Home

RoboScan Pro 518

image

Contents

1. Description Pins Switched ON Random sequence wide pan tilt auto trigger 2 10 Random sequence wide pan tilt music trigger 1 2 10 Random sequence narrow pan tilt auto trigger 2 3 10 Random sequence narrow pan tilt music trigger 1 2 3 10 Lamp ON 8 10 Lamp OFF 7 10 Adjustment sequence for service use only 1 5 10 Adjustment sequence for service use only 1 2 5 10 L E D chase auto trig for service use only 4 10 L E D chase music trig for service use only 1 4 10 Controller Operation 10 Getting Started The RoboScan Pro 518 may be used with DMX 512 and Martin protocol controllers it automatically determines which protocol is used Protocol auto detection can be reactivated if necessary by switching on all ten DIP switches and then resetting the address 1 for Controller Operation on page 8 respond to the controller RoboScan Pro 518 Switch on and configure the controller Connect the RoboScan Pro 518 to the controller as described under Setup Apply power to the RoboScan After a short reset procedure it will The controllable effects are described below See your controller manual and the DMX pro tocol for additional information Lamp A relay inside the fixture allows you to turn on and off the lamp via the controller without affecting the rest of the fixture After switching on the RoboScan Pro 518 the lamp will remain off until you send a lamp on command f
2. Dimmer Shutter High resolution 0 to 100 smooth dimming is provided by the combined dimmer shutter system Use high speed dimming to open or close the dimmer instantly It s also possible to strobe at up to 9 flashes per second Effects Wheel The effects wheel has a frost filter a 3 facet prism for multiplying images and a 5500 to 3400K color temperature corrector CTC Combining the CTC with a color filter yields another shade of the color Fan Fan speed can be reduced for short periods if quieter operation is required Low fan speed reduces cooling ability and should only be used when absolutely necessary and only if the ambient temperature is 25 C 77 F or less If the temperature inside the fixture exceeds a certain level a built in thermostat will automatically power off the lamp You can turn off the lamp if the fan must be run at low speed for more than a few minutes Focus Focus may be adjusted manually by turning the lens barrel Operating with Martin Controllers 12 Beginning with software version 6 4 an improved speed array has been programmed for use with the Martin controllers This increases the range of speeds available for controlling effects To use this feature the DMX mode jumper must be set to mode 3 This is the fac tory default setting See DMX Mode Selection on page 14 if you need to change the mode setting RoboScan Pro 518 section 4 SERVICE AND MAINTENANCE IMPORTANT Read th
3. 0 3 meters 12 in away from the surface to be illuminated and at least 0 1 meters 4 in from any combus tible materials Verify that the clearance around the fan and air vents is at least 0 1 meters 4 in Verify that there are no flammable materials nearby Setup for Controller Operation Connect the Serial Link The RoboScan Pro 518 may be used with DMX and Martin protocol controllers The out puts on these controllers are different DMX controllers usually have 5 pin XLR outputs and are wired with pin 2 cold and pin 3 hot Martin standard controllers have 3 pin XLR outputs wired with pin 2 hot and pin 3 cold The Pro 518 s XLR input is config ured for the Martin standard When connecting a RoboScan Pro 518 to any DMX standard device you must swap the hot and cold signals with a phase reversing cable 1 Connect the controller s data output to the RoboScan Pro 518 s input If using a Martin standard controller use a direct 3 pin to 3 pin cable such as the one included If using a DMX controller use a phase reversing cable either 3 pin to 3 pin or 5 pin to 3 pin depending on the output of the controller Continue the link connect the output of the fixture closest to the control ler to the input of the next fixture Use a direct cable when connecting same standard fixtures Use a phase reversing cable only when connect ing a DMX standard fixture to a Martin fixture with pin 2 hot Up to 32 fix tures may be
