NOVA- 600 EBX Pentium® Embedded Board
Contents
1. 31 4 5 Peripheral Setup iterare dese eve dal 32 4 6 Power Management 33 2 E Key FUNC ON nee 34 Appendix Watch Dog Timer 36 Appendix B FP24 01 Module 37 Introduction Welcome to the NOVA 600 EBX Pentium Embedded Board The NOVA 600 board is an EBX form factor board which comes equipped with high performance Pentium CPU and advanced high performance LCD CRT interface 10 100Mbps Ethernet etc excellent features designed for the system manufacturers integrators or VARs that want to provide all the performance reliability and quality at a reasonable price This board built in DiskOnChip DOC Flash Disk for embedded application The DOC Flash Disk is 100 compatible to hard disk User can use any DOS command without any extra software utility The DOC currently is available from 2MB to 72MB An isolated digital I O function is designed on the board The function provides 4 bit digital inputs and 4 bit digital outputs It is very useful in embedded application In addition the NOVA 600 built in C amp T 65555 HiQPro LCD CRT Chipset and 2MB EDO RAM The LCD interface can drive up to 1280x1024 with 256 colors The support flat panel will cover Color STN TFT EL etc and also 3 3V or 5V version 1 1 Specifications The NOVA 600 Pentium withHiQPro _CD CRT Single Board Computer2. 3A max Windows 95 NT Driver for DIO application The WDT 01 Windows 95 NT software utility are included in the CD ROM From the WDT 01 utility you may use the DIO H DIO LIB and DIO DLL for the digital I O application The software user manual are also in the CD ROM You may print it out for better reference 26 27 AMI BIOS Setup The NOVA 600 uses the AMI BIOS for system configuration The AMI BIOS setup program is designed to provide maximum flexibility in configuring the system by offering various options which may be selected for end user requirements This chapter is written to assist you in the proper usage of these features 4 1 Getting Start When power on the system the BIOS will enter the Power On Self Test routines These routines will be executed for system test and initialization and system configuration verification After the POST routines are completed the following message appears Hit DEL if you want to run SETUP To access AMI BIOS Setup program press Del key then you could see the screen to make some options as follows When choose Load BIOS Defaults will load the minimized settings for Troubleshooting The performance should be very poor when use this setting When choose Load Setup Defaults will load optimized defaults for regular use Choosing this setting will modify all applicable settings 28 4 2 Standard CMOS Setup The Standard CMOS Setup is used for basic hardware
3. OPEN OPEN 66MHz OPEN e CPU to Bus Multiple we err qun 3 4 5 6 7 8 OPEN OPEN CLOSE OPEN CLOSE CLOSE CPU Frequency CPU Clock x Multiplier for example Pentium 200MHz 66MHz CPU Clock x 3 CPU Core Voltage Selection Please check the CPU Core Voltage before you install the CPU Right now new Intel MMX CPU is dual voltages for core and l O the I O is 3 3V but the core is 2 8V This kind of CPU design will enhance the low power consumption capability As for the general Pentium CPU is one voltage for and Core 3 3V 3 4V or 3 5V e JP1 CPU Core Voltage Setting JP1 is in the DC Power Module CPU Core JP1 JP1 JP1 JP1 Voltage 1 2 3 4 5 6 7 8 3 5V P54C CS CLOSE CLOSE CLOSE CLOSE VRE 3 4V P54C CS OPEN CLOSE CLOSE CLOSE STD 3 3V CLOSE OPEN CLOSE CLOSE 3 2V OPEN OPEN CLOSE CLOSE 3 1V CLOSE CLOSE OPEN CLOSE 3 0V OPEN CLOSE OPEN CLOSE 2 9V CLOSE OPEN OPEN CLOSE 2 8V OPEN OPEN OPEN CLOSE 2 7V CLOSE CLOSE CLOSE OPEN 2 6V OPEN CLOSE CLOSE OPEN 2 5V CLOSE OPEN CLOSE OPEN 2 4V OPEN OPEN CLOSE OPEN 2 3V CLOSE CLOSE OPEN OPEN 2 2V OPEN CLOSE OPEN OPEN 2 1V CLOSE OPEN OPEN OPEN 2 0V OPEN OPEN OPEN OPEN Dual Single CPU Voltage setting Vcore amp VIO JP13 JP13 JP14 JP14 1 2 3 4 1 2 3 4 Pentium CLOSE CLOSE OPEN OPEN P54C IDT C6 Pentium OPEN
