Home

GSM06 User Manual - PiSector Home Security Alarm Systems

1. Fig 4 this example Before setting the panel makes alarm and the siren rings immediately when zone After setting alarm will be after the preset time set the delay time under system setting I is triggered 3 11 Adding Phone Number This system can store up to 6 phone numbers When triggered the system will call out these numbers in order until someone answers the call The system will redial three times at most Without the approval and consent of relevant authorities do not set any of the dial out numbers to 911 112 or 999 or any other emergency service provider Method enter phone number setting menu press 4 or 6 to choose Phone1 or Phone2 Phone3 Phone6 and then press ENTER Input the number you want to set then press ENTER to save Operation figures Fig 1 enter phone number setting Fig 2 choose serial NO Fig 3 input phone number 123456789 Input phone number No number 123456789 26 3 12 Deleting Phone Number Method enter phone number setting press 4 or 6 to choose serial number then press 8 to choose Delete and then press ENTER to confirm Operation figures 123456789 Fig 4 the 1st number is deleted Delete 27 3 13 Adding SMS Cell Phone Number This system can store 3 SMS receiving cell phone numbers When alarming it will send SMS to all these numbers
2. Main unit panel operation press ARM The system will enter arm status after the delay time default 60 seconds 56 4 2 Home Arm Home arm means part of the defense zones are in arm status When there is someone at home it is recommended for safety purpose to enable some of the detectors such as sensors for door window balcony etc and disable the others such as sensors for the hall or some places easy to be triggered by person at home Remote controller press home arm button r on the remote controller Main unit panel press STAY 4 3 Disarm The purpose of disarming the system is to disable all sensors except those set to 24 hour Arm Delay Mode It can be used while the system is armed or while the system is in alarm state Use the main unit panel keypad to input user password The screen will display System disarmed Remote controller press disarm button CR on the remote controller Main unit panel password ENTER 4 4 Answer Alarm Call When the main unit panel sounds an alarm it will dial the preset numbers If no one answers the call the system will call the next number automatically If someone answers the call they will hear your 10 sceond pre recorded voice message Then can then interact with system via their telephone keypad If they hang up immediately without answering the call the system will continue cycling through the preset numbers for three times at most Pre
3. Method enter SMS number setting press 4 or 6 to choose SMS 1 or SMS 2 or SMS 3 and then press ENTER Input the number you want to set then press ENTER to save Operation figures Fig 2 choose serial number and press ENTER No number 13812345678 Input phone number 28 3 14 Deleting SMS Cell Phone Number Method enter SMS number setting press 4 or 6 to choose serial number then press 8 to choose Delete and then press ENTER to confirm Operation figures Fig 2 choose the number you want to delete d 138123456784 29 3 15 Set Net Work Center Function The network function of community shall be supported by the monitor center the protocol of monitor center shall be compatible with the system s protocol otherwise the networking may not work This system supports phone center and SMS network center If you need to use the network function please contact us The setting of network function includes center phone numbers user IDs and other parameters Set center phone number enter the Network Centers menu and the Phone Center menu and then press ENTER key to enter setting status Input the phone center number and save it The detailed operation diagram is as follows Diagram1 Enter Network Centers Diagram2 Choose Phone center menu menu and then confirm No number 075512345678 075512345678 Input phone n
4. NEVER insert SIM card during power on Connect the power adapter The main unit panel will start self inspection and the POWER indicator LED will flash once per second If this LED does not light on you need to restart the main unit panel Please do it at least 10 seconds later as repeated power on and off in short times will shorten the service life of the system The POWER indicator will flash once every 3 seconds after finding GSM network successfully This is the normal system state Turn on the internal backup battery switch on the back of the main unit panel Check the GSM signal icon on the LCD screen Signal less than 3 bars will affect normal performance Please place the main unit panel at a place with good GSM signal reception 3 System Setting Instructions 3 1 Entering Setting Mode All settings have to be done in the setting mode Use keys 2 8 4 6 as direction keys up down left right At the disarm state input your 6 digit password default 888888 then press ENTER The main unit panel will sound a beep and the SET indicator lights on The screen will display Remote Control menu Fig 2 please enter password Fig 3 press ENTER to set 10 3 2 Adding Remote Controller This system supports maximum 8 remote controllers 2 free remote controllers come with PISECTOR Alarm System package have been coded All extra remote controllers have to be coded with the main unit panel in order to p
