Powermoon Profi 1 Manual
Contents
1. Safety Instructions POWERMOON Using Instructions Electrical Requirements Care And Maintenance Parts Replacement incl bulb replacement Trouble Shooting 1 Safety Instructions Caution before using the POWERMOONG read all instructions POWERMOONG is a fuseless system and can only be used with power sources that have a circuit breaker POWERMOONs can be used both indoors and outdoors The system is IP54 approved weather and rain proof After unpacking Check all electrical cables for damages or cuttings Make sure that the bulb is free of any packing material used for transport Check bulb for cracked glass or any other transport caused damage Vibration during transportation could cause bulb to shatter Use gloves Check if bulb is properly screwed into E39 socket Screw bulb in properly before start using POWERMOON P Use gloves If the POWERMOONG has already been used check the following before reuse Cables should not be cut or damaged Power plug and plug between Ballast and POWERMOON lamp should be checked for burn damage In case of any damage check with a professional electrician before continuing Safety instructions and restrictions for your own operational safety The POWERMOONG and all additional equipment such as POWERMOON ballast telescopic pole etc can only be used for lighting purposes Any other use happens at users own risk and liability POWERMOON components should not2. b ya aT ZN ae Ke ce m pe or Sy fe VE Ses D Sy ere 43 cee ae og A Eo N f F do ae it RES K 9 Plug ballast i in to power source Bulb ignites in around 0 200 seconds Attention Always make sure to connect to existing and running power sources Interruptions and gaps in electricity flow may cause delays in ignition of bulb or even result in its damage Attention Once disconnected from power HQI bulb takes 5 to 6 minutes to ignite again Turn off POWERMOON 1 Turn of POWERMOON by pulling power plug out of power source 2 Wait 30 seconds Then pull plug out of the ballast Attention The Ballast is compensated with a capacitator During the first seconds the loaded condenser could give an un harmful electric shock The System complies with UL TUV US CSA regulations The condenser will be discharged through a discharging resistor 3 Close POWERMOON by holding black handle bar and pulling pin Slowly close POWERMOON by letting handle bar slide uo POWERMOON middle axis Attention Wait until bulb has cooled off Approx 5 10min 3 Electrical requirements and data Voltage 100 115V Hertz 50 60Hz Current 1 x 4A Bulb 1000 W HQI 4000 to 4400 Calvin 80 000 to 110 000 Lumen Amps 7 8 5 Thread E39 Why a ballast It transforms the common power of 110V in to the final using power 4 Care and maintenance 10 The POWERMOON may get damp wi
3. be used mixed together with other lighting systems or components If used or mixed with other systems or components POWERMOON O warranty is no longer valid Attention when mounting the POWERMOON onto a tripod or pole Ensure that the complete system has a secure stand to prevent it from toppling Inner steles need to be horizontal All screws must be tightened at all times Keep safety distance to roads pedestrians animals cars mobiles buildings etc We advise the usage of fixing lopes when lighting traffic routes for example POWERMOONG fixing lopes One guy rope should then be in right angle to road to secure tripod from toppling on to road Alternatively weigh down POWERMOONG tripod telescopic pole with additional material sandbags concrete blocks etc POWERMOONBO Lights and signals Make sure that the POWERMOONG balloon or its light never mask other lights such as railway crossings signposts signals and traffic lights When lighting crowded areas such as sport events music festivals always secure the area around the balloon with barrier tape Also secure the guy ropes Environmental protection Emission of light in residential areas or protected nature reserves could be disturbing Read city guidelines for emission of light before use Inform all involved circles and facilities Disturbances to environment are possible when not using sound proof generators as electric power supply Make sure to use up
