TELEWELL ELECTRIC CO
Contents
1. SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 31 display shows BUSINESS MODE Standby Mode Code 32 In standby the telephone port will be connected directly to the telephone line and phones connected there will ring This feature allows you to leave the call blocker off whenever you like without disconnecting the device To enable this mode press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 32 display shows STANDBY MODE After Hours Mode Programmable Time Feature Introduction During a certain time of the day or night you can set the Call Blocker to enter into After Hours Mode This mode is designed to keep phones connected to the TEL phone port from ringing and allow calls to be answered by an optional answer machine when it is enabled on a daily basis If you run a business then you would use this After Hours Mode so all callers can leave a message If you work or dinner times are different from regularly scheduled times you would use this mode so that you can get your sleep or to completely avoid disruptive callers During After Hours Mode VIP callers can ring through at any time regardless of the After Hours time settings Invited callers can only ring through normally when After Hours Mode is not enabled The clock o2. for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code97 display shows ONLY VIP INVITE NOTE that when Code 97 is stored all calls will be Blocked answered and hungup on until you add Invited number When the prompt for ENTER CODE displays again enter Code 50 to store a 10 digit number maximum to 20 digit number 11 digits for Canada or Vonage then the key Example for individual numbers enter Code 50 002 123 4567 display shows NBR INVITED Store up to 30 sets of phone number including area codes WARNING This will delete all numbers from all lists To delete All numbers stored enter programming press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code98t display shows ALL NBR DELETED All numbers stored from all lists will be cleared Operating Modes You can switch between the operating modes using the SET CHG button and by entering one of the mode numbers The Call Blocker can toggle between the modes Standard Business or Standby using one of the settings Mode settings are displayed only when entering Programming Mode Standard default Mode Code 30 When calls come in all phone numbers that are Invited will ring phones throughout your home office like normal and to the TEL phone port on the back of the Call Bloc
3. from the phone in the TEL phone port This caller list should be used for your immediate family or associates who will need full access to you and your phone or for emergencies Blocked call 80 Sets of number or area code Callers on your blocked list cannot ring your phone in the TEL phone port and cannot leave a message Blocked numbers that you add and will be answered immediately followed by a hang up after 6 seconds When a callis being blocked and a busy signal will be heard in the handset of the phone in the TEL phone port Invited Callers Within a Blocked Area Codes 10 Sets of number Up to 10 separate numbers within an area code can be allowed to ring through when the entire area code is already blocked Example phone number 002 123 4567 is invited to ring through but the rest of the area code 002 is blocked OPX Type Calls Opx calls display as Anonymous Out of Area Private and Unknown or X calls that do not have a minimum 7 digit number displayed or have characters in the number like or or have been spoofed to look like a real number The factory setting is to hang up on these type of calls First Ring Suppression Code70 Not Suppression Code71 When a call comes in the phone company s Caller ID information will display on all phones connected to the telephone line but the Call Blocker will suppress the first ring to the TEL phone port to prevent it from ringing and receiving Caller ID If the caller is an in
4. ETE press the DIAL C button again to clear that displayed call or press and hold the DIAL C button 2 seconds to clear all call history Viewing Call History The UP BLO button displays the previous calls or Top of List The button displays the last call or End of List when call history stars to fill up with calls you can view faster to the X Top of List or the End of List by pressing and holding the UP BLO key 1 second to go to the Top of List or pressing and holding the key 1 second to go to the End of List Blocking Callers Can be enabled using the UP BLO or viewing buttons and pressing the SET CHG button once the Led brights constantly then press the button on the front panel NBR BLOCKED will display to show that call is now on the Blocked Call List When a blocked caller calls in the caller ID will display their number and BLOCKED which means the call is being answered and hang up on Inviting Callers Can be enabled using the UP BLO or viewing buttons then press the SET CHG button once the Led brights constantly then press the button one second and you see NBR INVITED will display to show that call is now on the Invited Call List When an invited caller calls in the caller ID will display their number and INVITED Inviting VIP Callers Can be enabled using the UP BLO or viewing buttons then press the SET CHG button once the Led brights constantly then press the two seconds and you see NBR VIP wi