5. mode the power supply adapter for the main unit panel shall be connected to a safe and reliable mains outlet Do not place the system near your bedroom or office desk because the siren will make very high pitch sound in case of alarm which may adversely affect your rest work health or your unborn baby If the alarm system will not be used for a long time disconnect it from the power supply Do not disassemble repair or alter the product without permission or it may cause accidents or fire PiSector Inc is NOT responsible for any consequences whatsoever rising from such unauthorized actions 64 lt gt Do not drop the product on the ground or on hard surfaces as it may lead to intermittent malfunctions and or system damage or total failure lt Without the approval and consent of relevant authorities do not set any of the dial out numbers to 911 112 or 999 or any other emergency service provider Read the suggestions above carefully as they are required to maintain your obligations under the warranty terms and for prolonging the service life of the system and follow the instructions therein If any equipment does not work as specified contact PiSector Inc support pisector com or your local authorized sales agent TAMPERING WITH THE EQUIPMENT IN ANY WAY WILL AUTOMATICALLY VOID YOUR WARRANTY 65 The following sensors are optional and packed separately q E Wireless Outdoor
6. siren and press the code button on the wireless siren until you see all 4 lights are on This means the siren is in setting status waiting for the console to send a signal Then go back to the console Then select Wireless Control menu on the main unit panel and press Enter to Enable Press 6 to select Transmission press Enter The main unit panel will send a wireless signal to the siren You will hear a beep from siren mean add successful Operation figures 38 Enable Fig3 Press 6 to choose Wireless siren Transmission 3 23 Wireless Siren Code Encryption The alarm signal code used with the wireless siren is sent from the internal transmitter of the main unit panel The code of this signal is the same for all wireless alarm systems produced by PiSector Inc If you and your neighbor are using the same model the alarm signal from your neighbor may cause your siren to sound off too It is therefore recommended that you encrypt the wireless siren to avoid interference or use external transmitter Method enter Wireless Control menu and then Control menu Press 39 to choose Wireless siren then press 8 to choose Encryption Input 4 numbers randomly and then save it BE AWARE any time you change this Encryption code you need re program your siren again 40 Operation figures Enable Fig 3 press 6 to choose wireless siren 8907 Encryption Please input
7. system can store 30 alarm records The last alarm is ranked as the first record And when the record number exceeds 30 the oldest record will be overwritten automatically Method In disarmed state input 00 ENTER the main unit panel enters the state of Alarm record Press 4 or 6 to upturn or downturn and press Exit to exit checking Fig 1 press 00 in disarm status Fig 2 press 4 or 6 to check 01 Zone SOS E EN T2 Fig 3 press 4 or 6 to check 08 Zone GAS 11 12 12 2313 6l 5 Technical Specifications Input Voltage DC12V 1A Standby Current 35mA Alarming Current 450mA Wireless Frequency 433MHz PT2262 EV 1527 4 7MQ GSM Frequency 900 1800 850 1900 MHz Backup Battery NI HIAAA 6 DC 7 2V Siren Volume lt 110dB Alarm Defense Zone Information effective invalid EE oe it e fe me mmm m re premio te om on fr Eee m Jem qu 62 6 Care and Maintenance This wireless alarm system has an excellent design and uses advanced sensitive electronics that require care and dust free environment The following suggestions are required to maintain your obligations under the warranty terms and for prolonging the service life of the system lt gt lt gt Place the main unit panel and all accessories out of children reach Keep the alarm system dry rain humidity and various fluids or mois
8. to the main unit panel you do not need code identify them again if you want to add extra sensor late by yourself you need code it to the main panel in order to perform correctly The sensor cannot be the same as any of the saved sensors in the main unit panel has a unique address Method press key 888888 default password then press enter then press 6 to choose zone menu press enter you will see zone as Fig 2 if you press 6 will get zone2 zone3 you choice which zone you want to code the sensor then press 8 to find Coding then press ENTER to confirm you will see 000000000 as Fig 3 then trigger the sensor you will see the sensor s address number as Fig 4A then press ENTER to save it as Fig 5 If the sensor has been saved before after triggering it the main unit panel LCD screen will display Error Repeated code as Fig 4B 14 Operation figures Fig 2 choose zone number and press ENTER 241015162 01010101010101010 Normal code Trigger sensor Fig 4B the main unit has the same code with sensor code Error Repeated code 15 3 5 Installation of Door Sensors All door sensors which come from PISECTOR Alarm System standard box have coded to main panel you do not need code them again Door sensor used for detecting the status of open and close of windows and doors It will detect it and send the signal to control panel NOTE Please test each sensor before you mount the sensor to the appropriat