4. to date power supplies Clearance distance Radiation heat protection Always keep a clearance distance of min 3 feet to easy burnable materials such as wood plastics and textile such as curtains wooden ceiling wooden walls plastic foam insulation etc Keep lamp away from materials that may burn Do not use a POWERMOON near open or leaking highly inflammable mediums gasoline and gas Do not use POWERMOONG in EX Zones Do not use POWERMOONO for salvage or rescue work with tank ship disasters damages in refineries or gas pipelines Lighting inside tanks big chimneys and floating bodies POWERMOONS should only be used with a suitable insulating transformer when inside enclosed areas and chimneys as well as floating metal pontoons ships and wrecks In such cases an electrician should test safety before starting Check regional rules of conduct with a professional electrician when using the POWERMOONG or other electric devices on ships If a person and a POWERMOON are situated on the same metal base insulation and earth grounding precautions must be taken Keep POWERMOON away from pylons and high voltage sources Safety margins should be considered carefully when a POWERMOON is installed on vehicles and construction equipment High Voltage Cables should be at least approx 160 ft 50m linear distance Overhead railway electric lines should be kept at a distance of 8ft 2 5m Check regulation clearance of trip
5. using instructions 1 Take POWERMOON cords out of cylinder before taking out POWERMOON 2 Take POWERMOON O out of cylinder by gripping pin and gently pulling the POWERMOON 3 Place POWERMOON O with bottom pin on solid ground Grip black handle bar pull pin and press down until POWERMOON is fully opened and locked in place 4 Check if Velcro is closed all around and if transparent balloon cover is not damaged In case of bigger damages repair with delivered repair kit or change cover 5 Lift POWERMOONG by gripping bottom pin with one hand and upper cover with other hand Mount POWERMOONG on suitable tripod or other mast 6 If using a tripod bring it up to desired height Optimal installation height of balloon is 13 16ft 4 5 meters 8 Attention Always watch hands when bringing tripod up and down Attention Always make sure to tighten all screws when changing tripod segments Attention Pay attention to wind and weather We advise to tie rope tripods or other masts as wind and weather conditions might change Attention Make sure that inner steles are horizontal and all three tripod stands are on ground This could for example not be the case if middle pole is touching ground as well 8 Plug POWERMOON cord in to ballast Pay attention to red markings and attach firm by closing lid E G satel eee nt Fs Ss 23 pains Pt Hg K asa A eee ere ax at tk me pp pe yes
6. POWERMOON Profil 1000 Watt HQI USING INSTRUCTIONS US Patent No US 6 305 827 B1 US TM Reg No 2 537 683 Canadian Patent No 2311220 Congratulations on your purchase of a POWERMOON balloon lighting system Your POWERMOON O Profil is the most up to date glare free floodlight system on the market and worldwide the only balloon light that works on basis of a solid and robust steel spring open and close mechanism This system ensures that your POWERMOON always stays open while in use Even when not running the POWERMOONG can stay open for days or even weeks Just as well as you can close it within seconds Your POWERMOONG is IP54 approved which means wind and weather resistant The benefits of a POWERMOONG balloon lighting system No glare No harsh shadows Wide light distribution High portability Small storage Solid and robust gt safety and work efficiency at night increase enormously One more benefit Great looks and elegant design To ensure best possible lighting results and correct usage please read the manual carefully If you have any questions need further information or advice never hesitate to contact us POWERMOONG Enterprises Ltd 113 Dials Drive Woodstock GA 30188 USA www powermoon com Phone 770 516 2266 Toll Free 1877 MOON 085 Fax 770 516 2267 Your POWERMOON team Table of contents Page 4 Page 7 Page 10 Page 11 Page 11 Page 13
7. ly be executed by a professional electrician All necessary spare parts are available from POWERMOON Enterprises Ltd 14
8. ods for rail tracks Different regulations apply for different regions Check safety regulations and zones for airports ports and oil refineries Different regulations apply for different regions Ensure that the power supply cable of POWERMOON cannot be damaged or cut off by passing traffic and trains Pedestrians should not be endangered by wires which they could stumble over Take care when running POWERMOONE with other machines on the same generator or power source Warning Check capacity of small generators of less than 15kVA before letting large machines use it at the same time as the POWERMOON Strong inductive and capacitance machines like POWERMOONs or engines immersion pumps have influence on phases and sine curves of generators Do not attach electronic equipment like computers televisions or hi f s This equipment could be damaged when turning the POWERMOON on and off due to the surge in voltage This occurs especially if the electronic control unit is defective Violation of the above results in responsibility of user and frees manufacturer from all liabilities Violation of the above and any defect on other machines equipment and instruments coming thereof caused for example by regeneration back coupling is not the manufacturers responsibility 2 POWERMOONE using instructions Attention Never switch POWERMOON O on before it has been completely assembled Always pay attention to warning labels and