4. The factory default is mode 3 The address may be any channel up to 504 within the controller s range 506 if 7 channels are used Example 4 Pro 518s using mode 3 can be addressed as follows O Au ed L9 CON ooo amo co r 69 gt O exeo oo TH AY OD SH LO COUP C0 Od a ef ef 7 7 eC CA CA QL CI CA CCT CI CO CO CO CO O19 CO CO Pro 518 No 1 Pro 518 No 2 Pro 518 No 3 Pro 518 No 4 Address 1 Address 10 Address 19 Address 28 Use the following procedure to set a Martin or DMX address 1 Select an available address within the controller s range Find the DIP switch setting in the address table on page 23 Set the DIP switch by flipping pins 1 through 9 ON or OFF as listed in the address table Flip pin 10 to OFF Installation 9 section 3 OPERATION Stand Alone Operation The Roboscan Pro 518 may be operated without a controller in stand alone mode In this mode the fixture performs a random sequence that is triggered by the beat of the music or at a set speed The DIP switch must be set to the desired stand alone mode before applying power 1 2 Stand Alone Modes With the fixture powered off set the DIP switch as shown below for the desired mode Pins not listed must be switched off Apply power to the RoboScan Pro 518 to run the sequence
5. fast gt slow 76 78 30 31 Gobo 2 static 79 102 31 40 Gobo 2 CW slow gt fast 103 126 40 49 Gobo 3 CCW fast gt slow 127 129 50 51 Gobo 3 static 130 153 51 60 Gobo 3 CW slow gt fast 154 177 60 69 Gobo 4 CCW fast gt slow 178 180 70 71 Gobo 4 static 181 204 71 80 Gobo 4 CW slow gt fast 205 228 80 89 Gobo 5 CCW fast gt slow 229 231 90 91 Gobo 5 static 232 255 91 100 Gobo 5 CW slow gt fast Effects Wheel 0 63 0 25 Open 5 64 127 25 50 5500 gt 3400K CTC filter 128 191 50 75 Frost 192 255 75 100 3 facet prism 6 Pan 0 255 0 100 Left gt Right 127 neutral 7 Pan Fine LSB 0 255 0 100 Left gt Right 127 neutral 7 7 8 Tilt 0 255 0 100 Up gt Down 127 neutral 7 i 9 Tilt Fine LSB 0 255 0 100 Up gt Down 127 neutral Pan Tilt Speed E 8 0 0 Tracking 1 251 0 98 Fast gt Slow 252 255 99 100 Blackout while moving Color Speed 0 0 Tracking 1 251 0 98 Fast gt Slow 3 9 252 255 99 100 Blackout while moving Dimmer Speed 0 251 0 98 Fast gt Slow 252 255 99 100 Fast 20 RoboScan Pro 518 appendix b SPECIFICATIONS Dimensions TSM Stl s 5 zsh anaa e a seat eds 533 mm 21 0 Height with bracket eei ee re teet ecrire des i 325 mm 12 8 Height without bracket essent 185 mm 7 3 Madthi sor RC URGE EUN ets eee 280 mm 11 0 BATA I EEEE E EAE A TA E AE EAA 14
6. figure 1 and move the GREY wire labelled V to either the 220 V 230 V or 250 V terminal to select the local AC voltage 3 Locate the transformer at the rear right corner of the unit and move the BROWN wire also labelled V to either the 225 V or 240 V terminal to select the local AC voltage 4 Reassemble the unit before connecting to AC power Service and Maintenance 15 Adjusting the Mirror 16 Readjusting the mechanical stop on the RoboScan Pro 518 mirror adaptor is required if the pan or tilt motor occasionally loses step leaving the mirror incorrectly positioned after a reset This error occurs when the recoil of the mechanical reset bounces the mirror and bracket a whole pan or tilt motor step Right view F1 Figure 2 Pan Adjustment 1 Connect the RoboScan Pro 518 to a controller and set the address Switch on the controller and then the fixture Use the controller to move the mirror to the extreme left position thus positioning screw A1 at the upper mechanical stop A2 Release the lock nut on adjustment screw A1 Turn screw A1 clockwise 1 2 1 turn to increase the distance between the head of the screw and the mechanical stop A2 Tighten the lock nut on screw A1 Reset the fixture a number of times to check the new reset position Use the controller to move the mirror through all extreme positions checking that adjustment screw B1 does not touch mechanical stop B2 during these ste