9. 0290099571360225909013509124 9 T2 Tee 834791315155748572424541506959508295331168 6172785588907509838175463746493 Sector com 67
10. 41 3 24 Change Operation Password The operation password is used for daily use of the system disarm or remote control The default operation password is 1234 Method Enter Settings menu and then Operate password Input the 4 digit password you want to set and save it Operation figures Fig 4 save it Please input 42 3 25 Change Program Password The program password is used for system setup default is 888888 Method Enter Settings menu and then Operate password press 6 to choose Program password Input the 6 digit password you want to set and save it Operation figures Fig 3 press 6 to choose program a Fig 4 input password and save it passwor 888888 43 3 26 Setting Arm Delay Time After setting the system will enter OUT ARM status after the preset delay time Delay time ranges from 01 99 seconds The system default time is 60 seconds Method Enter Settings menu then you will see Operate password Press 6 to choose Delay arm Input the time you want to set and save it Operation figures Fig 2 you l see Operate password menu Fig 4 input time and save it 08 Please input 44 3 27 Setting Alarm Call Out Delay Time After setting when there is an alarm the system will call out after the preset delay time Delay time ranges from 01 99 seconds The system default time is 60 se
11. CTION iii 30 Delito VOICE ee 32 3 18 VOICE RECORDING TE 33 9419 SETTING SYSTEM DATE su 34 3 20 SETTING SYSTEM TIME eee cneee nee nana asa seres see Dn ya a Rx a OUR 35 3 21 SCHEDULING TIMELY ARM tede dessins o uuu os Peu ois eara 36 3 22 SCHEDULING TIMELY DISARM eceeeee cereo cinerea inne dan 37 9 29 WIRELESS SIREN LODING Im memet rere 38 3 24 WIRELESS SIREN CODE ENCRYPTION eene 39 3 25 CHANGE OPERATION PASSWORD cessere 42 3 26 CHANGE PROGRAM DAGSwWORD eene nnns 43 3 21 SETTING ARM DELAY TIME ee 44 3 28 SETTING ALARM CALL OUT DELAY TIME eene 45 29 20 VOICE PROMPT EE 46 3 30 SIREN PROMPT SETTING FOR REMOTE CONTROLLER 47 3 31 BACKLIGHT SETNING so 48 3 32 SIREN SETTING IN EMERGENCY MODE eee 49 3 33 ARM DISARM SMS NOTIFICATION eese 50 3 34 LANGUAGE SETTING rrnnunnnnnnnnennnnnnnnennannrnnennnennnnennsrnnnsennssnnnn 51 3 35 SET MAX RING TIMES BEFORE ANSWERING eee 02 3 36 CHOICE MODE OF ALARM NETWORK ne o3 Su FACTORY RESET aean o4 dido PASSWORD RESET ide a Ea da 99 4 SYSTEM USAGE INSTRUCTIONS censere nn 56 4 1 SD iiie o6 4 2 HOME ARM eege Eeer of 4 3 DISARM D QT of 4 4 AER EE 58 4 5 REMOTE CONTROL datet 59 4 6 EMERGENCY ALARM GAL Luise 60 4 1 WSEAS TELEPHONE Lassen 60 4 8 ALARM HISTORY REVIEW
12. IDiskcron PiSector All in ONE Wireless GSM Alarm System B5 EE 4H M00 ET ER S egegeep w 2 l oio F RTE LE EE ETTE QZ Q 0 ll EE T Cica a e E E E i amp 3 KE B AER5AE ARRA 5 0 S ll EEE t stes ET vad EEE User Manual GSM 06 Read manual fully before use PiSector Inc USA www pisector com 1 gt INTRODUCTION ems 5 2 SYSTEM INITIALIZATION tee p rr eceaka or aa RR Mrd oa a es 9 3 SYSTEM SETTING INSTRUCTIONS eee 10 3 1 ENTERING SETTING MODE 0ccceeceeeeeeseeeeeeeeaeeeseeeneeeseeeees 10 3 2 ADDING REMOTE CONTROLLER eeeeeee seen ee nana anna caus 11 3 3 DELETING REMOTE CONTROLLER eec eee rennen nnne 13 3 4 ADD SENSORS TO MAIN PANEL NENNEN nnn 14 3 5 INSTALLATION OF DOOR SENSORS nennen 16 3 6 INSTALLATION OF WIRELESS PIR MOTION SENSORS 18 3 7 DELETING DEFENSE ZONE and assa efa 21 3 8 SETTING DEFENSE ZONE PLACES eese nee 22 3 9 SETTING DEFENSE ZONE MODES eese 23 3 10 SETTING DEFENSE ZONE SIREN 2 000 000c00cec0eeeeseeeceerceeesees 24 9s ALARM DELAY SETTING desc oni joes soa See 25 3 12 ADDING PHONE NUMBER 25329 adii dena ee 26 3 13 DELETING PHONE NOUMER 2f 3 14 ADDING SMS CELL PHONE NUMBER een 28 3 15 DELETING SMS CELL PHONE NUMBER eee 29 3 16 SET NETWORK CENTER EUNG
13. Signal Repeater Wireless Keypad Siren with flash e Se ei Glass Sensor Panic Button Remote Controller I IS Ne d P u Wireless Smoke Gas Detector Wireless Pet Detector Immune PIR Detector Choose according to your specific needs Typical house configuration External Sirens Garage I N j o e Ce f E Smoke S amp v PIR Movement Detector Detectors 66 JL E RE ER 09399257510992U97494159230 791604062562009980 280348253421170679821480865132823066470938 446095505822317253594081284811174502841027 019385211055596446229489549303819644288109 756659334461284756482337867831652712019091 456485669234603486104543266482133936072602 491412737245870066063155881748815209209628 292540917153643678925903600113305305488204 005212941409519415116094153505727036027595919 osUS2TIOGLITSOl93260LIlYTEBSl0Sl1824950 40101623799 oZ214956755L985752124091227192581920119491299 336733624406566430860213949463952247371907 0217986094570277053921T7T1707295117675259467438 184676694051320005681271452635608277857713 427577896091736371787214684409012249534301 65499093 IM S0T OZ 7 T9606 02 6025 ZU LOIS H 290219608640344181598136297747713099605187 Ot WAI Wis yao ac E 529160969 185950244594553469083026425223082533446850 so25I9SSILtoolTIUIU0DOSISTOoSOJOzo0060070235920903 814206171776691473035982534904287554687311 Hon E Polos IOUS NT HOGG LUISE GLT NT NNN OTZUIUDS4OD00DOZIO000095015529192790529305019 D20599010
