user manual - sinclair air conditioners
Contents
1. 3 Check that whether the batteries of air connectioner are changed or not 1 Clean filters and other parts 2 Turn main power off 3 Clear dust from the outdoor unit Trouble shooting Warning Don t attempt to repair the air conditioner by yourself it can cause an electric shock or fire Please check the following items before asking for repair it can save your time and money Trouble Shooting The unit can not operte immediately Once the air conditioner is stopped when the air conditioner is restarted it will not operate in approximately 3 minutes to protect itself Ae Trouble Shooting There s unusual smell blowing from the outlet after operation is started JN 0 Sound of water flow can be heard during operation Creaking noise can be heard when start or stop the unit This is caused by the odors in the room which have been breathed into the air conditioner This is caused by the refrigerant flowing inside the unit Because the air of the room is cooled down rapidly by the cold wind and it looks like the fog This is caused by the deformation of plastic due to the change of tempera ture e Has the power been shut down Is the wiring loose Is the leakage protection switch in operation Is voltage higher or l2. b 3 Mount the air filter properly along the arrow direction in Fig c and then close the panel cover yx Cleaning and Maintenance Take out the healthy filter before cleaning and reinstall it after cleaning according to the installation instruction Pay special attention to that silver ion filter can t be cleaned with water while active carbon photocatalyst low temperature conversion LTC catalyst formaldehyde eliminator ca techin or mite killing filter can but can t with brush or hard things Dry it in the shade or sun after cleaning but not by wiping yr Service Life The healthy filter commonly has its usage lifetime for one year under normal condition As for silver ion filter it is invalid when its surface becomes black green e This supplementary instruction is provided for reference to the unit with healthy filter If the graphics provided herein is different from the physical goods the latter one shall prevail The quantity of healthy filters shall be based on the actual delivery Ea
3. position Use 2 x R03 AAA 1 5 V batteries Do not use rechargeable batteries Replace the used batteries with new batteries of the same type when the display is no longer visible The batteries last around one year The batteries in the remote control must be disposed of appropriately according to the legislation in force in the country concerned TIPS ON STORING AND USING THE REMOTE CONTROL The remote c ontrol can be stored in a special support mounted on the wall The remote control holder is an op tional accessory HOW TO USE THE REMOTE CONTROL To switch the air conditioner on aim the remote control towards the signal receiver The remote control will work at a distance of up to 8 metres from the indoor unit Store the remote control at least 1m from television sets or other electrical appliances OPERATING MODES 1 Selecting the operating mode Each time that the MODE button is pressed the operating mode is changed in the following sequence AUTO COOLING DRY FAN ONLY HEATING 2 FAN mode Each time that the FAN button is pressed the speed is speed is changed in the following seguence AUTO LOW MEDIUM HIGH Ar C SWING 3 Setting the temperature Press once to increase the set temperature by 1 C Press once to decrease the set temperature by 1 C Range of temperature settings available HEATING 16 C 30 C COOLING 16 C 30 C DEHUM
4. to install There must be electricity leakage pro tection switch of enough power capacity and air switch with enough space 25A earth wire cannot be connected to gas pipe water pipe or wires of the lightning rod and telephone User notices Select the most appropriate temperature The airflow direction can be adjusted app It can preclude the electricity wasted ropriately When the unit is running adjust up and down adjusting plate by wireless remote control can adjust vertical direction of Keep room coo air hold the adjust plate that control left and rignt direction ler than outside can adjust horizontal flow direction of air Left and right Louver of upward adjust plate downward direction Don t leave windows and doors Don t blow the wind to animals and open for a long time while operating the air conditioner plants directly It can cause a bad influ lt can decrease the air conditioning capacity ence to them Splashing water on the air conditioner The supply cords of this air conditioner can cause an electric shock and malfu is adopting Y type connection If the supply cord is damaged it must be replaced by man ufacturer or its service agent or a similarly qualified person in order to avoid a hazard nction Air conditioner could be operated Don t use the air conditioner for other with the voltage fluctuation 230 10 purposes such as drying clothes pres Otherwise comp