5. ON To disable Monday thru Friday when the prompt for ENTER CODE displays enter Code 85 display shows SET MON FRI OFF Step 3 Saturday amp Sunday Enable 86 Disable 87 If you want the same interval to work during Saturday and Sunday when the prompt for ENTER CODE displays enter Code 86 display shows SET SAT SUN ON To disable this feature when the prompt for ENTER CODE displays enter Code 87 display shows SET SAT SUN OFF Step4 After Hours On or Off Off code80 On Code81 To enable After Hours Mode enter programming when the prompt for ENTER CODE displays enter Code 81 display shows AFTER HOUR ON To disable this feature off when the prompt for ENTER CODE displays enter Code 80 display shows AFTER HOUR OFF Note To enable AFTER HOURS MODE you must first enter Start and End Times above and enable day periods Monday Sunday Anonymous Out Of Area Private and Unknown Code72 Code73 IF you want to have an answer machine or your voice mail take these types of calls and not ring your phone connected to the Call Blocker you can program in Code 72 OPX override Note that Code 72 allows the OPX calls through to the line only not the TEL phone port To enable OPX override enter programming press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 72 display shows
6. OPX 5 RINGS If you want to restore blocking of opx calls later enter programming press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 73 display shows OPX HANG UP Private Call Pass Thru Enable Code74 Disable Code75 Using Code 74 can allow PRIVATE type calls with no number displayed to ring through to the TEL phone port while still blocking Out of Area and stored numbered calls To enable Private Call Pass Thru enter programming press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE then when the prompt for ENTER CODE displays enter Code 74 display shows ENABLE PRIVATE To turn this feature off when the prompt for ENTER CODE displays enter Code 75 display shows DISABLE PRIVATE OUT OF AREA Call Pass Thru Code76 Using Code 76 can allow OUT OF AREA type calls with no Number displayed to ring through to the TEL phone port while still blocking Private and stored number calls To enable Out of Area Call pass thru enter programming when ENTER CODE displays enter Code 76 display shows OUT OF AREA ON To turn this features off when the prompt for ENTER CODE displays enter Code 77 display shows OUT OF AREA OFF Inhibit the dialing of extentions Enable78 Disable Code 79 Using Code78 can inhibit someon
7. all end of the Power Supply into the port labeled 24VDC on the Call Blocker next plug in the Power Supply to a 120VAC wall receptacle Connect your combo Phone Answer Machine system to the TEL phone port of the Call Blocker and set to 3 5 rings Note if you are using Voice Mail services from your phone company then don t enable any answering devices there in your home or office Optional Connect an answer machine to any phone wall plate and set the answer delay to 4 6 rings or 1 2 rings greater than the answering device in the TEL phone port This separate answer machine will capture any uninvited calls not answered by the Combo Phone Answering device in the TEL phone port Telephone Call Blocker Back Panel Wall Plate gg ee ey SOOO DIALIC SETICHG INVIVIP BLOCK How D 820 Call Blocker Operates When Calls come in all calls displaying a phone numbers will ring through to the phones throughout your home office like normal and to the TEL phone port on the back of the Call Blocker Calls like Anonymous Out of Area Private and unknown displaying no phone number will be answered by the call blocker and hung up on unless program Code 72 is enabled to allow these call types to ring in If you are running a business and want to hear from Anonymous Out of Area Private and Unknown callers you can enable Business Mode Code 31 to allow all callers to ring through except those numbers you want to block Blocked callers will be imme