14. able Operation figures Fig 1 enter settings menu Fig 3 press 6 to choose disarm SMS Enable Disable 50 3 33 Language Setting This alarm system supports English and Chinese languages Please enter the Settings menu and you will see Operate password Press 6 to choose Language Press ENTER to switch between languages Operation figures Fig 4 choose the version you need 51 3 34 Set Max Ring Times Before Answering Call the main panel after the ringing circle the main panel will active automatically then you can remote control the alarm system follow prompt Operate enter settings menu press ENTER enter operate password then you will see Line Rings enter a number which you want to system active after how many rings Diagram3 Press Key 6 to enter line Diagram3 Press Key 6 to enter line rings menu rings menu 52 3 35 Choice Mode of Alarm Network Sets the system alarm network the system can select phone line alarm Or GSM line alarm or telephone line GSM line alarm Method entre into setup mode press ENTER enter operator password 1234 then press 6 to choose the alarm mode menu to decide the choice alarm network Diagram3 Press Key 6 to enter alarm mode menu Diagram2 Enter Operate Diagram1 Enter Settings menu password menu 1234 53 3 36 Factory Reset If the system ever becomes unstab
15. conds Method Enter Settings menu then you will see Operate password Press 6 to choose Delay alarm Input the time you want to set and save it Operation figures pee e mmm mmm mmm mmm mmm mmm mmm mmm mmm Fig 1 enter settings menu Fig 3 press 6 to choose delay alarm Fig 4 input time and save it 15 Please input 45 3 28 Voice Prompt Setting The main unit panel has voice prompt feature For example when user press arm or disarm on the remote controller it will give voice prompt The system default for the voice prompt is on Users can disable or enable it according to actual need Method Enter Settings menu then you will see Operate password Press 6 to choose Voice prompt and choose Enable or Disable Operation figures Enable DIREI 46 3 29 Siren Prompt Setting for Remote Controller If enabled the siren will sound a short beep each time you press the remote controller System default is disabled Method Enter Settings menu and then you will see Operate password Press 6 to choose Siren prompt and choose Enable or Disable Operation figures Fig 1 enter settings menu Fig 2 you ll see operate password menu BRIEFE Enable 47 3 30 Backlight Setting The backlight of the LCD screen and keypad will be off automatically after a certain period of time when there is no o
16. ctivates all other sensors CALL For making phone calls Enter the number you want to call and then press this CALL button Press again to end call hang up SOS press to raise an emergency alarm ESC clears the input content or back to last operation ENTER confirms current command or operation q WBS AAS SANS AR I E Lf P ZS d 3 DO ss S i gt m Ka CS 2 HE i ES i SS e o A m gt G I l Fons quo NS lr d i o ES ES FAT o St 90 000 000 00 00 0 0 6 GND 4 Wired Port Function interface of the main unit T VCC External keyboard power supply 12V Connecting external keyboard A 4 B Connecting external keyboardB gt 5 6 Zone1 Wired sensor 1 support both NO and NC 8 Zone2 Wired sensor 2 support both NO and NC Internal Backup Battery Switch Power port for 12V 1 2AM adapter plug in SP Siren in for plug a external siren or wireless siren transmitter Tel Your exist telephone device connector port LINE Main telephone line connector jack SIM Card Slot Please pay attention to the direction arrow marked on the slot LOCK OPEN Do not insert or take out the SIM card when the main unit panel is powered on 2 System Initialization Correct initialization of the main unit panel is important to its normal working and lifespan 1 2 Connect the wired accessories that you need Insert the SIM card
17. e location Place each sensor in the appropriate location Note If possible place the bracket on the stationary frame of door or window and place the magnet on the door or window itself Various orientations between the Bracket and Magnet may be used as long as 3 4 p Window Mounting distance is not exceeded See Example in Figures 1 4 Figure I Figure 2 Figure 3 Figure 4 Level Orientation Angled Orientation Perpendicular Orientation Perpendicular Orientation 16 NOTE SPACERS IN BOTTOM TRAY MAY BE USED ON THE BRACKET OR MAGNET TO ADJUST ALIGNMENT Once you have determined the appropriate location and orientation for the Bracket and Magnet attach them with double sided tape the Magnet Space and Bracket Space are optional only apply when your door window gap is big or very low R Magnet 7 Jo Am Y Y A Be pf Ch Cree WS ee A A gt j i ad e LA L Be 4 Ga Bond Space Bracket Space Sensor racxe oS Tape Pica Tape Optional use optional use 17 3 6 Installation of Wireless PIR Motion Sensors Mount Motion Sensors Prepare Motion Sensor Separate the front and back covers of the Motion Sensor by pressing the tab with your finger or the top of a pen Figure A B Remove insulating paper from batteryand close the cover The sensor needs 2 3 minutes to initialize itself so it should be left in the room being mindful that no one t
