Keysight Technologies 34460A / 34461A / 34465A / 34470A
Contents
1. a E MESSBAR MEHR da talec Upgrade process Customer installable hardware Software license Software license Accessory kit Software license Software license Calibration certificate The warranted performance of a calibrated instrument that has been stored for a minimum of 2 hours within the operating tem perature range of O 55 C and after a 60 minute warm up pe riod All specifications include measurement uncertainty and were created in compliance with ISO 17025 methods Data published in this document are specifications spec only where specifically indicated Typical typ The characteristic performance which 80 or more of manu factured instruments will meet This data is not warranted does not include measurement uncertainty and is valid only at room temperature approximately 23 C Nominal nom The mean or average characteristic performance or the value of an attribute that is determined by design such as a connec tor type physical dimension or operating speed This data is not warranted and is measured at room temperature approximately 23 C Measured meas An attribute measured during development for purposes of com municating the expected performance This data is not warranted and is measured at room temperature approximately 23 C Tear The temperature at which the instrument was calibrated nderungen und Irrt mer vorbehalten dataTec 18 11 2015 Keysigh2. 0 005 0 100 0 010 0 230 0 020 0 150 0 010 0 012 0 020 0 012 0 020 Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 5010 info datatec de With ACAL 1 Temperature coefficient C 0 0001 0 0005 0 0001 0 0001 0 0001 0 0001 0 0001 0 0001 0 0001 0 0001 0 0002 0 0005 0 0002 0 0001 0 0002 0 0001 0 0002 0 0001 0 0002 0 0002 0 0030 0 0004 0 0100 0 0001 0 1000 0 0001 Temperature coefficient C 0 0020 0 0010 0 0015 0 0006 0 0015 0 0004 0 0015 0 0005 0 0020 0 0020 0 0020 0 0005 0 0050 0 0010 0 0050 0 0020 0 0050 0 0010 0 0010 0 0020 0 0010 0 0010 www datatec de specifications 344 0A Temperature PT100 DIN IEC 751 5 KQ thermistor K J 1 E N thermocouples 4 R thermocouples 250 1760 C True RMS AC voltage 1 gt 16 100 mV 1 V 10 V 100 V and 750 V ranges 3 9 Hz 5 10 Hz 10 Hz 20 kHz 20 50 kHz 50 100 kHz 100 300 kHz True RMS AC current 7 100 pA 1 mA 10 mA 100 mA 1 A ranges 3 Hz 5 kHz 5 10 kHz typ 3 A range 3 Hz 5 kHz 5 10 kHz typ 10 Arange 3 Hz 5 kHz 5 10 kHz typ Capacitance 1 0000 nF 10 000 nF 100 00 nF 1 0000 uF 10 000 uF 100 00 UF Frequency 100 mV 1 V 10 V 100 V and 750 V ranges 3 40 Hz 40 100 Hz 100 Hz 1 kHz 1 300 kHz Square wave 18 20 Additional frequency errors of reading Apertu
3. Specifications are for the voltage measured at the input terminals The 1 mA test current is typical Variation in the current source will create some variation in the voltage drop across a diode junction See user manual for details Actual measurement range and probe errors will be limited by the selected probe Probe accuracy adder includes all measurement and ITS 90 temperature conversion errors PT100 Ro settable to 100 Q 5 Q to remove the initial probe error The internal reference junction uses the U1180A or equivalent adapter This has a typical performance of 1 0 C This internal reference junction can be adjusted for better accuracy An external reference junction can also be used Specifications are for sinewave input gt 0 3 of range and gt 1 mVrms 750 ACV range limited to 8 x 10 Volt Hz For each additional volt over 300 Vrms add 1 mVrms of error Low frequency performance three filter settings are available 3 Hz 20 Hz 200 Hz Frequencies greater than these filter settings are specified with no additional errors Specifications are for sinewave input gt 1 of range and gt 10 Arms Specifications are for sine wave input unless stated otherwise Square wave input specified for 10 300 kHz for 1 second aperature For shorter aperatures the minimun frequency requires gt 2 cycles Input gt 100 mV For 10 mV to 100 mV inputs multiply of reading error x10 Amplitude 10 120 of range except 14 100 for the 750
4. www datatec de 7 specifications 34460A 34460A accuracy specifications of reading of range These specification are compliant to ISO IEC 17025 for K 2 Range frequency DC voltage 100 mV 1V 10V 100 V 1000 V True RMS AC voltage 100 mV 1 V 10 V 100 V and 750 V ranges 3 9 Hz 5 10 Hz 10 Hz 20 kHz 20 50 kHz 50 100 kHz 100 300 kHz Resistance 7 Test current 1000 1 mA 1kO 1 mA 10 kQ 100 uA 100 kQ 10 uA 1 MQ o LA 10 MQ 500 nA 100 MQ 500 nA 10 MO DC current Burden voltage 100 uA lt 0 011 V 1 mA lt 0 11 V 10 mA lt 0 05 V 100 mA lt 05 V TA lt 0 7 V 3A lt 2 0 V Capacitance 1 0000 nF 10 000 nF 100 00 nF 1 0000 uF 10 000 uF 100 00 uF a dataTec Ferdinand Lassalle Str 52 24 hours Tea Ue 0 0040 0 0060 0 0030 0 0009 0 0025 0 0004 0 0030 0 0006 0 0030 0 0006 1 00 0 02 0 38 0 02 0 07 0 02 0 13 0 04 0 58 0 08 4 00 0 50 0 0040 0 0060 0 0030 0 0008 0 0030 0 0005 0 0030 0 0005 0 0030 0 0010 0 015 0 001 0 300 0 010 0 010 0 020 0 007 0 006 0 007 0 020 0 010 0 004 0 050 0 006 0 180 0 020 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 72770 Reutlingen 90 days Tea 9 C 0 0070 0 0065 0 0060 0 0010 0 0050 0 0005 0 0065 0 0006 0 0065 0 0010 1 00 0 03 0 38 0 03 0 08 0 03 0 14 0 05 0 63 0 08 4 00 0 50 0
5. 0 003 0 005 0 003 0 011 0 005 0 060 0 008 0 200 0 020 0 0006 0 0005 0 0006 0 0001 0 0006 0 0001 0 0006 0 0001 0 0010 0 0002 0 0030 0 0004 0 1500 0 0002 0 0020 0 0030 0 0020 0 0005 0 0020 0 0020 0 0020 0 0005 0 0050 0 0010 0 0050 0 0020 0 05 0 05 0 05 0 01 0 05 0 01 0 05 0 01 0 05 0 01 0 05 0 01 www datatec de specifications 34460A Range frequency 24 hours 90 days 1 year 2 years Temperature Tae Ta 9C Taro C TaS C coefficient C True RMS AC current gt Burden voltage FOO ie WOM eine lt L071 lt lt av 100 mA ranges 3 Hz 5 kHz 0 10 0 04 0 10 0 04 0 10 0 04 0 10 0 04 0 015 0 006 5 10 kHz typ 0 10 0 04 0 10 0 04 0 10 0 04 0 10 0 04 0 030 0 006 1 A range Oy 3 Hz 5 kHz 0 10 0 04 0 10 0 04 0 10 0 04 0 10 0 04 0 015 0 006 5 10 kHz typ 0 10 0 04 0 10 0 04 0 10 0 04 0 10 0 04 0 030 0 006 3 A range ZON 3Hz 5kHz 0 23 0 04 0 23 0 04 0 23 0 04 0 23 0 04 0 015 0 006 5 10 kHz typ 0 23 004 0 23 0 04 0 23 0 04 0 23 0 04 0 030 0 006 Continuity 1 kQ 0 002 0 030 0 008 0 030 0 010 0 030 0 012 0 030 0 0010 0 0020 Diode test Ov 0 002 0 030 0 008 0 030 0 010 0 030 0 012 0 030 0 0010 0 0020 DC ratio typ normalized input accuracy normalized reference accuracy Temperature PT100 DIN IEC 751 Probe accuracy 0 05 C 5 KQ thermistor Probe accuracy 0 1 C Frequency speci
6. Tea IC 0 007 0 005 0 007 0 002 0 007 0 001 0 007 0 003 0 007 0 020 0 010 0 004 0 050 0 006 0 180 0 020 0 050 0 010 0 002 0 010 0 002 0 010 normalized input accuracy normalized reference accuracy 1 year Tacar 9 C 0 0040 0 0035 0 0020 0 0004 0 0016 0 0002 0 0038 0 0006 0 0038 0 0006 0 0060 0 0040 0 0040 0 0005 0 0040 0 0005 0 0040 0 0005 0 0070 0 0005 0 025 0 001 0 300 0 001 3 000 0 001 90 days Tea 9 C 0 030 0 005 0 030 0 002 0 030 0 001 0 030 0 005 0 030 0 020 0 030 0 005 0 070 0 010 0 200 0 020 0 120 0 010 0 008 0 020 0 008 0 010 2 years Taca 9 C 0 0045 0 0035 0 0025 0 0004 0 0020 0 0002 0 0040 0 0006 0 0040 0 0006 0 0070 0 0040 0 0050 0 0005 0 0050 0 0005 0 0050 0 0005 0 0080 0 0005 0 030 0 001 0 400 0 001 4 000 0 001 1 year Ten 9 C 0 050 0 005 0 050 0 002 0 050 0 001 0 050 0 005 0 050 0 020 0 050 0 005 0 080 0 010 0 200 0 020 0 120 0 010 0 010 0 020 0 010 0 010 Non ACAL Temperature coefficient C 0 0005 0 0005 0 0005 0 0001 0 0005 0 0001 0 0005 0 0001 0 0005 0 0001 0 0006 0 0005 0 0006 0 0001 0 0006 0 0001 0 0006 0 0001 0 0010 0 0002 0 0030 0 0004 0 1000 0 0001 1 0000 0 0001 2 years Tea 9 C 0 060 0 005 0 060 0 002 0 060 0 001 0 060 0 005 0 060 0 020 0 060