7. more of the screws 7 Ifthe light is significantly brighter in the center of the field than it is at the edge the lamp is too far forward in the reflector Pull the lamp in by turn ing all three screws clockwise 1 4 turn at a time until the light is evenly distributed Service and Maintenance 13 8 Ifthe light is brighter around the edge than it is in the center or if light output is low the lamp is too far back in the reflector Push the lamp out by turning the screws counter clockwise 1 4 turn at a time until the light is bright and evenly distributed DMX Mode Selection The DMX mode is set by a jumper inside the RoboScan Pro 518 The factory default is mode 3 jumper on pins 4 and 5 Follow the procedure below to enable modes 1 or 2 WARNING Make sure the fixture is disconnected from AC power before proceeding 1 Remove the 6 screws labelled D and C in figure 1 and carefully remove the complete pan tilt section Avoid unplugging the motor cables from the circuit board 2 Locate jumper PL432 on the circuit board refer to the nearby label To enable DMX mode 1 simply remove this jumper To enable DMX mode 2 move the jumper to pins 5 and 6 3 Reassemble the fixture before connecting to AC power A i C B to i B mm gt or Om ballast circuit board DMX jumper transformer Figure 1 14 RoboScan Pro 51
8. 01 To protect yourself and others from electric shock e Disconnect the fixture from AC power before removing or installing the lamp fuses or any part and when not in use Always ground earth the fixture electrically Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault protection Do not expose the fixture to rain or moisture Refer any service operation not described in this manual to a qualified technician To protect yourself and others from UV radiation and lamp explosion Never operate the fixture with missing or damaged lenses and or covers When replacing the lamp allow the fixture to cool for at least 5 minutes before open ing the fixture or removing the lamp Protect your hands and eyes with gloves and safety glasses Do not stare directly into the light Never look at an exposed lamp while it is lit Replace the lamp if it becomes defective or worn out 4 RoboScan Pro 518 To protect yourself and others from burns and fire Never attempt to bypass the thermostatic switch or fuses Always replace defective fuses with ones of the specified type and rating Keep all combustible materials for example fabric wood paper at least 0 1 meters 4 inches away from the fixture Keep flammable materials well away from the fixture Do not illuminate surfaces within 0 3 meters 12 inches of the fixture Provide a minimum clea
9. 1 04 1 21 53 85 117 149 181 1213 245 277 309 341 373 405 437 469 501 0 1 1 0 1 22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502 4 9043 19 1 23 55 87 119 151 183 1215 247 279 311 343 375 407 439 471 503 0 0 0 1 1 24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504 1 0 0 1 1 25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505 Oj a p 26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506 1 1 0 1 41 27 59 91 123 155 187 1219 251 283 315 347 379 411 443 475 507 0 0 1 1 1 28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508 4 0 4 29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509 o 1 1 1 1 30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510 1 1 14 14 1 31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511 DIP Switch Table 23
10. 5 011 1100 6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486 11111 01010 7 39 71 103 135 1167 199 231 263 295 327 359 391 423 455 487 a o 8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488 1 0 0 140 9 41 73 105 137 169 201 233 265 297 329 361 393 425 457 489 o 1 0 1 0 10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490 4 at O 4 0 11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491 010 1110 12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492 110111 110 13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493 0 a a i a o 14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494 1 1 1 140 15 47 79 111 1143 175 207 239 271 303 335 367 399 431 463 495 0 0 0 0 1 16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496 4 o0 p 0 rs 17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497 0o 1 0 0 1 18 50 82 1141146 178 210 242 274 306 338 370 402 434 466 498 1 110 0 1 19 51 83 1151147 179 211 243 275 307 339 371 403 435 467 499 p 3g 4 20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500 1 0