18. e Front Cover as shown in Figure 1 and then re attach the Front Cover Mount Motion Sensor Place the motion sensor following the location recommendations check marked locations shown in Figure C Avoid the et Be example location marked with the X which are household areas that typically cause false alarms such as heat air conditioning fans or direct sunlight The recommended mounting height is 6 5 7 0 feet for both coverage and pet immunity purposes Apply the 3M adhesive tape in the locations shown in Figure D for corner mounting or wall mounting mer 19 If you prefer to use screws to mount the motion sensor follow the screw position shown in Figure E optional PIT FF px pr3 COD 7 OD AR U Ind fm j E LU A ad A ars r at 1 mm pm I q N VE J 3 We fy d b d Zu i Remove PCB board SS Wall Fix SER Detection Patterns Motion sensor Specifications Replacement Battery CR123A The best Mounting Height 6 30 Feet Work temperature less than 34 degree Range Approximately 40 feet with 90 degree field of view 45 degrees to each side 20 Deleting Defense Zone The wireless detector cannot trigger the main unit panel after it is deleted Method enter zone setting menu press Enter then press 4 or 6 to choose the zone number which you want to delete then Press 8 to find Delete and then press ENTER Operation figures Fig 2 c
19. e you want to set DIKY loiro 36 3 21 Scheduling Timely Disarm This feature is also called Timely Disarm After setting the required disarm start time the alarm system will disarm itself at the pre set time Note disable the timely disarm just set time over 24hours e g 24 03 this function will disable Method enter Time menu you will see Date menu then press 6 to choose Timely arm Input the exact time you want to start the disarming period and press ENTER to confirm Operation figures pe e mmm mmm mmm mmm mmm mmm mmm mmm mmm Fig 1 enter time setting menu Fig 2 you ll see date setting menu 117 12 12 Fig 3 press 6 to choose timely disarm Disable 37 3 22 Wireless Siren Coding If you want to add a extra wireless siren to the main unit panel you need code identify the siren to main panel in order to work correctly Main panel have build in a Code Button transmitter for wireless siren the wireless siren which come from PISECTOR ALARM SYSTEM BOX has coded with Main panel customer just place the siren to where you like inside house or outside house and connect the 12V 0 5A power adapter to a wall out plug if you armed the main panel and trigger a sensor siren will goes off Method Go to the wireless
20. erform correctly Their code cannot be empty or the same as those already saved in the main unit panel Method enter remote controller setting menu press 4 or 6 to choose remote controller serial number press 8 to find Coding and then press ENTER to confirm Trigger the remote controller you want to add the main unit panel will make two beeps after receiving it And then press ENTER to confirm If the remote controller has been saved before after triggering it the main unit panel will make four beeps and LCD screen display Error Repeated code 11 Operation figures Fig 2 choose remote control serial number and coding menu 077015192 070101010 0 101070 Normal code Trigger remote Fig 4B the main unit has the same code with remote controller code Error Repeated code 12 3 3 Deleting Remote Controller If the remote controller is lost or damaged it must be deleted immediately so no other person can control the main unit panel Method enter remote controller setting menu press 4 or 6 to choose the remote controller you want to delete Press 8 to find Delete and then press ENTER Operation figures Fig 2 choose the controller you want to delete Delete 13 3 4 Add Sensors to main panel This alarm system supports 10 wireless defense zones each of zone supports up to 10 wireless sensors All sensors and sirens in the standard package have been coded