4. and Pin10 to active the circuit You may refer the following block diagram to know the details The external power supply s DC output should be not connected with the NOVA 600 s power supply at either 5V 12V or ground to isolate the NOVA 600 main system and the external I O device In case you could not find an external power supply to active the Digital l O you may use the 5V or 12V from the system s power supply Under the situation the digital I O function will be not isolated e CN14 DIO Connector Pin Signal Name Function 1 INOO Data IN 2 INO1 Data IN 3 INO2 Data IN 4 INO3 Data IN 5 OUTOO Data OUT 6 OUT01 Data OUT 7 OUTO2 Data OUT 8 OUTOS Data OUT 9 COM External Power Ground 10 COM External Power 5 30V The digital I O are addressed at 220H 240H 260H or Disable through CMOS peripheral setup selection You may refer the following table for the address and matching I O port Bit O Bit 1 Bit2 Bit3 Bit4 Bit5 Bit6 Bit7 INOO INO1 INO2 INO3 OUTOO OUTOI OUTO2 OUTO3 The Digital Input specifications are Isolated channel with common power 25 Digital input level Logic level 0 1V max Logic level 1 3 5V to 30V Input impedance 3K ohm 0 5W The Digital Output specifications are Isolated channel with common power Open collector to 30V Output current 600mA per channel total
5. cancel this command Because some OS under certain situations have problem for this feature it is normally disable 4 5 Peripheral Setup 31 This setup is almost working for Multi I O Chip W83877F and ALI Alladin 4 chipset These options are used to change the ChipSet s registers Please carefully change any default setting to meet your application need perfectly The only special concern is Onboard Serial PortD If you are using the IrDA port you have to set this port accordingly Customer also can set the Isolated Digital I O function I O addressing here by 220h 240h 260h or disable The most important setting in this setup is LCD Type setting In the most right bottom item Panel Type selection customer can choose 15 different panel type The 15 panel types are 1024x768 Dual Scan STN Color 1280x1024 TFT 640x480 STN 800x600 STN 640x480 TFT 640x480 18bit 1024x768 TFT 800x600 TFT 800x600 TFT 10 800x600 TFT 11 800x600 STN 12 800x600 STN 13 1024x768 TFT 14 1280x1024 STN 15 1024x600 STN 4 6 Power Management Setup 32 Power Management Setup help user handles the NOVA 600 board s green function The features could shut down the video display and hard disk to save energy for example The power management setup screen is as following Power Management APM Disable Max Saving Min Saving or User Defined Note Advanced Power Management APM have to be installed to
6. keep the system time updated when the computer enters suspend mode activated by the Power Management Under DOS environment you need to add DEVICE C DOS POWER EXE in your CONFIG SYS Under Windows 3 x and Windows 95 you have to install Windows with APM feature A battery and power cord icon labeled Power Will appear in the Control Panel 33 Key Function The NOVA 600 provides an outstanding E KEY Munction for system integrator Based on the E KEYTWou could free to store the ID Code Pass Word or Critical Data in the 1Kbit EEPROM Because the EEPROM is nonvolatile memory you don t have to worry the losing of the very important data Basically the E KEY Ms based on a 1Kbit EEPROM which is configured to 64 words from 0 to 63 You could access read or write each word at any time When you start to use the E KEYTWou should have the utility in the package The software utility will include four files as follows README DOC E2KEY OBJ EKEYDEMO C EKEYDEMO EXE The E2KEY OBJ provides two library function for user to integrate their application with E KEY Munction These library read e2key and write e2key are written and compiled in C format Please check the following statement then you will know how to implement it easily 34 unsigned int read_e2key unsigned int address This function will return the E KEY s data at address The address range is from 0 to 63 Return data is one word 16 bits vo
