPHS file acknowledgement In case of TP DCS method for message waiting indication group store message CMTI is sent For message waiting indication group discard message CMT URC is sent but no CNMA command is expected Voice mail waiting indication status are managed by PSVMWN command 2 5 3 CBM Received CBM indication Receive a CBM if text mode CMGF 1 CBM lt sn gt lt mid gt lt dcs gt lt page gt lt pages gt lt CR gt lt LF gt lt data gt if PDU mode CMGF 0 CBM lt length gt lt CR gt lt LF gt lt pdu gt Parameters Fo
14. 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Restriction If SAT call control modifies the SS an error is return to the TE 3 4 5 CPWD Change password Set new CPWD lt fac gt lt oldpwd gt lt newpwd gt CME ERROR lt err gt password CPWD list of supported lt fac gt lt pwdlength gt s CME ERROR lt err gt Parameters 2 sim PIN AO or OI or Refer Facility Lock CLCK for description OX or Al or IR or AB or SC lt oldpwd gt Description lt newpd gt String type lt oldpwd gt shall be the same as password specified for the facility from the MT user interface or with command Change Password CPWD and lt newpwd gt is the new password maximum length of password can be determined with lt pwdlength gt Integer type Maximum length of the password for the facility 3 4 6 CLIP Calling line identification presentation Control CLIP CLIP lt n gt notification Get status of CLI CLIP CLIP lt n gt lt m gt Get supported values CLIP CLIP list of supported lt n gt s wavecom o 2009 Page 46 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Parameters lt n gt Description o Disable CLIP notification
15. 8 1 1 CLS Service class Description Command Possible Response s Get the current mode CLS CLS list of currently available lt class gt s Parameters lt class gt IM O O default Data mode mode 1s Fax class 1 TIA 578 A mode Clarification This command has the same role and behaviour as FCLASS command It is needed for Microsoft agreement 8 2 Flow control command 8 2 1 amp R RTS CTS option Set RTS CTS option I CMEERROR lt err gt sd Parameters In sync mode CTS is always ON RTS transitions are ignored In async mode CTS will only drop if required by the flow control See Data stored by amp W for default value Clarification This command selects how the modem controls CTS CTS operation is modified if waveconm o 2009 Page 140 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual hardware flow control is selected see amp K command The parameter value if valid is written to S21 bit2 8 3 Manufacturer tests command 8 3 1 CPOF Power off Description This command allows switching off the mobile Note that OK result code will appear immediately if the command is accepted and power off will occur after that Unexpected random characters may also be iss
16. Example CFU interrogation for telephony service ATD 21 11 PSSSURC 33 11 0 255 129 0 1 2 1 OK Ss_code 33 gt SPS_SC_CFU BasicServicecode 11 gt SPS _ BS TELEPHONY SsStatus O gt SPS _ STATUS DEACTIVATED 8 3 3 PSSLEEP Power Management control PSSLEEP lt mngt gt CME ERROR lt err gt PSSLEEP PSSLEEP list of supported lt mngt gt s OK PSSLEEP PSSLEEP lt mngt gt OK Parameters O The module doesn t go in sleep mode as long as DTR is set to high level 1 The module decides by itself internal timing when it goes in sleep mode Clarification Action command set sleep mode for MIT If the command fails in an MT error CME ERROR lt err gt is returned Test command returns supported array index values In sleep mode need a A to wake up the system then the AT command can be input normally wavecom o 2009 Page 142 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual 8 4 SIM toolkit command and result codes 8 4 1 PSSTKI SIM Toolkit interface configuration Set mode PSSTKI lt mode gt CME ERROR lt err gt Get current mode PSSTKI PSSTKI lt mode gt CME ERROR lt err gt Get supported modes PSSTKI PSSTKI list of Supported lt mode gt
17. Upon an on to off transition of circuit 108 2 the DCE enters online command state and issues an OK result code the call remains connected Not supported 2 Upon an on to off transition of circuit 108 2 the DCE instructs the underlying DCE to perform an orderly cleardown of the call Clarification In case of Drop DTR if the signal remains in the off state more than two seconds it is considered as a PC disconnection and no OK is sent to the TE cable considered unplugged The behaviour of the command complies to the recommendation description only with DTR pulses pulse DTR signal stay in the off state unless 2 seconds 4 3 10 IPR Fixed TE rate Set TE rate TE rate IPR lt rate gt lt rate gt Get current rate l lt rate gt Get supported values IPR IPR list of supported auto detectable lt rate gt s list of supported fixed only lt rate gt s Parameters o Automatic rate detection S 1200 1200 bps 2400 bps 4800 480 bps 9600 9600 bps wavecom o 2009 Page 123 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom eee Smart wireless Smart business lt rate gt 4 3 11 ICF TE TA character framing Set TE TA character ICF lt format gt lt parity gt framing Get current value ICF lt format gt lt parity gt ICF
18. WISMO218 AT Command Manual 2 1 2 CPMS Preferred Messages Storage Descriptio Command Possible Response s CPMS lt mem1 gt CPMS lt mem2 gt lt mem3 gt lt used1 gt lt total1 gt lt used2 gt lt total2 gt lt used3 gt lt t otal3 gt CMS ERROR lt err gt CPMS lt mem1 gt lt used1 gt lt totall gt lt mem2 gt lt used2 gt lt total2 gt lt mems3 gt lt used3 gt lt total3 gt CMS ERROR lt err gt CPMS list of supported lt mem1 gt s list of supported lt mem2 gt s list of supported lt mem3 gt s Parameters lt mem x gt Description Only SM storage is supported BM ME MT TA SR memory locations are NOT supported lt used x gt lt total Description x gt Integer type Computed value 2 1 3 CMGF Messages Format Select message format CMGF lt mode gt Get current format___ CMGF Get supported formats CMGF CMGEF list of supported lt mode gt s pou mode waveconm o 2009 Page 8 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual omitted Use previous value 2 2 Message configuration commands 2 2 1 CSCA Service Center Address Update SMSC CSCA lt sca gt lt tosca gt address Get cu
19. o 2009 Page 130 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Clarification Execution command stores the active lt profile gt Two profiles are supported but they are equivalent Parameter stored by amp W Command Parameter name Displayed Non volatile memory filed by amp V C eo kvenai en heoo FLAGS wavecom o 2009 Page 131 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 6 TIA IS 101 commands 6 1 VTS DTMF and tone generation Generate tone VTS lt DTMF gt Duration is set by VTD Generate DTMF of VTS lt tone1 gt lt tone2 frequencies lt tone1 gt lt duration gt and lt tone2 gt lasting for a time lt duration gt in 10 ms multiples Generate tone VT lt DTMF gt Duration is set by lt duration gt lt duration gt Get supported values list of supported lt tone1 gt s list of supported lt tone2 gt s list of supported lt duration gt s Parameters Character type A single ASCII character in the set 0 9 A D lt tone1 gt Description
20. 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISMO218 AT Command Manual Verbose result Numeric result Description code command code V1 set command VO set OK Final Acknowledges execution of a command line CRING rs ees ee RING 2 Unsolicited Incoming call signal from network Parameters lt text gt Numeric value wavecom o 2009 Page 126 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_ 003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 5 Hayes commands 5 1 Standard Hayes commands 5 1 1 B Communication option Set communication B lt standard gt option Parameters 0 99 standard o Clarification This command is supported for compatibility purpose and has no effect on ME simple response OK 5 1 2 N Negotiate Handshake Parameters jog option o Clarification This command is supported for compatibility purpose and has no effect on ME simple response OK 5 1 3 S1 Ring Count Read ring count for last S1 lt num gt MIT call wavecom o 2009 Page 127 172 This document is the sole and exclusive property of WWAVECOM Not to be distrib
21. 2 5 1 CMTI Received SMS indication Receive a SM already stored CMTI lt mem gt lt index gt Parameters 1 255 Message location in SM memory lt mem gt Description sms fonly SM storage possible for SMS 2 5 2 CMT Received SMS indication if text mode CMGF 1 CMT lt oa gt lt alpha gt lt scts gt lt tooa gt lt fo gt lt pid gt lt dcs gt lt sca gt lt tosca gt lt length if PDU mode CMGF 0 CMT lt alpha gt lt length gt lt CR gt lt LF gt lt pdu gt Receive a SM Parameters For all other parameters refer to 27 005 83 1 Parameter Definitions Clarification When CSMS lt service gt is set to O all received SMS are automatically stored in SIM before CMT is sent to TE When CSMS lt service gt is set to 1 depending of it class SMS has to be acknowledged to network thanks to CNMA commands Depending of lt mode gt lt mt gt of CNMI or channel status available or reserved URC cannot or should not be sent to TE In these cases SMS can be automatically acknowledged or rejected without waiting CNMA command When a CMIT URC is sent to TE for a SMS that has NOT been acknowledged by TA a timer is started If timer expires 15sec before CNMA command is received SMS is rejected When a CMIT URC is sent to TE for a SMS that has already been acknowledged by TA a timer is started If timer expires 15sec before CNMA command is received wavecon
22. 2009 Page 89 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual 22 Not fount ps memoi SSS ps SS S ext string too long SSSSCSC S S S a o irven charactors mtoa sring O e diial string toolong O 27 invalid characters in dialing SSS a e OO a2 Network not alowed emergency calis oniy ao Network personalization PIN required amooo Network personalization PUK required a2 Network subset personalization PIN required 28 ____ Network subset personalization PUK required a4 Service provider personalization PIN required as berviee provider personalization PUK required se Corporate personalization PIN required a7 Corporate personalization PUK required C e peee for CCWA command only ea E This error code is also applicable to UIC wavecom o 2009 Page 90 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual GPRS related error 3 10 Commands for Packet domains 3 10 1 CGDCONT Define PDP Context Define a PDP CGDCONT lt cid gt lt PDP_type gt lt APN gt
23. CFUN list of supported lt fun gt s list of Supported lt rst gt s CME ERROR lt err gt Parameters Disable phone both transmit and receive RF circuits O default Do not reset the MT before setting it to lt fun gt power level Reset the MIT before setting it to lt fun gt power level Clarification AT CFUN 1 1 generates a blocking defense to reset the mobile OK result code will appear after reset has been completed AT CFUN 1 1 has no effect on radio on off it leaves it as the same state it was before reset AT CFUN 1 0 request a radio on and memorize in non volatile memory lt fun gt level AT CFUN 4 0 request a radio off and memorize in non volatile memory lt fun gt wavecom o 2009 Page 65 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual level At next switch on ME will be started with the lt fun gt level of the last CFUN i e radio on or off This allows TE to have control on radio on off 3 6 3 CPIN Enter PIN Send password to CPIN lt pin gt lt newpin gt CME ERROR lt err gt MT Check if a password CPIN CPIN lt code gt is expected CME ERROR lt err gt Test if command is CPIN supported Parameters READY MIT is not pending for any password SIM
24. Command Manual force the same state as 2 and 3 until another write command Value 23 is also permanent until another write command The values 5 to 8 have been developed for testing purposes Level volume are accessible with AT CLVL wavecon o 2009 Page 135 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA _DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual 7 TIA578A commands 7 1 General commands 7 1 1 FMI Manufacturer identification Get manufacturer ID FMI lt manufacturer gt CME ERROR lt err gt Test if command is FMI supported Parameters lt manufacturer gt Description String type Read manufacturer identification 7 1 2 FMM Model identification Get model ID FMM lt model gt CME ERROR lt err gt Test if command is FMM supported Parameters String type Read model identification 7 1 3 FMR Revision identification Get revision ID FMR lt revision gt CME ERROR lt err gt Test if command is FMR supported wavecon o 2009 Page 136 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Parameters
25. EFFDN under DFTelecom is selected If a UICC with an active USIM application is present the information in EFFDN under ADFUSIM is selected MC MT missed unanswered received calls list CPBW may not be applicable for this storage wavecom o 2009 Page 71 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual ON SIM or MT own numbers MSISDNs list reading of this storage may be available through CNUM also When storing information in the SIM UICC if a SIM card is present or if a UICC with an active GSM application is present the information in EFMSISDN under DFTelecom is selected If a UICC with an active USIM application is present the information in EFMSISDN under ADFUSIM is selected RC MIT received calls list CPBW may not be applicable for this storage SM default SIM UICC phonebook If a SIM card is present or if a UICC with an active GSM application is present the EFADN under DFTelecom is selected If a UICC with an active USIM application is present the global phonebook DFPHONEBOOK under DFTelecom is selected AP Selected application phonebook If a UICC with an active USIM application is present the application phonebook DFPHONEBOOK under ADFUSIM is selected Integer type Value indicating the number of us
26. Entrytocation S location 4 1 4 H Hang up Hang up a call H lt value gt CME ERROR lt err gt sd ERROR lt err gt wavecom o 2009 Page 109 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ae Smart wireless Smart business Disconnect ALL calls on THE channel the command is requested All active or waiting calls CS data calls GPRS call of the channel will be disconnected Disconnect all calls on ALL connected channels All active or waiting calls CSD calls GPRS call will be disconnected clean up of all calls of the MIE Disconnect all connected CS data call only on the channel the command is requested speech calls active or waiting or GPRS calls are not disconnected Disconnect all connected GPRS calls only on the channel the command is requested speech calls active or waiting or CS data calls are not disconnected Disconnect all CS calls either speech or data but does not disconnect waiting call either speech or data on the channel the command is requested Disconnect waiting call either soeech or data but does not disconnect other active calls either CS speech CS data or GPRS on the channel the command is requested rejection of incoming call Clarification Note Voice call disconnection is also dependant of CVHU settings In call modifica
27. ICF list of supported lt format gt s list of supported lt parity gt s Parameters BS data 1 stop 3 sbace Clarification This command is supported for compatibility purpose and has no effect on ME It provides information on hardware capabilities 4 3 12 IFC TE TA local flow control Set TE TA local IFC lt TA_by_TE gt lt TE_by_TA gt flow Get current value IFC IFC lt TA_by_TE gt lt TE_by_TA gt wavecom o 2009 Page 124 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ooo Smart wireless Smart business IFC list of supported lt TA_by_TE gt s list of supported lt TE_ by TA gt s Parameters No flow control Safeware flew caniel 2 Hardware flow control No flow control Software flow control Hardware flow control Clarification This command configures the flow control mode 4 4 Result codes Verbose result Numeric result Type Description code command code ise command VO set BUSY Busy signal detected CONNECT 1 Intermediate Connection has been established ERROR NO ANSWER a Finar__ Eonnection completion imout Intermediate As CONNECT but manufacturer specific lt text gt gives additional information e g connection data rate NO DIALTONE No dialtone detected waveconm o 2009 Page 125
28. L2P gt CONNECT iL lt cid gt ERROR Get supported values CGDATA CGDATA list of Supported lt L2P gt s Parameters PPPs Point to point protocol for a PDP such as IP PDP Context Identifier PDP Context Identifier Clarification If no parameters are provided i e CGDATA lt CR gt the last lt cid gt activated with CGACT or the default lt cid gt is used Only one lt cid gt in the command is supported i e CGDATA PPP lt cid gt lt CR gt This command is used for PDP tests on network emulators On real network functioning of CGACT and then CGDATA for data transfer is not guaranteed CGDATA implementation does not perform PS attach or PDP context activation The PDP identified by lt cid gt when provided in CGDATA must have been activated previously thanks to CGACT command CGDATA only switches channel to online data mode and open PPP server in a proprietary mode called FTA mode In this mode PPP only acts a relay For IP over PPP services ATD 98 or ATD 99 commands must be used when activating a PDP context PCO protocol configuration option has to be provided to network PCO can be provided to network only if a PPP negotiation LCP NCP wavecom o 2009 Page 99 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business
29. Outgoing International Calls except to Home Country BAIC Barr All Incoming Calls BIC Roam Barr Incoming Calls when Roaming outside the home country AaBs JAI Barring services wavecon o 2009 Page 44 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business SIM card or active application in the UICC GSM or USIM fixed dialling memory feature if PIN2 authentication has not been done during the current session PIN2 is required as lt passwd gt PN Network Personalization Correspond to NCK code PU Network sUbset Personalization Correspond to NSCK code Service Provider Personalization Correspond to SPCK code aco SA inComing barring services AG a outGoing barring services ounce SOS SC C String type Shall be the same as password specified for the facility from the MT user interface or with command Change Password CPWD 1 Voice telephony 2 data refers to all bearer services with lt mode gt 2 this may refer only to some bearer service if TA does not support values 16 32 64 and 128 Fax facsimile services a Ce 7 C e SSCS wavecom o 2009 Page 45 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24