7. 0 10 0 40 0 10 1 year Tea 9 C 0 0050 0 0035 0 0040 0 0007 0 0035 0 0005 0 0045 0 0006 0 0045 0 0010 1 00 0 03 0 35 0 03 0 06 0 03 0 12 0 05 0 60 0 08 4 00 0 50 0 010 0 004 0 010 0 001 0 010 0 001 0 010 0 001 0 010 0 001 0 040 0 001 0 800 0 010 0 050 0 025 0 050 0 006 0 050 0 020 0 050 0 005 0 100 0 010 0 200 0 020 0 120 0 010 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 Has 2 FEE 2 gt I i efits gt om J toy 2 r ay COY ti u gt rl 2 years Tea 9 C 0 0065 0 0035 0 0055 0 0007 0 0050 0 0005 0 0060 0 0006 0 0060 0 0010 1 00 0 03 0350 03 0 07 0 03 0 13 0 05 0 60 0 08 4 00 0 50 0 012 0 004 0 012 0 001 0 012 0 001 0 012 0 001 0 012 0 001 0 060 0 001 0 800 0 010 0 060 0 025 0 060 0 006 0 060 0 020 0 060 0 005 0 120 0 010 0 230 0 020 0 150 0 010 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 Temperature coefficient C 0 0005 0 0005 0 0005 0 0001 0 0005 0 0001 0 0005 0 0001 0 0005 0 0001 0 100 0 003 0 035 0 003 0 005 0 003 0 011 0 005 0 060 0 008 0 200 0 020 0 0006 0 0005 0 0006 0 0001 0 0006 0 0001 0 0006 0 0001 0 0010 0 0002 0 0030 0 0004 0 1500 0 0002 0 0020 0 0030 0 0020 0 0005 0 0
8. 001 4 000 0 001 1 year Tea 9 C 0 050 0 005 0 050 0 002 0 050 0 001 0 050 0 005 0 050 0 020 0 050 0 005 0 080 0 010 0 200 0 020 0 120 0 010 0 010 0 020 0 010 0 010 Non ACAL Temperature coefficient C 0 0005 0 0005 0 0005 0 0001 0 0005 0 0001 0 0005 0 0001 0 0005 0 0001 0 0006 0 0005 0 0006 0 0001 0 0006 0 0001 0 0006 0 0001 0 0010 0 0002 0 0030 0 0004 0 1000 0 0001 1 0000 0 0001 2 years Tee 0 060 0 005 0 060 0 002 0 060 0 001 0 060 0 005 0 060 0 020 0 060 0 005 0 100 0 010 0 230 0 020 0 150 0 010 0 012 0 020 0 012 0 020 lam 5 s sj a 3 E CG ee VD ANA gt g AD ti r gt With ACAL Temperature coefficient C 0 0002 0 0005 0 0002 0 0001 0 0002 0 0001 0 0002 0 0001 0 0002 0 0001 0 0002 0 0005 0 0002 0 0001 0 0002 0 0001 0 0002 0 0001 0 0002 0 0002 0 0030 0 0004 0 0100 0 0001 0 1000 0 0001 Temperature coefficient C 0 0020 0 0010 0 0015 0 0006 0 0015 0 0004 0 0015 0 0005 0 0020 0 0020 0 0020 0 0005 0 0050 0 0010 0 0050 0 0020 0 0050 0 0010 0 0010 0 0020 0 0010 0 0010 www datatec de specifications 34465A Temperature PT100 DIN IEC 751 5 kQ thermistor K J 1 E N thermocouples R thermocouples 250 1760 C True RMS AC voltage 16 100 mV 1 V 10 V 100
9. 011 0 007 0 011 0 001 0 011 0 001 0 011 0 001 0 011 0 001 0 020 0 001 0 800 0 010 0 040 0 025 0 030 0 006 0 030 0 020 0 030 0 005 0 080 0 010 0 200 0 020 0 50 050 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 1 year Tea 9 C 0 0090 0 0065 0 0080 0 0010 0 0075 0 0005 0 0085 0 0006 0 0085 0 0010 1 00 0 03 0 38 0 03 0 09 0 03 0 15 0 05 0 63 0 08 4 00 0 50 0 014 0 007 0 014 0 001 0 014 0 001 0 014 0 001 0 014 0 001 0 040 0 001 0 800 0 010 0 050 0 025 0 050 0 006 0 050 0 020 0 050 0 005 0 100 0 010 0 200 0 020 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 Yin 00 557 AM Sn HAWK Sut ory 067 1790 Sangis 259 2 years Tea 9 C 0 0115 0 0065 0 0105 0 0010 0 0100 0 0005 0 0110 0 0006 0 0110 0 0010 1 00 0 03 0 38 0 03 0 10 0 03 0 16 0 05 0 63 0 08 4 00 0 50 0 017 0 007 0 017 0 001 0 017 0 001 0 017 0 001 0 017 0 001 0 060 0 001 0 800 0 010 0 060 0 025 0 060 0 006 0 060 0 020 0 060 0 005 0 120 0 010 0 230 0 020 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de pone ASAS a fl Temperature coefficient C 0 0005 0 0005 0 0005 0 0001 0 0005 0 0001 0 0005 0 0001 0 0005 0 0001 0 100 0 003 0 035
10. 10 mA range For 0 2 PLC multiply the above range error by 5x onthe 1 A and 10 A ranges and by 10x for the 10 mA range Maximum reading rates for 0 01 of AC step additional error Additional settling delay required when input DC level varies For external trigger or remote operation using default settling delay Delay Auto 6 Maximum useful limit with default settling delays defeated Noise performance for DC voltage DC current and resistance 34465A amp 34470A Integration time Digits RMS Noise adder of range fixed base 34465 34470 DC volts Ohms DC current 100 PLC 1 67 s 2 OVAL 0 0 0 10 PLC 167 ms 200 ms ORJI 0 0 0 1 PLC 16 7 ms 20 ms 6 2 7 0 0001 0 5 uV 0 0001 0 5 mQ 0 0006 0 01 nA 0 2 PLC 3 ms 3 ms 6 6 0 0005 3 uV 0 0010 10 m 0 0050 5 nA 0 06 PLC 1 ms 1 ms 6 6 0 0020 3 uV 0 0020 10 m 0 0070 10 nA 0 02 PLC 400 us 300 us 6 6 0 0020 3 uV 0 0020 10 m 0 0070 10 nA 0 006 PLC 100 us 100 us 575 0 0050 4 uV 0 0050 10 mQ 0 0100 15 nA 0 002 PLC 40 us 40 us 3 5 0 0050 4 uV 0 0050 10 mQ 0 0100 15 nA 0 001 PLC 20 us 20 us 42 4 0 0100 4 uV 0 0150 10 mQ 0 0150 30 nA ul Requires the digitizing option Option DIG Ms dataTec For DCV on the 10 V range with zero volts input and auto zero on RMS noise adder for both the 34465 and the 34470 Measured with zero volts input and auto Zero on The following DCI ranges have these additional multipliers
11. 3446LANU 3446ACCU 3446DIGU 3446MEMU Option at purchase GPB SEC LAN ACC DIG MEM 754 N A Accessories Accessories included 34400A 34461A 34405A 34470A Power cord Calibration certificate 34138A test lead set with probes fine tip probes SMT grabbers and mini grabber attachments Power cord IO Libraries CD USB cable Calibration certificate Accessories available 11059A 11060A 11062A 34131A 34133A 34134A 34136A 34138A 34151A 34152A 34153A 34162A 34171B 34172B 34330A E2308A YASA 21 W dataTec Kelvin probe set Applicable models All All 34460A 34460A 34465 70A 34465 70A All surface mount device probe Kelvin clip set Transit case Precision electronic test leads DC coupled current probe High voltage probe Test lead set Three signal wedge probe kit PT100 RTD 4 Wire Class A sensor kit PT100 RTD 4 Wire Class sensor elements Accessory pouch Input terminal block Calibration short 30 A current shunt Thermistor temperature probe Low thermal external digital multimeter scanning kit Description Add GPIB interface user installable Enable NISPOM and file security Enable LAN interface and external triggering Add 34138A accessory kit includes test leads USB cable Enable high speed digitizing and advanced triggering Enable 2 million readings memory Certificate of calibration ANSI NCSL 7540 3 2006 Definitions Specification spec
12. 50 kHz 50 100 kHz 100 300 kHz Resistance Test current 1000 1 mA 1 kQ 1 mA 10 KQ 100 pA 100 KQ 10 pA 1 MQ O uA 10 MQ 500 nA 100 MO 500 nA 10 MO DC current Burden voltage 100 pA lt 0 011 V 1 mA lt 0 11 V 10 mA lt 0 05 V 100 mA DON 1A lt 0 7 V JA lt 2 0V 10 A lt 0 5 V Capacitance 1 0000 nF 10 000 nF 100 00 nF 1 0000 uF 10 000 uF 100 00 uF E dataTec Ferdinand Lassalle Str 52 24 hours Tea 1 C 0 0030 0 0030 0 0020 0 0006 0 0015 0 0004 0 0020 0 0006 0 0020 0 0006 1 00 0 02 0 35 0 02 0 04 0 02 0 10 0 04 0 55 0 08 4 00 0 50 0 0030 0 0030 0 0020 0 0005 0 0020 0 0005 0 0020 0 0005 0 002 0 001 0 015 0 001 0 300 0 010 0 010 0 020 0 007 0 006 0 007 0 020 0 010 0 004 0 050 0 006 0 180 0 020 0 050 0 010 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 50 10 info datatec de 90 days Tea 9 C 0 0040 0 0035 0 0030 0 0007 0 0020 0 0005 0 0035 0 0006 0 0035 0 0010 1 00 0 03 0 35 0 03 0 05 0 03 0 11 0 05 0 60 0 08 4 00 0 50 0 008 0 004 0 008 0 001 0 008 0 001 0 008 0 001 0 008 0 001 0 020 0 001 0 800 0 010 0 040 0 025 0 030 0 006 0 030 0 020 0 030 0 005 0 080 0 010 0 200 0 020 0 120 0 010 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40