8. betel since1980 D 820CB D 820CB CALL BLOCKER DISPLAY VV V V V V WV TELEWELL ELECTRIC CO LTD LCD 3 LINE DISPLAY 62L x 21W mm 13 DIGITS TELEPHONE 15 DOT MATRIX CHARACTERS NAME DISPLAY TIME amp DATE EACH CALL INCOMING MEMORIES COUNTER NEW CALL INDICATOR DISPLAY NAME amp NUMBERS FEATURE amp SPECIFICATION y V V V V V V V v v Vv V FSKAND DTMF BOTH STANDARD STANDARD BUSINESS STANDBY MODE 64 CID LIST 80 BLOCKED LIST 8 10 B I LIST 30 INVITED LIST amp 30 VIP LIST AFTER HOURS MODE DIAL LIMIT 20 DIGIT NUMBERS FOR EVERY MEMORY 8 15 DIGIT NAMES FOR EVERY MEMORY CLOCK SETTING DESK OR WALL CONVERTIBLE MACHINE SIZE 93L x 80W x 37H mm POWER AC ADAPTER 5F NO 196 Sec 2 Chung Hsing RD Hsin Tien Taipei Hsien Taiwan TEL 886 2 29150386 FAX 886 2 29150385 Email telewell ms12 hinet net http www telewell com tw D 820CB PHONE BLOCKER USER MANUAL 2013 01 V1 1 No Battery Backup is Needed If there is a power outage all of the program settings remain intact 1 Connect the supplied line cord to your telephone wall jack and then to the Line Port on the Call Blocker You must connect the Line cord and your phone to the correct ports on order for the Call Blocker to operate properly Initially LINE IN WRONG PORT will show on the display until the Line cord is plugged into the LINE port CHECK CORDS will display if the Line cord is disconnected afterwards Plug the sm
9. d the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 50 to store an area code followed by the key So any phone number followed by the Invited area code can ring through example for Invited area codes enter Code 50 002 the n key is used as a wildcard replacement for any number display shows NBR INVITED Stored up to 30 sets of phone number including area code Inviting Callers within a Blocked Area Code Code52 You can program in specific invited callers within a blocked area code using the SET CHG button on the front panel To enable this feature press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 52 to store a number followed by the key Example for an invited callers in a blocked area code enter Code 52 002 123 4567 display shows B I BLOCKED Stored up to 10 sets of phone number Blocking Individual Callers Code40 To block specific individual callers press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 40 to store a number of your blocked caller followed by the 10 digit number then the key example for Blocked number enter Code 40 002 123 4567 display shows NBR BLOCKED Sto
10. diately answered and after one ring get hung up on The blocked caller can only hears one ring in there phone and then silence If you miss your invited caller your combo phone answer machine attached to the TEL phone port or phone company voice mail will take a message for you If your caller hang up during any part of the call so will Call Blocker to await another call VIP callers can ring through at any time regardless of After Hours Mode or Invited call settings Invited callers can only ring through normally when After Hours Mode is not enabled Type of Incoming Calls Default settings are All calls with numbers ring through All calls without numbers are answered and hungup on The Blocker caller hears only one ring and then silence The call Blocker will allow all phones connected to the line to ring Invited Callers 30 Sets of number or area code The factory setting is Global Invite of any call with a standard number displayed Invited caller cannot ring through during the After Hours Mode If you want specific callers to ring through at that time they must be added to the VIP list Invited caller List Limits include either unlimited numbers with Code 96 factory setting or added individually Vip callers 30 Sets of number These callers will be allowed to ring through at all times and are stored in a separated VIP list from the Invited callers VIP callers can ring through even when the After Hours Mode is used to route calls away
11. e use extention to dialout To enable this function enter programming when ENTER CODE displays enter Code 78 display shows LIMITED DIALING To turn this features off when the prompt for ENTER CODE displays enter Code 79 display shows UNLIMITED DIALING Dial Displayed Number Code 91 The DIAL button can be used to dial the number displayed of someone who has called in using the arrow UP and DOWN buttons to select a specific caller The default operation of the call blocker is to prompt you to either add or remove the n n is a wildcard replacement for any number maximum to 6 digit number before the call blocker dials the number The prompt will ask DIAL 1 USA Country Code and to answer that prompt use the down arrow key for Yes and the up arrow key for No To enable the dial n prompt enter programming press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 91 display shows DIAL n OFF To turn to default enter programming press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 91 display shows DIAL n ON Display All Installed Code Code 92 Press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt fo
