CP5-Series User Manual - American Weigh Scales
Contents
1. the DOWN position to enable the Auto Off feature VI Changing the Unit of Measure This scale can read in KG or LB G OZ for SR 1 To change the weighing mode follow these instructions 1 Press and hold until the scale displays the current weighing unit then release 2 Now tap the 0 key to toggle between the available weighing units 3 After a couple of seconds of no activity the scale will enter normal weighing mode with the selected unit SR 1KG Units g gram oz ounce SR 5 SR 20 Units Ib pound kg kilogram Vil Using the Tare Feature You can use this scale s tare feature to subtract the weight of an empty container or vessel for net weight determination NOTE The weight of the container will subtract from the available capacity 1 Turn on the scale as described in Section IV 2 Attach your tare item empty container using the hook and wait for it to stabilize HOLD will be displayed 3 Tap the button 0 0 will be displayed 4 You can now add items to the container to obtain just the weight of the contents 5 When the container is removed the weight will be held on the display Press 0 again to zero the scale Vill Calibration Calibration and adjustment are performed at the factory However the weighing range can shift slightly during shipping Also due to changes in local acceleration of gravity around the world adjustment is recommended when moving the scale from one lo2. American Weigh Scales SR Series User Manual SR 1KG 1kg x 0 0019 SR 5 5kg x 0 005g SR 20 20kg x 0 01kg Copyright 2010 American Weigh Scales Inc All rights reserved Rev 2 1 SR Series Manual Thank you for purchasing the American Weigh SR Series digital hanging scale Please read all operating instructions carefully before use Scales are precision measuring devices and should always be handled with proper care To ensure years of reliable service keep these simple tips in mind Do not exceed the scale s maximum capacity Overloading your scale can permanently damage it Avoid exposure to extreme heat or cold Scales perform best at normal room temperature If temperatures have changed dramatically calibration and adjustment may be necessary Allow your scale to warm up for 30 60 seconds before performing calibration and adjustment if available Store your scale in a clean dry location Dust dirt and moisture can accumulate on the weighing sensors and electronics causing inaccuracy or malfunction Avoid using your scale in close proximity to strong radio wave emitting devices such as computers cash registers and cordless phones Gently apply all items to be weighed Do not shock load items onto the weighing hook Avoid dropping your scale The warranty does not cover damage due to rough treatment or overload Check the batteries first if you are having any trouble with your scale This simple
3. cation to another To check calibration 1 Place the required calibration weight on the scale and note the displayed value 2 If the displayed value is not within acceptable tolerance see chart on next page adjustment is required SR Series Manual Model Acceptable Calibration Recommended Tolerance Weight Accuracy Class SR 1KG 2g 1kg OIML M1 SR 5 0 015kg 5kg OIML M1 SR 20 0 03kg 10kg OIML M1 IX Adjustment 1 Press the key to turn the scale on 2 Once the LCD shows 8888 tap tl times quickly until the inner code displays 3 Press again The display will flash CAL followed by the required calibration weight 4 Add the required weight The disp and return to normal weighing mode 5 Remove the weight and press and hold the 0 key to turn the scale off Calibration is complete X Troubleshooting Problem Scale will not turn on Solution Check the batteries he key several see chart ay will show pass Problem Display will not stabilize Solution Make sure the weight is stable on the hook and not shaking or swinging Problem Displayed weight is inaccurate Solution Perform a calibration adjustment XI Error Codes 1 OUTZ Zero setting has shifted Perform calibration adjustment If the problem persists the load cell may be permanently damaged due to overloading 2 EEEEE Maximum capacity exceeded Remove the extra weig
4. ht to avoid damaging the load cell 3 LLLLL Load cell has been overloaded 4 UNST The scale is unstable Use the scale in a more stable position XII Specifications Max Capacity Readability Min Capacity Dimensions Hook Dimensions Warranty Max Capacity Readability Min Capacity Dimensions Hook Dimensions Warranty 1000g 35 3002 1g 0 050z 3g 0 100z 2 x AAA Alkaline Batteries 4 0 x 2 3 x 0 7 Gap 0 5in Throat 0 5in 10 Year Limited Warranty 5kg 111b 20kg 441b 0 005kg 0 01Ib 0 01kg 0 02Ib 0 015kg 0 03Ib 0 03kg 0 06Ib 2 x AAA Alkaline Batteries 4 0 x 2 3 x 0 7 Gap 0 5in Throat 0 5in 10 Year Limited Warranty
5. step can remedy most scale issues Do not disassemble your scale This product contains no user serviceable parts I Part List 1 Scale 2 Weighing Tray 3 AAA Batteries x2 Il Key Description Auto Off Select ON OFF TARE Key Ill Battery Installation 1 Before using the scale for the first time check the battery compartment and remove any plastic insulation strips or packaging that may be in place to prevent battery drainage during shipping storage 2 If you are replacing the batteries make sure the positive and negative contacts are properly aligned SR Series Manual IV Operation 1 Press the key 2 Wait for the scale to stabilize will be displayed in the bottom left corner of the LCD Place the item to be weighed on the weighing hook 3 When the weight is stable the red light will turn on and HOLD will be displayed below the weight SR 5 and SR 20 only 4 Remove the object s from the hook and tap the 0 key to re zero the scale 5 To turn the scale off press and hold the 0 key V Auto Off Selection To conserve battery power this scale is set to turn off automatically after 60 seconds of inactivity 1 To disable the auto off feature open the battery compartment and locate the Auto Off Select switch see Section II 2 Move the switch to the UP position to disable the Auto Off feature 3 Move the switch to
Download Pdf Manuals
Related Search