7. provides the following specification CPU Pentium MMX up to 233Mhz AMD processor up to 300MHz Cyrix 6x86MX and IDT C6 processor e Bus ISA bus and PCI 32 bit local bus PCI 2 1 standard e Chipset ALI Alladin 4 e LCD CRT Interface C amp T 655555 Chipset with 2MB EDO RAM CRT Resolution 1280x1024 256 colors 1024x768 64K colors 800x600 16M colors 36 bit LCD Interface Resolution 1280x1024 256 colors 1024x768 64K colors 800x600 16M colors Please contact www chips com to get more information e Ethernet Built in the RTL8139 Chipset IEEE 802 3u 100BASE TX standard Auto sensing interface to 10MBps 100MBps networks Full duplex capability More information WWW realtek com tw e Real time clock calendar in Alladin 4 chipset backup by industrial Li battery 3V 850mAH e RAM memory up to 128MB SDRAM supported e Second Cache memory 512KB Pipelined Burst SRAM on board e Ultra DMA 33 IDE Interface up to four PCI Enhance IDE hard drives The Ultra DMA 33 IDE can handle data transfer up to 33MB s The best of all is that is new technology is compatible with existing ATA 2 IDE specifications So there is no need to do any change for customer s current accessory e Floppy disk drive interface two 2 88 MB 1 44MB 1 2 720KB or 360KB floppy disk drives e Four high speed Series ports NS16C550 compatible UARTs 1 2 Bi directional Parallel Port IrDA port Support Serial Infrared SIR and Amplit
8. 6 2 2 Setting the CPU of NOVA 600 9 2 3 Wafch Dog TiIMer natirara nem 11 2 4 DiskOnChip Mlash Disk 12 2 5 LCD Voltage Setting 13 2 6 Clear CMOS Setup 13 2 7 Battery Backup for CMOS Setup 13 2 8 BIOS Flash Chip Write Voltage Setting 14 2 9 PortB RS 232 RS 422 or RS 485 Setting 14 2 10 PortC PortD RI Pin Setting 15 3 CONNECH ON 16 3 1 Floppy Disk Drive 16 3 2 Disk Drive 17 3 3 Paralel PO ite a ttr tete a e 19 34 Serial Porte a Hi d de N ib 19 3 5 Keyboard Connector 20 3 6 External Switches and Indicators 21 3 7 USB Port Connector 21 3 8 IrDA Infrared Interface Port 22 3 9 LED CRT Connector ped 22 3 10 Fan Gonriector oi ERI ease uH 23 3 11 Lan RJ45 Connector 24 3 12 Power Connector tepidis ideni 24 3 13 Isolated Digital Connector 25 4 AMI BIOS 5 28 41 Getting Start nennt 28 4 2 Standard CMOS Setup 29 4 3 Advanced CMOS 30 4 4 Advanced Chipset
9. NOVA 600 EBX Pentium Embedded Board Copyright 1998 All Rights Reserved Manual first edition Aug 01 1998 The information in this document is subject to change without prior notice in order to improve reliability design and function and does not represent a commitment on the part of the manufacturer In no event will the manufacturer be liable for direct indirect special incidental or consequential damages arising out of the use or inability to use the product or documentation even if advised of the possibility of such damages This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer Trademarks NOVA 600 is registered trademarks of Acquire Inc IBM PC is a registered trademark of International Business Machines Corporation Intel is a registered trademark of Intel Corporation AMI is registered trademarks of American Megatrends Inc Other product names mentioned herein are used for identification purposes only and may be trademarks and or registered trademarks of their respective companies Contents 1 Introduction ata renne 3 1 1 Specifications ats nee ie 4 1 24 What YOU eite a Ee oc Demetr eee beet 5 GU S UU UU DOCEMUR 6 2 1 NOVA 600 s Layout and Dimensions