13. ACV range Specifications are for 1 second gate time 7 digits Specifications are for using Math Null zeroing High dissapation factor capacitors may show different results than a single frequency measurement Film capacitors usually have lower dissapation factors than other dielectrics The second burden voltage can be obtained by using the 10 A input range 13 E datafec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de www datatec de specifications 344 0A 34470A accuracy specifications of reading of range DC voltage and resistance Automatic calibration ACAL capable Range 24 hours Tacay 1 C DC voltage 100 mV 0 0030 0 0030 1V 0 0010 0 0004 10V 0 0008 0 0002 100 V 0 0020 0 0006 1000 V 0 0020 0 0006 Resistance 1000 0 0030 0 0030 1 KO 0 0020 0 0005 10 KO 0 0020 0 0005 100 KO 0 0020 0 0005 1 MO 0 0020 0 0005 10 MO 0 010 0 001 100 MO 0 100 0 001 1000 MQ 2 000 0 001 Range DC current 1 WA typ 10 uA typ 100 pA typ 1 mA 10 mA 100 mA 1A JA 104 Continuity 1 KO Diode test 5 V DC DC ratio typ 14 is dataTec 90 days Trea 59 C 0 0040 0 0035 0 0015 0 0004 0 0013 0 0002 0 0032 0 0006 0 0032 0 0006 0 0050 0 0040 0 0030 0 0005 0 0030 0 0005 0 0030 0 0005 0 0060 0 0005 0 020 0 001 0 200 0 001 2 000 0 001 24 hours 2
14. Ihrer taglichen Arbeit an Die dataTec Akademie halt Ihr Wissen zu vielen Bereichen der Messtechnik stets auf dem neuesten Stand Nutzen Sie unser vielfaltiges Seminarangebot mit renommierten Dozenten und transportieren Sie aktuelles Wissen in Theorie und Praxis in Ihre tagliche Arbeit Modernste Raumlichkeiten und bes te technische Ausstattung um das Erlebnis Wissen angenehm und komfortabel zu begleiten Unsere Seminarthemen Thermografie Labormesstechnik Pr fger te VDE EMV HF Messtechnik m Oszilloskope UVM Alle aktuellen Termine und Preise unter www datatec akademie de a dataTec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 515050 Fax07121 51 50 10 akademie datatec de www datatec akademie de
15. The 10 mA by 5x the 100 mA by 2x and the 10 A by 1 6x Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 5010 info datatec de www datatec de System speeds nom DC voltage DC current resistance 34460A 34461A 34465A 34470A Autorange time lt 30 ms lt 30 ms lt 5 ms Maximum internal trigger rate 300 s 1000 s 5 000 s Maximum external trigger rate 300 s 1000 s 5 000 s ASCII readings to bus 300 s 1000 s 40 000 s GPIB 8 000 s Single reading transaction rate 50 s 150 s 250 s AC voltage AC current Autorange time 10 s 10 s lt 5 ms Maximum internal trigger rate 50 s 50 s 250 s Maximum external trigger rate 50 s ogs 250 5 ASCII readings to bus 50 s 50 s 250 s Single reading transaction rate 50 s 50 s 200 s Frequency period Autorange time 10 s 10 s lt 5ms Maximum internal trigger rate 80 s 80 s 800 s Maximum external trigger rate 80 s 80 s 800 s ASCII readings to bus 80 s 80 s 900 s Single reading transaction rate 50 s 50 s 200 s 1 0 02 NPLC delay 0 autozero off math off and display off 2 These rates apply to all I O interfaces 3 Time to automatically change one range and be ready for new measurement lt 10 V lt 10 MQ 4 Includes measurement and IO time assumes connection via SOCKETS VXI 11 connections may be slower 5 Fast AC filter delay O math off and display off 6 10 ms aperture fast AC filter delay 0 math off and display off
16. characteristics and thermal EMF of connections Keysight recommends the use of PTFE or other high impedance low dielectric absorption wire Insulation for these measurements To maintain low thermal EMF connectors and wires made of copper are recommended Tel 07121 51 5050 Fax 07121 51 5010 info datatec de For power line frequency 0 1 For power line frequency 1 the NMR is 40 dB For 3 use 30 dB www datatec de Operating Characteristics for all models except where noted Performance versus measurement speed For DC voltage DC current and resistance 34460A amp 34461A 34460A 34461A Integration time Digits Readings s Digits Readings s Additional noise error 100 PLC 1 67 s 2 s 6 0 6 0 5 6 0 6 0 5 0 of range 10 PLC 167 ms 200 ms 6 6 5 6 6 5 0 of range 1 PLC 16 7 ms 20 ms 5M 60 50 5M 60 50 0 001 of range 0 2 PLC 3 ms 3 ms 5M 100 5M 300 0 001 of range 0 02 PLC 300 us 300 us 3 300 Ah 1000 0 01 of range AC voltage AC current Digits ACV ACI AC filter 6 A s 6 s Slow 6 1 6 s 4 s Medium 6 40 s 40 s Fast 6 50 s B0 Fast Frequency period Aperture Digits Readings 1 second 7 1 0 1 second 6 10 0 01 second 5 80 1 Reading speeds for 60 Hz and 50 Hz operation autozero off fixed range Add 5 nA for the 100 uA range add 0 2 uA for the 10 mA range Add 20 uV for DCV and 20 mQ for resistance Add 0 2 uA for DC current 10x the above range error for the
17. sinewave input gt 1 of range and gt 10 UA AC 10 Specifications are for the voltage measured at the input terminals The 1 mA test current is typical Variation in the current source will create some variation in the voltage drop across a diode junction 11 Actual measurement range and probe errors will be limited by the selected probe Probe accuracy adder includes all measurement and ITS 90 temperature conversion errors PT100 Ro settable to 100 0 5 Q to remove the initial probe error 12 Specifications are for 60 minute warm up and sine wave input unless stated otherwise Specifications are for 1 second gate time 7 digits 13 Applies to sine and square inputs gt 100 mV For 10 mV to lt 100 mV inputs multiply of reading error x10 14 Amplitude 10 120 of range and less than 750 ACV 15 Square wave input specified for 10 300 kHz 10 a dataTec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de www datatec de specifications 34465A 34465A accuracy specifications of reading of range DC voltage and resistance Automatic calibration ACAL capable Range 24 hours Taca 1 C DC voltage 100 mV 0 0030 0 0030 Ty 0 0015 0 0004 10 V 0 0010 0 0003 100 V 0 0020 0 0006 1000 V 0 0020 0 0006 Resistance 1000 0 0030 0 0030 1 KQ 0 0020 0 0005 10 KQ 0 0020 0 0005 100 KQ 0 0020 0 0005 1 MO 0 0020 0 0005 10 MQ 0 010 0
18. 0 0 40 0 10 0 070 0 030 0 006 0 005 0 004 0 1 second 1 ppm 0 100 0 030 0 020 0 004 0 000 1 year Tea 9 C 0 50 0 02 0 10 0 02 0 05 0 02 0 07 0 03 0 15 0 05 1 00 0 1 0 10 0 04 0 10 0 04 0 23 0 04 0 23 0 04 0 15 0 04 0 15 0 04 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 070 0 030 0 007 0 007 0 006 0 01 second 10 ppm 0 160 0 160 0 200 0 030 0 000 2 years Tea 9 C 0 50 0 02 0 11 0 02 0 06 0 02 0 08 0 03 0 15 0 05 1 00 0 1 0 10 0 04 0 10 0 04 0 23 0 04 0 23 0 04 0 15 0 04 0 15 0 04 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 070 0 030 0 010 0 009 0 008 0 001 second 100 ppm 0 160 0 160 0 200 0 240 0 003 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 50 10 info datatec de Temperature coefficient C 0 010 0 003 0 008 0 003 0 007 0 003 0 010 0 005 0 060 0 008 0 200 0 020 0 015 0 006 0 030 0 006 0 015 0 006 0 030 0 006 0 015 0 006 0 030 0 006 0 054005 0 05 0 01 0 05 0 01 0 05 0 01 0 05 0 01 0 05 0 01 0 0002 0 0002 0 0002 0 0002 0 0002 www datatec de specifications 34465A DC and AC current burden voltage at full scale DC current range Burden voltage 1 uA lt 0 0011 V 10 uA lt 0 011 V 100 uA lt O 11V 1 mA lt 0