30. PIN MIT is waiting SIM PIN to be given SIM PUK MIT is waiting SIM PUK to be given SIM PIN2 MIT is waiting SIM PIN2 to be given This lt code gt is returned only when the last executed command resulted in PIN2 authentication failure i e CME ERROR 17 If PIN2 is not entered right after the failure MT does not block its operation SIM PUK2 MT is waiting SIM PUK2 to be given This lt code gt is returned only when the last executed command resulted in PUK2 authentication failure i e CME ERROR 18 If PUK2 and new PIN2 are not entered right after the failure MT does not block its operation PH NET PIN MIT is waiting network personalization password to be given Correspond to NCK code PH NETSUB PIN MIT is waiting network subset personalization password to be given Correspond to NSCK code PH SP PIN MIT is waiting service provider personalization password to be given Correspond to SPCK code PH CORP PIN MIT is waiting corporate personalization password to be given Correspond to CCK code Clarification When the pin code is required the error result code is a CMS ERROR for the AT wavecom o 2009 Page 66 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual commands that belong to the 27 005 and a CME ERROR for all the o
31. Page 94 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart business WISM0O218 AT Command Manual Get current settings CGQREQ CGQOREQ lt cid gt lt precedence gt lt delay gt lt reliability gt lt peak gt lt mean gt lt CR gt lt LF gt CGQOREQ lt cid gt lt precedence gt lt delay gt lt reliability gt lt peak gt lt mean gt Get supported values CGOREQ CGQOREQ lt PDP_type gt list of supported lt precedence gt s list of supported lt delay gt s list of supported lt reliability gt s list of supported lt peak gt s list of supported lt mean gt s lt CR gt lt LF gt CGOREQ lt PDP_type gt list of supported lt precedence gt s list of supported lt delay gt s list of supported lt reliability gt s list of Supported lt peak gt s list of supported lt mean gt s Parameters 1 3 PDP Context Identifier Definition stored in non volatile memory refer to CGDCONT PDP Context Identifier lt precedence gt Description O default QOS precedence class subscribed value 4 3 Joos precedence class O default QOS delay class subscribed value QOS delay class subscribed o QOS reliability class subscribed value wavecom o 2009 Page 95 172 This document
32. SETUP CALL Send a APPI_STK_SETUP_CALL_ TERMINATED REQ TERMINATED COMMAND Send a APPILSTK_COMMAND RUT REJECTED Used to reject any URC that requires a response NOTIFICATION Send a APPI_STK_NOTIFICATION RSP SETUP CALL Send a APPI_STK_SETUP_CALL_RSP DISPLAY TEXT Send a APPI_STK_DISPLAY TEXT _RSP GET INKEY Send a APPI_STK_GET_INKEY RSP GET INPUT Send a APPI_STK_GET_INPUT_RSP PLAY TONE Send a APPI_STK_PLAY_TONE_RSP wavecom o 2009 Page 145 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual SELECT ITEM Send a APPI_STK_SELECT_ITEM_RSP SETUP MENU Send a APPI_STK_SETUP_MENU_RSP REMOVE MENU Send a APPI_STK_REMOVE_MENU_RSP SETUP IDLE Send a APPI_STK_SET_UP_IDLE_MODE_TEXT_RSP MODE TEXT Integer or string Number of parameters in URC depends of message type Refer to STK SwISD and source code Use case TE PC ME l lt PSSTK DISPLAY TEXT lt unsolicited result code received from SIM ToolKit PSSTK DISPLAY TEXT gt lt Answer to an unsolicited l result code l lt OK lt AT command result 8 5 CPHS proprietary commands 8 5 1 PSVMWN Voice Message Waiting Notification PSVMWN lt mode gt Get current mode PSVMWN PSVM
33. SMS are automatically stored in SIM before CMT or CMTI URC is sent to TE whatever lt mt gt value When CSMS lt service gt is set to 1 depending of it class SMS has to be acknowledged to network thanks to CNMA commands Depending of lt mode gt lt mt gt and channel status available or reserved URC can not or should not be sent to TE In these cases SMS can be automatically acknowledged or rejected without waiting CNMA command BM storage is not supported hence CBMII is not supported SR storage is not supported by platform hence CDSI is not supported CNMI non volatile memory storage _ Default value Non volatile memory field lt bfr gt o 1 bit loxoo sd v V CNMI ofr o _bfr e est a sent ame e o ooo f onmi moas feens foroo v CNMI Mode 2 3 2 CNMA New Message Acknowledgement to ME TA Acknowledge if text mode CMGF 1 CMS ERROR lt err gt indication CNMA if PDU mode CMGF 0 CNMA lt n gt lt length gt lt CR gt PDU is given lt ctrl Z ESC gt if PDU mode CMGF 0 CNMA list of Supported lt n gt s wavecom o 2009 Page 15 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Parameters lt n gt Description lo Cormmand operates similarly as defined
34. Smart business WISM0O218 AT Command Manual 2 4 2 CMISS Send Message from Storage Send a CMSS lt index gt lt da gt lt toda gt Jif text mode CMGF 1 and message from sending successful storage CMSS lt mr gt lt scst gt if PDU mode CMGF 0 and sending successful CMSS lt mr gt lt ackpdu gt if sending fails CMS ERROR lt err gt Parameters 1 255 Message location in SM memory In text mode lt scts gt is not supported in PDU mode lt ackpdu gt is not supported For all other parameters refer to 27 005 83 1 Parameter Definitions Clarification Since SMS STATUS REPORTs SMS COMMANDs and CBM are not stored in ME TA memory only lt index gt s of SMS SUBMITs and or SMS DELIVERs can be used in CMSS 2 4 3 CMGW Write Message to Memory Description Possible Response s if text mode CMGF 1 CMGW lt index gt CMGW lt oa da gt lt tooa toda gt lt stat gt lt CR gt CMS ERROR text is entered lt ctrl Z ESC gt lt err gt if PDU mode CMGF 0 CMGW lt length gt lt stat gt lt CR gt PDU is given lt ctrl Z ESC gt Test if command is supported wavecom o 2009 Page 21 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Parameters
35. String type Hexadecimal representation of a coding group as defined in CPHS recommendation 01 09 CO D5 String type Bitfield representation of each element of a service group ex 11000000 8 5 6 PSINEN Information number PSINFN lt index1 gt lt index PSINFN lt index1 gt lt number gt lt type gt lt text gt lt Net Id gt lt Prem Id gt lt Level gt lt CR gt lt LF gt PSINFN lt index2 gt lt number gt lt type gt lt text gt lt Net Id gt lt Prem Id gt lt Level gt lt CME ERROR lt err gt PSINFN list of Supported lt index gt s lt nlength gt lt tlength gt Description Set command returns phonebook entries in location number range lt index1 gt lt index2 gt from Information Number SIM file If lt index2 gt is left empty only location lt index1 gt is returned If all queried locations are empty but available no information text lines may be returned only an OK is returned If listing fails in a ME error CME ERROR lt err gt is returned wavecom o 2009 Page 151 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Read command has no effect returns OK Information number shall only be presented to TE if fie
36. WISM0O218 AT Command Manual negotiation has been initiated between mobile and TE before PDP activation refer to TS 27 060 89 1 This negotiation is possible only if AT channel is switched to online data mode before PDP context activation Hence the PDP identified with lt cid gt in CGDATA should not have been activated by CGACT gt not possible in the current implementation CGDATA does not behaves as ATD 9x when lt cid gt is not activated To go back in online command the escape sequence has to be sent on link in data mode CGDATA can also be used to switch again channel to online data mode after if PDP is still active Same behaviour has ATO command PDP test use case AT CGACT 1 1 PDP 1 is activated OK No PCO negotiation AT CGDATA CONNECT PPP server is opened in FTA mode channel is switched in online data mode No LCP NCP negotiation Data transfer eee Channel is back to online command mode OK ATH PPP server FTA mode is closed but PDP is NOT OK deactivated AT CGACT 0 1 PDP 1 is deactivated If ATH is not sent before OK deactivation CGACT returns ERROR 3 10 8 CGPADDR Show PDP address Get PDP addresses CGPADDR lt cid gt CGPADDR lt cid gt lt PDP_addr gt lt cid gt lt CR gt lt LF gt CGPADDR lt cid gt lt PDP_addr gt Level Get defined lt cid gt CGPADDR CGPADDR list of defined lt cid gt s Parameters PDP Context Identifier PDP C
37. as output user cannot select pull mode as no pull 8 6 11 WMPWM PWM and buzzer configuration Set PWM WMPWM lt output gt lt operati OK configuration on gt lt period gt lt dutycycle gt WMPWWM WMPWM lt output gt lt operation gt lt period gt lt dutycycle gt VWMPWM lt output gt lt operation gt lt period gt lt dutycycle gt ved OK WMPWM WMPWM list of supported lt output gt s list of supported lt operation gt s list of supported lt periods gt s list of supported lt dutycycle gt s OK This command allows setting PWM or buzzer configuration Description Parameters C ee OT odo SOS SC CSCSCS wavecon o 2009 Page 162 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Mo turn on SE on O 126 O PWM always low level when lt output gt is 1 126 PWM period as n 1 TSYSCLK 8 TSYSCLK 8 PWMO or PWM1 1 26MHz 8 307ns O 1024 freq SYSCLK period 2 64 when lt output gt is ex if period 203 then freq 26MHz 203 2 64 1KHz buzzer O 100 dutycycle percentage Note Buzzer does not have Always high level operation Default values of period and duty cycle for PWMO and PWM1 are 63 50 Default valuse o
38. be present if manual selection fails automatic mode lt mode gt 0O is entered O default a Oe format alphanumeric lt oper gt String type Refer to 27 007 Unknown SSS wavecom o 2009 Page 43 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual Current Clarification When Manual automatic operator selection is requested lt mode gt 4 COPS will return lt mode gt 0 or lt mode gt 1 depending which registration mode was successful lt mode gt 4 will not be returned If set command is aborted an abort of the registration on going is requested If test command is aborted get available PLMN procedure is aborted a partial list of PLMIN is returned 3 4 4 CLCK Facility lock CLCK lt fac gt lt mode gt lt passwd gt lt class gt when lt mode gt 2 and command successful CLCK lt status gt lt class1 gt lt CR gt lt LF gt CL lt status gt lt class2 gt CME ERROR lt err gt CLCK list of supported lt fac gt s CME ERROR lt err gt SIM lock SIM UICC card SIM UICC asks password in MT power up and when this lock command issued Correspond to PIN1 code BAOC Barr All Outgoing Calls BOIC Barr Outgoing International Calls X BOIC exHC Barr
39. for every command except STATUS wavecom o 2009 Page 78 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual lt P1 gt Description lt P2 gt lt P3 gt Integer type Parameters passed on by the MT to the SIM These parameters are mandatory for every command except GET RESPONSE and STATUS String type Information which shall be written to the SIM Hexadecimal character format lt sw1 gt Description lt sw2 gt Integer type Information from the SIM about the execution of the actual command These parameters are delivered to the TE in both cases on successful or failed execution of the command String type Response of a successful completion of the command previously issued STATUS and GET RESPONSE return data which gives information about the current elementary datafield After READ BINARY READ RECORD command the requested data will be returned lt response gt is not returned after a successful UPDATE BINARY UPDATE RECORD or SET DATA command Hexadecimal character format 3 6 16 CRSL Ringer sound level Set incoming call ringer CRSL lt level gt CME ERROR lt err gt sound leve Get current level CRSL CRSL lt level gt CME ERROR lt err gt Get supported values CRSL CRSL list of supported lt
40. info Set AD value PSADG lt Ade gt lt Meastime gt __ SSCS wavecom o 2009 Page 158 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Description This command will return AdcValue RequestedAdc MeasTime BurstPower Parameters jo Sae OSOSC S SCS je SSS deRMvoLTaceOOSOSC C S S a FROM 8 6 8 PSRIC RI behaviour Set Rimasker PSRIC lt Rimask gt lt Rishapa gt OOO O O O Get RI masker PSRIC ERROR Get supported RI PSRIC ERROR masker Description This command will set RI behaviour Parameters PCL es Oo dear wavecom o 2009 Page 159 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ate Smart wireless Smart business WISM0O218 AT Command Manual er SAL lO PULSER RI 8 6 9 WMGPIO GPIO access Set GPIO access WMGPIO lt IO gt lt cde gt if lt cde gt 2 WMIGPIO lt IO gt lt status gt OK else Get supported GPIO WMGPIO WMGPIO list of Supported access lt lO gt s list of supported lt cde gt s OK Description This command allows reading or writing a GPIO Parameter
41. level gt s CME ERROR lt err gt wavecom o 2009 Page 79 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ate Smart wireless Smart business WISM0O218 AT Command Manual Parameters lt level gt e lo 3 ievelrange eee range 3 6 17 CLVL Loudspeaker volume level Set sound Set sound speaker level level l CLVL lt level gt lt level gt CME ERROR lt err gt sd ERROR lt err gt Get current level CLVL CLVL lt level gt CME ERROR lt err gt Get supported values CLVL CLVL list of supported lt level gt s CME ERROR lt err gt Parameters lt level gt EE 4 10 levelrange eee range 3 6 18 CMUT Mute control IMute unmute call call l CMUT lt n gt lt n gt CME ERROR lt err gt sd ERROR lt err gt Get current mode CMUT CMUT lt n gt CME ERROR lt err gt Get supported values CMUT CMUT list of supported lt n gt s Parameters oid SCS 3 6 19 CACM Accumulated call meter Reset ACM CACM lt passwd gt CME ERROR lt err gt wavecon o 2009 Page 80 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business
42. lt dcss gt are not accepted String type all different possible combinations of CBM message identifiers refer lt mid gt in 27 005 String type all different possible combinations of CBM data coding schemes refer lt dcs gt in 27 005 Default value no DCS accepted Clarification All the lt dcss gt values can be accepted or up to 5 different lt dcss gt values can be accepted Ranges are not supported for lt mids gt and lt dcss gt i e notation 0 1 5 320 478 922 is not allowed for lt mids gt and notation 0 3 5 is not allowed for lt dcss gt Up to SPB _ MSG ID LIST SIZE 15 different lt mids gt values can be accepted AT CSCB 1 means all lt dcss gt are accepted but this command has no effect on the list of the lt mids gt accepted To modify those lists use before the AT CSCB 0O command to select no mid and no dcs and after this operation add some dcs or mid to the current lists AT CSCB 0 lt mids gt add the lt mids gt values in the lt mids gt current list handle by the mobile AT CSCB 0O lt dcss gt add the lt dcss gt values in the lt dcss gt current list handle by the mobile lf AT CSCB 0O lt value gt is received while the list of lt mids gt is full OK is returned and new value is not added wavecom o 2009 Page 10 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W21
43. lt revision gt Description String type Read revision identification 7 2 Capabilities identification and control 7 2 1 FCLASS Model identification FCLASS ee FCLASS TOAS Sees Get supported value FCLASS FCLASS list of supported lt class gt s Parameters lt class gt Description oO atamode o Fax class 1 TIA 578 A mode 7 2 2 FTH HDLC transmit Get supported modes FTH list of supported lt mode gt s Parameters Clarification Set command is sent to ME only when link is online data mode Hence set command is not implemented in AT command parser but in RLP FAX module wavecom o 2009 Page 137 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ate Smart wireless Smart business WISM0O218 AT Command Manual 7 2 3 FRH HDLC receive Description Command Possible Response s FRH lt mode gt ae Get supported modes FRH list of supported lt mode gt s Parameters Is Refer to TIA 578 A eee to TIA 578 A Clarification Set command is sent to ME only when link is online data mode Hence set command is not implemented in AT command parser but in RLP FAX module 7 2 4 FTM Facsimile transmit Set mode mode FTM FTM lt mode gt a E Get supported modes FTM list of supported lt mode gt s Parameters Intege
44. lt tone2 gt Use of tone 1 et 2 does not operate in GSM Manufacturer specific tone los Manufacturer Manufacturer specific duration ssssSsiSY duration Clarification This commands only works for speech calls in active state wavecom o 2009 Page 132 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a ates Smart wireless Smart business WISM0O218 AT Command Manual 6 2 VTD Tone duration Set tone duration tone duration l4VTD lt n gt sd lt n gt Get supported values list of Supported lt n gt s Parameters eee los Manufacturer Manufacturer specific duration sss sSsiSY duration 6 3 VGR Receive gain selection ISet receive gain receive gain l4VGR lt n gt sd lt n gt Get supported receive a of supported lt n gt s gain Parameters Description gain in dBm 255 63 5 254 63 129 0 5 128 0 127 0 5 2 63 1 63 5 O AUTO i e adjusted values inside the module 6 4 VGT Transmit gain selection wavecon o 2009 Page 133 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Get supported transmit in a of supported lt
45. n gt s gain Parameters Description gain in dBm 255 63 5 254 63 129 0 5 128 0 127 0 5 263 1 63 5 O AUTO i e adjusted values inside the module 6 5 VIP Initialize voice parameter Get supported voice VIP list of supported lt n gt s parameters Parameters Description Mode O Handset 7 levels of volume main audio interface 1 Handsfree 5 levels of volume main audio interface 2 Headset 5 levels of volume secondary audio interface 3 Car kit 5 levels of volume secondary audio interface 4 Car kit 5 levels of volume secondary audio interface 5 Internal Loop 1 test mode 6 Internal Loop 2 test mode 7 Internal Loop 3 test mode 8 Leave test mode test mode 21 Identical to 2 see note below 22 Identical to 3 See note below 23 Digital Audio Interface It is possible to re direct the audio paths O to 4 as well as the audio parameters filters gain through the provided Audio tool The mention to the main and secondary audio interfaces Speaker and Micro are linked to the default audio parameters and defined in HW The values 1 to 4 are automatically reset after a call return to O Values 21 and 22 waveconm o 2009 Page 134 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISMO218 AT
46. related URC to be sent on the channel CBM ME status related URC to be sent on the channel CIEV PSCP PSNWID PSUTTZ Network registration related URC to be sent on the channel CREG CGREG PSNTRG 1 2 16 2 SS related URC to be sent on the channel CUSD 64 Initialisation related URC to be sent on the channel PSREADY 128 Debug related URC to be sent on the channel PSDBG 256 SIM toolkit related URC to be sent on the channel PSSTK Clarification To enable the display of URC SMS 2 and CALL 1 and to forbid the display of the 4 3 wavecon o 2009 Page 156 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual others on a channel choose 2 and 1 parameter i e send AT PSCHRU 3 OK 8 6 5 PSTAT tool detection enable Trig restart with tool PSTAT lt param gt OK detection PSTAT ERROR Get supported formats PSTAT ERROR Parameters lt param gt Description Integer type type Useless Useless parameter ssssisi isSOSOSSSSSSCSCizdY Clarification The set command enables tool presence detection by embedded and provokes an intended watchdog reset When restarting after WD the init driver sends I 0x49 on UART to enquire for a tool Further reboots intended
