Hobbico pdf
Contents
1. 5 Always use small movements until you learn how the model behaves DUAL RATES Control sensitivity can be changed by pushing down on the right stick on the controller The controller will make a short low pitched beep This mode should be used when flying indoors or when learning how to fly The controller will make a short high pitched beep when changing to high rates This mode should be used when flying outdoors or when more agility is desired The low rate sensitivity will always be 25 less than the high rate The overall controls can be adjusted by 1 Holding down the right stick until the controller starts beeping 2 Continue holding down the right stick and advance the throttle to the desired setting 3 Release the right stick and return the throttle to 0 The default setting is when the throttle stick is at 50 midstick FLIGHT MODE Sa Flight Mode Flight Mode Button Dual Rate FLIGHT MODES FLIGHTMODE To toggle between the normal and expert flight Easy OFF Low Push down on right top button and accelerometers off modes press the Flight Mode Button Normal OFF High release Audible low and high tone When the accelerometers are off the flight controller will Advanced ON Low make the Ominus more agile but also it is easier to crash Expert ON High Flight Mode LEDs steady on Easy and normal flight accelerometers on Flight Mode LEDs flashing Advanced and expert flight accelerometers off2. BEFORE FLYING PLEASE READ amp UNDERSTAND THESE INSTRUCTIONS and go to www knowbeforeyoufly org OMINUS epy tac Spare Blades 2 black 2 color Controller AA Batteries 4 Ominus Quadcopter En Battery as 2G Memory Card s Card Reader BB Phone Mount Light Shield CHARGING Plug the charger into a USB port or AC adapter not included as shown and connect the battery The charger LED is steady on when charging The LED flashes when charge is complete e NEVER leave the battery unattended while charging e DO NOT allow the USB port to power down while the charger is connected to the battery e ALWAYS unplug the charger from the USB port and the battery when charging is complete INSTALL BATTERIES INTO RADIO Slide the cover down and insert 4 AA batteries 2 Connect the battery to the Ominus and place it on a level surface The LED on the quad will flash rapidly when the 1 Turn on the radio with the throttle quad is linked to the radio and ready to fly at its lowest position ALWAYS unplug the battery after flying FLYING Rotate Right Rotate Left FLYING BASICS 1 Take off by slowly advancing the left stick until the quad takes off 2 Control altitude using the left stick Rotate Left 3 Use the right stick to move left right forward or backward 4 Use the left stick left right rotate or spin left or right
3. LOW BATTERY INDICATOR mma The LEDs on the Ominus will flash slowly when the battery voltage is low The Ominus FPV should be landed as soon as possible to avoid damaging the battery Always unplug the battery after flight The battery needs to be charged before the quadcopter is stored QUADCOPTER SENSOR CALIBRATION Es If the quadcopter is constantly drifting in the same direction or a new flight control board has been installed the sensors on the Ominus should be calibrated 1 Center all the trim adjustments To check the trim push the trim button once on one side and then once on the opposite side When the trim is centered the transmitter will emit a long low pitched beep The transmitter will emit a short beep of lower pitch as the adjustment gets closer to center and higher pitch as the adjustment moves away from center Continue pressing the trim button that has the lower pitch until the adjustment is centered 2 Push down on the right stick and hold it The radio will steadily beep while the stick is held down 3 Press down on the left stick 3 times within 2 seconds The radio will stop the steady beep and make a short beep when the stick is pressed the third time 4 Release both sticks and push up on the throttle trim button The red LED will flash slowly and become steady again when the calibration is complete 5 Press down on the left stick to save the settings FIRST PERSON VIEW FPV SETUP 1 Install the FPVCAM app from
4. Google Play Android or the App Store Apple aren F 009 pay a 4 Download on the AEN App Store mma 2 TE AM 7 5 E 1 Result amp 2 Remove the protective film from the camera lens 3 Insert the memory card into the camera on the quad NOTE ALWAYS have the power off to the camera when installing or removing the memory card HE bb 4 Install the phone mount onto the controller For optimal performance please keep the controller s antenna at least 7 18cm away from smartphones Failure to do so may result in ae unwanted interference which can cause pilots to lose control of Onhon tamara ieot be usen tor commen their model and or experience poor video reception Do not alter ventures Be sure to fly in a safe environment and the smartphone holder in any way respect the privacy of others Apple and the Apple logo are trademarks of Apple Inc registered in the U S and other countries App Store is a service 5 Install the Light shield if desired mark of Apple Inc Android and Google Play are trademarks of Google Inc 00 8 18 AM T ma a B 17 AM 7 38H08 DEDO z 8 15 AM lt Settings Wi Fi Enter the password for FPV_Ominus Camera List Cancel Enter Password Wi Fi RE Password 1234567890 CHOOSE A NETWORK Please add a camera OIWJEIRITIYIULITOIP Ask to Join Networks AS DFGHIKL non networks will Be joined automatically e ave o manualy oast aneno Mi
