150W Moving Head HAND MANUAL
Contents
1. DMX channel Function Data Description color wheel 0 295 rotation slow gt fast gobo wheel 0 255 rotation slow gt fast j gobo wheel 0 255 gobo angle 0 360 rotation SHUT and Dimmer 0 255 pan 0 255 pan adjustment 0 540 tilt 0 255 Tilt adjustment 0 270 i Pan Tilt speed 0 255 Fast slow Reset 0 255 The Control Board on the front side of the base allow you to assign the DMX fixture the address which is defined as the first channel from which the light will respond to the contrllor If you set for example the address to channel 5 the light will use the channel 5 to 22 for control Please be sure that you don t have any overlapping channels in order to control each the light correctly and independently from any other fixture on the DMX data link Power supply EU model 208 230 240V AC 50 60HZ Fuse T5A 250V US model 100 115 208 230V AC 50 60HZ Fuse T5A Power consumption 250W TEMPERATURES Maximum ambient temperature 40 C Maximum housing temperature steady state 80 C Dimensions and weight Length of base including handles 450mm Width of yoke 405mm Height head horizontal 540mm Weight net2. net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the fixture staying in the area below the installation place on bridges under high working pluses and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operator for the first time and after changes before taking into operation anther time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating installations are approved by a skilled person once a year PROCEDURE The projector should be installed outside areas where persons may walk by or be seated IMPORTANT Overhead rigging requires extensive experience including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and Or damage to property The projector has to be installed out of the reach of people If the projector shall be l
3. dimmer unit allowing very smooth dimming and strobe effect 1 10 flash s Addressing special functions setting effects calibration via control panel with 4 digitLED display Pan movement rang 530 Tilt movement rang 280 6 high quality stepper motors for smooth movement Self resetable thermo fuse For PHILIPS MSD 150W or OSRAM MSD 150 lamp CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wire This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to drastic temperature fluctuation e g after transportation This device falls under protection class 1 The power plug must only be plugged into protection class 1 outlet Never let the power cord come into contact with other cables Handle the power cord all connections with the mains with particular caution Make sure that the available voltage is not higher than stated on the rear panel Make sure that the power cord is never crimped or
4. in order to avoid hazards Should you have further questions please contact your dealer We hope you will enjoy the light we can assure you that you will enjoy this device for years if you follow the instructions given in this manual
5. 15kg Shipping weight 18kg The operator has to make sure that safety relating and machine technical installations are inspected by an export after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the devices have to be tightly connected and must not be corroded 2 There must not be any deformations on housing fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts like axles eyes and others must not show any traces of wearing e g material abrading or damages and must not rerate with unbalances 4 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed DANGER TO LIFE Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents CAUTION The lens has to be replaced when it is obviously damaged so that its fu
6. C lt 150W Moving Head HAND MANUAL WWW CKLIGHT COM CN CATALOGUE Introduction Features Description of the fixture Safety instructions The safety guides The operation limits Installation Fitting Exchanging the lamp Beam path Inserting Exchange the gobos Rigging DMX512 connection connection between fixtures DMX control channels Display and operating instructions DMX 8channels instruction Address code Control Technique parameter Power supply Lamp Color wheel Fix the gobo wheel Rotating gobo wheel Shutter Dimmer shutter strobe Fans Motors Maintenance and cleaning CAUTION Keep this device away from rain and moistture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initial start up Thank you for having chosen our MOVING HEAD You acquired a versatile powerful and intelligent lighting effect Unpack your MOVING HEAD and make sure that there are no damages caused by transportation Should there be any please consult your local dealer and do not take the device into operation Multi function MOVING HEAD spot Color system 1 color wheel Color wheel has 7 kinds of different color dichroic filters white Gobo wheel have 7 rotating metal gobos The rotating gobos can be turn by 360 Combined shutter
7. damaged by sharp edges Check the device and the power cord by the plug Never pull out the plug by tugging the power cord Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective COUTION During the operation the housing becomes very hot Frequent open cut the lighting will reduce the life of the lamp Never look directly into the light source as sensitive persons may suffer an epileptic shock especially meat for epileptics Damages caused by non observance are not subject to warranty Keep away children and amateurs OPERATING DETERMINATIONS This device is a moving head spot for creating decorative effects And was designed for indoor use only This device is designed for professional use Such as on stages in disco in theater Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device Do not operate the device without lamp Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles W