19. 001 100 MQ 0 100 0 001 1000 MO 2 000 0 001 Range DC current 1 pA typ 10 pA typ 100 pA typ 1 mA 10 mA 100 mA 1A SA 10 A Continuity 1 KQ Diode test 5 V DC DC ratio typ 1 Me dataTec Ferdinand Lassalle Str 52 90 days Taca 2 C 0 0040 0 0035 0 0025 0 0004 0 0020 0 0004 0 0035 0 0006 0 0035 0 0006 0 0050 0 0040 0 0030 0 0005 0 0030 0 0005 0 0030 0 0005 0 0060 0 0005 0 020 0 001 0 200 0 001 2 000 0 001 24 hours Unies Ul 0 007 0 005 0 007 0 002 0 007 0 001 0 007 0 003 0 007 0 020 0 010 0 004 0 050 0 006 0 180 0 020 0 050 0 010 0 002 0 010 0 002 0 010 normalized input accuracy normalized reference accuracy 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 50 10 info datatec de 1 year Trea 2 C 0 0050 0 0035 0 0035 0 0004 0 0030 0 0004 0 0040 0 0006 0 0040 0 0006 0 0060 0 0040 0 0040 0 0005 0 0040 0 0005 0 0040 0 0005 0 0070 0 0005 0 025 0 001 0 300 0 001 3 000 0 001 90 days ees oe 0 030 0 005 0 030 0 002 0 030 0 001 0 030 0 005 0 030 0 020 0 030 0 005 0 070 0 010 0 200 0 020 0 120 0 010 0 008 0 020 0 008 0 010 2 years Taca 2 C 0 0065 0 0035 0 0050 0 0004 0 0045 0 0004 0 0055 0 0006 0 0055 0 0006 0 0070 0 0040 0 0050 0 0005 0 0050 0 0005 0 0050 0 0005 0 0080 0 0005 0 030 0 001 0 400 0
20. 020 0 0020 0 0020 0 0005 0 0050 0 0010 0 0050 0 0020 0 0050 0 0010 0 05 40 05 0 05 0 01 0 05 0 01 0 05 0 01 0 05 0 01 0 05 0 01 www datatec de specifications 34461A Range frequency 24 hours 90 days 1 year 2 years Temperature Tea 1 C Ia SE sc en coefficient C True RMS AC current gt Burden voltage 100 uA I mA 10 mA and lt 0 011 lt 0 11 lt 0 05 lt 0 5 V 100 mA ranges 3 Hz 5 kHz 0 10 0 04 0 10 0 04 0 10 0 04 0 10 0 04 0 015 0 006 5 10 kHz typ 0 10 0 04 0 10 0 04 0 10 0 04 0 10 0 04 0 030 0 006 1 A range lt 0 V 3 Hz 5 kHz 0 10 0 04 0 10 0 04 0 10 0 04 0 10 0 04 0 015 0 006 5 10 kHz typ 0 10 0 04 0 10 0 04 0 10 0 04 0 10 0 04 0 030 0 006 3 Arange lt 2 0V 3 Hz 5 kHz 0 23 0 04 0 23 0 04 0 23 0 04 0 23 0 04 0 015 0 006 5 10 kHz typ 0 23 0 04 0 23 0 04 0 23 0 04 0 23 0 04 0 030 0 006 10 A range Son 3 Hz 5 kHz 0 15 0 04 0 15 0 04 0 15 0 04 0 15 0 04 0 015 0 006 5 10 kHz typ 0 15 0 04 0 15 0 04 0 15 0 04 0 15 0 04 0 030 0 006 Continuity 1 kQ 0 002 0 030 0 008 0 030 0 010 0 030 0 012 0 030 0 0010 0 0020 Diode test 5V 0 002 0 030 0 008 0 030 0 010 0 030 0 012 0 030 0 0010 0 0020 DC ratio typ normalized input accuracy normalized reference accuracy Temperature PT100 DIN IEC 751 Probe accuracy 0 05 C 5 KO thermistor Probe accuracy 0 1 C Frequency specifica
21. 1098 VOC DIV 50 AC A Pin ORT NAT Pies ACE 34461 65 70A DMM rear panel with GPIB option installed 19 E datafec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de www datatec de 20 W General Characteristics for all models except where noted Line power Power supply Power line frequency Power consumption Environment Operating environment Operating altitude storage temperature Mechanical Rack dimensions Bench dimensions Weight Regulatory Safety CE ISM 1 A Be EMC Acoustic noise nominal Triggering conditions External input Delay Jitter Minimum pulse width Maximum rate Voltmeter complete output Polarity Pulse width Computer interfaces LXI rev 1 4 dataTec 100 120 127 220 230 240 ACV 10 CAT II 00 60 400 Hz 10 25 VA Full accuracy for 0 to 55 C Full accuracy to 80 R H at 40 C non condensing Up to 3 000 m 40 to 70 C W x H x D 212 8 mm x 88 3 mm x 272 3 mm W x H x D 261 2 mm x 103 8 mm x 303 2 mm 34460A 3 68 kg 8 1 lb 34461 65 70A 3 76 kg 8 3 Ib EN 61010 1 2010 3rd Edition ANSI ISA 61010 1 82 02 01 Third Edition ANSI UL 61010 1 Third Edition CAN CSA C22 2 No 61010 1 Third Edition EN 61010 2 030 2010 1st Edition ANSI ISA 61010 2 030 82 02 03 First Edition ANSI UL 61010 2 030 First Edition CAN CSA C22 2 No 61010 2 030 First Editio
22. 11 V 10 mA lt 0 027 V 100 mA lt 0 27V 1A lt 0 7 V 0 05 V 7 3A lt 2 0 V 0 15 V 7 10A lt 05V Digitizing Typical performance for these conditions Sample rate 50 kHz Aperture 20 uS Sine wave input Vpeak Full scale of range Input frequency 1 kHz 10 kHz Function range Spur free range THD noise BW 3 db SFDR SNDR DCV 0 1 1 V 79 60 15 57 15 kHz DCV 10 V 86 59 82 58 15 kHz DCV 100 1000 V 64 42 60 42 15 kHz DCI 0 1 1 mA 78 62 75 60 10 kHz DCI 10 100 mA 78 62 67 60 10 kHz DCI 1 10 A 65 49 63 48 10 kHz 1 Specifications are for 60 minute warm up integration setting of 10 or 100 NPLC auto zero on AC slow filter ACAL run within the last 2 days 2 20 over range on all ranges except 1000 DCV 750 ACV 10 DCA 3 DCA 10 ACA 3 ACA and diode test have 0 3 Relative to calibration standards 5 The 10Arange is only available on a separate front panel connector Add 2 mA per amp for inputs greater than 5 Arms 6 Add this for each C outside TCAL 5 C 7 Add this for each C outside the last ACAL 2 C 8 Add this for each C outside TCAL 2 C 9 Specifications are for 4 wire ohms function or 2 wire ohms using math null for offset Without math null add 0 2 Q additional error in 2 wire ohms function 11 12 le 14 15 The 100 M and 1 G ohm ranges are 2 wire only See the manual for low power ohms specification and measurement currents For each additional volt over 500 V add 0 02 mV of error
23. 50 0 02 0 11 0 02 0 06 0 02 0 08 0 03 0 15 0 05 1 00 0 1 0 10 0 04 0 10 0 04 0 23 0 04 0 23 0 04 0 15 0 04 0 15 0 04 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 070 0 030 0 010 0 009 0 008 0 001 second 100 ppm 0 160 0 160 0 200 0 240 0 003 Temperature coefficient C 0 010 0 003 0 008 0 003 0 007 0 003 0 010 0 005 0 060 0 008 0 200 0 020 0 015 0 006 0 030 0 006 0 015 0 006 0 030 0 006 0 015 0 006 0 030 0 006 0 05 0 05 0 05 0 01 0 05 0 01 0 05 0 01 0 05 0 01 0 05 0 01 0 0002 0 0002 0 0002 0 0002 0 0002 www datatec de Specifications 344 0A DC and AC current burden voltage at full scale DC current range Burden voltage 1 uA lt 0 0011 V 10 pA lt 0 011 V 100 uA lt 0 11 V 1 mA lt 0 11 V 10 mA lt 0 027 V 100 mA 27V TA lt 07 W0 05V 3A C20 W013 yV 10A USW Digitizing Typical performance for these conditions Sample rate 50 kHz Aperture 20 uS sine wave input Vpeak Full scale of range Input frequency 1 kHz 10 kHz Function range Spur free range THD noise BW 3 db SFDR SNDR DCV 0 1 1 V 79 60 75 57 15 kHz DCV 10 V 86 59 82 58 15 kHz DCV 100 1000 V 64 42 60 42 15 kHz DCI 0 1 1 mA 78 62 75 60 10 kHz DCI 10 100 mA 78 62 67 60 10 kHz DCI 1 10 A 65 49 63 48 10 kHz 1 Specifications are