47. s Description This command is to configure SIM toolkit by AT command Parameters STK by AT command is deactivated only ME s MMI will receive SIM toolkit notifications 1 STK by AT command is activated SIM toolkit notification will first be sent to AT parser If an AT channel is connected PSSTK URC will be sent PSSTK AT command has to be used to respond If no AT channel is connected ME s MMI will receive the notification 8 4 2 PSSTK SIM Toolkit control PSSTK command is defined to support SIM toolkit by AT commands Only part of SIM toolkit commands that interact with user or MMI can be controlled All other SIM toolkit mechanism such as terminal profile SMS or CBM data download call control or MO SMS control by SIM event download and all command that does not require interaction with the user or screen are internally managed by the ME This command is implemented in ATCUST module and can be updated modified Notification from SIM to user PSSTK unsolicited result code Notification from SIM to User PSSTK lt notification type gt lt parameter1 gt lt parameterN gt wavecom o 2009 Page 143 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom n Smart wireless Smart business WISMO218 AT Command Manual Parameters lt notification Descript
48. the SIM card or in the active application in the UICC GSM or USIM Clarification This warning will be triggered shortly before the ACM Accumulated Call Meter maximum value is reached an unsolicited result code CCWV will be sent if enabled by CCWE command The warning is issued approximately when 30 seconds call time remains It is also issued when starting a call if less than 30 seconds call time remains 3 7 2 CIEV Indicator event report Event report CIEV lt ind gt lt value gt Parameters lt value gt Description Range of value for lt ind gt O Range of value for lt ind gt 1 wavecom o 2009 Page 88 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ate Smart wireless Smart business WISM0O218 AT Command Manual 3 8 Mobile Termination error control 3 8 1 CIMEE Report Mobile Equipment error Seterormode remessa OOO O OSSO y yO Get supported values CMEE CMEE list of supported lt n gt s Parameters ooo Disable CME ERROR lt err gt result code and use ERROR instead Enable CME ERROR lt err gt result code and use numeric lt err gt Enable CME ERROR lt err gt result code and use verbose lt err gt values 3 9 Mobile Termination error result code 3 9 1 CME ERROR General error a faire Wa vVvecon o
49. 03 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual oe rr O O default Disable Disable presentation of CSSU S of CSSU ie Enable presentation of CSSU 3 4 16 CLCC List current calls CLCC lt id1 gt lt dir gt lt stat gt lt mode gt lt mpty gt lt nu mber gt lt type gt lt alpha gt lt CR gt lt LF gt CLCC lt id2 gt lt dir gt lt stat gt lt mode gt lt mpty gt lt number gt lt type gt lt alpha gt CME ERROR lt err gt Parameters 1 7 Call identification number This number can be used in CHLD command operations o Mobile originated MO call Mobile terminated MT call lo itiV E 2 doiaing Oca SSCS Bering WO eal OO oo OO 6 Waiting ar cay SSCS wavecom o 2009 Page 55 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual Voice Fax los Ca is not one of multiparty conference call parties Ho JCal is one of multiparty conference call parties lt number gt eoe I String type type Phone number number Integer type type Type of address sssi sSSSSSSSCi CSSCid of address String type Alphanumeric representation of lt number gt corresponding to the entry found in pho
50. 09 Page 52 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual Integer type Type of subaddress 3 4 13 CUSD Unstructured supplementary service data Control USSD CUSD lt n gt lt str gt lt dcs gt CME ERROR lt err gt iat comentimode CSD n Get supported CUSD CUSD list of supported lt n gt s values Parameters lt n gt Description loss Disable the result code presentation to the TE Enable the result code presentation to the TE 2s Cancel session not applicable to read command response String type USSD string Integer type Cell Broadcast Data Coding Scheme Default value O Restriction If SAT call control modifies the USSD an error is return to the TE Clarification When TE sends an USSD to the network the OK result code is sent before the response of the network When network answers the response will be sent as an URC as if it was a network initiated operation in case of error CUSD 4 will be sent This allows the link not to be blocked for a long time the network can take a long time to answer a USSD request initiated by the TE The USSD session can be aborted using command at cusd 2 wavecom o 2009 Page 53 172 This document is the sole and exclusive propert
51. 1 255 Message location in SM memory For all other parameters refer to 27 005 83 1 Parameter Definitions Clarification Text length is limited to PDU max length 164 2 4 4 CMGD Delete Message Delete a message _ CMGD lt index gt lt delflag gt CMS ERROR lt err gt Get supported 7 CMGD list of supported values lt index gt s list of supported lt delflag gt s Parameters Delete the message specified in lt index gt aad value Delete all read messages from preferred message storage leaving unread messages and stored mobile originated messages whether sent or not untouched Delete all read messages from preferred message storage and sent mobile originated messages leaving unread messages and unsent mobile originated messages untouched Delete all read messages from preferred message storage sent and unsent mobile originated messages leaving unread messages untouched 4 Delete all messages from preferred message storage including unread messages 1 255 Message location in SM memory For all other parameters refer to 27 005 83 1 Parameter Definitions wavecom o 2009 Page 22 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual 2 5 SMS and CBM unsolicited result codes
52. 18_UGD_003 001 April 24 2009 wevecom a Smart wireless Smart business Buffer unsolicited result codes in the MT if MT result code buffer is full the oldest ones is discarded Discard unsolicited result codes when MT TE link is reserved e g in on line data mode otherwise forward them directly to the TE Buffer unsolicited result codes in the MT when MT TE link is reserved e g in on line data mode and flush them to the TE when MT TE link becomes available otherwise forward them directly to the TE MT buffer of Unsolicited result codes defined within this command is cleared when lt mode gt 1 or 2 is entered MT buffer of Unsolicited result codes defined within this command is flushed to the TE when lt mode gt 1 or 2 is entered 3 11 1 CGREG registration status Registration change CGREG lt stat gt lt lac gt lt ci gt Parameters Not registered MIT is not currently searching an operator to register to The GPRS service is disabled the UE is allowed to attach for GPRS if requested by the user ei Registered home network Not registered but MT is currently trying to attach or searching an operator to register to The GPRS service is enabled but an allowable PLMN is currently not available The UE will start a GPRS attach as soon as an allowable PLMN is available waveconm o 2009 Page 105 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or
53. 2 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual CRLP CRLP lt iws gt lt mws gt lt 1T1 gt lt N2 gt lt ver1 gt lt T4 gt lt CR gt lt LF gt CRLP lt iws gt lt mws gt lt T1 gt lt N2 gt lt ver2 gt lt T4 gt CRLP list of supported lt iws gt s list of supported lt mws gt s list of supported lt T1 gt s list of supported lt N2 gt s lt ver1 gt L list of supported lt T4 gt s lt CR gt lt LF gt CRLP list of supported lt iws gt s list of supported lt mws gt s list of supported lt T1 gt s list of supported lt N2 gt s lt ver1 gt list of supported lt T4 gt s zal Parameters lt iws gt Description IWF to MS window size lo 61 MS to IWF window size o to IWF window size 44 255 Acknowledgement timer T4 ssi timer T1 1 255 JRetra nsmission attem Retransmission attempts N2 s N2 oii version OS 7 Re sequencing IRe sequencing period T4 in integer format sd T4 in integer format wavecom o 2009 Page 35 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart bus
54. 3 001 April 24 2009 wavecom Smart wireless Smart business WISMO218 AT Command Manual Is00 s lt tssd non error S error wavecom o 2009 Page 26 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA _DEV_W218_UGD_003 001 April 24 2009 wavecom ao ates Smart wireless Smart business WISM0O218 AT Command Manual 3 3GPP TS 27 007 commands 3 1 General commands 3 1 1 CGMII Request Manufacturer identification Read manufacturer Id CGMI lt manufacturer gt CME ERROR lt err gt Test if command is CGMI supported Parameters lt manufacturer gt Description String type Manufacturer identification 3 1 2 CGNIM Request Model Identification Read model CGMM lt model gt CME ERROR lt err gt Test if command is CGMM supported Parameters String type Model identification 3 1 3 CGMR Request Revision Identification Read revision CGMR lt revision gt CME ERROR lt err gt Test if command is CGMR supported wavecon o 2009 Page 27 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ao ates Smart wireless Smart business WISM0O218 AT Command Manual Parameters lt revision gt oO String type type Revi
55. 8_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 2 2 3 CSMIP Set Text Mode Parameters Select SM CSMP lt fo gt lt vp gt l lt pid gt lt dcs gt parameters Get current CSMP CSMP values lt fo gt lt vp gt lt pid gt lt dcs gt Parameters lt fo gt lt vp gt Description lt pid gt lt dcs gt Integer type Refer to 27 005 for description Clarification The enhanced validity period format EVPF see 23 040 is not supported lt fo gt is only for SMS DELIVER SMS SUBMIT or SMS STATUS REPORT See data stored by CSAS for default values 2 2 4 CSDH Show Text Mode Parameters Select header CSDH lt show gt presentation Get current status__ CSDH ee lt show gt Get supported values CSDH CSDH list of supported lt show gt s Parameters o Do not show header values o not show header values a Show the values in result codes wavecom o 2009 Page 11 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual 2 2 5 CSAS Save Settings Save SM service CSAS lt profile gt CMS ERROR lt err gt settings Get the list of available CSAS CSAS list of supported profiles lt profile gt s Parame
56. ALL command received MO call ALERT at distant Call initiated by SAT SET UP CALL command received MO call CONNECT with distant Call initiated by SAT SET UP CALL command received Note This command uses information available at APPI interface application iff AT parser does not interface directly with protocol stack so it does not have immediate access to L3 messages this means that lt state gt does not match L3 messages exactly as they are defined in 24 008 recommendation Call in ACTIVE state 1 Call in HOLD state applicable only for speech calls either MO or MT Call in MULTIPARTY ACTIVE state applicable only for speech calls either MO or MT Call in MULTIPARTY HOLD state applicable only for speech calls either MO or MT wavecom o 2009 Page 165 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom SEOS Smart wireless Smart business WISMO218 AT Command Manual String type Phone number same as in CLIP Integer type Type of address same as in CLIP 2 Line 2 auxiliary line Integer type Refer SwISD UPV lt Cause gt Description Refer SwISD UPV String type Hexadecimal representation format of bearer capability for data calls only i wavecom o 2009 Page 166 172 This document is the sole and exclusive property of WWAVECOM N
57. AT Command Manual Integer type Cell Broadcast Data Coding Scheme Default value O Clarification Refer to CUSD command description 3 5 6 CCCM Current Call Meter ICCM value si value CCCM lt cem gt ssid lt ccm gt Parameters lt ccm gt Description String type Three bytes of the current call meter value in hexadecimal format e g 00001E indicates decimal value 30 value is in home units and bytes are similarly coded as ACMmax value in the SIM card or in the active application in the UICC GSM or USIM Clarification This unsolicited result code is sent whenever the CCM value changes but not more than once every 10s This URC is activated when CAOC is in mode 2 3 5 7 CSSI Supplementary service notifications SS notification for MO call CSSI lt code1 gt Parameters lo Unconditional call Unconditional call forwarding is active ssid is active Some of the conditional call forwardings are active 2 feenresboontowarsa incoming cals are barred SSCS wavecom o 2009 Page 63 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart business WISM0O218 AT Command Manual 7 JCLR suppression rejected l3 Call has been deflected 3 5 8 CSSU Supplementary service notifications CSSU lt code2 gt Parameters Call on
58. CGREG lt n gt lt stat gt lt lac gt lt ci gt information CME ERROR lt err gt wavecom o 2009 Page 101 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual Get Get supported values values CGREG sd CGREG sd CGREG list of CGREG list of supported lt n gt s lt n gt s Parameters los Disable network registration unsolicited result code 1 Enable network registration unsolicited result code CGREG lt stat gt 2 Enable network registration and location information unsolicited result code CGREG lt stat gt lt lac gt lt ci gt Not registered MIT is not currently searching an operator to register to The GPRS service is disabled the UE is allowed to attach for GPRS if requested by the user 1 Registered home network 2 Not registered but MT is currently trying to attach or searching an operator to register to The GPRS service is enabled but an allowable PLMN is currently not available The UE will start a GPRS attach as soon as an allowable PLMN is available Registration denied The GPRS service is disabled the UE is not allowed to attach for GPRS if requested by the user Registered roaming lt lac gt Description String type Two byte location area code in hexadecima
59. Enable CLIP notification lt m gt Description los cP not provisioned 2 Unknown e g no network etc 3 4 7 CLIR Calling line identification restriction Get status of CLIR CLIR CLIR lt n gt lt m gt Get supported values CLIR CLIR list of supported lt n gt s Parameters Presentation indicator is used according to the subscription of the CLIR service lt m gt Description oti not provisioned S Wa vecon o 2009 Page 47 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom E Smart wireless Smart business WISMO218 AT Command Manual 3 4 8 COLP Connected line identification presentation Control COLP COLP lt n gt notification Get status of COLP COLP a lt n gt lt m gt Get supported values COLP COLP list of supported lt n gt s Parameters o Ss Disable COLP notification Enable COLP notification o COLP not provisioned 1 COLP provisioned 2 Unknown e g no network etc 3 4 9 CCFC Call forwarding number and conditions Description Command CCFC lt reason gt lt mode gt lt number gt lt type gt lt class gt lt subaddr gt lt satype gt lt Parameters lt reason gt Description Unconditional No reply Not reachable wavecom o 2009 Page 48 172 This document is the sole
60. F gt lt data gt if PDU mode CMGF 0 and command successful CMGR lt stat gt lt alpha gt lt length gt lt CR gt lt LF gt lt pdu gt otherwise CMS ERROR lt err gt Parameters 1 255 Message location in SM memory wavecom o 2009 Page 18 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual Received unread message i e new message Received read message REC READ Stored unsent message STO UNSENT All messages For all other parameters refer to 27 005 3 1 Parameter Definitions Other parameters are extracted from memory storage Clarification Only SMS SUBMIT and or SMS DELIVER can be read SMS COMMAND are not supported CBM are not stored in ME TA memory CBM are not saved in SIM 2 4 Message sending and writing commands 2 4 1 CMGS Send Message Send a message if text mode CMGF 1 if text mode CMGF 1 and CMGS lt da gt lt toda gt lt CR gt sending successful text is entered lt ctrl Z ESC gt CMGS lt mr gt lt scts gt if PDU mode CMGF 0 if PDU mode CMGF 0 and CMGS lt length gt lt CR gt PDU sending successful is given lt ctrl Z ESC gt CMGS lt mr gt lt ackpdu gt if sending fails CMS ERROR lt err gt Test if command CMGS is Sup
61. IND Require use of PSSTK set command to respond to SIM SETUP IDLE Sent on reception of APPI_STK_SET_UP_IDLE MODE_TEXT_IND MODE TEXT Require use of PSSTK set command to respond to SIM wavecom o 2009 Page 144 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ate Smart wireless Smart business WISM0O218 AT Command Manual Integer or string Number of parameters in URC depends of message type Refer to STK SwISD and source code Response from user to SIM PSSTK command Respond to SIM PSSTK lt reponse type gt CME ERROR lt err gt lt parameter1 gt lt parameterN gt Get supported PSSTK PSSTKI list of supported response type lt response type gt s Parameters A string that represents the type of response to be sent to SIM terminal response or envelope Some response correspond to answer to PSSTK URC MENU Send a APPI_STK_MENU_SELECTION_REQ SELECTION On reception of APPI_STK_MENU_SELECTION_CNF OK is sent GET ITEM LIST Call macro MC_STK _FIRST_ITEM and MC_STK NEXT_ITEM to get the information of the last received SET UP MENU or SELECT ITEM command ALL CALLS Send a APPI_LSTK_ALL_DISCONNECTED_REQ o USER ACTIVITY ACTIVITY Send a APPI _STK_USER_ACTIVITY IND si a APPI_STK_USER_ACTIVITY_IND IDLE SCREEN Send a APPI_STK_IDLE SCREEN AVAILABLE IND AVAILABLE
62. P Context Identifier Clarification This command is used to tests PDPs with network simulators Successful activation of PDP on real network is not guaranteed Refer to CGDATA clarification for more information 3 10 6 CGCMOD PDP Context Modify Request PDP CGCMOD lt cid gt lt cid gt OK context modification Get active PDPs CGCMOD CGCMOD list of lt cid gt s associated with active contexts Parameters 441s PDP IPDP Context Identifier ssi lt isSSCSsisizdY Identifier wavecom o 2009 Page 98 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Clarification Recommendation specifies that after the command has completed the MT returns to online data state but OK result code is expected this seems inconsistent From Wavecom point of view CGCMOD behaviour is more similar to CGACT command hence the implementation choice is not to switch link to online data mode after PDP context modification TE will have to send escape sequence to switch channel to online command if CGCMOD cannot be performed from another AT channel TE will have to use O command if required to switch channel to online data mode 3 10 7 CGDATA Enter data state Enter data state CGDATA lt