11. 8 Selecting Voltage and Frequency The voltage and frequency settings must match the local AC power supply Operating at the incorrect setting can result in poor light output shortened lamp life overheating and dam age to the fixture The settings are printed on the serial number label on the front of the case if the voltage is not within 5 percent of the local supply or the frequency 50 60 Hz is different then the ballast and transformer must be rewired Selectable Selectable Model Voltages Frequencies RoboScan Pro 518 EU 230 V 240 V 250 V 50 Hz RoboScan Pro 518 US 100 V 110 V 120 V 50 60 Hz WARNING Make sure the fixture is disconnected from AC power before pro ceeding RoboScan Pro 518 US 1 Unscrew the 8 screws labelled A and B in figure 1 that secure the casing over the lamp housing and remove the casing 2 Locate the ballast at the rear left corner see figure 1 and move the GREY wire labelled F to either the 50 Hz or the 60 Hz terminal to select the local frequency 3 Locate the transformer at the rear right corner of the unit and move the BROWN wire labelled V to either the 100 V 110 V or 120 V terminal to select the local AC voltage 4 Reassemble the unit before connecting to AC power RoboScan Pro 518 EU 1 Unscrew the 8 screws labelled A and B in figure 1 that secure the casing over the lamp housing and remove the casing 2 Locate the ballast at the rear left corner see
12. B1 and B2 Note It is strongly recommended that the pan tilt assembly be locked for transportation by replacing the thumbscrews in positions Al and A2 3 Carefully remove the protection foil and warning notice from the mirror Rigging 1 Secure the mounting bracket to the 3 bolts located on the top of the chassis with 3 M8 self locking nuts included 2 Verify that the clamp not included is undamaged and can bear at least 10 times the fixture s weight Bolt the clamp securely to the bracket with a grade 8 8 minimum M10 bolt and lock nut or as recommended by the clamp manufacturer through the 11 mm hole in the center of the mount ing bracket 3 f permanently installing the fixture verify that the hardware not included and mounting surface can bear at least 10 times the fixture s weight Installation 7 Verify that the structure can support at least 10 times the weight of all installed fixtures clamps cables auxiliary equipment etc Working from a stable platform clamp or fasten the fixture to the struc ture Install a safety cable that can hold at least 10 times the weight of the fix ture through over the support and mounting bracket Loosen the swivel locks and tilt the fixture to the desired angle Turn the swivel locks clockwise to tighten If a swivel lock does not tighten fully pull the handle out turn it counterclockwise and retighten Repeat as necessary Verify that the fixture is located at least
13. RoboScan Pro 518 user manual 1998 2000 Martin Professional A S Denmark All rights reserved No part of this manual may be reproduced in any form or by any means without permission in writing from Martin Professional A S Denmark Printed in Denmark P N 35000059 Rev D section 1 Introduction RoboScan Pro 518 Safety Information cccceeseesseeeeeeeeeeeeeeeeaeeseeeeeneeteaeeeneeeaas 4 Features e D rc 5 Accessorie S dde HR REED Bi rae pier ie vire ox c 5 section 2 Installation Installing and Changing the Lamp seen 6 Checking Voltage and Frequency Settings sse 6 Installing a Plug on the Power Cord eese 7 Releasing the Pan Tilt Lock 2 eeeseeeeeeeeeeeeneneenntnnee nennen 7 PRIQQING er C EM 7 Setup for Controller Operation ssseeeeeeeeeennen nennen 8 section 3 Operation Stand Alone Operation eeesssssssseeeseseene enne nnne nennen ren 10 Controller Operation 2 coire et prete i e iet hem hee ri gets 10 FOCUS c 12 Operating with Martin Controllers esseeseeeenneneneeneenn nnn 12 section 4 Service and Maintenance Adjusting the Larmp Rem ere ndi env eurs 13 DMX Mode Selection seeessssssssesseseeseennee nennen nnne nnne nere 14 Selecting Voltage and Frequency ssssssseeeeeeeneren