24. A 16 ppm 5 000 rdgs s std 50 000 rdgs s opt 50 000 rdgs std 2 million rdgs opt 100 mV to 1 000 V 1 uA to 10 A 100 uA to 10 A 100 Q to 1 000 MQ 1 OV 3 Hz to 300 kHz RTD P1T100 thermistor thermocouples 1 0 nF to 100 0 uF Yes Color graphical Histogram bar chart trend chart Yes Yes Yes Optional www datatec de 3 Bar meter mode provides the number display along with an analog meter to provide a visual view of your measurements Number mode provides the traditional digits view of measurements a Auto 100m Measure with Unquestioned Truevolt Confidence Worry about the quality of your design not the quality of your measurements In a rack or on a bench real world signals are never flat They have some level of AC signal riding on top from power line noise other environmental noise or injected current from the meter itself How well your meter deals with these extraneous factors and eliminates them from the true measurement makes a big dif ference to your accuracy Behind the scenes Keysight s Truevolt technology accounts for measurement errors created by these real world factors so you can be confident in your measurements and it is only available on Keysight DMMs Truevolt technology starts with an analog to digital converter that enables a patented metrology grade architecture Using this architecture Keysight delivers agood balance of measurement resolution l
25. V and 750 V ranges 3 5 Hz 5 10 Hz 10 Hz 20 kHz 20 50 kHz 50 100 kHz 100 300 kHz True RMS AC current 7 100 pA 1 mA 10 mA 100 mA 1 A ranges 3 Hz 5 kHz 5 kHz 10 kHz typ 3 A range 3 Hz 5 kHz 5 kHz 10 kHz typ 10 A range 3 Hz 5 kHz 5 kHz 10 kHz typ Capacitance 1 0000 nF 10 000 nF 100 00 nF 1 0000 uF 10 000 uF 100 00 uF Frequency 100 mV 1 V 10 V 100 V and 750 V ranges 7 3 10 Hz 10 100 Hz 100 Hz 1 kHz 1 300 kHz Square wave 18 20 Additional frequency errors of reading 8 Aperture resolution range 3 40 Hz 40 100 Hz 100 Hz 1 kHz 1 300 kHz Square wave 12 a dataTec Ferdinand Lassalle Str 52 Probe accuracy 0 05 C Probe accuracy 0 1 C Probe accuracy reference junction accuracy 0 3 C Probe accuracy reference junction accuracy 0 5 C 24 hours Tea 1 C 0 50 0 02 0 10 0 02 0 02 0 02 0 05 0 03 0 15 0 05 1 00 0 1 0 07 0 04 0 10 0 04 0 23 0 04 0 23 0 04 0 10 0 04 0 15 0 04 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 070 0 030 0 003 0 002 0 001 1 second 0 1 ppm 0 O O O o amp 90 days Tea 9 C 0 50 0 02 0 10 0 02 0 04 0 02 0 06 0 03 0 15 0 05 1 00 0 1 0 09 0 04 0 10 0 04 0 23 0 04 0 23 0 04 0 15 0 04 0 15 0 04 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 1
26. a E MESSBAR MEHR KEYSIGHT Ihr Spezialist f r datalec TECHNOLOGIES Mess und Pr fger te Autorisierter Distributor Keysight Technologies Digital Multimeters 34460A 34461A 34465A 6 digit 34470A 7 digit Data Sheet SIGHT 34470A 710 Digit Multimeter Fusvol ni WAAR VERAN MEKKA WARAN PELAGE tnt KEK W 1 o i Kd Truevolt DMMs for your next generation of insights E mE dataTec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de www datatec de 2 Key specifications Digits of resolution Basic DCV accuracy Max reading rate Memory Measurements DCV ACV DCI ACI 2 and 4 wire resistance Continuity diode Frequency period Temperature Capacitance Dual line display Display Statistical graphics Rear input terminals lO interface USB LAN LXI Core GPIB a dataTec Get more insight quickly Truevolt DMM s graphical capabilities such as trend and histo gram charts offer more insights quickly Both models also provide a data logging mode for easier trend analysis and a digitizing mode for capturing transients Measure low power devices The ability to measure very low current 1 UA range with pA resolution allows you to make measurements on very low power devices Maintain calibrated measurements Auto calibration allows you to compensate for temperature drift so you can maintain measurement accu
27. al trigger delay External trigger jitter Volatile reading memory Probe hold Capture and navigate stable list of readings Internal flash file system 80 MB total capacity Save reading memory to non volatile memory in CSV format Store and recall user defined states power off state and preference files Save screen captures in BMP or PNG formats 1 to 1 000 000 0 to 3600 sec 1 us step size lt 10 us lt 1 us DC fixed range 10 000 34461A 1 000 34460A 1 Power off state only when power down is initiated via front panel power switch Math functions Per function null min max avg Sdev dB dBm span count limit test histogram Display 4 3 color TFT WQVGA 480x272 with LED backlight Supports basic number bar meter trend chart 34461A only histogram views User defined power on message display label and selectable screen colors Integrated context sensitive system help through press and hold buttons Real time clock calendar Set and read year month day hour minute seconds Note seconds not set table Battery CR 2032 coin type replaceable gt 10 year life typ Software available lO Libraries www keysight com find lOLibraries BenchVue www keysight com find benchvue www datatec de KEYSIGHT TECHNOLOGIES Autorisierter Distributor Ihr Spezialist f r Mess und Pr fger te Options Upgrades amp Accessories Options amp Upgrades Upgrades post purchase 3446GPBU 3446SECU
28. fication of reading 100 mV 1 V 10 V 100 V and 750 V ranges 3 10 Hz 0 100 0 100 0 100 0 100 0 0002 10 100 Hz 0 030 0 030 0 030 0 035 0 0002 100 Hz 1 kHz 0 030 0 010 0 012 0 017 0 0002 1 300 kHz 0 002 0 008 0 012 0 017 0 0002 Square wave 0 001 0 008 0 012 0 017 0 0002 Additional gate time errors of reading 1 gt 1 Frequency 1 second 0 1 second 0 01 second 3 40 Hz 0 0 200 0 200 40 100 Hz 0 0 060 0 200 100 Hz 1 kHz 0 0 020 0 200 1 300 kHz 0 0 004 0 030 Square wave 0 0 0 ee ee ee 11 12 la 14 15 s W For DC Specifications are for 60 minute warm up aperture of 10 or 100 NPLC and auto zero on For AC Specifications are for 60 minute warm up slow AC filter sine wave 20 overrange on all ranges except 1 000 V DCV 750 ACV 3A AC and diode test Relative to calibration standards Add this for each C outside Tea 5 C Specifications are for sine wave input gt 0 3 of range and gt 1 mVrms 750 ACV range limited to 8 x 107 Volt Hz Low frequency performance three filter settings are available 3 Hz 20 Hz 200 Hz Frequencies greater than these filter settings are specified with no additional errors Specifications are for 4 wire ohms function or 2 wire ohms using math null for offset Without math null add 0 2 Q additional error in 2 wire ohms function Specifications are for sinewave input gt 1 of range and gt 10 uA AC Specifications are for the voltage measured at
29. for 60 minute warm up integration setting of 10 or 100 NPLC auto zero on AC slow filter ACAL run within the last 2 days 2 20 over range on all ranges except 1000 DCV 750 ACV 10 DCA 3 DCA 10 ACA 3 ACA and diode test have 0 3 Relative to calibration standards 5 The 10 A range is only available on a separate front panel connector Add 2 mA per amp for inputs greater than 5 Arms 6 Add this for each C outside TCAL 5 C 7 Addthis for each C outside the last ACAL 2 C 8 Add this for each C outside TCAL 2 C 9 Specifications are for 4 wire ohms function or 2 wire ohms using math null for offset Without math null add 0 2 Q additional error in 2 wire ohms function 12 13 14 15 The 100 M and 1 G ohm ranges are 2 wire only See the manual for low power ohms specification and measurement currents For each additional volt over 500 V add 0 02 mV of error Specifications are for the voltage measured at the input terminals The 1 mA test current is typical Variation in the current source will create some variation in the voltage drop across a diode junction See user manual for details Actual measurement range and probe errors will be limited by the selected probe Probe accuracy adder includes all measurement and ITS 90 temperature conversion errors PT100 Ro settable to 100 Q 5 Q to remove the initial probe error The internal reference junction uses the U1180A or equivalent adapter This has a typical per