63. R lt err gt from lt semicolon gt phonebook memory location Direct dialling D gt lt n gt lt clir gt lt cug gt lt semicolon gt CME ERROR lt err gt from phonebook entry location Parameters Dialling digits Dialling digits O123456789 abcdABCD TPtp Wwe Note T P D are ignored wavecom o 2009 Page 107 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom n Smart wireless Smart business WISMO218 AT Command Manual lt semicolon gt Description Character Semicolon character shall be added when voice call is originated String type should equal to an alphanumeric field in at least one phonebook entry in the searched memories used character set should be the one selected with CSCS Override the CLIR supplementary service subscription default value for this call Invocation restrict CLI presentation Override the CLIR supplementary service subscription default value for this call Suppression allow CLI presentation G Control the CUG supplementary service information for this call CUG Not supported Control the CUG supplementary service information for this call CUG Not supported tsm Only SM storage possible for SMS Integer type Memory location should be in the range of locations available in the memory used Restri
64. String type type Price per unit dot is used as a decimal separator e g 2 66 String type SIM PIN2 3 6 22 CCWE Call Meter maximum event Set call meter mode CCWE lt mode gt CME ERROR lt err gt max event Get current mode CCWE CCWE lt mode gt CME ERROR lt err gt Get supported modes CCWE CCWE list of supported lt mode gt s CME ERROR lt err gt Parameters co Disable the call meter warning event CCWV Enable the call meter warning event CCWV wavecom o 2009 Page 82 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual 3 6 23 CLAN Set Language Set language CLAN lt code gt CME ERROR lt err gt Get current mode CLAN CLAN lt code gt CME ERROR lt err gt Get supported modes CLAN CLAN list of supported lt code gt s CME ERROR lt err gt Parameters String type Language coded in ISO 639 format AUTO and non volatile memory supported 2 letters For example en for English 3 6 24 CSGT Set Greeting Text Set greeting text CSGT lt mode gt l lt text gt CME ERROR lt err gt Get current CSGT CSGT lt text gt lt mode gt values CME ERROR lt err gt Get supported CSGT list of supported lt mode gt s lt Itext gt
65. WN lt mode gt CME ERROR lt err gt Get supported modes PSVMWN PSVMWN list of Supported mode Description Set command enables disables the presentation of notification result code from ME to TE When lt mode gt 1 a Voice Message Waiting Indication PSVMW I is sent to TE when notification is received special SMS from network or at switch on wavecom o 2009 Page 146 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Voice Message Waiting PSVMWI lt line Id gt lt status gt Indication lt index gt lt NbMsgWaiting gt Parameters ce Disable presentation of notification Enable presentation of notification Line 2 Auxiliary line Fax o No message waiting Ho at least one message is waiting 0 255 Record index in EF SMS if the received MWI message has been stored in SIM if DCS indicates STORE MWI SMS 0 255 Number of message waiting on lt line id gt 8 5 2 PSALS Alternate Line Service Select line for MO PSALS lt Lineld gt speech call Get current line PSALS PSALS lt lineld gt CME ERROR lt err gt wavecom o 2009 Page 147 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior
66. and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom _ a Smart wireless Smart business WISM0O218 AT Command Manual lt reason gt Description e call forwarding 5 JA conditional call forwarding C SSCS String type Phone number of forwarding address in format specified by lt type gt Integer type Type of address String type subaddress of format specified by lt satype gt Integer type Type of subaddress lt class gt Description Voice telephony 2 data refers to all bearer services with lt mode gt 2 this may refer only to some bearer service if TA does not support values 16 32 64 and 128 Fax facsimile services wavecom o 2009 Page 49 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom p Smart wireless Smart business WISMO218 AT Command Manual When no reply is enabled or queried this gives the time in seconds to wait before call is forwarded Default value 20 o o Notatie S active ooo he S Restriction If SAT call control modifies the SS an error is return to the TE 3 4 10 CCWA Call waiting Control call CCWA lt n gt lt mode gt lt class gt when lt mode gt 2 and command waiting successful CCWA lt stat
67. ation COMMANAS cc cece cece nee e ee eee tenes ena e teas teas teas enaeeas 9 2 3 Message receiving and reading COMMandS ssssssssssessrrrnrrrrrnrrrrrrern 13 2 4 Message sending and writing CoOmMmmMmandS s sssssssssrssserrnrrrererrnnrreren 19 2 5 SMS and CBM unsolicited result COdES cccecee eee ee eee eee teat eee eaenaes 23 2 6 CMS ERROR Message Service Failure Result Code ccccce cence ees 25 3 3GPP TS 27 007 Commanhs ccce eee eee eee e eee eee eee eee eee 27 3 1 General ComMAaNS si avesis ids vats sade ety sans ve ey edkvece EENE segs vee pede veered es 27 3 2 Callicontrol Command tesccssieusieeesdcdiescteksseees bedseda teaser a aE 31 3 3 Call control result COdG cece eee ee ene ninaa tet anina wa 39 3 4 Network service related COMMANAS ccceeeeeee eee eee eee teat teat teat enee ties 40 3 5 Network service related result COdES ccceecce cece eee ee eee teeta eenee teen ene 59 3 6 Control and status COMMANAS cccce eee EA E eas 64 3 7 Control and status result COdES ccc cece eee eee eee netstat e eee enaeas 88 3 8 Mobile Termination error CONtrOl 00 ceee cece cece eee eee ence eee e ene eenee teen ene 89 3 9 Mobile Termination error result code 10 00 cee eeee cece eee eee ee eee etna ee eeetnee ene 89 3 10 Commands for Packet COMA AINS ccc cece eee e eee eee ene ena eas 91 3 11 Packet domains result COde S
68. ble notification presentation lt service gt Description o SSs Phone book service IPhone book service availability sssi lt sSCidY fe SMS service availability wavecom o 2009 Page 154 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual lt service gt Description 2s CBM service availability Clarification If a service becomes available before any AT channel is connected PSREADY notification will be buffered and sent as soon as the first AT channel connects 8 6 3 PSSREP Mobile start up reporting PSSREP lt act gt CME ERROR lt err gt PSSREP PSSREP list of supported lt act gt s OK PSSREP PSSREP lt act gt lt stat gt Parameters Indicates if the module must send an unsolicited code during the startup O The module doesn t send an unsolicited code 1 The module will send an unsolicited code PSSUP This code indicates the status of the module O The module is ready to receive commands for the TE No access code is required 1 The module is waiting for an access code The AT CPIN Command can be used to determine it 2 The SIM card is not present 3 The module is in SIMlock state 4 unrecoverable error 5 unknown state Clarification The mod
69. buted or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom E Smart wireless Smart business WISMO218 AT Command Manual 1 255 Wake up response timer in seconds Default 10 a E window size for Advanced operation with Error Recovery options Default 2 Clarification Value 2 for subset parameter is not supported because CMUX is not running in error recovery mode Refer also to 27 010 for more information on parameters values CMUX parameters are stored in non volatile memory Default value Non volatile memory field l lt mode gt sd loxoo o v_ v Mode o 3 2 Call control commands 3 2 1 CSTA Select type of address Select type of address CSTA lt type gt Get supported types CSTA CSTA list of supported lt type gt s wavecon o 2009 Page 31 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual Parameters International type of address National type of address 3 2 2 CMOD Call mode Select call mode CMOD lt mode gt CMOD CMOD lt mode gt Get supported types CMOD CMOD list of supported lt mode gt s Parameters 129 Proprietary value Multimedia call only without fallback or service change 130 Proprietary val
70. cenan 133 VIP Initialize voice parameter cc cece eee eee eee eect eee eee eaee eens 134 TIAS7S8A commandS 122222222222 5 5 136 General COMMANAS cece cece ee ee eee teeta eet eae 136 Capabilities identification and CONTFOl ccc c ccc cece ence eee ee eee eeeeeeeaeeees 137 Proprietary AT Commands 22 2222 202 00e eens eee eee eee eee eee 140 Capabilities identification and CONTFOl ccc cc cece cence eee na ee eeneeeeeaeeees 140 Flow Control command es iiss sec ies eee eed eee eee Med ee hed iei eee Hes 140 Manufacturer tests command c cee eee eee eee eee eee eee eee senate ents 141 SIM toolkit command and result COdES ccc cece eee eee eee eee teeta 143 CPHS proprietary COMMANAS cccccecc cence eee eee eee e eee e ene e cnet enee teen eneeeaes 146 General purpose proprietary COMMANGAG cccc cece ee eneeeenaeeeeneeeeeaetees 153 Call and network proprietary COMMANGAS ccc cece ence e cena ee eeeeeeeenneees 163 wavecom o 2009 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA _DEV_W218_UGD_003 001 Page 5 172 April 24 2009 wavecom Smart wireless Smart business WISMO218 AT Command Manual 1 AT Commands Description This manual lists detailed information about the AT command set used with the WISMO218
71. ction lt clir gt lt cug gt and characters 7 P D and in lt str gt are ignored Clarification The result code OK can be sent immediately after call setup or only once call is connected to remote party Refer to PSCSSC command for more details If SAT call control modifies the call into an SS or USSD and error is return to the TE wavecom o 2009 Page 108 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual In call modifications by MS are possible when during setup phase two bearer capability list have been negotiated one speech the other multimedia ATD without parameter is used to modify the call from speech to multimedia upgrade of service CONNECT 64000 will be sent is modification succeeds For MO call setup if the semi colon is present then speech mode will be requested first Speech preferred if semi colon is not present multimedia mode will be requested first multimedia preferred 4 1 3 D gt Direct dialling from phone book Initiate a MO call ATD gt lt str gt ATD gt lt mem gt lt n gt Parameters alphanumeric field if possible all available memories should be searched for correct entry lt mem gt Description Se Memory storage ME SIM EE Po i
72. d this setting is possible in case of 3 1 kHz modem and non transparent service wavecom o 2009 Page 33 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 17 83600 bps v 34 4 7 12 14 15 16 17 71 75 79 81 82 83 wavecom os ate Smart wireless Smart business WISM0O218 AT Command Manual 64000 bps multimedia lt name gt Description Data circuit asynchronous UDI or 3 1 kHz modem 1 Data circuit synchronous UDI or 3 1 kHz modem Supported for multimedia calls only Transparent Supported for multimedia calls only Non transparent Clarification Some bearer capabilities computed from CBST parameters are stored in non volatile memory This parameter are used to build the bearer capabilities of the CS data call cf 24 008 10 5 4 5 Parameter name Length Default value Non volatile memory field Information transfer 3 bits Ox02 3 1kHz v_InfoTrans capabilities Connection element 2 bits Ox03 v_ConnElIm non transparent it 0x00 circuit v_TransferMode Synchronous Asynchronous 1 bit oxo1 async v_SyncAsync User Rate 4 bits 0x05 v_UserBearerRate 9 6K 0x00 FNUR n a 3 2 5 CRLP Radio link protocol Select CRLP lt iws gt lt m protocol ws gt lt T1 gt lt N2 gt lt ver gt lt T4 gt wavecom o 2009 Page 34 17
73. d state Default value 4 1 8 P Pulse dialling Pulse Pulse dialling waveconm o 2009 Page 111 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Clarification This command is supported for compatibility purpose and has no effect on ME simple response OK 4 1 9 SO Automatic Answer Description Command Possible Response s Set automatic answer So lt num gt Read current register SO lt num gt value Parameters lt num gt Description 1 255 Number of rings the modem will wait for before answering the phone if a ring is detected 4 1 10 SG Pause before blind dialling Command Possible Response s Set pause duration S6 lt time gt Parameters 0 999 Clarification This command is supported for compatibility purpose and has no effect on ME simple response OK 4 1 11 S7 connection completion timeout Set timeout Read current register S7 lt time gt value wavecon o 2009 Page 112 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Parameters Amount of time t
74. dence gt s list of supported lt delay gt s list of supported lt reliability gt s list of supported lt peak gt s list of supported lt mean gt s lt CR gt lt LF gt CGOMIN lt PDP_type gt list of supported lt precedence gt s list of supported lt delay gt s list of supported lt reliability gt s list of Supported lt peak gt s list of supported lt mean gt s Parameters Refer to CGQREQ Clarification Refer to 6 1 2 for QoS mapping between R99 and R97 R98 Oos 3 10 4 CGATT PS attach or detach Attach or detach CGATT lt state gt 0 O TCGATT TOGAT lt state gt Get supported states CGATT CGATT list of supported lt state gt s Parameters o ema OO 3 10 5 CGACT PDP context activate or deactivate Activate or deactivate a CGACT lt state gt PDP lt cid gt lt cid gt wavecom o 2009 Page 97 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Get current PDPs state CGACT CGACT lt cid gt lt state gt lt CR gt lt LF gt CGACT lt cid gt lt state gt Get supported states CGACT CGACT list of supported lt state gt s Parameters o o Deactivated o Activated PDP Context Identifier PD
75. dentification presentation Connected Line Identification COLP lt number gt lt type gt Presentation lt subaddr gt lt satype gt lt alpha gt Parameters lt number gt Description Integer type Type of address String type subaddress of format specified by lt satype gt Integer type Type of subaddress wavecom o 2009 Page 60 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual String type Alphanumeric representation of lt number gt corresponding to the entry found in phonebook used character set should be the one selected with CSCS 3 5 4 CCWA Calling Line Identification Presentation Call waiting notification CCWA lt number gt lt type gt lt class gt lt alpha gt lt CLlI validity gt lt subaddr gt lt satype gt Parameters lt number gt eoe 4 m _ String type type Phone number number Integer type Type of address String type subaddress of format specified by lt satype gt Integer type type Type of subaddress of subaddress String type Alphanumeric representation of lt number gt corresponding to the entry found in phonebook used character set should be the one selected with CSCS lt class gt Description wavecom o 2009 Page 61
76. dication PSDCI lt Lineld gt lt status gt ssid lt Line Id gt lt status gt wavecom o 2009 Page 148 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Parameters o Disabled CFU notification presentation Enabled CFU notification presentation 2 Query CFU status Line 2 Auxiliary line C e 8 5 4 PSMBNB Mailbox Number PSMBNB lt Line CME ERROR lt err gt Id gt lt number gt lt type gt lt text gt Read mailbox numbers PSMBNB PSMBNB lt Line Id gt lt number gt lt type gt lt text gt Pll lt CR gt lt LF gt PSMBNB lt Line Id gt lt number gt lt type gt lt text gt CME ERROR lt err gt Get supported values PSMBNB PSMBNB list of Supported lt Line Id gt List of supported lt type gt L lt nlength gt lt tlength gt Description The purpose of this command is not to replace CSVM command but to offer more possibilities for Mailbox numbers settings CSVM command allow only voice mailbox settings CPHS define one record per line Set command writes the mailbox number for lt line id gt in SIM If only lt Line Id gt is present in command corresponding record is deleted in SIM wavecom o 2009 Page 149 172 This documen
77. divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISMO218 AT Command Manual 3 Registration denied The GPRS service is disabled the UE is not allowed to attach for GPRS if requested by the user Registered roaming String type Two byte location area code in hexadecimal format e g OOC3 equals 195 in decimal lt ci gt Description String type Two byte cell ID in hexadecimal format wavecom o 2009 Page 106 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 4 ITU T V25 ter commands 4 1 Call control 4 1 1 A Answer Answer a MT cali Clarification In call modifications by network are possible when during setup phase two bearer capability list have been negotiated one speech the other multimedia If call is modify from speech to multimedia CONNECT 64000 is sent to TE If call is modify from multimedia to speech OK is sent to TE 4 1 2 D Dial D lt dialstring gt lt semicolon gt CME ERROR lt err gt call Direct dialling D gt lt str gt lt clir gt lt cug gt lt semicolon gt CME ERROR lt err gt from phonebook name Direct dialling D gt mem lt n gt lt clir gt lt cug gt CME ERRO
78. e gt lt secondtext gt lt email gt are returned with the command Some proprietary commands are implemented to fully manage 3G phonebook wavecom o 2009 Page 75 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 3 6 12 CPBW Write phonebook entry Write entry CPBW lt index gt lt number gt lt type gt lt text CME ERROR lt err gt gt lt group gt lt adnumber gt lt adtype gt lt second text gt lt email gt lt hidden gt Get location CPBW list of ranges and supported lt index gt s lt nlength gt list of supported lt type gt s lt tlength gt lt glengt h gt lt slength gt lt ele ngth gt CME ERROR lt err gt Parameters 0 999 Field of maximum length lt tlength gt Character set as specified by CSCS For other parameters refer to CPBR command Clarification Only first lt group gt lt adnumber gt lt adtype gt lt secondtext gt lt email gt are returned with the command Some proprietary commands are implemented to fully manage 3G phonebook 3 6 13 CCLK Clock CCLK lt time gt CME ERROR lt err gt Get current time CCLK CCLK lt time gt CME ERROR lt err gt Test if command is CCLK supported wavecon