14. connected on a serial link Insert a male 120 Q XLR termination plug in the output of the last fixture on the link The termination plug is simply a 3 pin male XLR plug with a 120 Q resistor soldered between pins 2 and 3 The termination plug is required for error free communication Set the Address When using the RoboScan Pro 518 with a controller you must set the DIP switch to the start channel also known as the address which is the first channel the controller uses to send instructions to the RoboScan Pro 518 RoboScan Pro 518 3 pin to 3 pin 5 pin to 3 pin 3 pin to 5 pin Phase Reversing Phase Reversing Phase Reversing Cable Cable Cable Connections Connections Connections Male Female Male Female Male Female 1 1 1 1 1 1 2 2 2 2 2 2 25 5 amp 3 dc UR A 4 4 5 5 P N 11820006 P N 11820003 P N 11820002 For independent control each fixture must have its own address and control channels Two or more RoboScan Pro 518s may have the same address however they will receive the same instructions and behave identically Martin mode The RoboScan Pro 518 uses 1 channel to communicate with the controller The address may be any channel between 1 and 32 DMX mode The RoboScan Pro 518 may be operated in 3 DMX modes see the DMX pro tocol starting on page 18 for details It uses 7 consecutive DMX channels in mode 1 and 9 consecutive DMX channels in modes 2 and 3
15. e procedures carefully If you do not feel completely compe tent to perform the service consult qualified service personnel for assistance Adjusting the Lamp The RoboScan Pro 518 comes fully adjusted from the factory however readjustment of the lamp may be necessary due to differences between lamps The lamp is adjusted by turning the 3 Phillips head screws on the lamp access plate Turning these clockwise pulls the lamp back towards the rear and vice versa Keep adjustments small to avoid pulling the lamp so far off center that it hits the reflector WARNING The fixture must be cool and disconnected from AC power 1 Remove the 3 thumbscrews from the lamp access plate and remove the lamp assembly 2 Make a preliminary adjustment turn the adjustment screws so that the inside to inside measurement between the lamp socket mounting plate and the lamp access plate is 13 mm 1 2 in Replace the lamp assembly Flip DIP switch pins 8 and 10 on Flip all other pins off Apply power to the RoboScan Pro 518 After it has reset it produces a white light with an open gobo for adjustment purposes Wait approxi mately 5 minutes for the lamp to reach full brightness 5 Manually position the fixture and or mirror so the light shines on a flat surface and focus the beam 6 If there is an off center hot spot the lamp is not centered in the reflec tor Pull the hot spot into the center of the field with small adjustments of one or
16. hows DIP switch settings for channels 1 511 To find a setting locate the chan nel in the table Follow the row to the left to find the settings for pins 1 through 5 follow the column to the top to find the settings for pins 6 through 9 A 0 indicates the pin is turned off and a 1 indicates the pin is turned on Pin 10 is always switched OFF when setting a controller address Example The table shows the setting for channel 212 is 00101 for pins 1 5 and 0110 for pins 6 9 Pins 3 5 7 and 8 are set to on pins 1 2 4 6 9 and 10 are set to off DIP Switch Setting 381 0 0 0 0 0 0 0 0 1 1 1 1 1 1 141 41 388 0 0 0 0 1 1 1 1 0 0 0 0 1 1 141 41 0 OFF 7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 4 1 12 ON 3861 0 1 0 1 0 11 0 1 0 1 0 1 0 1 04 1 1 2 3 4 5 010 0100 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480 1 0 0 0 0 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481 a 8 o 2 34 66 98 1130 162 194 226 258 290 322 354 386 418 450 482 11110 01010 3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483 010 1100 4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484 4 0 419 5 37 69 101 1133 165 197 229 261 293 325 357 389 421 453 48