10. OPEN CLOSE CLOSE MMX AMD K6 Cyrix 6x86MX Dual Voltage e Cyrix 6x86MX PR Rating Table Vcore 2 9V dual voltage PR Rating Bus MHz CPU Core Clock 10 MHz Multiplier 6x86MX PR133 100 2 6x86MX PR133 110 2 6x86MX PR150 120 2 6x86MX PR150 125 2 5x 6x86MX PR166 133 2x 6x86MX PR166 138 2 5x 6x86MX PR166 150 6x86MX PR166 150 2 5x 6x86MX PR200 165 6 86 200 166 2 5x 6x86MX PR200 180 3x 6x86MX PR233 200 3x 6x86MX PR266 233 3 5x AMD MMX Rating Table dual voltage Product Name Core Vcore Bus MHz Multiplier K6 233 model 6 233MHz 3 2V 66 3 5x K6 200 model 6 200MHz 2 9V 66 3x K6 166 model 6 166MHz 2 9V 66 2 5x K6 300 model 7 300MHz 2 2V 66 4 5x K6 266 model 7 266MHz 2 2V 66 4x K6 233 model 7 233MHz 2 2V 66 3 5x 2 3 Watch Dog Timer The Watch Dog Timer is enabled by reading port 443H It should be triggered before the time out period ends otherwise it will assume the program operation is abnormal and will issue a reset signal to start again or activate NMI to CPU The Watch Dog Timer is disable by reading port 043H e JP18 Watch Dog Active Type Setting JP18 DESCRIPTION 2 3 RESET WHEN WDT TIME OUT 11 ACTIVATE NMI TO CPU WHEN WDT TIME OUT DISABLE WDT JP11 Time Out Period OPEN 220 sec 2 4 DiskO
11. Ultra DMA 33 interface CN13 IDE 1 Primary IDE Connector 2 54mm pitch CN10 IDE 2 Secondary IDE Connector 2 0mm pitch for 2 5 IDE HDD e CN13 Primary IDE Interface Connector 6 8 DATA10 9 DATA4 25 17 CN10 Secondary IDE Interface Connector 6 9 8 DATAt0 9 DATA4 18 3 3 Parallel Port This port is usually connected to a printer The NOVA 600 includes an on board parallel port accessed through a 26 pin flat cable connector e 8 Parallel Port Connector 6 DATA4 8 DATA6 9 DATA p 3 4 Serial Ports The NOVA 600 offers four high speed NS16C550 compatible UARTs with Read Receive 16 byte FIFO serial ports CN6 PorB PortD 20 pin Header Pin Description Pin Description 1 DCD2 TX2 11 DSR2 RX2 2 RXD2 TX2 12 RTS2 RX2 3 TXD2 13 CTS2 4 DTR2 14 RI2 5 GND 15 NC 6 DCD4 16 DSR4 7 RXD4 17 RTS4 8 TXD4 18 CTS4 9 DTR4 19 RI 5V or 12V 10 GND 20 NC CN7 PortA PortC 20 pin Header 19 Pin Description Pin Description 1 DCD1 11 DSR1 2 RXD1 12 RTS1 3 TXD1 13 CTS1 4 DTR1 14 5 GND 15 NC 6 DCD3 16 DSR3 7 RXD3 17 RTS3 8 TXD3 18 CTS3 9 DTR3 19 RI 5V or 12V 10 GND 20 NC 3 5 Keyboard and Mouse Conn
12. ector The NOVA 600 provides 5 pin keyboard and mouse connectors The connector is 2 5mm pitch model Say Yea 2570 05P or equivalent one e CN20 5 pin Header Keyboard Connector KEYBOARD CLOCK KEYBOARD DATA GROUND CN21 5 Mouse Connector 2 MOUSEDATA N C 3 6 External Switches and Indicators 20 There are many external switches and indicators for monitoring and controlling your CPU board e CN15 Reset Connector PIN NO DESCRIPTION 1 RESET SIGNAL 2 GROUND CN2 Speaker Connector PIN NO DESCRIPTION 1 5V 2 SPEAKER e CN25 IDE LED Connector PIN DESCRIPTION 1 5V 2 HDD ACTIVE CN22 KeyLock amp Power PIN NO DESCRIPTION 5V N C GROUND KEYLOCK GROUND 3 7 USB Port Connector The NOVA 600 built in two USB ports for the future new I O bus expansion CN18 USB 0 1 1 5V 2 GND 3 DO 4 Di 5 DO 6 Dt 7 GND 8 5V 3 8 IrDA Infrared Interface Port 21 The NOVA 600 built in a IrDA port which support Serial Infrared SIR or Amplitude Shift Keyed IR ASKIR interface When use the IrDA port have to set SIR or ASKIR model in the BIOS s Peripheral Setup s PortD Then the normal RS 232 PortD will be disabled e CN23 IrDA connector PIN NO DESCRIPTION 3 9 LCD CRT Connector The NOVA 600 built in 10
13. id write_e2key unsigned int address unsigned data This function will write the given data to address The address range is from 0 to 63 The data value is from 0 to Oxffff To easy start to use the function please refer the include EKEYDEMO C code at first Please note the E7KEY unction is based on the working of parallel port So you should enable the NOVA 600 s parallel port otherwise will be not working Appendix A Watch Dog Timer 35 The Watch Dog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that caused the CPU to crash This condition may have occurred by external EMI or a software bug When the CPU stops working correctly hardware on the board will either perform a hardware reset cold boot or a non maskable interrupt NMI to bring the system back to a known state The Watch Dog Timer is controlled by two I O ports 443 Read Enable the refresh the Watch Dog hex Timer Disable the Watch Dog Timer hex To enable the Watch Dog Timer a read from I O port 443H must be performed This will enable and activate the countdown timer which will eventually time out and either reset the CPU or cause an NMI depending on the setting of JP18 To ensure that this reset condition does not occur the Watch Dog Timer must be periodically refreshed by reading the same I O port 433H This must be done within the time out period that is selected by jum