30. formance of 1 0 C This internal reference junction can be adjusted for better accuracy An external reference junction can also be used Specifications are for sinewave input gt 0 3 of range and gt 1 mVrms 750 ACV range limited to 8 x 10 Volt Hz For each additional volt over 300 Vrms add 1 mVrms of error Low frequency performance three filter settings are available 3 Hz 20 Hz 200 Hz Frequencies greater than these filter settings are specified with no additional errors Specifications are for sinewave input gt 1 of range and gt 10 Arms Specifications are for sine wave input unless stated otherwise Square wave input specified for 10 300 kHz for 1 second aperature For shorter aperatures the minimun frequency requires gt 2 cycles Input gt 100 mV For 10 mV to 100 mV inputs multiply of reading error x10 Amplitude 10 120 of range except 14 100 for the 750 ACV range Specifications are for 1 second gate time 7 digits Specifications are for using Math Null zeroing High dissapation factor capacitors may show different results than a single frequency measurement Film capacitors usually have lower dissapation factors than other dielectrics The second burden voltage can be obtained by using the 10 A input range 16 E E datafec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 50 10 info datatec de www datatec de Measurement Characteristics for all models except whe
31. ges Gate time Measurement considerations Autozero OFF operation Normal mode rejection 60 dB 0 db Reciprocal counting technique Measurement is AC coupled using AC measurement functions 100 mVrms full scale to 750 Vrms Auto or manual ranging 1 ms 34465 70A 10 ms 100 ms or 1s All frequency counters are susceptible to error when measuring low voltage low frequency signals Shielding inputs from external noise pickup Is critical for minimizing measurement errors Following instrument warm up at a stable ambient temperature 1 C and lt 10 minutes Add 0 0002 of range 5 uV for DCV or 5 mQ for resistance Measurement settling considerations High power settling Applying high power signals more than 300 Vrms 500 VDC 1A DC or 1 Arms can cause self heating in the signal conditioning components These errors are included in the instrument specifications Internal temperature changes due to self heating may cause additional error on other functions or ranges The additional error will generally dissipate within a few minutes DC blocking capacitor Errors will occur in ACV and Frequency functions when attempting to measure an input following a DC offset voltage change The input blocking RC time constant must be allowed to fully settle up to 1 second before the most accurate measurements are possible External connections Reading settling times are affected by source impedance cable dielectric
32. he measurement terminals of your DMM In real measurement situations there are always input currents creating additional measurement errors Truevolt DMMs take care of input bias current Some alternative DMMs offer 20 to infinitely poorer performance some are too noisy to measure 60 50 Input 40 WER current 3 30 too noisy 20 to measure Truevolt Brand A Brand B Brand C Digital AC rms measurements For meters in this class only Keysight uses digital direct sampling techniques to make AC rms measurements This results in a true rms calculation technique that avoids the slower response of analog RMS converters used in all other vendor s 6 digit DMMs This allows for crest factors up to 10 without additional error terms This is a unique patented technique only used by Keysight Peak value RMS value Crest factor the ratio of the peak value to the RMS value of a waveform AC measurement accuracy is degraded when signals have energy contained in higher frequencies than a typical sine wave a dataTec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de You can measure your real world signals with confidence All Truevolt DMM specifications are tested and guaranteed for compliance with ISO IEC 17025 standards so you can prove the effectiveness of your lab or production line s quality management system Many lower cost DMM
33. inearity accuracy and speed at a value price all de rived and guaranteed per ISO IEC 17025 industry standards a dataTec 1 39m 220p 950 Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de Histogram mode gives you a Statistical view of your measurements 691 225m 691 315m 691 405m www datatec de BenchVue software for the PC makes it simple to connect control capture and view Keysight s DMMs simultaneously with other Keysight bench instruments with no additional programming correlate measurement activities and obtain actionable insights 468 741 mVdc Visualize multiple measurements simultaneously a i Easily log data screen shots and system state me Rapidly prototype custom test sequences Recall past state of your bench to replicate results Export measurement data in desired format fast Quickly access manuals drivers FAQs and videos Monitor and control bench from mobile devices The Digital Multimeter App within BenchVue enables control of digital multimeters to visualize measurements perform data logging and annotate captured data included in model BVO000A Upgrading to the Pro version model BVO001A provides histograms digitizer capability and unrestricted data 0 o E 123 957 mVdc logging with limit checking and alerts Benefit from a new perspective by visualizing multiple DMM s at the same time Display si
34. n Refer to Declaration of Conformity for current revisions Measurement Category Il to 300 V Other non MAINS circuits to 1 000 Vpk Pollution Degree 2 IEC 61326 EN 61326 CISPR ICES 001 AS NZS 2064 1 Refer to Declaration of Conformity for current revisions 35 dBA Low power I TL compatible input programmable edge triggered lt 1 US lt 1 us 1 us Up to 1 kHz 34461A up to 300 Hz 34460A 3 3 V logic output Programmable edge pulse Approximately 2 us 10 100Base T Ethernet Sockets VXI 11 protocol Web user interface Optional on 34460A Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 50 10 info datatec de USB USB 2 0 USB TMC488 amp MTP protocol GPIB Optional GPIB IEEE 488 Language SCPI 1999 IEEE 488 2 34401A compatible Front panel USB host port Supports USB 2 0 high speed mass storage MSC class devices Capability import export instrument configuration files save volatile readings and screen captures un Ten Q2 D o55555 L 212 8 mm I DR Er A CAUSA SUSU AAU 272 3 mm id System speeds nom Benchmark GPIB USB 2 0 VXI 11 Sockets Function change 50 s 50 s 50 s 50 s Range change 100 s 100 s 100 s 100 s 1 Rate to change from 2 wire resistance to any other function 2 Rate to change from one range to the next higher range lt 10 V lt 10 MQ Triggering and memory samples per trigger Trigger delay Extern