17. it 16 19 6 7 Magenta 20 23 8 9 Magenta Primary Red split 24 27 9 11 Primary Red 28 31 11 12 Primary Red Flame Red split 32 35 13 14 Flame Red 36 39 14 15 Flame Red Dark Orange split 40 43 16 17 Dark Orange 44 47 17 18 Dark Orange Orange split 48 51 19 20 Orange 52 55 20 22 Orange Yellow split 56 59 22 23 Yellow 60 63 24 25 Yellow Light Green split 64 67 25 26 Light Green 68 71 27 28 Light Green Fern Green split 3 72 75 28 29 Fern Green 76 79 30 31 Fern Green Turquoise split 80 83 31 33 Turquoise 84 87 33 34 Turquoise Cyan split 88 91 35 36 Cyan 92 95 36 37 Cyan Light Blue split 96 99 38 39 Light Blue 100 103 39 40 Light Blue Dark Lavender Split 104 107 41 42 Dark Lavender 108 111 42 44 Dark Lavender Dark Blue split 112 115 44 45 Dark Blue 116 119 45 47 Dark Blue UV Pass split 120 123 47 48 UV Pass 124 127 49 50 UV Pass Multi Color 1 split 128 131 50 51 Multi Color 1 132 135 52 53 Multi Color 1 Multi Color 2 split 136 139 53 55 Multi Color 2 140 197 58 77 CW rotation fast gt slow 198 255 78 100 CCW rotation slow gt fast DMX 512 Protocol 19 Channel DMX Mode Mode Mode 1 2 3 Values Percent Effect Rotating Gobo Wheel 0 0 Open 1 24 0 9 Gobo 1 CCW fast gt slow 25 27 10 11 Gobo 1 static 28 51 11 20 Gobo 1 CW slow gt fast 52 75 20 29 Gobo 2 CCW
18. kg 31 1b Electrical Power and current consumption eee 335 W 1 6 A 230 V 50 Hz AC voltage and frequency EU model 230 V 240 V 250 V 50 Hz AC voltage and frequency US model 100 V 110 V 120 V 225 V 50 60 Hz lc 5 sp seyies best yaa a a T 3 15A EU T 6 3A US Lamps Osram HSD 250 essere 2000 hr 250 W 6000K P N 97010103 Philips MSD 25072 2000 hr 250 W 8500K P N 97010100 Photometric Focused beamiangle ci REPRE 16 Serial Data Link Data 1put i snenie e a eee tie NER ens 3 pin XLR male Data OUtDUL 7 dnte o e ete e TERR 3 pin XLR female Pind omes Qt Eae Me Ad c IO e Olt Edel ground June signal hot Pn 35 B bess ce ceri ertet Mta eme eee eese roots pev PERDU ved nta oue signal cold Specifications 21 appendix c EXTERIOR VIEW mr dad 100 AN o 324 8 i 184 5 f Eod og 7 280 L 533 a dimensions in millimeters wrap safety wire bracket mounting bolts through bracket clamp not shown m PL a ADIP switch e Q Cy o lamp access plate WY tt SSSSSS MA lamp adjustment screws serial number label AC input amp fuse 22 RoboScan Pro 518 appendix d DIP SWITCH TABLE This table s
19. local AC power supply Operating at the incorrect setting can result in poor light output shortened lamp life overheating and dam age to the fixture The settings are printed on the serial number label on the front of the case If the voltage is not within 5 percent of the local supply or if the frequency 50 60 Hz is not the same then the ballast and or transformer must be rewired as described on page 15 6 RoboScan Pro 518 Installing a Plug on the Power Cord WARNING For safe operation the fixture must be grounded earthed The RoboScan Pro 518 may be delivered without a plug on the power cord Following the manufacturer s instructions install an approved 3 prong grounding type plug that fits your supply Connect the wires to the pins as listed below If the pins are not clearly identified or if you have any doubts ab out proper installation consult a qualified electrician Wire Pin Marking Screw color US brown live L yellow or brass blue neutral N silver yellow green ground me green Releasing the Pan Tilt Lock The pan tilt assembly floats in a rubber mount in order to reduce noise To protect the assembly from damage during shipment it is locked with plastic straps and 2 thumbscrews These must be removed before using the RoboScan 1 Cut and remove the 2 plastic straps 2 Remove the thumbscrews from positions A1 and A2 on either side of the pan tilt assembly and store them in positions