14. nChip Flash Disk The DiskOnChip Flash Disk Chip DOC is produced by M Systems Because the DOC is 100 compatible to hard disk and DOS Customer don t need any extra software utility It is just plug and play easy and reliable e JP16 DiskOnChip Memory Address Setting CE000 06000 DE000 2 5 LCD Voltage Setting The NOVA 600 supports 3 3V or 5V LCD panel by jumper setting 12 The setting will control the CN5 s Pin 29 amp 30 as 3 3V or 5V output e JP10 LCD Voltage Setting 2 6 Clear CMOS Setup If want to clear the CMOS Setup for example forgot the password you should clear the setup and then set the password again you should close the CN26 pin 3 4 about 3 seconds then open again Set back to normal operation mode close pin 2 3 CN26 Clear CMOS Setup Reserve Function DESCRIPTION Normal Operation Clear CMOS Setup 2 7 Battery Backup for CMOS Setup There have one 4 pin header CN26 using for battery backup function When close the pin 2 3 will use the on board battery When use external battery you should take off the jumper and use the connector as external battery connector e CN26 Battery Backup Function DESCRIPTION 2 3 CLOSE Using Internal Battery 1 Vbat Use as External Battery 4 Ground Connector 13 2 8 BIOS Flash Chip Write Voltage Setting The BIOS Flash Chip could be two types one is 12V write voltage and other one is 5V e JP17 5V 12V Flash Chip Wri
15. per group JP11 A tolerance of at least 30 must be maintained to avoid unknown routines within the operating system DOS such as disk I O that can be very time consuming Therefore if the time out period has been set to 10 seconds the I O port 443H must be read within 7 seconds Note when exiting a program it is necessary to disable the Watch Dog Timer otherwise the system will reset Appendix B FP24 01 Flat Panel Connection Module 36 The FP24 01 connection module is installed on the NOVA 600 as a standard product The FP24 01 converts NOVA 600 s on board 50pin LCD interface signal to the 44 pin 2x20 pin header and 41pin Hirose DF9 41P 1V LCD connectors The 44 pin or 41 pin connector will only support 24 bit flat pane e J3 44 pin LCD Interface Connector Jax 40 ENABKL FPVDD 44 5V or 3 3V e J1 41 pin LCD Interface Connector 1 2 GND 37 12V 41 NC e J2 LCD Backlight Power Connector PIN NO DESCRIPTION 12V 0 9A max 5 FPVEE Inverter Enable 38
16. pin VGA connector directly to your CRT monitor And the built in 50 pin connector for LCD interface e 9 10 pin VGA Header Connector 6 NC 8 GROUND 9 GROUND CN5 50 pin LCD Interface Connector P34 22 Ei a ae P8 O 3 10 Fan Connector The NOVA 600 provides CPU cooling fan connector chassis fan connector These connectors can supply 12V 500mA max to the cooling fan The 12V on the fan connector is converted from 5 50 it is limited in fan using Don t use it for other purpose e CN27 CPU Fan Connector 3 11 Lan RJ45 Connector The NOVA 600 built in RJ45 Lan connector for 10 100Mbps Ethernet communication 23 e CN1 Lan RJ45 Connector 6 e CN24 Lan Active LED Connector Pin Description 1 5V 2 RX TX LED1 YELLOW RX TX Active LED2 GREEN 100Mbps Active LED3 GREEN 10Mbps Active 3 12 Power Connector The NOVA 600 provides a 8 pin power connector The connector type is Molex 26 60 4080 or equivalent one The power connector s each pin max rating is 7A It will accept max 14A by the 2pin 5V input e CNA Power Connector PIN NO DESCRIPTION 3 13 Isolated Digital I O Connector The NOVA 600 built in 4 bit IN and 4 bit OUT digital I O connector The connector type is DINKLE ED350V 10P 24 Because this is isolated Digital I O design it will need an external power supply to the connector s Pin 9