35. ngle measurements charts tables or histograms from a single instrument or multiple DMMs simultaneously to correlate trends you might otherwise miss Record measurements and export results in a few clicks Log and export data quickly to popular tools such as Microsoft Excel Microsoft Word and MATLAB for documentation or further analysis Access and control tests on your DMM remotely With the companion BenchVue Mobile app monitor and respond to long running tests from anywhere Download BenchVue software at no cost today 1 One hour limit in no cost version dataTec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de Figure 1 See your measurements across instruments in one place to quickly Figure 2 BenchVue enables control of your DMM to data log and visualize www keysight com find benchvue measurements in a wide array of display options www datatec de 5 Measure with Unquestioned Truevolt Confidence What Truevolt technology means to you You can measure your real world signals not instrument error Noise and injected current Keysight Truevolt DMMs contribute less than 30 of the injected current than alternatives Compared to some lower cost alternatives Truevolt DMMs offer almost 100 less noise 800 700 600 500 lt 400 300 200 100 Truevolt Brand A Brand B Brand C Input bias current Ideally no current flows into t
36. racy throughout your workday 34460A 6 79 ppm 300 rdgs s 1 000 rdgs 100 mV to 1 000 V 100 uAto3A 100 uAto3A 100 Q to 100 MQ Y 0 3 Hz to 300 kHz RTD PT100 thermistor 1 0 nF to 100 0 uF Yes Color graphical Histogram bar chart No Yes Optional Optional Keysight s NEW Truevolt Digital Multimeters DMMs offer a full range of measurement capabilities and price points with higher levels of accuracy speed and resolution 691 315m 691 405m M Range Aperture Auto zero Inpurz DCV Ratio Ciear a om Auto On Readings The bright 4 3 high resolution monitor is a prominent feature of Keysight s Truevolt DMM family Overview of Keysight Truevolt Digital Multimeters 34461A 6 35 ppm 1 000 rdgs s 10 000 rdgs 100 mV to 1 000 V 100 uA to 10 A 100 uA to 10 A 100 Q to 100 MQ Y oV 3 Hz to 300 kHz RTD PT100 thermistor 1 0 nF to 100 0 uF Yes Color graphical Histogram bar chart trend chart Yes Yes Yes Optional Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 34465A 6 30 ppm 5 000 rdgs s std 50 000 rdgs s opt 50 000 rdgs std 2 million rdgs opt 100 mV to 1 000 V 1 uA to 10 A 100 uA to 10 A 100 Q to 1 000 MQ wav 3 Hz to 300 kHz RTD PT100 thermistor thermocouples 1 0 nF to 100 0 uF Yes Color graphical Histogram bar chart trend chart Yes Yes Yes Optional Fax 07121 51 50 10 info datatec de 34470
37. re resolution range 3 40 Hz 40 100 Hz 100 Hz 1 kHz 1 300 kHz Square wave 15 a dataTec Ferdinand Lassalle Str 52 Probe accuracy 0 05 C Probe accuracy 0 1 C Probe accuracy reference junction accuracy 0 3 C Probe accuracy reference junction accuracy 0 5 C 24 hours Tea 1 C 0 50 0 02 0 10 0 02 0 02 0 02 0 05 0 03 0 15 0 05 1 00 0 1 0 07 0 04 0 10 0 04 0 23 0 04 0 23 0 04 0 10 0 04 0 15 0 04 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 070 0 030 0 003 0 002 0 001 1 second 0 1 ppm 0 oloOIloO oO 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 50 10 info datatec de 90 days Tea 9 C 0 50 0 02 0 10 0 02 0 04 0 02 0 06 0 03 0 15 0 05 1 00 0 1 0 09 0 04 0 10 0 04 0 23 0 04 0 23 0 04 0 15 0 04 0 15 0 04 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 070 0 030 0 006 0 005 0 004 0 1 second 1 ppm 0 100 0 030 0 020 0 004 0 000 1 year Tea 9 C 0 50 0 02 0 10 0 02 0 05 0 02 0 07 0 03 0 15 0 05 1 00 0 1 0 10 0 04 0 10 0 04 0 23 0 04 0 23 0 04 0 15 0 04 0 15 0 04 0 50 0 50 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 40 0 10 0 070 0 030 0 007 0 007 0 006 0 01 second 10 ppm 0 160 0 160 0 200 0 030 0 000 2 years Tea 9 C 0
38. re noted DC voltage Measurement method A D Linearity 34460 61A 34465A 34470A Input resistance 0 1 V 1 V 10 V range 100 V 1 000 V range Input bias current Input terminals Input protection True RMS AC voltage Measurement type Measurement method Maximum input Input impedance Input protection Keysight patented continuously integrating multi slope IV A D converter 0 0002 of reading 0 0001 of range 0 0001 of reading 0 0001 of range 0 00005 of reading 0 0001 of range Selectable 10 MQ or gt 10 GQ 10 MQ 1 lt 30 pA at 25 C Copper alloy 1 000 V on all ranges AC coupled True RMS Measures the AC component of the input Digital sampling with anti alias filter 400 DCV 1 100 Vpeak 1 MQ 1 in parallel with lt 100 pF 750 Vrms all ranges DC and True RMS AC current AC measurement type AC measurement method Input protection 3 A Input protection 10 A 34461 65 70A only Directly coupled to the fuse and shunt AC True RMS measurement measures the AC component only Digital sampling with anti alias filter Externally accessible 3 15 A 500 V fuse Replacement part number 2110 1547 3 15 A external fuse Internal 11 A 1 000 V fuse Replacement part number 2110 1402 11 A external fuse Internal 11 A 1000 V fuse Replacement part number 2110 1402 11 A external fuse AC crest factor and peak input Crest factor Peak input Overload ranging Resis
39. s in this class do not carry a guarantee of their measurement specifications You can take advantage of expanded measurement functionality Compared to the 34401A DMN Truevolt DMMs offer expanded current ranges from 100 uA to 10 A We have also added a temperature measurement function RTD PT100 5 kQ thermistor Additionally diode measurement capability has been expanded to allow a larger full scale voltage to be measured 5 V to enable the measurement of more diode types such as LEDs Fixed 104 Aperture Auto Zero 3A Off Terminals www datatec de Move to The Next Generation 34401A DMM with 100 Assurance Migrate with confidence Migration Q amp A QUESTION ANSWER Everything you depend on with the 34401A and more Program Will my existing programs still work VES ar mer ao A DMN ownee yourh compatibility if switch to the 3446145 A DMM and TN trust the ugs Measurements Will have the same performance so it YES it gives you Now with the Keysight doesn t affect the results on my line Truevolt 34461A DMM you can get all of the advantages of the 34401A and more Cost Will it cost the same to buy use YES Now you can get faster answers and have maintain and repair and potentially less since the even more confidence in your results DMMs now include a 3 year The best news of all You can migrate standard warranty from the 34401A to the 34461 A without a En hassle No need to rewrite your software Reliability M
40. t Technologies 2015 November 13 2015 5991 1983EN Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 50 10 info datatec de www datatec de a E MESSBAR MEHR E E Ihr Spezialist f r m ale Mess und Pr fgor te Milz Il 0 MESSBAR MEHR AUSWAHL MIT AKTUELLEN PREISEN PRODUKTHIGHLIGHTS UND ZUBEH R DER B2B ONLINESHOP STARKE MARKEN HOCHSTE PRODUKTVIELFALT BESTE QUALITAT Schnell und bequem online bestellen bei dataTec ist das m glich Bei uns finden Sie die perfekte L sung fur ihre vielfaltigen Anforderungen Wir bieten eine unschlagbare Auswahl an Mess und Prufgeraten namhafter Hersteller Diese reicht von Arbitr r Funktionsgeneratoren uber Logikanalysatoren bis hin zu Stromversorgungen und Stromzangen oder Oszilloskopen bis 90 GHz Bandbreite Hohe Lagerkapazitat und kurze Wege sorgen dafur dass die gewunschte Ware ganz schnell bei Ihnen ist Bundesweit meist innerhalb eines Tages Mehr Klicks mehr Vorteile Mehrere tausend Mess und Prufgerate Versandkostenfrei ab 80 Tagesaktuelle Preise und Promotions Datenblatt Download Warenkorbrabatt bei Onlinebestellung uvm Angebotsanfrage oder Bestellung unter www datatec de 22 E datafec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de www datatec de a E MESSBAR MEHR a Ihr Spezialist f r m ale Mess und Prufgerate da