79. eceived messages Get current CNMI CNMI lt mode gt lt mt gt lt bm gt lt ds gt lt bfr gt CNMI CNMI list of supported lt mode gt s list of supported lt mt gt s list of supported lt bm gt s list of supported lt ds gt s list of supported lt bfr gt s Parameters Buffer unsolicited result codes in the TA When TA result code buffer is full The oldest indication is discarded and replaced with the new one when CSMS 0O All indications are buffered when CSMS 1 wavecom o 2009 Page 13 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual 1 Discard indication and reject new received message unsolicited result codes when TA TE link is reserved e g in on line data mode Otherwise forward them directly to the TE Not supported for CBM messages Buffer unsolicited result codes in the TA when TA TE link is reserved e g in on line data mode and flush them to the TE after reservation Otherwise forward them directly to the TE No SMS DELIVER indications are routed to the TE If SMS DELIVER is stored into ME TA indication of the memory location is routed to the TE using unsolicited result code CMTI 2 SMS DELIVERs except class 2 messages and messages in the message waiting indica
80. ed locations in selected memory Integer type Value indicating the total number of locations in selected memory Clarification SMI corresponds to SIM UICC phonebook global phonebook If a SIM card is present or if a UICC with an active GSM application is present the EFADN under DFTelecom is selected If a UICC with an active USIM application is present the global phonebook DFPHONEBOOK under DFTelecom is selected AP corresponds to selected application phonebook local phonebook If a UICC with an active USIM application is present the application phonebook DFPHONEBOOK under ADFUSIM is selected wavecom o 2009 Page 72 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart business WISM0O218 AT Command Manual 3 6 10 CPBR Read phonebook entries Read CPBR lt index1 gt lt index2 gt CPBR lt index1 gt lt number gt lt type gt entries lt text gt lt hidden gt lt group gt lt adnumber gt lt adtype gt lt secondtext gt lt email gt E lt CR gt lt LF gt CPBR lt index2 gt lt number gt lt type gt lt text gt lt hidden gt lt group gt lt adnumber gt lt adtype gt lt secondtext gt lt email gt CME ERROR lt err gt Get CPBR location list of Supported lt index gt s l
81. en initiated by STK no AT channel is associated to the call Examples MO speech alerting at distant and initiated on line 7 PSCSCS 1 4 1 1 MO speech call connected to 11111111 and active on line 7 PSCSCS 1 5 1 1111111 129 1 MT data call connected to 123456 and active on line 1 BC list A28881211563AG6 PSCSCS 8 14 1 123456 129 1 A28881211563A6 8 7 2 CNAP Command Calling Name Presentation Get status of CNAP CNAP CLIR lt n gt lt m gt Get supported values CNAP CNAP list of supported lt n gt s wavecom o 2009 Page 168 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ate Smart wireless Smart business WISM0O218 AT Command Manual Parameters lt n gt Description CNAP notification is disabled Enabled unsolicited result code CNAP lt name gt lt validity gt lt m gt Description Network does not provide the CNAP service Network provides the CNAP service Unknown e g no network etc o _____ Namepresentation allowed Ci Name presentation restricted Clarification CNAP Calling Name Presentation is a supplementary service provided by the network CNAP command enables or disables the presentation of the name provided by the network 8 7 3 PSFSNT Field strength notification
82. esponses in verbose format 4 3 7 X Result code selection and call progress monitoring Command Possible Response s Set result code X lt result gt selection Parameters CONNECT result code is given upon entering online data state Dial tone and busy detection are disabled 1 CONNECT lt text gt result code is given upon entering online data state Dial tone and busy detection are disabled 2 CONNECT lt text gt result code is given upon entering online data state Dial tone detection is enabled and busy detection is disabled CONNECT lt text gt result code is given upon entering online data state Dial tone detection is disabled and busy detection is enabled 4 CONNECT lt text gt result code is given upon entering online data state Dial tone and busy detection are both enabled 4 3 8 amp C DCD behaviour Set DCD behaviour amp C lt behaviour gt Parameters DCE always presents the ON condition on circuit 109 Ho Circuit 109 changes in accordance with the underlying DCE wavecom o 2009 Page 122 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ae Smart wireless Smart business WISM0O218 AT Command Manual 4 3 9 amp D DTR behaviour Set DTR behaviour amp D lt behaviour gt Parameters Ce 0 ignores circuit DCE ignores circuit 108 2 0
83. eypad event reporting oe No display event reporting O default No indicator event reporting wavecom o 2009 Page 70 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Indicator event reporting using result code CIEV lt ind gt lt value gt lt ind gt indicates the indicator order number as specified for CIND and lt value gt is the new value of indicator Indicator event reporting using result code ClEV lt ind gt lt value gt All indicator events shall be directed from TA to TE a buffer of unsolicited result codes defined within this oOo o is cleared when lt mode gt 1 3 is entered 3 6 9 CPBS Select phonebook memory storage Select phonebook CPBS lt storage gt CME ERROR lt err gt memory storage Get current memory CPBS CPBS storage status lt storage gt lt used gt lt total gt CME ERROR lt err gt Get supported storages CPBS CPBS list of supported lt storage gt s Parameters DC MIT dialled calls list CPBW may not be applicable for this storage SIM USIM or MT emergency number CPBW is not be applicable for this storage SIM USIM fixed dialling phonebook If a SIM card is present or if a UICC with an active GSM application is present the information in
84. f period and duty cycle for buzzer are 250 100 8 7 Call and network proprietary commands 8 7 1 PSCSCN Call state change notification Select notification PSCSCN lt mode gt CME ERROR lt err gt presentation mode PSCSCN PSCSCN lt mode gt Description This command allows presentation of information about CS call states as well as audio or in call notifications related to current call This command does note replace CLCC command TE is notified whenever the state of a call changes this avoid TE to use polling mechanism with CLCC command to know the states of each call When lt mode gt 0O set command disables both the presentation of call state change URC PSCSC and call notification URC PSCN When lt mode gt 1 set command enable the presentation of call state change URC wavecomn o 2009 Page 163 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISMO218 AT Command Manual PSCSC every time the states of a call change When lt mode gt 2 set command enables both the presentation of call state change URC PSCSC and call notification URC PSCN every time audio or in call notification occurs in band SS notify Call state change PSCSC lt Call Id gt lt State gt lt Status gt lt Number gt lt type g
85. for the text mode Hs Send RP ACK or buffered result code received correctly 2 Send RP ERROR Acknowledgement TPDU not supported Clarification This command is allowed only if CSMS lt service gt is set to 1 and is used to acknowledge SMS received from network Routing of SWS DELIVER and SMS STATUS REPORT to ME TA depends on both CSMS configuration as well as lt mt gt and lt ds gt values of CNWMII In PDU acknowledgement TPDU is not supported The following table summarizes the SMS DELIVER notification modes according to these parameters CNMI lt mt gt CSMS lt service gt O CSMS lt service gt 1 ee When SMS Mode O SMS acknowledgement and storage are managed internally by MS whatever their class if needed they will be stored in SIM When SMS DELIVER Mode 1 SMS with no message class class O class 1 class 3 are sent to ME TA for acknowledgement CNMA expected they will not be stored in ME it s up to TE to store them SMS class 2 amp message waiting indication group Store or Discard are managed internally by MS if needed they will be stored in SIM no CNMA expected When SMS DELIVER Mode 2 SMS class 3 are sent to ME TA for acknowledgement CNMA expected they will not be stored in ME it s up to TE to store them SMS with no message class class O class 1 class 2 amp message in waiting group are managed internally by MS if needed they will be stored in SIM no CNMA expected F
86. gt and lt UTRAN AcT gt appears in 27 007 Release 5 wavecom o 2009 Page 57 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 3 4 18 CPLS Selection of preferred PLMN list Select the list of CPLS lt list gt CME ERROR lt err gt preferred PLMIN for CPOL Get current list CPLS CPLS lt list gt CME ERROR lt err gt Get supported values CPLS CPLS list of Supported lt list gt s CME ERROR lt err gt Parameters User controlled PLMIN selector with Access Technology EFPLMNWAcT if not found in the SIM UICC then PLMN preferred list EFPLMNsel this file is only available in SIM card or GSM application selected in UICC Operator controlled PLMIN selector with Access Technology EFOPLMNwAcT Clarification Note This command appears in 27 007 Release 5 but SIM files EFPLMNwAcT EFOPLMNwWAcT exists in Release 99 3 4 19 COPN Read operator names COPN lt numeric1 gt lt alpha1 gt lt CR gt lt LF gt COPN lt numeric2 gt lt alpha2 gt CME ERROR lt err gt Parameters lt numericn gt Description String type type Operator in numeric format see COPS wavecom o 2009 Page 58 172 This document is the sole and exclusive property of WWAVECOM Not to be dist
87. he modem will wait for the carrier signal from the remote modem If a carrier is not received in this time the modem will hang up and send the NO CARRIER result code 4 1 12 S8 Comma dial modifier Set time time Isg lt time gt lt time gt Read current register lt time gt value Parameters 0 255 The value of this register determines how long the modem should pause when it sees a comma in the dialling string Clarification Comma modifier is not supported in dial string this command has no effect on ME simple response OK 4 1 13 S10 Automatic disconnect delay Set time o time S10 lt time gt lt time gt Read current register S10 lt time gt value Parameters 0 255 Amount of time from when the modem recognizes a loss of carrier to when it will hang up Clarification This command is supported for compatibility purpose and has no effect on ME simple response OK wavecom o 2009 Page 113 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 4 1 14 T Tone dialling Setdialtone Tooo ooo d Clarification This command is supported for compatibility purpose and has no effect on ME simple response OK 4 2 General TA control commands 4 2 1 A Repeat last command Re
88. hold has been released this is not a SS notification during a voice call Call is being connected alerting with the remote party in alerting state in explicit call transfer operation during a voice call Call has been connected with the other remote party in explicit call transfer operation during a voice call or MT call setup This is a deflected call MIT call setup 3 6 Control and status commands 3 6 1 CPAS Phone activity status Command Possible Response s Get activity status CPAS CPAS lt pas gt CME ERROR lt err gt Get supported values CPAS CPAS list of supported lt pas gt s CME ERROR lt err gt wavecom o 2009 Page 64 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wevecom Z Smart wireless Smart business WISMO218 AT Command Manual Parameters oC Ready MT allows commands from TA TE a Unknown MT is not guaranteed to respond to instructions 2 3 Ringing MIT is ready for commands from TA TE but the ringer is active 4 Call in progress MT is ready for commands from TA TE but a call is in progress 3 6 2 CFUN Set phone functionality Select the level of CFUN lt fun gt lt rst gt CME ERROR lt err gt functionality Get current level CFUN CFUN lt fun gt CME ERROR lt err gt Get supported values CFUN
89. ic Unit 201 207 2nd Floor Bio Informatics Centre No 2 Science Park West Avenue Hong Kong Science Park Shatin New Territories Hong Kong PRC Tel 852 2824 0254 Fax 852 2824 0255 Online contact details GPS and maps waoveconm Smart wireless Smart business
90. iness WISM0O218 AT Command Manual 3 2 6 CR Service reporting Select service reporting CR lt mode gt a an Set eurent mode _ supported modes CR list of supported lt mode gt s Parameters 3 2 7 CEER Extended error report Get last error Get last error report CEER sd CEER CEER lt report gt sd Test if command is CEER supported Parameters String type String CauseSelect lt cs gt Cause lt c gt is returned lt cs gt and lt c gt are numbers representing the CauseSelect and Cause CauseSelect lt cs gt Cause lt c gt wavecom o 2009 Page 36 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual CauseSelect lt cs gt Cause lt c gt 35 Local couse 66 MM network cause See 24 008 67 CC network cause See 24 008 69 RP cause See 24 008 71 SIM cause 7 Technical problem 11 Command not allowed wavecom o 2009 Page 37 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ate Smart wireless Smart business WISM0O218 AT Command Manual CauseSelect lt cs gt Cause lt c gt PF _ YS Sa
91. ing to rules of Annex A backspace can be used to delete last character and carriage returns can be used previously mentioned four character sequence shall be sent to the TE after every carriage return entered by the user if lt dcs gt indicates that 8 bit or UCS2 data coding scheme is used or lt fo gt indicates that TP User Data Header Indication is set the entered text should consist of two IRA character long hexadecimal numbers which ME TA converts into 8 bit octet e g two characters 2A IRA 50 and 65 will be converted to an octet with integer value 42 In PDU mode The PDU shall be hexadecimal format similarly as specified for lt pdu gt and given in one line ME TA converts this coding into the actual octets of PDU When the length octet of the SMSC address given in the PDU equals zero the SMSC address set with command Service Centre Address CSCA is used in this case the SMSC Type of Address octet shall not be present in the PDU i e TPDU starts right after SMSC length octet Sending can be cancelled by giving lt ESC gt character IRA 27 lt ctrl Z gt IRA 26 must be used to indicate the ending of the message body or PDU Text length is limited to PDU max length 164 wavecon o 2009 Page 20 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_ 003 001 April 24 2009 wavecom ee Smart wireless
92. ion type gt A string that represents the type of notification proactive command name received from the SIM Some command requires the use of PSSTK set command to send a response to the SIM LANGUAGE Sent on reception of APPI_LSTK_LANGUAGE _NOTIFICATION_IND NOTIFICATION CONTROL BY SIM Sent on reception of APPI_LSTK_CONTROL_BY_SIM_IND Sent on reception of APPI_LSTK_REFRESH_IND Sent on reception of APPI_LSTK_END_CALL_IND Sent on reception of APPI_LSTK_PROCESSING_IND Sent on reception of APPI STK END SESSION IND ABORT SESSION Sent on reception of APPI STK ABORT SESSION IND NOTIFICATION Sent on reception of APPI_LSTK_NOTIFICATION_IND Sent on reception of APPI CALL ASYNC_ DISCONNECT IND Require use of PSSTK set command to respond to SIM SETUP CALL Sent on reception of APPILSTK_SETUP_CALL_IND Require use of PSSTK set command to respond to SIM Sent on reception of APPI_LSTK_DISPLAY_TEXT_IND Require use of PSSTK set command to respond to SIM GET INKEY Sent on reception of APPI_STK_GET_INKEY_IND Require use of PSSTK set command to respond to SIM GET INPUT Sent on reception of APPI_STK_GET_INPUT_IND Require use of PSSTK set command to respond to SIM PLAY TONE Sent on reception of APPI_LSTK_PLAY_TONE_IND Require use of PSSTK set command to respond to SIM SELECT ITEM Sent on reception of APPI_STK_ SELECT _ITEM_IND Require use of PSSTK set command to respond to SIM REMOVE MENU Sent on reception of APPILSTK REMOVE MENU _
93. is document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual VOICE AUX Proprietary value for ALS CPHS Alternate line service Used in case of incoming on line 2 Refer to PSALS MULTIMEDIA Proprietary value Multimedia call only MULTIMEDIA FALLBACK Proprietary value Analog multimedia calls with possible fallback to speech MULTIMEDIA VOICE Proprietary value UDI RDI multimedia calls with possible fallback and service change multimedia mode preferred VOICE MULTIMEDIA Proprietary value UDI RDI multimedia calls with possible fallback and service change voice mode preferred Clarification Optional parameters lt priority gt lt subaddr gt lt satype gt are not supported in CRING Note If alternate line service is activated lt type gt VOICE if speech call is on line 1 and VOICE AUX if call is on line 2 3 4 Network service related commands 3 4 1 CNUM Subscriber number CNUM lt alpha1 gt lt number1 gt lt type1 gt lt speed gt lt se rvice gt lt itc gt lt CR gt lt LF gt CNUM lt alpha2 gt lt number2 gt lt type2 gt lt speed gt lt service gt lt itc gt Parameters String type Alphanumeric string associated with lt numberx gt used character set should be the one se
94. is not activated refer to COLP result code for ATD can be sent as soon as call set up is started or after call is connected to the called party after successful call set up wavecom o 2009 Page 170 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Set command allows selection of lt mode gt for MO speech call result code If user set lt mode gt 1 when COLP is also activated ERROR will be returned Mode will remains to O Parameters O OK is returned only when call is connected to the remote party Default 1 OK is returned when call setup is started The user is not informed of call successful connection to remote party If the call fails NO_ANSWER or NO_CARRIER will be sent after the OK 8 7 5 PSCCDN Call connection and disconnection notification Set mode ss PSCCDN lt mode gt 0 Get current mode PSCCDN PSCCDN lt mode gt Get supported values PSCCDN PSCCDN list of Supported lt modes gt s List of supported lt status gt s Description This command allows presentation of information about connection or disconnection of a CS call either MT or MO This URC allow TE to exactly know which call is being connected or disconnected NO CARRIER urc is not sufficient to discri
95. is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual 1 5 QOS reliability class Default value 3 QOS peak throughput class subscribed value QOS peak throughput class lt mean gt Description O default QOS mean throughput class subscribed value 1 18 aos mean throughput class 31 Jaos mean throughput class best effort Clarification Refer to 6 1 2 for QoS mapping between R99 and R97 R98 Qos 3 10 3 CGOQOMIN Quality of Service Profile Minimum acceptable Set minimum QOS CGOMIN lt cid gt R97 lt precedence gt lt delay gt lt reliability gt lt peak gt lt mean gt Get current settings CGOMIN CGOMIN lt cid gt lt precedence gt lt delay gt lt reliability gt lt peak gt lt mean gt lt CR gt lt LF gt CGQMIN lt cid gt lt precedence gt lt delay gt lt reliability gt lt peak gt lt mean gt wavecom o 2009 Page 96 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Get supported values CGQOMIN CGQOMIN lt PDP_type gt list of supported lt prece