5. T RETURN YOUR PRODUCT TO THE STORE Dromida will repair or replace factory defects for 90 days from the date of purchase This warranty specifically does not cover crash damage misuse or abuse To make a warranty claim please contact our product support team at 1 217 398 8970 option 6 or e mail us at helihotline greatplanes com If requested by Product Support please send defective product to Hobby Services 3002 N Apollo Dr Suite 1 Champaign IL 61822 Please include a note about the problem your contact information and a copy of the receipt This warranty applies only if the product is operated in compliance with the instructions and warnings provided with each model Dromida assumes no liability except for the exclusive remedy or repair of parts as specified above Dromida shall not be liable for consequential or incidental damages Some states do not allow the exclusion of consequential or incidental damages so the above exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state FCC REQUIREMENT This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAU
6. THORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT CE COMPLIANCE INFORMATION FOR THE EUROPEAN UNION INSTRUCTIONS FOR DISPOSAL OF WASTE EQUIPMENT BY PRIVATE USERS IN THE EUROPEAN UNION Dl This symbol on the product or its packaging indicates this product must not be disposed of with other household waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to a conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or location where you purchased the product DECLARATION OF CONFORMITY Product Dromida 2 4GHz 4 Channel Tx Rx FCC ID U45 NEOTO15 Item number DIDJ1101 0200 Dromida Wi Fi Camera Equipment class 1 0200 transmitter The objects of the declaration described here are in conformity with the requirements of the specifications listed below following the provisions of the European 2006 95 EC Low Voltage Directive EN 60950 1 2006 Safety The objects of the declaration described here are in conformity with
7. d 140 F 60 C e Do not attempt to charge a battery if it is swollen or hot e Do not place the charger or any battery on a flammable surface or near combustible materials while in use e Never disassemble or modify pack wiring in any way or puncture cells e Never charge inside a vehicle e Always disconnect the battery and remove the charger from the USB port when not in use e Land your model immediately when the LEDs flash to indicate that the battery power is low Recharge the battery before attempting another flight A dangerous situation can occur when attempting to recharge an over discharged battery e ALWAYS keep a supply of sand accessible when charging Dumping sand on the battery will extinguish a LiPo chemical fire ALWAYS KEEP OUT OF REACH OF CHILDREN SAFETY PRECAUTIONS EEE Follow these safety precautions when operating this or any model quadcopter e Adult supervision required e Before flying go to www knowbeforeyoufly org e Your Ominus FPV quadcopter should not be considered a toy but rather a small working model If not operated correctly the model could possibly cause injury to you or spectators and damage to property e Do not touch the spinning blades or fly over another person s head e Keep your face and body as well as all spectators away from the e You must check the operation of the model before every flight to insure that the model has remained structurally sound rotors whenever the bat
8. drop the files onto your computer 6 Once videos pictures are downloaded they can be viewed in the picture folder and be shared through social media NOTE f your computer doesn t recognize flv video formats download VLC Media Player from http www videolan org in for this to work This will download the video to your phone DELETING FILES Se 1 Files can be deleted from the memory card while the USB adapter is still installed into your computer by selecting the desired file s and deleting them 2 If the memory card is installed in the camera you can delete the videos or photos by simply pushing and holding the desired video or photo for one second A box will appear with a trash can Simply push the trash can icon and the video or photo will be deleted You can select more than one file at a time to be deleted This can be done before or after they have been downloaded to your phone TROUBLESHOOTING PROBLEM The quadcopter will not respond to the radio SOLUTION 1 Charge or change the battery on the quadcopter 2 Turn off the radio and disconnect the battery for the Ominus Re link the Alagoa er and ragio PROBLEM Will not take off PROBLEM Red radio LED light flashing after linking SOLUTION Rotor blades incorrectly installed See Rotor Blade Replacement SOLUTION Replace with new AA batteries section PROBLEM Unable to flip PROBLEM Quadcopter is shaking SOLUTION Battery voltage too low SOLUTION Chec