8. hen choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be cables lying around You own and the safety of others Always fix the fixture with an appropriate safety rope Fix the safety rope at the correct holes only Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened The lamp must never be ignited if the objective lens or any housing cover is open as discharge lamps may expose and emit a high ultraviolet which may cause burms The maximum ambient temperature must never be exceeded CAUTION The lens has to be replaced when it is obviously damaged so that its function is impaired dug to cracks or deep scratches 0perate the device only after having familiarized with its functions Do not operation by persons not qualified for operating the device Most damages are the result of unprofessional operation CAUTION The lamp has to be replaced when it is damaged or deformed due to the heat Please use the original packing if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons Never remove the serial barcode from the device as this would make the guarantee void If this device will be operate in any way different to the one described in this manmal the product may suffer damages and the guarantee becomes void F
9. nction is repaire e g Due to cracks or deep scratches The objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly The gobos may be cleaned with a soft brsh The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The diachronic color filters the gobo wheel and the internal lenses should be cleaned monthly To ensure a proper function of the gobo wheel we recommend lubrication in six month intervals The quantity of oil must not be excessive in order to avoid that oil runs out when the gobo wheel rotates There are no serviceable parts inside the device except for the lamp and the fuse Maintenance and service operations are only to be carried out by authorized dealers Replacing the fuse If the lamp burns out the fine wire fuse of the device might fuse too Only replace the fuse of same type and rating Before replacing the fuse unplug mains lead Procedure STEP 1 Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing anti clockwise STEP 2 Remove the old fuse from the fuse holder STEP 3 Install the new fuse in the fuse holder STEP 4 Replace the fuse holder Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged it has to be replaced by authorized dealers only
10. owered from the ceiling or high joists professional trussing systems have to be used The projector must never be fixed swinging freely in the room CAUTION Projectors may cause severe injuries when crashing down If you have doubted concerning the safety of a possible installation do NOT install the projector Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector s weight DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc Within a distance of min 0 5 m CAUTION Use 2 appropriate clamps to rig the fixture on the truss Follow the instructions mentioned at the bottom of the base Make sure that the device is fixed properly Ensure that the structure truss to which you are attaching the fixtures is secure The Moving Head can be placed directly on the floor or rigged in any orientation on a truss without altering its operation character rustics see the drawing There are tow possibility how to fix the MH 1200W on a trusses with the clam brackets part of delivery or mounting plate is not included in deliver only on demand Use the rigging clamps not included with screws M 10 or M12 For overhead use always install a safety rope that can hold at least 10 times the weight of the fixture You must only use safety ropes with screw on carbines Connection with the mains Connect the device to the mains with the po
11. urthermore any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash FITTING EXCHANGING THE LAMP DANGER Install the lamp with the device switched off only Unplug from mains before Open the small lamp cover by loosening the 3 Phillips screws if changing the lamp remove the old lamp from the socket Do not install a lamp with a higher wattage A lamp like this generates temperatures the device is not designed for Damages caused by non observance are not subject to warranty Please follow the lamp manufacturer s notes Do not touch the glass bud bare handed during the installation Make sure that the lamp is installed tightly into the lamp holder system Reclose the top cover of the head and tighten the Phillips screws Before sticking the lamp by pressing the UP and DOWN buttons in one time and then confirming with the Enter button RIGGING Danger to life Please consider the EN 60598 2 17 and the respective national norms drums during the installation The installation must only be carried out by an authorized dealer The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a safety attachmant an appropriate catch
12. wer plug The occupation of the connection cables is as follow Cable Pin International Brown Live L Blue Neutral N Yellow green Earth The earth has to be connected DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert DMX 512 connection connection between fixtures The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to controller with the fixture or one fixture with anther Occupation of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 2 Signal 3 Signal If you are using the recommended controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMxX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the frits fixture in them chain with the DMX input of the next fixture Ways connect one output with the input of the next fixture until all fixtures are connected CAUTION At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 ohm resistor between Signal and into a 3 pin XLR plug it in the DMX output of the last fixture DMX channel description
Download Pdf Manuals
Related Search