9. re plugs correctly attached 2 Check if plug connection from Ballast to POWERMOON is tight Check 13 3 Check if bulb is screwed in socket correctly and that it shows no damages Use hand gloves 4 Depending on outside temperature the ignition process of the bulb might take up to 3 5 minutes Should any fall of voltage or any interruption of current flow occur the bulb will go off and will need time to cool down and reignite after about 10min The balloon can stay attached to current flow and will automatically reignite 5 Should the bulb flicker the power source might not deliver enough current This often happens with smaller standard generators Recommended are generators with inverter starting at about 1 7kVA or regular generators with about 2 8kVA Also check whether bulb is screwed in socket correctly It can happen that during transport a bulb loosens Even though the bulb might ignite when not screwed in socket correctly sparks might cause smouldering and bulb as well as socket might melt Change bulb and socket if this should have happened 6 Should the balloon still not work after checking the bullets 1 5 either the bulb the ignition system or the ballast might be defective Change bulb first Then check current coming from ballast 110V are required Should ballast not deliver required voltage it might be broke A possibly necessary exchange of the micro fuse the capacitor or the electromagnetic coil should on
10. t in dangerous smouldering or other uncontrollable electricity flow Attention Never use smaller watt bulb e g 400W or bigger watt bulb e g 2000 W Information on bulb positioning The bulb position vertical is predetermined by the way the POWERMOON is constructed All bulbs from 1000W will ignite and operate Bulbs that usually are used in horizontal position can be used as well Using these bulbs in an upright position will only reduce the lifespan of the bulb by approx 50 as the anodes and cathodes burn down unevenly Bulb types and manufacturers POWERMOON US 1000W HAQI E39 5 Close burst cage by tightly screwing down upper screw 6 Close Velcro of bottom and top cove by starting at the corners Repair kit for small holes in balloon cover Small holes in the lower white cover can be pasted over with the self adhesive repair kit which is delivered together with the POWERMOON 6 Trouble Shooting 6 1 Mechanical Defects The POWERMOON won t open Should the POWERMOON not open properly grip handle won t slide easily over glider twist and turn grip handle while holding POWERMOON main bell firm Try to press down and open POWERMOON again 6 2 Electrical Defects The POWERMOON won t ignite and light up 1 Check power source 110V 50Hz should be available Check cables from power source to ballast on possible damages or loose connections Are any cables broken Is there any interruption in current flow A
11. th use Always let the POWERMOON dry out before storing it in cylinder small holes in translucent cover can be pasted with self adhesive repair kit Dirt on both top and bottom cover can be wiped off with thin soap liquid Do not clean cover with any solvent as it will be destroyed Leave defective cables or broken plugs for an electrician to repair 5 Parts replacement Balloon cover replacement Caution We advise to wear protective goggles when changing cover of balloon Reason POWERMOON O balloons open through stainless steel springs which might be uncontrollable If cover is severely damaged it must be changed 1 Change cover of balloon by opening Velcro 2 Open elastics 3 Apply new cover 4 Close elastics 5 Close Velcro of bottom and top cove by starting at the corners For further info on how to change cover please visit website www powermoon com Bulb replacement 11 Attention Precautions Completely unplug POWERMOON from any power source Allow used bulb to cool off before replacing Wear gloves and protective goggles Bulb is under high pressure and could explode implode Caution Do not look in to burning bulb Lamp radiates strong UV Light 1 Carefully open two 2 Velcro segments while balloon is fully opened bulb 4 Insert new bulb by screwing It to the right in to socket Make sure it sits correct firm 12 Attention Improper insertion for example loose bulb may resul
Download Pdf Manuals
Related Search