20. neee nennen 15 Adjusting the Miror s e oig etr eit eet ir t b tbe t ee Pete 16 appendix a DMX 512 Protocol TENEO RETENTO Talhah ale Otek Se I EEE RON 18 appendix b Specifications E Mula P AE ces buen puce e A Erde ru ala Ll E atlas cena 21 appendix c Exterior View uberi Me AN EEA i MOM LM MAC M Sok anta Da ae E LM wet 22 appendix d DIP Switch Table section 1 INTRODUCTION Thank you for purchasing the Martin RoboScan Pro 518 moving mirror intelligent projec tor It is designed built and programmed to be bright reliable safe and easy to use With proper setup and maintenance the RoboScan Pro 518 will provide years of trouble free operation This manual covers the RoboScan Pro 518 with software version 6 4 The latest information on the RoboScan Pro 518 is always available from your dealer and the Martin web site at http www martin dk RoboScan Pro 518 Safety Information WARNING This product is for professional use only It is not for household use This product presents risks of lethal or severe injury due to fire and heat electric shock ultra violet radiation lamp explosion and falls Read this manual before powering or installing the fixture follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture If you have questions about how to operate the fixture safely please con tact your Martin dealer or call the Martin 24 hour service hotline at 45 70 200 2
21. ntroller s fade time must be set to 0 i e the position must bump from the current value to the next If the RoboScan Pro 518 is set to run vector mode tracking mode can be enabled by programming the speed channels to 0 With 8 bit pan tilt resolution pan and tilt are divided into 256 positions Finer position con trol is possible with 16 bit pan tilt resolution which divides each position into smaller increments DMX Mode Channels PL432 Jumper Mode 1 8 bit Pan Tilt Tracking 7 No jumper Mode 2 8 bit Pan Tilt Vector 9 Jumper on pin 5 and 6 Mode 3 default 16 bit Pan Tilt Tracking 9 Jumper on pin 4 and 5 Channel DMX Mode Mode Mode 1 2 3 Values Percent Effect Strobe Stand Alone Reset Lamp On Off 0 5 0 2 Default 6 10 2 4 Fan low Fan high at all other values 1 11 138 4 54 Strobe fast gt slow 139 170 55 67 Remote stand alone auto trigger Set color to UV Pass 171 202 67 79 Remote stand alone music trigger and effects wheel to 203 235 80 92 Reset fixture 5500 gt 3400K CTC 236 252 93 98 Lamp power ON filter Hold 5 seconds 253 255 99 100 Lamp power OFF Dimmer 2 0 14 0 5 Full dimming 15 239 6 94 Dimming 100 gt 0 240 255 94 100 Nodimming 18 RoboScan Pro 518 Channel DMX Mode Mode Mode 1 2 3 Values Percent Effect Color 0 3 0 1 White 4 7 2 3 White Pink split 8 11 3 4 Pink 12 15 5 6 Pink Magenta spl
22. orrection for low current consumption e Overheating protection Accessories Your Martin dealer can provide you with the following RoboScan Pro 518 accessories Optional gobo set 6 pcs sess P N 43010007 Introduction 5 section 2 INSTALLATION The RoboScan Pro 518 package comes complete with the following items 5 meters XLR XLR cable mains cable mounting bracket and hardware this user manual WARNING Disconnect the fixture from AC power before proceeding Installing and Changing the Lamp The RoboScan Pro 518 is designed to use the Osram HSD 250 and Philips MSD 250 2 dis charge lamps Installing other lamps may damage the fixture The lamp holder is pre adjusted at the factory For precise alignment see Adjusting the Lamp on page 13 To minimize the risk of lamp explosion replace the lamp before usage exceeds 2200 hours 1 Remove the 3 thumbscrews securing the lamp socket assembly to the rear of the RoboScan Gently pull out the assembly If replacing the lamp remove the old lamp from the socket Holding the new lamp in a clean cloth do not touch the glass carefully insert it firmly and squarely into the lamp socket 4 If your fingers touch the glass clean the bulb with a clean lint free cloth wetted with denatured alcohol 5 Replace the lamp socket assembly and tighten the thumbscrews Checking Voltage and Frequency Settings The voltage and frequency settings must match the