96. l format e g OOC3 equals 195 in decimal lt ci gt Description String type Two byte cell ID in hexadecimal format wavecom o 2009 Page 102 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ates Smart wireless Smart business WISM0O218 AT Command Manual 3 10 11 CGSMIS Select service for MO SMS messages Set SMS service CGSMS lt service gt CGSMS O NEE Get supported values CGSMS CGSMS list of currently available lt service gt s Parameters lt service gt Ear oa o o Packet Domain eee Domain 2 Packet Domain preferred use circuit switched if GPRS not available 3 Circuit switched preferred use Packet Domain if circuit switched not available Clarification When lt service gt value is 2 the SMS is sent on GPRS network if already attached Otherwise it is sent on circuit switched network If an error occurs on the GPRS network no further attempt is made 3 10 12 Request Packet Domain service D Request packet D 99 lt called_address gt CONNECT domain service lt L2P gt lt cid gt Parameters String type Called party in the address space applicable to the PDP Only empty string is allowed ee ee wavecom o 2009 Page 103 172 This document is the sole and exclusive property of WAVECOM Not to be dis
97. ld InformationsNumbers of CSP file is OxFF use of AT PSCSP To check Service Group D5 Otherwise CME ERROR lt err gt is returned Parameters lt index gt Description lt index1 gt lt index2 gt 0 255 Index of information number phonebook entry lt number gt Description String type Phone number of format lt type gt Integer type Type of address String type Field of maximum length lt tlength gt Character set as specified by CSCS Integer type Representation of the Network specific indicator Integer type Representation of Premium service indicator Integer type Representation of the level of the record in the tree Integer type Value indicating the maximum length of field lt number gt wavecom o 2009 Page 152 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual Integer type Value indicating the maximum length of field lt text gt 8 6 General purpose proprietary commands 8 6 1 PSPRAS Pin Remaining Attempt Status ISetcommand command PSPRAS o O Get remaining PIN PSPRAS oe lt pin1 gt attempts lt puk1 gt lt pin2 gt lt puk2 gt CME ERROR lt err gt Get supported codes PSPRAS PSPRAS list of supported lt code gt Description This command is used to get the nu
98. lected with CSCS wavecom o 2009 Page 40 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom n Smart wireless Smart business WISMO218 AT Command Manual lt numberx gt Description Integer type Type of address Integer type Same as CBST lt service gt Description e O Taea O Fax 3 4 2 CREG Network registration Control CREG CREG lt n gt notification Get current registration CREG CREG lt n gt lt stat gt lt lac gt lt ci gt status CME ERROR lt err gt Get supported values CREG CREG list of supported lt n gt s wavecom o 2009 Page 41 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual Parameters 1 Disable network registration unsolicited result code Enable network registration and location information unsolicited result code CREG lt stat gt 2 Enable network registration and location information unsolicited result code CREG lt stat gt lt lac gt lt ci gt not registered MIT is not currently searching a new operator to register to Registered home network 2 Not registered but MITT is currently sea
99. lt sn gt Description String type IMEI 4 3 TA TE interface commands 4 3 1 E Echo Parameters lo Characters echo disabled 4 Characters echo enabled 4 3 2 Q Result code suppression Parameters lt result gt Description loss Result codes are transmitted to TE Result codes suppressed 4 3 3 S3 Line termination character Set line termination S3 lt char gt character wavecom o 2009 Page 120 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom es Smart wireless Smart business WISM0O218 AT Command Manual Parameters Termination character lt CR gt 4 3 4 S4 Response formatting character Set response S4 lt char gt Caen 7 character Parameters 10 Termination character lt LF gt sss character lt LF gt 4 3 5 S5 Line editing character Set line editing S5 lt char gt ae Parameters Bs Termination character lt BS gt 4 3 6 V TA response format Set response format __Vicformats ee waveconm o 2009 Page 121 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual Parameters oo Responses in numeric format R
100. lue Length Non volatile memory field overies Jooo ____ V DsRcorerot_ wavecom o 2009 Page 116 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart business WISM0O218 AT Command Manual Command Default value Length Non volatile memory field lt storage gt 0x53 Ox4D 3 bytes a_atp Storage Ox0O 0x00 1 byte v_hee_SmsVp s_RelTime v_NbMinutes 0x18 1 byte v_hee_SmsVp s_RelTime v_NbHours 0x00 1 byte v_hee_ SmsVp s_RelTime v_NbDays 0x00 1 byte v_hee_SmsVp s_RelTime v_NbWeeks Ox00 0x00 20 v_hee_SmsVp s_RelTime bytes v_Gap_RelativeTime CSME CBST lt speed gt 0x05 v_UserBearerRate Ox02 v_InfoTrans 0x00 v_Fnur CBST lt name gt 0x01 1 bit v_SyncAsync 0x00 1 bit v_TransferMode CMOD lt mode gt oxoo 2 bits _ v_CallMode CMEE lt n gt oxoo 2 bits v cmeE CREG kn gt oxoo 2 bits v_crEGn wavecom o 2009 Page 117 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Command Default value Length Non volatile memory field TOMER 4 2 5 GCAP Complete capabilities list Command Possible Response s
101. mber of remaining PIN and PUK attempts Set command has no effect returns OK Parameters Number of remaining attempts for PIN 1 l0 3 Number of remaining INumber of remaining attempts for PIN2 sd for PIN 2 o0 Number of remaining attempts for PUK 1 o o Number of remaining attempts for PUK 2 wavecom o 2009 Page 153 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual SIM PINI PIN1 PIN 1 IPIN 1 identifier eee SIM PIN2 PIN 2 identifier SIM PUK1 PUK 1 identifier SIM PUK2 PUK 2 identifier 8 6 2 PSSEAV Service Availability PSSEAV lt mode gt Get current mode PSSEAV EE lt mode gt lt CR gt lt LF gt PSREADY lt service gt lt CR gt lt LF gt PSREADY lt service gt Get supported modes PSSEAV PSSEAV list of Supported modes list of supported services Description Set command enables disables the presentation of notification result code from ME to TE When lt mode gt 1 PSREADY result code is sent to TE when lt service gt is available Read command is used to get current mode and to check which service are already available PSREADY is returned only for available services Parameters o Disable notification Disable notification presentation 2 cn Ena
102. minate calls id Set command enables disables the presentation of notification result code from ME to TE When lt mode gt 1 PSCALL result code is sent to TE on connection or disconnection of call lt Call Id gt Call notification PSCALL lt Call Id gt lt Status gt lt Number Parameters i esiiensaicaies Een en Wa vecon o 2009 Page 171 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ae Smart wireless Smart business WISMO218 AT Command Manual los Waiting call alerting no call id assigned yet _ oisconnested SSCS lt number gt Description String type Phone number when lt status gt 1 Clarification Special case to inform that current waiting call has been disconnected PSCALL O O is sent The CLCC command can be used to get more information about a specific call wavecom o 2009 Page 172 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 WAVECOM S A 3 esplanade du Foncet 92442 Issy les Moulineaux France Tel 33 1 46 29 08 00 Fax 33 1 46 29 08 08 Wavecom Inc 430 Davis Drive Suite 300 Research Triangle Park North Carolina USA Tel 1 919 237 4000 Fax 1 919 237 4140 WAVECOM Asia Pacif
103. n or not detectable Clarification The lt ber gt is provided only in online mode 3 6 6 CMEC Mobile Termination control mode Select equipment CMEC lt keyp gt lt disp gt lt ind gt CME ERROR lt err gt Get current CMEC CMEC settings lt keyp gt lt disp gt lt ind gt CMEC list of supported lt keyp gt s list of supported lt disp gt s list of supported lt ind gt s Parameters MT can be operated only through its keypad execute command of CKPD cannot be used Only MIT can write to its display command CDIS can only be used to read the display wavecom o 2009 Page 68 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Only MT can set the status of its indicators command CIND can only be used to read the indicators 3 6 7 CIND Indicator control Set MT indicators CIND lt ind gt lt ind gt CME ERROR lt err gt Get MT indicator CIND CIND lt ind gt lt ind gt status CME ERROR lt err gt Get supported values CIND CIND lt descr gt list of supported lt ind gt s lt descr gt list of supported lt ind gt s CME ERROR lt err gt Parameters Integer type Range of corresponding lt descr gt lt de
104. nebook used character set should be the one selected with CSCS 3 4 17 CPOL Preferred PLMN list Write an entry CPOL lt index gt CME ERROR lt err gt lt format gt lt oper gt lt GS M_AcT gt lt GSM_Compact _AcT gt lt UTRAN_AcT gt List all entries CPOL CPOL lt index1 gt lt format gt lt oper1 gt lt GSM_AcT1 gt lt GSM_Compact_AcT1 gt lt UT RAN AcT1 gt lt CR gt lt LF gt CPOL lt index2 gt lt format gt lt oper2 gt lt GSM _AcT2 gt lt GS M_Compact_AcT2 gt lt UTRAN _AcT2 gt CME ERROR lt err gt CPOL list of supported lt index gt s list of supported lt format gt s CME ERROR lt err gt wavecom o 2009 Page 56 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Parameters Integer type The order number of operator in the SIM USIM preferred operator list loss Long format alphanumeric lt oper gt Short format alphanumeric lt oper gt String type lt format gt indicates if the format is alphanumeric or numeric see COPS Cee technology not selected 1 Access technology selected Access technology not selected Ce technology not selected 1 Access technology selected Clarification Note lt GSM_AcT gt lt GSM_Compact_AcT
105. ned To set up a recurrent alarm for one or more days in the week the lt recurr gt parameter may be used When an alarm is timed out and executed the unsolicited result code CALV lt n gt is always returned Read command returns the list of current active alarm settings in the MT Test command returns supported array index values alarm types and maximum length of the text to be displayed 3 6 29 CALD Delete alarm CALD lt n gt CME ERROR lt err gt CALD CALD list of supported lt n gt s CME ERROR lt err gt Parameters integer type value indicating the index of the alarm default is manufacturer specific Clarification Action command deletes an alarm in the MT If the command fails in an MT error CME ERROR lt err gt is returned Test command returns supported array index values wavecom o 2009 Page 87 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 3 7 Control and status result codes 3 7 1 CCWV Call Meter warning value Call meter warning value CCWV Parameters lt ccm gt Description String type Three bytes of the current call meter value in hexadecimal format e g 00001E indicates decimal value 30 value is in home units and bytes are similarly coded as ACMmax value in
106. ng type IP address Format lt n gt lt n gt lt n gt lt n gt where lt n gt 0 255 If the value is null or equals 0 0 0 0 a dynamic address will be requested The allocated address may be read using the CGPADDR command wavecom o 2009 Page 92 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual PDP data compression off Default if value is omitted PDP header compression off Default if value is omitted Clarification For lt cid gt 1 2 and 3 PDP context definition is stored in EEPROM i e parameters provided in CGDCONT for PDP context definition and PDP context status defined undefined are stored in non volatile memory If a PDP has been defined with CGDCONT after a switch off switch on AT CGDCONT will list the PDP has defined lt cid gt 3 is locked This means that TE is not allowed to modify definition and parameters of lt cid gt 3 with CGDCONT set command This gives a default PDP context with parameters that TE cannot change Default parameter are located in t_hee_atp_ PDPContext section lt cid gt 3 is also the default lt cid gt if CGDCONT with lt cid gt omitted is received lt cid gt 3 will be used For lt cid gt 1 2 and 3 the following parameters are stored in non volatile mem
107. no effect on ME simple response OK 5 1 7 W Extended Result code Set extended result W lt mode gt code Parameters o fonty result code CONNECT supported 5 2 Advanced Hayes commands 5 2 1 amp K Extended Flow control option Parameters o Disable all Disable all flow control sssi CsSSsidY control Enable bi directional hardware flow control Only supported over USB 4 Enable XON XOFF flow control Only supported over USB wavecom o 2009 Page 129 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart business WISM0O218 AT Command Manual 5 2 2 amp S DSR option Set DSR option Parameters Causes DSR signal to be active at all times Dench value Causes DSR signal to be active after answer tone has been detected and inactive after the carrier has been lost Clarification Parameter stored by amp W command 5 2 3 amp V Configuration profile Display active profile amp V lt profile gt Parameters O Display the ACTIVE PROFILE STORED PROFILE 1 and STORED Default value PROFILE O 5 2 4 amp W Store Active profile Store active profile amp Wf lt profile gt Parameters Store the current configuration in profile O E value ao Store the current configuration in profile 1 wavecom
108. ollowing table summarizes the STATUS REPORT SR notification modes according to CSMS and lt ds gt parameters waveconm o 2009 Page 16 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual CNMI lt ds gt CSMS lt service gt O CSMS lt service gt 1 lo STATUS REPORT mode 0 STATUS REPORT mode O 1 STATUS REPORT mode 0 STATUS REPORT mode 1 When STATUS REPORT Mode When STATUS REPORT Mode and storage Refer also to CMT URC description for waiting message indication treatment O MS manages SR internally 1 SR are sent to ME TA for acknowledgement 2 3 3 CNIGL List Messages List messages CMGL lt stat gt if text mode CMGF 1 command successful CMGL lt index gt lt stat gt lt oa da gt lt alpha gt lt scts gt lt tooa toda gt lt length gt lt CR gt lt LF gt lt da ta gt lt CR gt lt LF gt CMGL lt index gt lt stat gt lt da oa gt lt alpha gt lt scts gt lt tooa toda gt lt length gt lt CR gt lt LF gt lt da ta gt if PDU mode CMGF 0 and command successful CMGL lt index gt lt stat gt lt alpha gt lt length gt lt C R gt lt LF gt lt pdu gt lt CR gt lt LF gt CMGL lt index gt lt s tat gt lt alpha gt lt length gt lt CR gt l
109. ontext Identifier wavecom o 2009 Page 100 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart business WISM0O218 AT Command Manual String type IP address Format lt n gt lt n gt lt n gt lt n gt where lt n gt 0 255 Restriction Set command return address provided by the network if a connection has been established 3 10 9 CGCLASS GPRS mobile station class Set mode of operation CGCLASS lt class gt CGCLASS CGCLASS lt class gt Get supported mode CGCLASS CGCLASS list of supported lt class gt s Parameters lt class gt Description Class A mode of operation A Gb mode or CS PS mode of operation lu mode highest mode of operation MT would operate simultaneous PS and CS service Class B mode of operation A Gb mode not applicable in lu mode MT would operate PS and CS services but not simultaneously CG Class C mode of operation in PS only mode A Gb mode or PS mode of operation lu mode MT would only operate PS services Class C mode of operation in CS only mode A Gb mode or CS lu mode lowest mode of operation MT would only operate CS services 3 10 10 CGREG GPRS network registration status Set registration CGREG lt n gt notification mode Get current registration CGREQ
110. or not does not provoke tool detection procedure 8 6 6 PSRDBS Radio band settings Set radio bands PSRDBS lt mode gt CME ERROR lt err gt L lt GSM band gt lt UMTS band gt o Peaneee PSRDBS lt GSM band gt lt UMTS band gt Get supported values PSRDBS PSRDBS list of supported lt mode gt s list of supported lt GSM band gt s list of supported lt UMTS band gt s Description Set command is used to set the radio band s When lt mode gt 0 band settings are taken into account only at next switch on When lt mode gt 1 a stack restart is performed to select immediately the requested wavecom o 2009 Page 157 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual settings Parameters O Set radio bands will be taken into account at next switch on Default 1 Set radio bands a stack restart is performed to take into account the new selected bands E GSM s b es1soo S 16 Bit field type parameter to set several bands sum up the values 1o UMTS band 1 2 UMTSbana2 Bit field type parameter to set several bands sum up the values Clarification Example To set GSM 900 amp PCS1800 for GSM and band 1 2 3 for UMTS AT PSRDBS 1 10 7 OK 8 6 7 PSADC A D Convert
111. ory Parameter Length Default Non volatile memory field name value wavecom o 2009 Page 93 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 weaevecom a Smart wireless Smart business WISM0O218 AT Command Manual Parameter Length Default Non volatile memory field name value lt Guaranteed 1 byte 0x00 v_hee_PDPCtxtQosGuaranteedDLBitRate bitrate DL gt lt Guaranteed 1 byte 0x00 v_hee_PDPCtxtQosGuaranteedULBitRate bitrate UL gt lt Traffic 2 bits 0x00 v_hee_PDPCtxtQosTrafficHandling handling priority gt lt Transfer 6 bits 0x00 v_hee_PDPCtxtQosTransferDelay delay gt lt SDU error 4 bits 0x00 v_hee_PDPCtxtQosSDUErrorRatio ratio gt lt Residual bit 4 bits 0x00 v_hee_PDPCtxtQosResidualBER error ratio gt lt Maximum 1 byte 0x00 v_hee_PDPCtxtQosMaxDLBitRate bitrate DL gt lt Maximum 1 byte 0x00 v_hee_PDPCtxtQosMaxULBitRate bitrate UL gt lt Maximum 1 byte 0x00 v_hee_PDPCtxtQosMaxSDUSize SDU size gt lt Delivery of 3 bits 0x00 v_hee_PDPCtxtQosDeliveryErrSDU erroneous SDUs gt lt Delivery 2 bits 0x00 v_hee_PDPCtxtQosDeliveryOrder order gt 3 10 2 CGOQOREO Quality of Service Profile Requested Set requested QOS CGOREQ lt cid gt R97 lt precedence gt lt delay gt lt reliability gt lt peak gt lt mean gt wavecom o 2009
112. ot to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual 148 Barring of outgoing international calls expect those directed to home PLMN 153 Barring of incoming calls 154 Barring of all incoming calls 155 Barring of incoming calls when roaming outside home PLMN country eee s NJA O W Alerting pattern category 1 Alerting pattern category 2 wavecom o 2009 Page 167 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISMO218 AT Command Manual Ise Alerting pattern category 3 7 Alerting pattern category 4 8 Alerting pattern category 5 Clarification This command uses information available at APPI interface application i f AT parser does not interface directly with protocol stack so it does not have immediate access to L3 messages this means that lt state gt does not match L3 messages exactly as they are defined in 24 008 recommendation e SIM toolkit SET UP CALL Values 30 33 for lt state gt are used when a SET UP CALL proactive command has been received from the SAT This call is initiated internally in the ME by STK PSCSCS notification will be broadcasted as URC the MO call has be