21. hoose zone number Delete Fig 3 choose Delete and press ENTER 21 3 7 Setting Defense Zone Places The location of defense zone can be set in the main unit panel so that the main unit panel can send detailed alarm messages There are 8 locations for alarm SOS fire gas door hall window balcony and boundary Please refer to Chapter 6 Technical Parameters for default settings Method enter defense zone setting menu press 4 or 6 to choose the zone number and then press 2 or 8 to enter zone place menu Press ENTER will shift the places Operation figures Place Fire Place GAS 27 Fig 4 this example Before setting the alarm SMS for zone 1 is 01 zone fire alarm After setting it 1s 01 zone gas alarm The format of alarm SMS 01 10 zone place alarm For example you set the place of zone 4 as Window The alarm SMS you receive is 04 zone B01 sensor number window alarm 3 8 Setting Defense Zone Modes There are different defense zone modes out arm home arm arm and disarm mode For example if you need gas detectors working all the time then please set ARM HOME and DISARM all enabled Note Such as CO detector smoke detector needs a independent zone do not set those detector with window door sensor or motion sensor in one zone we advice user set motion sensors in one zone window door sensors in other zone separate Method enter defense zone
22. le or if you need to change cellular network it is recommended to make a full factory reset of the system Enter Settings menu and then you will see Operate password Press 6 to choose Factory setting After this operation all the settings will be restored to factory defaults and all sensors and sirens have to be re coded too Operation figures Fig 2 you ll see operate password menu Restore 54 3 37 Password Reset If users forget the password they can input 95175308246 in disarm status to retrieve it The main unit panel will display Please wait Back to default password After this operation the operate password will be reset back to factory setting 1234 and program password to 888888 Operation figures o oo mn pn mn pn zm mn Fig 1 under disarm status Fig 3 confirm the operation 55 4 System Usage Instructions 4 1 OutArm Out arm means all the defense zones are in arm status When there is nobody at home it is recommended to arm the system with all detectors enabled If any detector is triggered by intruder fire gas leakage water leak etc the system will make alarm calls and SMS notification Use the main unit panel keypad to press ARM You will hear 60 beeps one per second and then the screen will display System armed Remote controller operation press arm button 15 on the remote controller
23. peration on the keys Users can set it keep on if required System default is disabled Method Enter Settings menu and then you will see Operate password Press 6 to choose Backlight on and choose Enable or Disable Operation figures ii Pn O pn mn zm rn mn zm rn mn zm Fig 2 you ll see operate password menu Fig 4 choose enable disable SIE T Enable 48 3 31 Siren Setting in Emergency Mode When you press the emergency button of the remote controller the siren does not normally sound as this feature is disabled by default Users can enable disable according to the actual need Method Enter Settings menu and then you will see Operate password Press 6 to choose Remote siren and choose Enable or Disable Operation figures Fig 1 enter settings menu Fig 2 you ll see operate password menu Fig 4 choose enable disable Disable 49 3 32 Arm Disarm SMS Notification When a user arms or disarms the system other users can be notified automatically via SMS notifications to all SMS numbers The SMS message content will be one of the following arm modes Out arm System armed Out disarm System disarmed Method Enter Settings menu and then you will see Operate password Press 6 to choose Arm disarm SMS and choose Enable or Dis
24. riggers it while it is setting S1 switch for LED signal light The default is set to on but if you do not want a flashing light when the sensor detects an intruder you can turn it off When the battery is low the LED light becomes yellow Make sure S2 at the DF position for system GSMO6 S1 S2 Switch Note Please test each sensor before you mount the sensor in the appropriate location Test the Motion Sensor The Motion Sensor is in Walk Test mode during the first 3 minutes after the front cover is re attached During walk test mode the LED blinks when motion is detected and then waits 60 seconds before resuming motion detection During normal operation the LED will remain on for 3 seconds when motion is detected until the Motion Sensor blinks once 18 again before resuming motion detection for next detector Move away from the area that is in direct line of sight of the Motion oensor move to an adjacent room Wait 60 seconds until the LED stops blinking Move back into the line of sight of the Motion Sensor walk around 3 5 steps this will trigger the main console If the Motion Sensor test is successful the LCD screen will display xxx Sensor Alarm If these words do not appear either A the 20 second waiting period since the last trigger has not expired or B the Motion sensor is not in communication with the PISECTOR system main console If you want to re start the Walk Test mode again open th