23. ps If it does then adjust screw B1 accordingly Tilt Adjustment 1 Use the controller to move the mirror to the upper left position until the top mechanical stop C1 is positioned at the edge of the mirror bracket C2 Loosen the 2 set crews E holding the motor axle while taking care that the motor does not slide vertically from its current position RoboScan Pro 518 Carefully turn the motor and mirror clockwise make sure the motor axle does not turn until there is a distance of 1 2 to 1 mm 1 64 1 32 between the edge of the mirror bracket C2 and the top mechanical stop C1 Tighten the set screws Use the controller to reset the fixture and move the mirror through all extreme positions checking that the bottom mechanical stop D1 does not touch the edge of the mirror bracket D2 If it does then readjust as described above making the distance between C2 and C1 even smaller Service and Maintenance 17 appendix a DMX 512 PROTOCOL The RoboScan Pro 518 supports tracking and vector mode and 8 and 16 bit pan tilt resolu tion The 3 DMX modes and the channel requirements for each are shown below The cor rect mode will depend on your programming preferences and your controller s abilities In tracking mode movement speed is determined directly by the controller s fade time In vector mode speed is determined by a value programmed on a separate DMX channel For smooth movement in vector mode the co
24. rance of 0 1 meters 4 inches around fans and air vents Never place filters or other materials over the lens or mirror The exterior of the fixture can reach temperatures up to 65 C 150 F Allow the fix ture to cool for at least 5 minutes before handling Do not modify the fixture or install other than genuine Martin parts Do not operate the fixture if the ambient temperature Ta exceeds 40 C 104 F To protect yourself and others from injury due to falls When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Block access below the work area whenever installing or removing the fixture Features Remote lamp on off Coated precision optics with adjustable focus Smooth full range dimming Instant blackout and variable strobe effects up to 9 Hz 3 facet prism Frost filter 17 dichroic colors plus CTC filter and white 36 color combinations Continuous bi directional scroll color wheel 5 interchangeable rotating gobos 176 pan and 85 tilt with 16 bit microstep precision Works with Martin and DMX 512 controllers Variable speed control on all functions Preprogrammed stand alone operation Music trigger using built in microphone Power factor c
25. rom the controller It s important to note that the lamp is a cold restrike type meaning that it must be cold before re striking is possible You must wait approximately 10 minutes after having pow ered off the lamp before you can turn it back on again To turn the lamp off via DMX you must set values on 3 channels and hold them for 5 sec onds as follows Channel DMX Value Percent Effect 1 253 255 99 100 Lamp Off 3 120 123 47 48 UV Pass 5500 gt 3400K 5 64 127 25 50 CTC filter Pan Tilt The moving mirror allows you to pan the beam 176 and tilt it 85 Microstep motors pro vide smooth and accurate movement at all speeds DMX modes 1 and 2 offer 8 bit pan tilt resolution while DMX mode 3 and Martin mode provides finer position control with 16 bit resolution Selecting the B O speed blacks out the light while the mirror is moving Color Wheel The Pro 518 has 17 color positions on the color wheel 14 with saturated dichroic colors 2 with multi colors 1 with a special UV pass filter and 1 open white position The wheel can be positioned between 2 colors to split the beam Acceleration control allows variable speed color scrolling Selecting the B O speed blacks out the light while scrolling at highest speed Rotating Gobos The Pro 518 has five rotating gobos The gobos can be rotated in both directions at different speeds The B O speed blacks out the light while the gobos are changing Operation 11

Download Pdf Manuals

image

Related Search

Related Contents

Visor de reportes V5  EMOBILE レンタル約款  GasAlertMicro  

Copyright © All rights reserved.
Failed to retrieve file