12. for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 99 Adjust the Brightness of Led display Code 94 The Led display s brightness can be adjusted from 1 lighter to 9 darker To enable this function enter programming then enter Code 94 when ENTER CODE displays followed by the number 1 to 9 then the key Example for adjusted Lcd brightness enter Code94 9 the display shows BRIGHTNESS 9
13. ker except for Anonymous out of Area Private and Unknown callers showing no phone number These calls will be answered by the Call Blocker for processing and by default be hung up on unless Code72 is enabled to allow these call types to ring in Blocked callers will be immediately answered and after 6 seconds get hung up on To enable this default Mode press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 30 display shows STANDARD MODE You can use Code 76 to override the block function for Out of Area no number call types or Code 74 to override the block function for private no number call types These two codes will allow those callers you need to hear from Out of Area overseas or Private neighbors to ring through You can also use Code 52 to invite up to 10 callers within a blocked area code Business Mode Code 31 If you are running a business and want to hear from Anonymous Out of Area Private and Unknown callers as well as any other types of call you can enable Business Mode Code 31 to allow calls through to the TEL phone port except those you want to block This mode also works with your phone company s voice mail but also blocks those phone numbers you have entered into the Blocked Callers List Blocked callers will be immediately answered and after 6 seconds get hung up on To enable this mode press and hold the
14. ll display to show that call is now on the VIP Call List When a VIP caller calls in the caller ID will display their number and VIP Viewing Caller Lists You can review what numbers are stored in each caller list by entering programming press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter code Code 41 to view Blocked Caller list use arrow buttons to view up and down To remove an entry press the DIAL C button once when display shows DELETE press the DIAL C button again the number will then be removed from that list Code 51 to view Individually Invited Caller list use arrow button to view up and down To remove an entry press the DIAL C button once when display shows DELETE press the DIAL C button again the number will then be removed from that list Code 53 to view Invited Caller in a Blocked Area Code list use arrow buttons to view up or down To remove an entry press the DIAL C button once when display shows DELETE press the DIAL C button again the number will then be removed from that list Code 61 to view VIP Caller list use arrow button to view up and down To remove an entry press the DIAL C button once when display shows DELETE press the DIAL C button again the number will then be removed from that list Programming Numbers Invited VIP and Blocked Global Invited Factory Defau
15. lt Invites all callers who display a phone number You can invite all callers who display a phone number and yet block a single number or area code this one command will allow all invited callers who display a phone number to ring through to the TEL phone port and all other devices connected directly to the phone line To do this enter programming with the SET CHG button press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 96 display shows INVITE ALL NBR All callers in this list are considered Invited but not VIP callers who are in a separate list Invited Vip Callers I want to invite my family amp friends to ring through at any time You can program in specific VIP callers who can ring through at any time by using the SET CHG button on the front panel To enable this feature press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 60 to store a number of your VIP callers followed by the 10 digit number maximum to 20 digit number then the key Example for a vip number enter Code60 002 123 4567 display shows NBR VIP Store up to 30 sets of number Inviting Area codes Code50 You can program in specific Invited area codes using the SET CHG button on the front panel To enable this feature press and hol