25. setting menu press 2 or 8 to choose HOME arm status enable or disable press ENTER to confirm Setting methods for OUT arm and DISARM are the same Operation figures Fig 1 enter defense zone setting Fig 2 choose mode WR HOME Disable HOME Enable Fig 3 press ENTER to confirm Fig 4 this example Before setting zone 1 does not alarm in home arm status After setting it will alarm when triggered in home arm status 3 9 Setting Defense Zone Siren The siren can be set on or off when there is an alarm for each defense zone independently Method enter defense zone setting press 2 or 8 to choose siren enable or disable and then press ENTER to confirm Operation figures Fig 2 choose siren status Fig 3 press ENTER to confirm Siren Enable Siren Disable Fig 4 this example Before setting the siren is on when zone alarms After setting siren will not sound when zone 1 alarms 24 3 10 Alarm Delay Setting Alarm delay the main unit panel will make alarm call and the siren will go off if enabled for this zone after a preset delay time Method enter defense zone setting press 2 or 8 to choose delay enable or disable and then press ENTER to confirm Operation figures Delay Disable Fig 3 press ENTER to confirm Delay Enable
26. shed successfully you will hear a voice prompt System armed Press 2 disarm if finished successfully you will hear a voice prompt System disarmed Press 3 monitoring for 30 seconds to continue monitoring press 3 again for another 30 seconds You can cancel monitoring at anytime by pressing 1 to arm and 2 to disarm Press 4 two way intercom for 30 seconds You cannot operate the main unit panel during this time You can cancel intercom at anytime by pressing 1 to arm and 2 to disarm 59 4 6 Emergency Alarm Call Sometimes there may be some accidents happening such as sudden illness of old people or children fire accident burglar intrusion Press SOS button on keypad or EM button on remote controller or wireless panic button the main unit panel will alarm and make call to the preset user numbers Remote controller operation press ay button on the remote controller Main unit panel operation press SOS The SMS content for emergency help is 00 zone SOS alarm 4 7 Use as Telephone In disarmed state you can use the main unit panel to make any call just like a normal telephone Dial telephone number on keypad press CALL button and the main unit panel will make a beep and the LCD screen will display the number you are calling After the call press CALL button again to hang up and the main unit panel will go back to disarmed state 60 4 8 Alarm History Review This alarm
27. ss Listen to the alarm information Press 1 Main unit panel stops alarming and still keep Arm status it will stop calling users Press 2 Main unit panel stops alarming and change Disarm status it stops calling users Press 3 Siren off and monitors the scene for 30 seconds for continued monitoring press 3 again to monitor for another 30 seconds Press 4 Main unit panel starts a 30 second two way intercom It cannot be controlled by the mobile during the time of intercom Note if you use landline only then you need press at end otherwise the landline will block 3mints multi phone numbers e g if you saved 5 numbers to the system the landline will block 3x5 15minits E g press 1 instead only if you use landline only you need press 1 58 4 5 Remote Control Dial the number of the main unit panel by phone and after 1 ring you will hear a voice prompt Please enter password If the password is correct you will then hear a voice prompt Please enter instruction then you can press 1 to arm Press 2 to disarm Press 3 to monitor or Press 4 to intercom If the password is incorrect you will hear a prompt voice Wrong password please re enter The system default operate password is 1234 Make sure to enter the password firmly by pressing and holding one digit at a time so you can hear a beep for each key press You may need to hold keys for half a second at a time Press 1 arm if fini
28. to store the last 30 alarm records Arm via the main unit panel remote controller or remote call by phone SMS alert of power failure and recovery Built in Lithium lon battery with automatic recharge 4 1 Introduction Install battery to all door sensors Remove insulated paper Transmitter 1 Use your right thumbnail to T pull bracket out a little bit 2mm Magnet A g 2 Using thumb and P hold both sides of the cover and pull up pL Open the cover and remove the insulated paper then close the cover Put small magnet next to sensor Install battery to IR motion sensor Install batteries and keep them switched off Know Your System brong 1 LCD Screen Resolution 128x64 English and Chinese display 2 LED Status Indicators POWER power and system activity indicator 5 fast flashing once per second system is searching for GSM signal slow flashing once per 3 seconds system is in ready mode SET is ON when the system enters setting mode SIGNAL wireless signal indicator used by wireless sensors ALARM is ON if any sensor triggers or sets off an alarm Touch Keypad Resistive Touch Panel requires gentle key pressing Do not press the keypad heavily as this may reduce its sensitivity ARM press to enter OUT ARM status gives you 40 seconds to leave home before system is armed STAY press to enter HOME ARM status deactivates all sensors with Home defense zone mode and a