5. IDIFICATION 16 C 30 C FAN ONLY 16 C 30 C 4 Starting the appliance Press the button When the unit is switched on it will start operating in the mode selected prior to being switched off 5 Adjusting the air flow Pressing the SWING button starts moving the air flow louvers start automatically pressing the SWING button again stops the louvers AUTO OPERATING MODES Press the MODE button until displaying AUTO A in this mode the temperature is set automatically based on the actual room temperature The operating mode and the temperature setting depend on the room temperature In AUTO mode the pre set temperature is 25 C in cooling mode and it is 20 C in heating mode Roomtemperature Mode 20 C 25 C PREVIOUE MODE OR FAN higher than 25 C COOLING Lower than 20 C HEATING AUTOMATIC START After having switched the appliance off press the T ON button to set the time you want the air conditioner to switch back on pressing the T ON button again increases the time by 30 minutes until a maximum of 24 hours from when the TIMEH is set E g If the setting is performed at 4 p m and the TIMER is set to 2 5h the app liance will start at 6 30 p m When the unit is switched on it will start operating in the mode selected prior to being switched off AUTOMATIC STOP When the appliance is on press the T OFF button to set the time you want the air conditioner to switch off p
6. MODE to select run mode of COOL HEAT and SWING etc to check if it can run normally 3 When wireless remote control is losed operation unit by following mode a When unit is halt press the ON OFF button then unit begins running in AUTO micro computer select COOL DRY HEAT or FAN automatically according to indoor temp to make comfort effect Repress ON OFF to stop the unit from running b When unit is running press ON OFF to stop unit from running yr Check after installation It may cause insufficient of cooling heating capacity Is the power voltage the same with that in product nameplate Malfunction or burn out of parts may occur Is the install of circuit and pipeline correct Malfunction or burn out of parts may occur Is the unit earthed safely Creepage may o ccur Is model of wire fits that of regulation Malfunction or burn out of parts may occur Is both the air inlet or outlet vent of indoor Insufficient of cooling heating and outdoor unit blocked Capacity may occur Is length of refrigerant pipe and charge amount recorded Charge amount of refigerant is hard to handle Ey Installation and Maintenance of Healthy Filter sc Installation Instructions 1 Forcibly pull the panel for a specific angle from the two ends of the front panel according to the arrow direction Then pull the air filter downwards to remove it See Fig a 2 Mount the healthy filter onto the air filter as shown in Fig
7. Ms Guide louver Air out Wrapping tape Wireless remote control w hf ve Wa Z hae Wireless remote control operation procedure The remote control sends signals to the appliance AJ C DR I a Meaning of the symbols shown on the liquid crystal display Automatic fan speed Low fan speed Medium fan speed High fan speed Cooling indicator Dehumidification indicator Fan only operation indicator Heating indicator Automatic mode indicator SLEEP indicator Louver swing indicator 1 Liquid crystal display 2 MODE button Used to select the operating mode 3 FAN button Used to set the fan speed in sequence to automatic low medium high 4 SLEEP button Used to set or cancel SLEEP mode 5 SWING button Used to start or stop the movement of the vertical louvers 6 TIMER ON button When the appliance is off this button is used to switch the air conditioner on automatically 7 8 ROOM TEMPERATURE SETTING buttons Used to set the room temperature 9 TIMER OFF button When the appliance is on this button is used to switch the air conditioner off automatically 10 D button Used to switch appliance on or off HOW TO FIT THE BATTERIES Remove the cover of the battery compartment in the direction of d the arrow Fit the new batteries making sure the and signs on the battery match correctly Put the cover back on by sliding it into
8. Space to the ceiling I Space to the wall 15cm or above V 15cm or more Space to the wall piping hole sleeve 300cm 230cm or more Space to the floor Air outlet side PROS Wrapping tape NOTE The indoor unit installation of dual split type unit is taking one of the indoor units for example the installation of another indoor unit is the same as that one Important Notes x he installation must be done by trained and qualified service personnel with reliability according to this manual Contact service center of SINCLAIR before installation to avoid the malfunction due to unprofessional installation When picking up and moving the units you must be guided by trained and qualified person R Installation location Indoor unit 1 The appliance shall not be installed in the laundry 2 The inlet and outlet should not be covered so that the outflow air can reach all parts of the room 3 Install in a location from which the condensation water can be drained out convenienily and that is permitting easy connection with the outdoor unit 4 Avoid a location where there is heat source high humidity or inflamm able gas 5 Install in a location where is strong enough to withstand the full weight and vibration of the unit 6 Ensure the indoor unit installation accord with the installation dimension 7 Be sure to leave enough space to allow access for routine maintenance The indoor unit should be insta