113. peat the last A command line 4 2 2 Identification information Request identification I lt value gt lt text gt information Parameters lt value gt Description O default Get model identifier wavecom o 2009 Page 114 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart business WISM0O218 AT Command Manual 4 2 3 Z Reset default configuration Reset to default Z lt value gt configuration Parameters Restore profile O Pen value Clarification Parameter impacted by Z command Default value Non volatile memory field SS E E E Vv i omes o oor O versos CS eo kbehavior gt foxo Iv DTRBehavour en e fren SO so si 7 fstines foros fas cei wavecom o 2009 Page 115 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ate Smart wireless Smart business WISM0O218 AT Command Manual Default value Non volatile memory field 4 2 4 amp F Factory defined configuration Reset to factory amp F lt value gt configuration Parameters O Set to factory configuration Default value Clarification Parameter impacted by amp F command Command Default va
114. peed gt CME ERROR lt err gt L lt N1 gt lt T1 gt L lt N2 gt lt T2 gt lt T3 gt lt k gt 1 CMUxX lt mode gt lt subset gt lt port_speed gt lt N1 gt lt T1 gt lt N2 gt lt T2 gt lt T3 gt lt k gt CME ERROR lt err gt CMUxX list of supported lt mode gt s list of supported lt subset gt s list of supported lt port_speed gt s list of supported lt N1 gt s list of supported lt T1 gt s list of supported lt N2 gt s list of supported lt T2 gt s list of supported lt T3 gt s list of supported lt k gt s Parameters Advanced option wavecom o 2009 Page 29 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual O UIH frames used only default UI frames used only C ieat coo nits OSSCSC S S S S S 1 32768 Maximum frame size Default 31 64 if Advanced option is used 1 255 Acknowledgement timer in units of ten milliseconds Default 10 100 ms 0 100 Maximum number of re transmissions Default 3 Response timer for the multiplexer control channel in units of ten milliseconds Default 30 wavecom o 2009 Page 30 172 This document is the sole and exclusive property of WAVECOMI Not to be distri
115. ported Parameters For all other parameters refer to CMT URC description In text mode lt scts gt is not supported in PDU mode lt ackpdu gt is not supported wavecom o 2009 Page 19 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom s Smart wireless Smart business WISMO218 AT Command Manual Clarification In text mode entered text is sent to address lt da gt and all current settings refer to CSMP and CSCA are used to construct the actual PDU in ME TA In PDU mode lt length gt must indicate the number of octets coded in the TP layer data unit to be given i e SMSC address octets are excluded The TA sends a four character sequence lt CR gt lt LF gt lt greater_than gt lt space gt IRA 13 10 62 32 after command line is terminated with lt CR gt after that text can be entered or PDU can be given from TE to ME TA The DCD signal shall be in ON state while text or PDU is entered The echoing of entered characters back from the TA is controlled by V 25ter echo command E In text mode the entered text should be formatted as follows if lt dcs gt set with CSMP indicates that GSM 7 bit default alphabet is used and lt fo gt indicates that TP User Data Header Indication is not set ME TA converts the entered text into the GSM 7 bit default alphabet accord
116. r all other parameters refer to 27 005 3 1 Parameter Definitions 2 5 4 CDS Received status report SR indication Receive a CDS if text mode CMGF 1 CDS lt fo gt lt mr gt lt ra gt lt tora gt lt scts gt lt dt gt lt st gt if PDU mode CMGF 0 CDS lt length gt lt CR gt lt LF gt lt pdu gt Parameters For all other parameters refer to 27 005 3 1 Parameter Definitions wavecom o 2009 Page 24 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Clarification When CSMS lt service gt is set to O all received SR are automatically acknowledged before CDS is sent to TE When CSMS lt service gt is set to 1 SR has to be acknowledged to network thanks to CNMA commands Depending of lt mode gt lt mt gt and channel status available or reserved URC can not or should not be sent to TE In these cases SR can be automatically acknowledged or rejected without waiting CNMA command 2 6 CMS ERROR Message Service Failure Result code 303 305 310 CU SIM not inserted pia USI busy sigs SIM PUK2 required 340 wavecom o 2009 Page 25 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_00
117. r ou 73 SM cause See 24 008 3 2 8 CRC Cellular result codes Select service CR mode CRC lt mode gt S O CRC lt mode gt Get supported modes CRC list of supported lt mode gt s Parameters e Disables extended format Enables extended format 3 2 9 CVHU Voice Hang up Control Select service voice CVHU lt mode gt hang up mode Get supported modes CVHU CVHU list of supported lt mode gt s Parameters lo stop DTR ignored but OK response given ATH disconnects MH Drop DTR and ATH ignored but OK response given 2s Drop DTR behavior according to G amp D setting ATH disconnects wavecon o 2009 Page 38 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISM0O218 AT Command Manual Clarification If DTR signal is inactive if DTR is not a pulse then Drop DTR does not respond OK 3 3 Call control result code 3 3 1 CR Service reporting Send CR notification during CR lt serv gt data call connection Parameters lt serv gt Description 3 3 2 CRING Ring indication Extended format for incoming CRING lt type gt call notification Parameters ASYNC Asynchronous transparent SYNC Synchronous transparent Fax wavecom o 2009 Page 39 172 Th
118. r type Refer to TIA 578 A Value 9600 is always returned by read command because communication must begin at this speed Clarification Set command is sent to ME only when link is online data mode Hence set command is not implemented in AT command parser but in RLP FAX module 7 2 5 FRM Facsimile receive Set mode si mode FRM FRM lt mode gt a OO wavecom o 2009 Page 138 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business WISMO218 AT Command Manual Get Get supported modes modes FRM 7 o o FRM 7 o o FRM list of FRM list of supported lt mode gt s lt mode gt s Parameters Integer type Refer to TIA 578 A Value 9600 is always returned by read command because communication must begin at this speed Clarification Set command is sent to ME only when link is online data mode Hence set command is not implemented in AT command parser but in RLP FAX module wavecom o 2009 Page 139 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 8 Proprietary AT commands 8 1 Capabilities identification and control
119. rching a new operator to register to 3 Registration denied S O Registration denied Registered roaming lt lac gt Description String type Two byte location area code in hexadecimal format e g OOC3 equals 195 in decimal String type Two byte cell ID in hexadecimal format 3 4 3 COPS Operator Selection Select COPS lt mode gt lt format gt lt oper gt lt CME ERROR lt err gt operator AcT gt Get current COPS COPS mode and lt mode gt lt format gt operator lt oper gt lt AcT gt CME ERROR lt err gt wavecom o 2009 Page 42 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ooo Smart wireless Smart business COPS list of supported lt stat gt long alphanumeric lt oper gt short alphanumeric lt oper gt numeric lt oper gt lt AcT gt s list of supported lt mode gt s list of supported lt format gt s CME ERROR lt err gt Parameters lo Automatic lt oper gt field is ignored po Manual lt oper gt field shall be present and lt AcT gt optionally set only lt format gt for read command COPS do not attempt registration deregistration lt oper gt and lt AcT gt fields are ignored this value is not applicable in read command response 4 Manual automatic lt oper gt field shall
120. ributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart business WISM0O218 AT Command Manual String type Operator in long alphanumeric format see COPS 3 5 Network service related result codes 3 5 1 CREG Network registration Network registration status CREG lt stat gt lt lac gt lt ci gt change event Parameters Refer to CREG command description 3 5 2 CLIP Calling Line Identification Presentation Calling Line Identification CLIP lt number gt lt type gt Presentation lt subaddr gt lt satype gt lt alpha gt lt CLI validity gt Parameters lt number gt Description Integer type Type of address String type subaddress of format specified by lt satype gt Integer type Type of subaddress wavecom o 2009 Page 59 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom pna Smart wireless Smart business WISMO218 AT Command Manual String type Alphanumeric representation of lt number gt corresponding to the entry found in phonebook used character set should be the one selected with CSCS CLI has been withheld by the originator CLI is not available due to interworking problems or limitations of originating network 3 5 3 COLP Connected line i
121. rrent format CSCA CSCA lt sca gt lt tosca gt Get supported CSCA formats Parameters lt sca gt Description String type SC address Address Value lt tosca gt Description Integer type SC address Type of Address Clarification This command read and writes the service center address in EF SMSP U SIM file If the SCA is not readable or empty read command returns an empty string At switch on the SCA is read on U SIM to have a default SCA for send and write command in text mode In PDU mode SCA can be provided in PDU Service Center Address is reset on switch on and is read on SIM on first PC connection after switch on See data stored by CSAS for default values 2 2 2 CSCB Select Cell Broadcast Messages Types Select CBM CSCB lt mode gt lt mids gt lt dcss gt types wavecom o 2009 Page 9 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Get current CSCB CSCB values lt mode gt lt mids gt lt dcss gt Get supported CSCB CSCB list of supported modes lt mode gt s Parameters o sss Message types Message types specified in lt mids gt and lt dcss gt are accepted in lt mids gt and lt dcss gt are accepted Message types specified in lt mids gt and
122. s 7 Set the selected GPIO Request the status of the selected GPIO waveconm o 2009 Page 160 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Note GPIO configuration is not stored in memory The current configuration is lost with a reset Be aware that this command doesn t change the reset state of the GPIO 8 6 10 WIMGPIOCFG GPIO configuration Set GPIO WMGPIOCFG lt I0 gt lt dir gt lt pull OK configuration mode gt Get GPIO WMGPIOCFG WMGPIOCFG configuration lt lO gt lt dir gt lt pull mode gt WMGPIOCFG lt lO gt lt dir gt lt pull mode gt zaa OK Get supported WMGPIOCFG WMGPIOCFG list of GPIO supported lt IO gt s list of configuration supported lt dir gt s list of supported lt pull mode gt s OK Description This command allows setting a GPIO as input or output Parameters 1 wavecom o 2009 Page 161 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 waevecom Smart wireless Smart business Note The GPIO configuration is not stored in memory The current configuration is lost with a reset If GPIO set
123. scr gt Description Battery charge level O 5 signal Signal quality 0 5 service Service availability O 1 Message received 0 1 call Call in progress 0 1 Roaming indicator 0 1 smsfull A short message memory storage in the MT has become full 1 or memory locations are available O wavecom o 2009 Page 69 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Restriction It is impossible to set indicator controls 3 6 8 CMER Mobile Termination event reporting ontrol URC CMER lt mode gt lt keyp gt lt disp gt lt CME ERROR lt err gt notifications ind gt lt bfr gt CMER lt mode gt lt keyp gt lt disp gt lt ind gt lt bfr gt CMER list of supported lt mode gt s list of supported lt keyp gt s list of supported lt disp gt s list of supported lt ind gt s list of supported lt bfr gt s Parameters Buffer unsolicited result codes in the TA if TA result code buffer is full codes can be buffered in some other place or the oldest ones can be discarded Discard unsolicited result codes when TA TE link is reserved e g in on line data mode otherwise forward them directly to the TE omitted Use previous value eC No k
124. secondtext gt wavecom o 2009 Page 74 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Integer type Value indicating the maximum length of field lt email gt String type Refer to 27 007 Clarification Only first lt group gt lt adnumber gt lt adtype gt lt secondtext gt lt email gt are returned with the command Some proprietary commands are implemented to fully manage 3G phonebook 3 6 11 CPBF Find phonebook entries Find entries CPBF lt findtext gt CPBF lt index1 gt lt number gt lt type gt lt text gt lt hidden gt lt group gt lt adnumber gt lt adtype gt lt secondtext gt lt email gt lt CR gt lt LF gt CPBF lt index2 gt lt number gt lt type gt lt text gt lt hidden gt lt group gt lt adnumber gt lt adtype gt lt secondtext gt lt email gt CME ERROR lt err gt Get location CPBF lt nlength gt lt tlength gt ranges lt glength gt lt slength gt lt elength gt CME ERROR lt err gt Parameters String type Field of maximum length lt tlength gt Character set as specified by CSCS For other parameters refer to CPBR command Clarification Only first lt group gt lt adnumber gt lt adtyp
125. sion Revision identification sssi lt isSSSsCsisidY 3 1 4 CGSN Request product serial number identification Read SN CGSN lt sn gt CME ERROR lt err gt Test if command is CGSN supported Parameters lt sn gt Description String type International mobile equipment identity IMEI 3 1 5 CSCS Select TE character set Set charset charset CSCS lt chset gt lt chset gt CSCS a lt chset gt Get supported values CSCS CSCS list of supported lt chset gt s Parameters Gsm GSM 7 bit default alphabet 3GPP TS 23 038 UCS2 16 bit universal multiple octet coded character set ISO IEC 10646 UCS2 character strings are converted to hexadecimal numbers from OOOO to FFFF e g 004100620063 equals three 16 bit characters with decimal values 65 98 and International reference alphabet ITU T T 50 wavecom o 2009 Page 28 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 3 1 6 CIMI Request international mobile subscriber identity Read IMSI CIMII lt IMSI gt CME ERROR lt err gt Test if command is CIMI supported Parameters String type without double quotes IMSI 3 1 7 CMUX Multiplexing mode CMUX lt mode gt lt subset gt lt port_s
126. t lt Line Id gt lt CauseSelect gt lt Cause gt lt Bearer gt The optional fields of the URC are filled only when information is available i e depending of the state of the call otherwise they are left empty Call notification PSCN lt Call Id gt lt Notification gt The optional fields of the URC are filled only when information is available otherwise they are left empty Parameters eo Disable presentation all notifications Enable presentation of PSCSC Enable presentation of PSCSC and PSCN o Cat Id not yet assigned alerting MT call 1 7 JCal Id representing a CS speech call gt 8 JCal Id representing a CS data call MO call SETUP no control by SIM MO call SETUP WITH CONTROL BY SIM accepted 2 MO call SETUP ERROR control by SIM rejected or other problem MO call PROCEED MO call ALERT at distant wavecom o 2009 Page 164 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ates Smart wireless Smart business WISM0O218 AT Command Manual MO call CONNECT with distant MT call SETUP ACCEPTED Bearer capabilities accepted by the ME MT call SETUP REJECTED Bearer capabilities rejected by the ME 30 MO call SETUP Call initiated by SAT SET UP CALL command received 31 MO call PROCEED Call initiated by SAT SET UP C
127. t CME ERROR lt err gt lt text gt lt recurr gt lt silent gt CALA lt time gt lt n1 gt lt recurr gt lt CR gt lt LF gt CALA lt time gt lt n2 gt lt recurr gt CME ERROR lt err gt CALA list of supported lt n gt s lt tlength gt lt rlength gt list of supported lt silent gt s CME ERROR lt err gt Parameters 07 04 11 11 34 25 internal clock Cf CCLK string type hh mm ss if lt recurr gt is present or yvyy mm dd hh mm ss if not lt n gt lt n1 gt lt n2 gt Description index of the alarm range 1 to 5 for now wavecom o 2009 Page 86 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual lt recurr gt Description string type value indicating day of week for the alarm in one of the following formats lt 1 7 gt lt 1 7 gt L Sets a recurrent alarm for one or more days in the week The digits 1 to 7 corresponds to the days in the week Monday 1 Sunday 7 Example The string 1 2 3 4 5 may be used to set an alarm for all weekdays O Sets a recurrent alarm for all days in the week Clarification Set command sets an alarm time in the MT If setting fails in an MT error CME ERROR lt err gt is retur
128. t LF gt lt pdu gt otherwise CMS ERROR lt err gt Get supported CMGL CMGL list of supported lt stat gt s values Parameters O Received unread message i e new message REC UNREAD 1 Received read message REC READ 2 Stored unsent message STO UNSENT 3 Stored sent message STO SENT wavecom o 2009 Page 17 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISMO218 AT Command Manual 4 All messages ALL For all other parameters refer to 27 005 83 1 Parameter Definitions Other parameters are extracted from memory storage Clarification Only SMS SUBMIT and or SMS DELIVER can be read SMS COMMAND are not supported CBM are not stored in ME TA memory CBM are not saved in SIM 2 3 4 CNIGR Read Message Read a CMGR lt index gt if text mode CMGF 1 command successful and SMS message DELIVER CMGR lt stat gt lt oa gt lt alpha gt lt scts gt lt tooa gt lt fo gt lt pid gt lt dcs gt lt sca gt lt tosca gt lt length gt lt CR gt lt LF gt lt data gt if text mode CMGF 1 command successful and SMS SUBMIT CMGR lt stat gt lt da gt lt alpha gt lt toda gt lt fo gt lt pid gt lt dcs gt lt vp gt lt sca gt lt tosca gt lt length gt lt CR gt lt L