29. ture all will corrupt the electronic circuitry Do not use or place the alarm system in dirty locations otherwise the electronic elements will be damaged Do no place the system in excessively hot locations High temperature will shorten the service life of electronic equipment damage batteries deform or even melt some plastic parts Do not place the system in excessively cold locations Otherwise condensation many occur and damage the circuit board of the alarm system It is recommended that you check and test the alarm system periodically Check the main unit panel every three months 1 Whether it can arm disarm normally 2 Whether it can dial the number for alarm normally 3 Whether it can receive wireless signals from detectors normally 4 Whether the back up battery is self recharging normally 63 Check the wireless detectors once a month 1 Trigger wireless detectors to ensure that the system can alarm normally 2 Check all detector sensor batteries to ensure that the all have good voltage levels 3 Check whether wireless detectors can send signal to the main unit panel normally Check the SIM card 1 Check the SIM card network signal credit balance etc 2 Make sure the PIN code verification of the SIM card is disabled 3 Keep the password and SIM card number safe to prevent others from remote controlling the system without permission Since the alarm system is continuously in operation or standby
30. u can re record until you are satisfied with the message Operation figures Fig 1 enter record setting Fig 2 you ll see this menu Start recording Fig 3 press 6 to choose play 33 3 18 Setting System Date The date format is MM DD Y Y YY setting is from 00 99 Method enter Time menu and then choose Date Input the exact date you want to set and press ENTER to confirm Operation figures eA Pa 00 00 00 Please enter 34 3 19 Setting System Time Time in this alarm system is 24 hour system Enter Time menu you will see Date menu then press 6 to choose Time Input the exact time you want to set and press ENTER to confirm Operation figures Fig 3 press 6 to choose time 11 12 12 l Fig 5 press ENTER to save Please enter 00 00 35 3 20 Scheduling Timely Arm This feature is also called Timely Arm After setting the required arm start time the alarm system will arm itself at the pre set time Note disable the timely arm just set time over 24hours e g 24 03 this function will disable Method enter Time menu you will see Date menu then press 6 to choose Timely arm Input the exact time you want to start the arming period and press ENTER to confirm Operation figures ae Ae Fig 4 input the tim
31. umber Input phone number Set user ID enter the Network Centers menu and the Phone Center menu Press Key 6 to move right to choose the User ID menu and 30 press Enter Input the user ID press Save key to save it The detailed operation diagram is as follows Diagram1 Enter Network Centers menu Diagram2 Choose user ID and confirm No number Diagram4 Save the user ID 1234 Input user ID Upload system arming disarming report to the network center enter Network centers menu and then enter the Phone Center menu Press Key 6 to move right to choose the Arm Report menu and press ENTER key to enable disable this function 31 The detailed operation diagram is as follows Diagram1 Enter Network centers menu Diagram2 Choose Arm report menu Disable Diagram3 Choose to enable disable the function of arm report Enable 3 16 Voice Recording This system can make 10 second voice recording for user to give out instructions to emergency services when the system is triggered Method enter record setting and start by choosing Start recording and immediately start recording your voice message The system will stop recoding after 10 seconds Operation figures Start recording 3 17 Voice Recording Replay Enter Recording setting and then press 6 to choose Play The main unit panel will start playing the voice message you have recorded Yo
32. usant nati Boa epe tide 61 5 TECHNICAL SPECIFICATIONS ones 62 6 CARE AND MAINTENANCE rmsnnnnnurnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnne 63 Main Features 0940 0994 099499 09499 9 Quad band worldwide cellular phone 900 1800 850 1900 MHz Elegant touch keypad with easy to use detailed menu system 128x64 lattice LCD screen with clock display English Chinese 4 wired and 10 wireless 433MHz defense zones each wireless zone supports up to 10 sensors Support for up to 8 remote controllers Built in loud speaker and intelligent voice announcer Auto play 10 second pre recorded voice message on alarm useful for giving address GPS position to emergency services Up to 6 phone numbers to dial out on alarm Up to 3 SMS numbers to send SMS to when alarm Remote control by phone to arm disarm or intercom listen in One touch control ARM out arm STAY home arm via touch keypad or arm and disarm via remote controller or telephone 4 Arm Modes out arm home arm delay arm and timely arm for scheduling arm disarm times 8 Defense Zone Places SOS fire gas door hall window balcony and boundary 4 Arm Delay Modes Real time immediate 01 99 second delay 24 hours always armed even if system disarmed Disable Alarm calls have priority over all other calls if the device is busy Direct wireless coding of any additional wireless accessories Alarm History

GSM06 User Manual - PiSector Home Security Alarm Systems

Contents

Download Pdf Manuals

Related Search

Related Contents