16. n the Call Blocker display converts the telephone company s supply clock data into either AM or PM time If the morning hour are 1 00am 0100hours 2 00am 0200hours etc until noon 1200 hours and then the afternoon hours are 1 00pm 1300hours 2 00pm 1400hours etc until midnight 0000 hours So to set a time for a business after hours beginning in the early evening until the next morning or 5 00pm to 8 00am you would use the time of 1700 and 0800 as the two numbers for your after hours settings To set a time for dinner in the evening from 6 00pm to 8 00pm you would use the time of 1800 and 2000 To set a time for early morning until lunch time or 1 00am to 12 00pm you would use 0100 and 1200 After Hours Mode Settings Step 1 Start amp End Times Using the time as shown above set this feature on by enter programming press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then Pick Up Phone when the prompt for ENTER CODE displays enter Code 82 then START TIME displays enter the start time of day ex 1700 5 00pm from example above display shows CODE STORED Next when the prompt for ENTER CODE displays enter Code 83 then END TIME displays enter your end time of day ex 0800 8 00am display shows CODE STORED Step 2 Monday thru Friday Enable 84 Disable 85 To enable Monday thru Friday when the prompt for ENTER CODE displays enter Code 84 display shows SET MON FRI
17. r ENTER CODE displays enter Code 92 to see the current settings Dial nnnnnn Code 93 Before the Call Blocker dial the number reference above dial displayed number you can add up to 6 digit number To enable this function enter programming then enter Code 93 when ENTER CODE displays followed by the number maximun to six digit number you want to add then the key Example for a dial nnnnnn enter Code 93 002 display shows DIAL 002 Manually Set Clock and Date Code 95 The clock and date are determined by your local phone service and your phone company is responsible for keeping the clock and date accurate The Call Blocker only presents the clock and date that your phone company is delivering but you can manually set it Press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 95 followed by the year in two digits the month in two digits the day in two digits and the time in 4 digits Example 95 12 11 19 14 26 or 95 year 12 month 11 date 19 time 1426 2 26pm key to store Display will show the Time and Date changed immediately after you hang up Call your phone company and have them correct the clock and date settings Reset Call Blocker User Settings Code 99 To reset the call blocker s user settings to factory settings but not delete any call lists Press and hold the SET CHG button
18. re up to 80 sets of phone number Blocking Area Codes Code40 To block specific area codes press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 40 to store an area code followed by key So any phone number followed by the Blocking area codes will be blocked Example for Blocked area code enter Code 40 002 the n key is used as a wildcard replacement For any number display shows NBR BLOCKED Deleting Invited VIP B I or Blocked Numbers Code98 To delete a single number you have stored enter programming press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 98 enter the phone number you want to delete followed by the key Example for deleting a number enter Code 98 002 123 4567 display shows function Programming Numbers Invited VIP and Blocked con t Inviting Individual Callers and Code 97 I want to block all callers and just allow one or more numbers Note from the factory all callers with a number displayed are already invited and can ring through but you can create your own caller list by disabling the Global Invited list first You can then program in preferred Invited callers using the SET CHG button on the front panel To enable this feature press and hold the SET CHG button
19. vited caller then the caller ID information will display on the next ring to the phones connected to the TEL phone port thereafter This stops unwanted Caller ID information from being received by the phones connected to the Call Blocker s TEL phone port If you want to hear the first ring enter programming Press and hold the SET CHG button for 3 seconds until you see PROGRAM MODE then PICK UP PHONE when the prompt for ENTER CODE displays enter Code 71 display shows PASS 1ST RING This code will allow all rings and all Call ID information to be received by phones connected to the TEL phone port To return to the default first ring suppression mode enter programming when the prompt for Enter Code displays enter Code 70 display shows SKIP 1ST RING Automatic Caller ID Call Routing Caller ID service from your phone company is reguired for Your Call Blocker to work The first call to your Call Blocker unit will initialize the Clock and Date to the current date and time Automatic call routing will begin to work right after the first call when Call ID information 1s displayed Note that during Daylight Savings Time changes the phone company is responsible for updating their clock data when delivering the caller ID information Clearing Display To delete a single number from call history use the up and down arrow keys to select the number you want to remove press the DIAL C button once the display shows DEL
Download Pdf Manuals
Related Search