17. system configuration The main function is for Date Time setting and Floppy Hard Disk Drive setting Please refer the following screen for this setup For IDE hard disk drive setup please check the following possible setup procedure 1 Use the Auto setting for detection during bootup 2 Use the IDE HDD AUTO DETECTION in the main menu to automatically enter the drive specifications 3 Manually enter the specifications by yourself from the User option 29 4 3 Advanced CMOS Setup This Advanced CMOS Setup is designed for customer 5 tuning best performance of the NOVA 600 board As for normal operation customers don t have to change any default setting The default setting is pre set for most reliable operation You also can option the system keyboard primary display PS 2 mouse to enable or disable The system boot sequence is also set here by first second third and fourth boot device setting 4 4 Advanced Chipset Setup 30 This setup functions are almost working for ChipSet ALI 4 These options are used to change the ChipSet s registers Please carefully change any default setting otherwise the system could be running un stable Auto Configuration Enable or Disable When use the 60nS general type DRAM please enable the setting to get the optimal timings SDRAM Speculative Read Enable or Disable When enable this option the PCU will send predict commands to the SDRAM if a miss happens the CPU will
18. te Voltage Setting This jumper is factory setting customer may not change it 12V 1Mbit Flash Write Voltage 12V 1Mbit 2Mbit Flash Write Voltage Write Voltage 2 9 PortB RS 232 RS 422 or RS 485 setting The PortB on can be set as RS 232 RS 422 0r RS 485 mode by the JP4 JP6 or JP12 PortB Mode JP4 JP6 JP12 RS 232 Don tcare 2 3 1 9 3 10 5 11 7 12 RS 422 2 3 1 2 1 2 3 4 5 6 7 8 RS 485 1 2 1 2 1 2 3 4 5 6 7 8 14 2 10 PortC PortD RI pin setting The PortC s RI pin pin 19 on CN7 and the PortD s RI pin pin 19 on CN6 can be set as RI 5V or 12V mode PortC JP1 JP3 CN7 Pin 19 2 3 Don t Care 5V 1 2 1 2 12V 1 2 2 3 PortD JP2 JP21 CN6 Pin 19 2 3 Don t Care 45V 1 2 1 2 12V 1 2 2 3 Please note when set the 12V ouput the board should have 12V input from power supply by the CN4 power connector 15 Connection This chapter describes how to connect peripherals switches and indicators to the NOVA 600 board 3 1 Floppy Disk Drive Connector NOVA 600 board equipped with a 34 pin daisy chain driver connector cable CN11 FDC CONNECTOR PIN DESCRIPTION PINNO DESCRIPTION NIC 26 NOS INDEX 9 GROUND 16 3 2 PCI E IDE Disk Drive Connector You can attach four IDE Integrated Device Electronics hard disk drives to the NOVA 600 IDE controller The IDE support
19. ude Shift Keyed IR ASKIR interface USB port Support two USB ports for future expansion Watch dog timer can be set by 1 2 10 20 110 or 220 seconds period Reset or NMI was generated when CPU did not periodically trigger the timer Your program use hex 043 and 443 to control the watch dog and generate a system reset Flash Disk DiskOnChip The Flash Disk provide 100 compatible with hard disk The built in TrueFFS Transparent Flash Block Management and Space Reclamation will let customer to use the Flash Disk with DOS command no need any extra software utility Keyboard connector Mouse PS 2 Mouse Port on board Power Consumption 5V 51 Pentium MMX 200 32MB SDRAM Operating Temperature 0 55 C CPU needs Cooler What You Have In addition to this User s Manual the NOVA 600 package includes the following items NOVA 600 Pentium withHiQPro _CD CRT Single Board Computer Installation This chapter describes how to install the NOVA 600 At first the layout of NOVA 600 is shown and the unpacking information that you should be careful is described The jumpers and switches setting for the NOVA 600 s configuration such as CPU type selection system clock setting and watch dog timer are also included 2 1 NOVA 600 s Layout and Dimensions lt reference next page gt 2 2 Setting the CPU of NOVA 600 e CPU Clock Setting CPU Speed Clock JP15 JP15 JP15 1 2 9 10 11 12 60MHz CLOSE
Download Pdf Manuals
Related Search