9. USER S MANUAL b h i i i a E AIR CONDITIONING CONTENTS The instructions before use Models and specifications Names and functions of each part wireless remote control opreation procedure Change batteries for the wireless remote control The best operating methods User notices O c 5 E o amp 5 O 5 Cc Q 5 m ab Q O Care and maintenance Trouble shooting Installation dimension diagram The selection of installation location Install the indoor unit est operation and check after installation Installation and aftersales service Installation and Maintenance of Healthy Filter Thank you for choosing SINCLAIR air conditioner please read this owner s manual carefully before operating the unit and keep it carefully for consultation Please read the following carefully before operating the unit wire must be connected to the special grounding devices Can t be connected to the water pipe gas pipe sewage drain or the places where are not reliable earthed Don t apply the cold wind to the body for a long time It cause the physical condition deferioration and health problems WARNING Never damage the wires or use the inapplicable wires Otherwise it may cause elec tric shock or fire When having a buming sm ell or smoke please turn off the power supply and contact with the service center If abn
10. lled at 2 3m or higher above the floor 8 Select a place about 1m or more away from the TV set or any other electric appliances 9 Select a place where the air filter can be easily taken out 10 Do not use the unit in the immediate surroundings of a laundry a bath a shower or a swimming pool NOTE Install in the following place may cause malfunction If it is unavoidable contact with service center please e Place where machine oil is used 3 e The place where a lot of salinities such as coast exists Place where a sulfured gas such as the hot spring zones Is generated e Place where high frequency waves are generated by radio equipment welders and medical equipment e Other place with special circumstance Ea Install the indoor unit XX Install the rear panel 1 Always mount the rear panel horizon tally As the water drainage pipe at the left this side should not be too high when adjusting the rear panel it had better to adjust this side a little lower 2 Fix the rear panel on the selected location 3 Be sure that the rear panel has been fixed firmly enough to withstand the weight of an adult of 60kg furthermore the weight should be evenly shared each screw yk Install the drain hose 1 For well draining the drain hose shoule be placed Wirenched at a downward slant Bont 2 Do not wrench or bend the drain hose or flood its Tea be end by water x x 3 When the long drainage ho
11. ormity still exists the air conditioner could be dam aged or may cause electric shock or fire Cut off the power Don t insert your hands or stick into the air intake or outlet vents It can cause danger Don t attempt to repair the air conditioner by your self The improper maintenance will cause electric shock or fire should contact with the service center N 3 Don t use fuse excluding the fuse of correct capacity Improper wire could cause the break down or fire Don t place a space heater near the air conditioner Airflow from the air condi tioner can cause incomp lete combustion to the sp ace heater and may cause intoxication of carbon mo Keep chemical spray away from the outdoor un it for more than 1 meter It is likely to ignite and ex Don t block the air intake or outlet vents of both the outdoor and indoor units It can decrease the air con ditioning capacity or cause a malfunction Models and specifications Cooling capacity W 2100 2900 3500 Heating capacity W 2600 2800 3800 Rated power supply 220 240V 50Hz Climate Type Waterproof level Isolation Weight kg Indoor unit boundary 4900x290 150 dimensions WxHxD mm If there is any change please see the nameplate for actual data Working temperature range itor site BECO 03 215 W Names and functions of each part Air in Displayer Front panel
12. ower Is TIMER ON in operation Is SET TEMP suitable e Is air inlet or outlet obstructed Are air filters dirty Are the windows and door closed Is indoor fan speed set at low speed Is there any other heat source in your room Wireless remote control is not available Remote control can t be used occasionally when the air conditioner is disturbed or changing its functions frequently At that time pull out the power plug and insert it again to recover the operation Is the remote control out of effective disance to the indoor unit Are there any obstruction between the remote control and the signal receptor Replace the worn batteries of remote control if the voltage of the batteries is not sufficient Immediately stop all operations and plug out contact the dealer in following situations If you have any guestions please inform the service center A There are harsh sound during operation A The fuse and protection switch often trip off A Carelessly splash water or somthing into the unit or wireless remote control A Water is leaking in the room A There is an abnormal heat in power supply cord and power plug A Installation dimension diagram The dimensions of the space necess ary for correct installation of the appliance including the mininum permissible distances to adjacent strucyures 15cm or more