41. ta ec MESSBAR MEHR BERATUNG KOSTENLOS UND UNVERBINDLICH AM TELEFON ODER VOR ORT DIE TECHNISCHEN EXPERTEN KOMPETENTE BERATUNG VOR UND NACH DEM KAUF Haben Sie eine technische Frage zu den Ger ten zum Handling und Bedienung eines Ger tes zur passenden Software und oder bei der Auswahl des richtigen Equipments f r Ihre Messaufgabe Bei uns k mmern sich echte Diplom Ingenieure Elektronik und Elektrotechniker mit langj hriger Praxiserfahrung und hoher Kompetenz um Ihr Anliegen Kostenlos ber t Sie unser praxiserfahrener und herstellerzertifizierter Au endienst direkt bei Ihnen vor Ort und oder f hrt Ihnen live das ge w nschte Mess und Pr fger t vor Die technischen Experten f r m Oszilloskope m Thermografie Temperatur Spektrum Netzwerkanalysatoren m Pr fger te VDE Netzanalyse m Netzger te Stromversorgungen UVM Technische Frage oder Termin vereinbaren unter 07121 515050 23 E E datafec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de www datatec de a E MESSBAR MEHR datalec m AKADEMIE MESSBAR MEHR WISSEN FORT UND WEITERBILDUNGEN F R IHREN BERUFLICHEN ERFOLG DIE DATATEC AKADEMIE SEMINARE IN THEORIE UND PRAXIS Der Kauf von Mess oder Pr fger ten bei data Tec ist der erste Teil zur L sung Ihrer Messaufgabe Ist die Messtechnik beschafft oder bereits vorhanden steht das Thema Umsetzung in
42. tance Measurement method Maximum lead resistance 4 wire ohms Input protection Continuity diode test Response time Continuity threshold 17 W dataTec Ferdinand Lassalle Str 52 72770 Reutlingen 10 1 maximum crest factor 3 1 at full scale Measurement bandwidth limited to 300 kHz for signal plus harmonics 300 of range or maximum input Will select higher range if peak input overload is detected during auto range Overload is reported in manual ranging selectable 4 wire or 2 wire ohms Current source referenced to LO input 10 of range per lead for 100 Q 1 kQ ranges 1 KQ per lead on all other ranges 1 000 V on all ranges 300 samples s with audible tone Fixed at 100 l 2 DC ratio Measurement method Input HI LO Reference sense Input to reference sense Temperature Input HI LO reference sense HI LO 100 mV to 1000 V ranges HI Input LO 100 mV to 10 V ranges autoranged HI and LO reference sense terminals reference to LO input lt 12 V PT100 platinum RTD sensor a 0 003850 0 C DIN IEC 751 Measurement conversions limited to 200 to 600 C 5 KO thermistor B 3891 YSI 44007 or equivalent Measurement conversions limited to 80 to 150 C Measurement noise rejection 60 Hz 50 Hz for 1 kQ LO lead unbalance 500 V peak maximum DCV CMRR 140 dB ACV CMRR 70 dB Integration time 210 PLC CEPE Frequency and period Measurement method Voltage ran
43. the input terminals The 1 mA test current Is typical Variation in the current source will create some variation in the voltage drop across a diode junction Actual measurement range and probe errors will be limited by the selected probe Probe accuracy adder includes all measurement and ITS 90 temperature conversion errors PT100 Ro settable to 100 Q 5 Q to remove the initial probe error Specifications are for 60 minute warm up and sine wave input unless stated otherwise Specifications are for 1 second gate time 7 digits Applies to sine and square inputs 2 100 mV For 10 mV to lt 100 mV inputs multiply of reading error x10 Amplitude 10 120 of range and less than 750 ACV Square wave input specified for 10 300 kHz Specifications are for using Math Null zeroing High dissapation factor capacitors may show different results than a single frequency measurement Film capacitors usually have lower dissapation factors than other dielectrics dataTec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 50 50 Fax 07121 51 50 10 info datatec de www datatec de 9 Specifications 34461A 34461A accuracy specifications of reading of range These specification are compliant to ISO IEC 17025 for K 2 Range frequency DC voltage 100 mV 1V 10V 100 V 1000 V True RMS AC voltage 5 100 mV 1 V 10 V 100 V and 750 V ranges 3 b Hz 5 10 Hz 10 Hz 20 kHz 20
44. tion of reading 1 gt 3 100 mV 1 V 10 V 100 V and 750 V ranges 3 10 Hz 0 100 0 100 0 100 0 100 0 100 10 100 Hz 0 030 0 030 0 030 0 030 0 035 100 Hz 1 kHz 0 003 0 008 0 010 0 010 0 015 1 300 kHz 0 002 0 006 0 010 0 010 0 015 Square wave 0 001 0 006 0 010 0 010 0 015 Additional gate time errors of reading Frequency 1 second 0 1 second 0 01 second 3 40Hz 0 0 200 0 200 40 100 Hz 0 0 060 0 200 100 Hz 1 kHz 0 0 020 0 200 1 300 kHz 0 0 004 0 030 Square wave 0 0 0 For DC Specifications are for 60 minute warm up aperture of 10 or 100 NPLC and auto zero on For AC Specifications are for 60 minute warm up slow AC filter sine wave 2 20 over range on all ranges except 1 000 V DCV 750 ACV 10 ADC 3A AC 10 AAC and diode test 3 Relative to calibration standards 4 Add this for each C outside Toa 5 C 5 Specifications are for sinewave input gt 0 3 of range and gt 1 mVrms 750 ACV range limited to 8x 10 7 Volt Hz 6 Low frequency performance three filter settings are available 3 Hz 20 Hz 200 Hz Frequencies greater than these filter settings are specified with no additional errors 7 Specifications are for 4 wire ohms function or 2 wire ohms using math null for offset Without math null add 0 2 Q additional error in 2 wire ohms function 8 The 10 A range is only available on a separate front panel connector Add 2 mA base per amp or inputs gt 5A rms 9 Specifications are for
45. y 34401A never breaks Are the YES programs or spend hours learning a Truevolt DMMs going to be as good That s why we can offer brand new complicated interface a 3 year standard warranty tiseiyourexictneprourame Te Use Will we be able to use it easily Quickly YES DMM is the industry s only 100 drop in SCPl compatible replacement for the 34401A DMM Other DMMs may claim 34401A SCPI compatibility but only a subset of SCPI commands are implemented No long learning curve The Truevolt DMMs were designed by the same team that created the 34401A The team kept 34401A measurements reliability and familiarity in mind as they created the Truevolt family of DMMs So you can use it without spending hours learning how The 34461A represents everything you have known and trusted with your Keysight DMM measurements for decades it just keeps getting stronger For more information visit www keysight com find 34401Amigration gt a gt Mees EA unmeter Truevolt sat rand ei 2 Rae IHE 2 Is Y g ih a ED P d Bio Bh izil 2 q 681 27m Range Aperture Auto zero Input2 OCVRato Gilcar Off Auto 0 Readings 34461A The industry s only 100 drop in SCPl compatible replacement for the 34401A DMM E m dataTec Ferdinand Lassalle Str 52 72770 Reutlingen Tel 07121 51 5050 Fax 07121 51 50 10 info datatec de
Download Pdf Manuals
Related Search