9. k the canopy chassis motors and rotor blades for damage BLADE REPLACEMENT 1 Remove screw that secures the rotor blade to the gear shaft 2 Pull prop off the gear shaft PROBLEM Gyro not working properly SOLUTION 1 Battery voltage low 2 Re link 3 Land onto the ground for 3 seconds and take off again 3 Install new rotor blade and secure with screw FRONT Note The rotor blades have arrows that indicate which direction they rotate Please id a refer to this diagram to verify that the correct replacement rotor blade is installed REAR Black Blades White LEDs GEAR SHAFT REPLACEMENT EEE 1 Remove the rotor blade from the gear shaft 2 Push the shaft down to remove it from the gear 3 Install the new gear shaft and rotor blade if it is not damaged Note While the gear is out check it carefully for any cracks or damage to the teeth MOTOR REPLACEMENT mma 1 Remove the screw securing the motor cover to the arm and pull the cover off the motor 2 Use a small flat blade screwdriver to separate the motor plug from the socket DO NOT pull the wires 3 Remove the motor from the frame and insert the replacement Make sure that the wire colors on the replacement motor are the same as the original The motors for the clockwise props have black and white wires The counter clockwise props use motors with blue and red wires FLIGHT CONTROL BOARD REPLACEMENT aaeaaeeeee board inside of the arm
10. me Z XCV BN MIR 23 space Join 6 Turn on the controller and plug in the battery for the Ominus FPV 8 Open the FPVCAM app on your phone and push the in the upper 7 Go to the Wi Fi setting on your phone and check that the FPVCAM is NUNE ANE COMME le WI ocat Mo gamera on The password for the FPV Cam is 1234567890 9 Once the device finds the camera push the button The FPV Wi Fi is a registered trademark of the Wi Fi Alliance camera should be displaying at this point FPV VIDEO RECORDING PICTURES ug STOPS RECORD RECORD 1 To activate the record function simply push and release the Video On Picture Button on the back right hand side of the controller 2 While recording you can take a still photo Push and hold the Video On Picture Button for 2 seconds 3 To stop recording video push the Video Off Button on the back left hand side of the controller NOTE You can also take pictures and stop start videos directly from the app Access the controls by tapping on the screen 4 Once you are done recording video or photos click the download button from the main screen NOTE The quad must still be plugged e Q B42 AM Camera List FPV_Ominus FPV vy 5 To download the videos or photos to your computer remove the memory card from the camera install it into the USB card reader Then insert the card reader into a USB port on your computer Open the removable disk folder and drag and
11. s 5 Remove the control board Transfer the O rings to the LEDs on the new 6 Install the new control board and route the wires for motors To prevent damage to the wires route them between the guides on the 8 Replace the motor covers 1 Remove all 4 motor covers 2 Disconnect the camera wires from the quad 3 Remove the 4 screws that secure the battery frame to the main frame 4 Remove the LED covers on each arm 7 Install the LED covers There are openings on the cover for the wires Before tightening the screws make sure the wires are positioned correctly 9 Calibrate the quadcopter sensors BATTERY Se The Ominus FPV uses a lithium polymer LiPo battery Follow these precautions to insure safe and trouble free operation e ALWAYS disconnect the battery from the quadcopter when not in use e Only use the included charger with the flight battery e Do not attempt to use this charger with NiCd or NiMH battery packs e Do not attempt to use a damaged battery e This product contains a LiPo battery Must be recycled or disposed of properly e Do not leave the charger unattended while charging Disconnect the battery and unplug the charger immediately if either becomes hot However it is normal for the charger to get warm e Disconnect the battery from the charger and carefully move the battery to a fireproof location if the battery begins to swell or smoke e Never allow the battery temperature to excee
12. tery is connected Stay clear of buildings trees and power lines AVOID flying in or near e Do not alter or modify the model as doing so may result in an unsafe or unflyable model crowded areas DO NOT fly close to people children or pets e Maintain a safe pilot to quadcopter distance while flying REPLACEMENT PARTS 1 DIDE1150 1 DIDE1151 1 DIDE1152 1 DIDE1153 2 DIDE1154 2 DIDE1155 2 DIDE1156 2 DIDE1157 3 DIDE1141 4 DIDE1158 5 DIDE1114 6 DIDE1159 6 DIDE1160 6 DIDE1161 6 DIDE1162 7 DIDE1163 8 DIDE1131 9 DIDE1130 10 DIDE1164 11 DIDE1135 11 DIDE1136 11 DIDE1137 11 DIDE1138 12 DIDE1140 13 DIDM1105 13 DIDM1106 13 DIDM1107 13 DIDM1108 14 DIDE1165 15 DIDP1101 16 DIDE1166 17 DIDZ1502 DIDE1167 DIDJ1101 DIDP1120 DIDZ1501 HMXZ0002 Micro Card Reader Canopy GREEN Canopy RED Canopy BLUE Canopy YELLOW Prop Set GREEN Prop Set RED Prop Set BLUE Prop Set YELLOW Screw Set Gear Set Bearing Set Main Frame GREEN Main Frame RED Main Frame BLUE Main Frame YELLOW Main Gear Shaft Main Motor CCW R F Main Motor CW L F R Motor Covers o LED Covers GREEN LED Covers RED LED Covers BLUE LED Covers YELLOW LED O Rings E Board GREEN E Board RED E Board BLUE E Board YELLOW Battery Frame LiPo 1S 700mAh 35C Camera Foam Tape WIFI HD Camera Q200 Phone Holder Q200 Transmitter USB 1S LiPo Charger Micro Card Reader per Comil SF ii Am 90 DAY LIMITED WARRANTY mma PLEASE DO NO
13. the requirements of the specifications listed below following the provisions of the European R amp TTE directive 1995 5 EC EN300 328 V1 8 1 Technical requirements for radio equipment ETSI EN 301 489 1 V1 8 1 301 489 17 V1 3 2 General EMC requirements for radio equipment Hobbico Inc 2904 Research Road X Champaign IL USA 61826 Distributed in Europe by Revell GmbH D 32257 B nde Germany The associated regulatory agencies of the following countries recognize the noted certifications to this product as authorized for sale and use DIDEO2xx Mnl v1 1 2015 DROMIDA A HOBBICO COMPANY Hossico dromida com
Download Pdf Manuals
Related Search