13. ressing the T ON button again increases the time by 30 minutes until a maximum of 24 hours from when the TIMER is set E g If the setting is performed at 8 30 p m and the TIMER is set to 3 5h the appliance will switch off at midnight DEHUMIDIFICATION MODE Press the MODE button until displaying the DRY mode The appliance will start according to the room temperature and the set temperature e f the room temperature is lower than the set temperature the compressor the outdoor unit will stop e If the room temperature is more than 0 5 C above the set temperature the appliance automatically starts in dehumidification mode SLEEP MODE When the unit is cooling or drying if SLEEP operation is set SET TEMP would increase 1 C in 1 hour and 2 C in 2 hours When the unit is heating if SLEEP operation is set SET TEMP would decrease 1 C in 1 hour and 2 C in 2 hours 10 The best operating methods lt aims at saving the energy and operating the unit conveniently and safely Adjust to the suitable temperature Too cool will do harm to the health Clean the air filter seriously and maintaining it carefully Please take out the batteries from the wireless remote control when it is not in use Avoid directly lighting and cool air leaking Earth wire Earth wire must be connected to the special device of the building If haven t please ask the professional
14. ressor would vibrate erving foods etc terribly to damage refrigeration system Care and Maintenance Warning A Stop the unit and pull out the plug before cleaning the unit or electic shock will be happened A Don t get wet the unit for it will cause the electric shock make sure don t wash the unit by water A The volatile liquid such as thinner or gas will damage the face of unit only using the soft cloth and wet cloth with neutral cleaning fluid to clean the body of unit Unpick and wash the filter 1 Uplift the panel upwards by hand according to the direction of arrowhead 2 Put down the panel according to direction of arrowhead 3 Uplift the panel a little bit according to the direction of arrow 1 then take out the filter according to arrow 2 clean the filter by cleaner or water when the filter is dirty oil it can be washed by warm water below 45 C dissolving with neutral cleaning fluid then dry it on the shady and cool place 1 Uplift the panel a little bit from the direc tion of arrowhead 1 then insert the filter below the panel according to arrowhead 2 2 Uplift the panel according to the direction of arrowhead to the location shown as Fig 3 Insert the clamp Aj gBj C back to three the rotating shaft and cover the panel Check before use 1 Be sure that nothing obstructs the air outlet and intake vents 2 Check that whether ground wire is properly connected or not
15. rom the left or right side cut off the tailings of the pipe left from chassis of main unit as shown in fig 4 c 1 Cut off tailings 1 when only power cord is routed 2 Cut off tailings 1 and 2 when connection pipe and power cord are routed Methods 2 are recommended piping ways 2 After wrapped pipe and wire pull them though the pipe hole as shown in fig 5 3 Hang the mounting slot behind indoor unit on the pothook of the rear panel and move it to check if it is firm enough as shown in fig 6 4 Ensure the install height of indoor unit is 2 3m or higher 90 a Tailings 2 Tailings 1 a Fig 4 O 4 Left pipe 9 Rear left pipe Wrapping strap Coonection pipe Power connect wire Drainage hose Signal control wire Fig 5 A im Lp Pj Test operation and check after installation x Test operation 1 Preparation for trial run 1 Don t turn on power supply if entire installations are not completed 2 Connect of control circuit should be correct Heating indicator ON OFF button Cooling indicator all wire connect should be firm Running indicator 3 Cut off valves of both thick and thin pipes should be turned on 4 All scattered components especially metal scrap thrum etc should be cleared from unit 2 Test operation method 1 P ress ON OFF on wireless remote control after connecting to power supply unit begins running 2 Press
16. se passing through indoor e a ea should wrap the insulation materials Fas y lt Install the connection pipes Connect the connection pipes with the relevant union pipes of the indoor unit and tighten the flare nut of the connection pipes sh m cover of connection connection power inside f and outside the unit Note A Connect the connection pipes with the indoor unit firstly and the outdoor unit secondly am ABe careful in bending the connection pipes or you will damage the pipe Alf the tightening torque is too great in tightening the flare nuts leakage will happen A The appliance shall be installed in accordance with national wiring regulations yx Electric wiring 1 Open the panel upwardly 2 Disassembly the fixing bolts of connection cover shown in the Fig at right side 3 power connecting wire cross through down to up from the bottom of case 19 4 Connect blue wire in power connect wire onto N 1 terminal black wire onto 2 terminal brown wire onto 3 terminal yellow green wire i e earth wire onto terminal as shown in fig 3 and press the power connect wire by wire groove that in front of line bank that installed in electric box 5 Install the cover plate on where it was an d tighten screws 6 Cover panel Line bank Fig 3 X Install Indoor Unit 1 Please refer to the fig a and b for routing piping type of indoor unit When routing the piping wiring f
Download Pdf Manuals
Related Search