129. t is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom Smart wireless Smart business lt number gt Description String type Phone number of format lt type gt Integer type Type of address refer GSM 04 08 8 subclause 10 5 4 7 default 145 when dialling string includes international access code character otherwise 129 String type Field of maximum length lt tlength gt Character set as specified by CSCS Integer type Value indicating the maximum length of field lt number gt Integer type Value indicating the maximum length of field lt text gt 8 5 5 PSCSP Customer Service Profile PSCSP Read CSP PSCSP PSCSP lt Service Groupe code x gt lt status gt lt CR gt lt LF gt PSCSP lt Service Groupe code y gt lt status gt CME ERROR lt err gt wavecom o 2009 Page 150 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Get supported values PSCSP PSCSP list of Supported lt Service Groupe code gt Description Command used to read the CSP file in SIM Set command has no effect OK returned Parameters lt service group Description code gt
130. t nlength gt ranges lt tlength gt lt glength gt lt slength gt lt elength gt CME ERROR lt err gt Parameters lt indexn gt Description Integer type Values in the range of location numbers of phonebook memory lt number gt Description String type Phone number of format lt type gt Integer type Type of address String type Field of maximum length lt tlength gt Character set as specified by CSCS lo Phonebook entry not hidden Phonebook entry hidden wavecon o 2009 Page 73 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom SEOS Smart wireless Smart business WISMO218 AT Command Manual String type Field of maximum length lt glength gt Character set as specified by CSCS String type Field of maximum length lt slength gt Character set as specified by CSCS Integer type Type of address String type Field of maximum length lt slength gt Character set as specified by CSCS String type Field of maximum length lt elength gt Character set as specified by CSCS Integer type Value indicating the maximum length of field lt number gt Integer type Value indicating the maximum length of field lt text gt Integer type Value indicating the maximum length of field lt group gt Integer type Value indicating the maximum length of field lt
131. ters o Sae SM service settings in profile O Hs Save SM service settings in profile 1 Clarification Parameter stored by CSAS Parameter name Length Default Non volatile memory filed value mA he one o avenprScasaress besa aoas hoos ee CSM lt vp gt 1 byte 0x00 v_hee_SmsvVp s_RelTime v_NbMinutes lt vp gt 1 byte 0x18 v_hee_SmsVp s_RelTime v_NbHours lt vp gt 1 byte 0x00 v_hee_SmsVp s_RelTime v_NbWeeks lt vp gt 20 bytes Ox00 0x00 v_ hee _SmsVp s_ RelTime v_Gap_RelativeTime ESMP CSCA CSCA CSMP CSMP CSMP CSMP CSMP lt vp gt 1 byte 0x00 v_hee_SmsvVp s_RelTime v_NbDays wavecom o 2009 Page 12 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wevecom a Smart wireless Smart business WISM0O218 AT Command Manual 2 2 6 CRES Restore Settings Restore SM service CRES lt profile gt CMS ERROR lt err gt settings Get the list of available CRES CRES list of supported profiles lt profile gt s Parameters los Restore SM service settings from profile O eo Restore SM service settings from profile 1 2 3 Message receiving and reading commands 2 3 1 CNMI New Messages Indication to TE Select CNMI lt mode gt lt mt gt lt bm gt lt CMS ERROR lt err gt procedure for ds gt lt bfr gt r
132. ther AT commands 3 6 4 CPWC Power class corresponding band Get the list of CPWC current and lt curr_class1 gt lt def_class1 gt lt band1 gt default power lt curr_class2 gt lt def_class2 gt lt band2 gt class for each supported CME ERROR lt err gt CPWC list of supported lt band gt list of lt class gt s pairs CME ERROR lt err gt Parameters lt class gt Description lt curr_classn gt s lt def_classn gt s Integer type O default not applicable to lt curr_class gt s or lt def_classn gt s 1 MT output power class as in GSM 45 005 38 lt class gt Description lt bandn gt s Integer type Frequency band one of the following O GSM900 1 GSM1800 2 GSM1900 3 GSM 400 3 6 5 CSO Signal Quality Get signal information CSQ CSQ lt rssi gt lt ber gt CME ERROR lt err gt wavecomn o 2009 Page 67 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ae Smart wireless Smart business WISM0O218 AT Command Manual Get supported values CSQ CSOQ list of Supported lt rssi gt s list of supported lt ber gt s Parameters lt rssi gt Description gs _ften 113 dBm or less to 51 dBm or greater l99 Not known or not detectable nn RXQUAL values in the table in TS 45 008 20 subclause 8 2 4 mc Not know
133. tion group store message are routed directly to the TE using unsolicited result code CMT Class 3 SMS DELIVERs are routed directly to TE using unsolicited result codes defined in lt mt gt 2 Messages of other data coding schemes result in indication as defined in lt mt gt 1 No CBM indications are routed to the TE 2 New CBMs are routed directly to the TE using unsolicited result code CBM o No SMS STATUS REPORTSs are routed to the TE 1 SMS STATUS REPORTs are routed to the TE using unsolicited result code CDS TA buffer of unsolicited result codes defined within this command is flushed to the TE when lt mode gt 1 3 is entered OK response shall be given before flushing the codes 1 TA buffer of unsolicited result codes defined within this command is cleared when lt mode gt 1 3 is entered wavecom o 2009 Page 14 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Clarification TA result code buffer is in volatile memory Messages may get lost if the power of ME TA is switched off before codes are sent to TE Thus it is not recommended to use direct message routing lt mt gt 2 or 3 lt bm gt 2 or 3 or lt ds gt 1 with lt mode gt value O or 2 When CSMS lt service gt is set to O all received
134. tions by MS are possible when during setup phase two bearer capability list have been negotiated one speech the other multimedia ATH without parameter is used to modify the call from multimedia to speech upgrade of service OK will be sent is modification succeeds ATH will not disconnect the multimedia call CHUP command has to be used If ATH is received and a video telephony call is currently in speech mode ERROR is returned In case of in call modification initiated by network ATH is used to reject the modification colon is not present multimedia mode will be requested first multimedia preferred 4 1 5 L Monitor speaker loudness wavecom o 2009 Page 110 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Parameters lt volume gt Description E Clarification This command is supported for compatibility purpose and has no effect on ME simple response OK 4 1 6 M Monitor speaker mode Setmode Memoari ee Parameters o 9 si mode E Clarification This command is supported for compatibility purpose and has no effect on ME simple response OK 4 1 7 O Online ISwitch to online mode to online mode lOol lt type gt O Parameters O Return to online data state from online comman
135. tributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual PDP Context Identifier PDP Context Identifier Clarification If lt cid gt is not Supported or is Supported but omitted ERROR will be returned If lt cid gt correspond to an already active PDP context activated with CGACT command ERROR will be returned the PDP must be in quiescent state before ATD 9x 3 10 13 Request Packet Domain IP service D Command Possible Response s Request packet domain D 98 lt cid gt CONNECT IPservice Parameters PDP Context Identifier PDP Context Identifier Clarification If lt cid gt is not Supported or is Supported but omitted ERROR will be returned If lt cid gt correspond to an already active PDP context activated with CGACT command ERROR will be returned the PDP must be in quiescent state before ATD 9x 3 10 14 CGEREP Packet Domain event reporting Set CGEV XXX CGEREP lt mode gt lt bfr gt notifications mode Get current settings CGEREP CGEREP lt mode gt lt bfr gt Get supported CGEREP CGEREP list of supported values lt mode gt s list of supported lt bfr gt s waveconm o 2009 Page 104 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W2
136. tting format of lt command gt and lt response gt is always hexadecimal AT CSCS HEX is not supported wavecon o 2009 Page 77 172 This document is the sole and exclusive property of WAVECOMI Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual 3 6 15 CRSM Restricted SIM access lt sw1 gt lt sw2 gt lt response gt CME ERROR lt err gt 176 Read a transparent EF READ BINARY Transparent file greater than 256 bytes are not supported gt P1 shall always be O ERROR otherwise gt P2 shall be in the range 0 256 178 Read a record READ RECORD Only P2 04 absolute mode is supported Other modes seems not to be useful 192 Get response GET RESPONSE If lt fileid gt is not provided the command applies to the last selected file 214 Read a transparent EF UPDATE BINARY Only P1 00 and P2 00 is supported Update a record Only P2 03 previous mode is allowed for updates on cyclic file refer to 51 011 For linear files SAP only supports mode P2 04 absolute 242 Status STATUS If lt fileid gt is not provided the command applies to the last selected file ATP must memorise Fileld of the last command 3FOO at the initialization of ATP by default Moreover v_LengthPattern O Integer type Identifier of a elementary datafile on SIM Mandatory
137. ue Multimedia call with fallback to speech 131 Proprietary value Multimedia call with fallback and service change allowed for UDI RDI call only Clarification CMOD command is used to select multimedia call mode for further D Dial command Proprietary values are defined to select multimedia call mode CMOD is reset to O when call is successfully connected if a set up error occurs or when the call is disconnected to avoid request of video telephony call accidentally 3 2 3 CHUP Hang up call Command Possible Response s Hang up calls CHUP Test if command is CHUP supported waveconm o 2009 Page 32 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISM0O218 AT Command Manual Clarification CHUP command gives an assured procedure to disconnect the call Refer to H command description Since only single mode is supported the execution of the command always disconnects active call 3 2 4 CBST Select bearer service type Select bearer GBST I lt specd gt L lt neme gt icces SSCS Get current CBST CBST bearer lt speed gt lt name gt lt ce gt CBST list of Supported lt speed gt s list of supported lt name gt s list of Supported lt ce gt s Parameters Autobauding automatic selection of the spee
138. ued during switch off of MS 8 3 2 PSSSURC Supplementary Services notification Set mode PSSSURC lt mode gt IGet current mode _ PSSSURC PSSSURC lt mode gt Get supported modes PSSSURC PSSSURC list of supported lt mode gt s Description This command is to configure the AT interface to give additional information through result code to TE when D command is entered with a SS string as parameter When lt mode gt parameter is enabled one or several intermediate result code are sent to provide additional information on SS operation Result code PSSSURC lt SsCode gt lt BasicServiceCode gt lt SsStatus gt lt no_reply_cond_timer gt lt ccbs_ index gt lt phone_ number _ton_npi gt lt phone_number _config gt lt phone_number gt lt sub address type gt lt sub_address authority_and_format_identifie gt lt sub address data gt lt clir_option gt PSSSERR lt cause_select gt lt cause gt One intermediate result code per lt service code gt is sent wavecom o 2009 Page 141 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom a Smart wireless Smart business WISMO218 AT Command Manual Parameters Ce ee Disable sending of additional result code ssid of additional result code Heo Enable sending of additional result code Clarification
139. ule uses unsolicited code once after the boot process PPSUP lt stat gt The PPSUP notification will not be sent if the module is in autobaud mode and nobytes have been received from TE to adapt the serial link to the actual speed If the command fails in an MT error CME ERROR lt err gt is returned Test command returns supported array index values wavecom o 2009 Page 155 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 8 6 4 PSCHRU Channel registration URC Set URC filter PSCHRU lt mask gt Get current channel PSCHRU PSCHRU lt mask gt filter Get supported masks PSCHRU PSCHRU list of supported lt mask gt s Description Set command is used to filter one or several type of URC on a channel By default all URC types are enabled on a newly opened channel This command only applies on the channel it is submitted other channels are not impacted Depending of lt mask gt value URC will or will not be broadcasted on the channel Parameters No URC sent on the channel Call related URC to be sent on the channel RING CRING CCCM CCWV CCWA CLIP COLP CSSI CSSU PSCALL PSDCI PSCSC PSCN PSVTCS SMS related URC to be sent on the channel CDS CMT CMTI PSMWI CBM
140. us gt lt class1 Sa lt status gt lt class2 gt Get current CCWA CCWA lt n gt mode CCFC list of supported lt reason gt s Parameters eo 4 Disable presentation of CCWA Enable presentation of CCWA jo iewable SSCS wavecom o 2009 Page 50 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ss Smart wireless Smart business WISM0O218 AT Command Manual lt class gt Description 2 data refers to all bearer services with lt mode gt 2 this may refer only to some bearer service if TA does not support values 16 32 64 and 128 Fax facsimile services 7 14 24 4 Default oO Notactive S 3 4 11 CHLD Call related supplementary services Control call related CHLD lt n gt CME ERROR lt err gt services Get supported values CHLD CHLD list of supported lt n gt s Parameters Description Releases all held calls or sets User Determined User Busy UDUB for a waiting call Releases all active calls if any exist and accepts the other held or waiting call Releases a specific active call x Places all active calls if any exist on hold and accepts the other held or waiting call Places all active calls on hold except call X with which communication shall be supported Adds a held call to the conversation
141. uted or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom os ates Smart wireless Smart business WISM0O218 AT Command Manual Parameters lt num gt Description 0 255 Counts the number of rings detected on the line It is cleared if a ring is not detected over an eight second time period If the register value equals the value contained in SO the modem will answer the phone Value stored in non volatile memory by amp W command 5 1 4 S2 Escape character Parameters lt esc gt Description 43 Escape character 43 i e 0 character 43 i e 5 1 5 S11 DTMF Dialling Speed Set DTMF dialling S11 lt time gt speed Parameters lo 999 sd 999 DTMF IDTMFdiallingspeed ss isi sSSSSSSCidY speed Clarification This command is supported for compatibility purpose and has no effect on ME simple response OK 5 1 6 S95 Windows XP compatibility Windows XP S95 lt time gt compatibility wavecom o 2009 Page 128 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual Parameters lo g99 si 999 Windows XP Windows XP compatibility sssi lt iSsSSCsidY Clarification This command is supported for compatibility purpose and has
142. uted or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 3 6 26 CRIVIP Ring Melody Playback Play ring melody CRMP lt call CME ERROR lt err gt type gt lt volume gt lt type gt lt index gt CRMP list of Supported lt call type gt s list of supported lt volume gt s lt typeO gt list of supported lt index gt s lt CR gt lt LF gt CRMP list of Supported lt call type gt s list of supported lt volume gt s lt type1 gt list of supported lt index gt s CME ERROR lt err gt Parameters los Manufacturer specific lt volume gt Description eC Manufacturer defined 1s Correspond to vibrator mode Clarification If a melody is played it s just played for 10 sec then stopped wavecom o 2009 Page 85 172 This document is the sole and exclusive property of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom ee Smart wireless Smart business WISM0O218 AT Command Manual 3 6 27 CLAC List all available AT commands List all commands CLAC lt AT Command1 gt lt CR gt lt LF gt lt AT Command2 gt CME ERROR lt err gt Test if command CLAC CME ERROR lt err gt is Supported 3 6 28 CALA Set alarm time CALA lt time gt lt n gt lt type g
143. written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wevecom Z Smart wireless Smart business WISMO218 AT Command Manual Get supported lines PSALS PSALS list of supported lt lineid gt Description Set command is used to select the line to be used for MO speech calls For MT speech calls CRING URC refer CRC command indicates on which line the call is receive CR ING VOICE gt default case line 1 CRING VOICE AUX gt line 2 1 Line 1 Default Line 2 Auxiliary line 8 5 3 PSDCIN Diverted Call Indicator Notification PSDCIN lt mode gt PSDCIN lt Line Id gt lt status gt lt Line Id gt L lt CR gt lt LF gt PSDCIN lt Line Id gt lt status gt CME ERROR lt err gt Get current mode PSDCIN PSCDIN lt mode gt CME ERROR lt err gt Get supported values PSDCIN PSDCIN list of Supported lt modes gt list of supported lt line gt s Description Set command enables disables the presentation of a Diverted Call Indication also know as CFU result code from ME to TE When lt mode gt 2 status of lt lind Id gt is requested If lt Line Id gt is not provided query is requested for all lines When lt mode gt 1 Diverted Call Indication PSDCI is sent to TE on reception of network notification Several result code can been sent at the same time on reception of the notification Diverted Diverted Call Indication In
144. y of WAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_003 001 April 24 2009 wavecom oo ates Smart wireless Smart business WISM0O218 AT Command Manual 3 4 14 CAOC Advice of Charge Control AOC CAOC lt mode gt CAOC lt ccm gt notification CME ERROR lt err gt Get current mode __ CAOG CAOC lt mode gt Get supported values CAOC CAOC list of Supported lt mode gt s Parameters los query query CCM value sss i ssSSSSsSsSCi i value ao Deactivate the unsolicited reporting of CCM value 2 ss Acctivate the unsolicited reporting of CCM value String type Three bytes of the current call meter value in hexadecimal format e g 00001E indicates decimal value 30 value is in home units and bytes are similarly coded as ACMmax value in the SIM card or in the active application in the UICC GSM or USIM 3 4 15 CSSN Supplementary service notifications SS notification control CSSN lt n gt lt m gt CSSN lt lt n gt lt m gt Get supported values CSSN A list of supported lt n gt s list of supported lt m gt s Parameters ee O O default Disable Disable presentation of CSSI 2 of CSSI aoo Enable presentation of CSSI wavecom o 2009 Page 54 172 This document is the sole and exclusive property of WWAVECOM Not to be distributed or divulged without prior written agreement WA_DEV_W218_UGD_0

Download Pdf Manuals

image

Related Search

Related Contents

  K - Esp@don    Sub-Zero SRT484CG User's Manual  Samsung GT-E2330 Priručnik za korisnike  MC Concept - clearaudio electronic  Zebra 105912-024  AGA Premium series User manual  M340 Enlace Serie    

Copyright © All rights reserved.
Failed to retrieve file