Manual Quick Guide ALC
Contents
1. operate the eguipment Statement FCC S 15 19 This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Canada CNR Gen Section 7 1 3 This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the follow ing two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radioexempts de li cence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouil lage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Contains Transmitter Module FCC ID SP3 86010156 IC 5530A 86010156 ifety Instructions NOTICE The disposal of this product should be effected according to all national laws and regulations NOTICE The power supply for charging or powering the ALC are designed for indoor use only NOTICE Only operate the power supply for charging or powering the ALC using the main voltages indicated on the ALC data she2. Ouick Guide ALC Antenna Line Configurator KATHREIN Antennen Electronic Content Gontenbe om ennuste to SRI mtm 2 SEIS MUONION re ee ee ende TR S Lee ee 3 pil a ee Re 3 General INStrUCtiONS ee ee ee 3 Mams Tead MR NER OTT E H 3 OCT eke cen cacti E E net A EH recep A nene ges ae ccm Naa art AUKIO EIT ja Stan aeon Maa 4 Safety INSITUCHON See ee UN ko AI to PININ haa eta er 5 Reg latory Compliance en er ee ee 6 Connection Example ea nee Re ee m 8 Int rfaces and Signalling ei te een seen ee 10 yl AOL ON PJ IA ee ee ee ee ee era es 11 Connectio PC laptop reren E mcm 12 Ic R7 gegen apes TE RR RT 19 Riz i o T 14 FOL your Nole MT I c 15 Safety Instructions Definitions Indicates a potentially dangerous situation Death or severe injuries may occur NOTICE Provides information on ensuring the safety of persons or objects General Instructions The details given in the quick guide and the prduct documentation must be carefully followed during the installation and operation of the ALC read the quick guide and the ALC product docu mentation thoroughly before connecting the ALC to the power supply The quick guide has to be used in combination with the ALC product documentation ALC Documentation delivered with each ALC The installation team must be properly qualified and also be famili
3. ar with the relevant national safety regulations Non observance of these instruc tions may damage or destroy the devices Death or severe injuries may occur Before you work on any equipment be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents Only trained and qualified personnel is allowed to install replace or service this equipment Use only the power supply included in delivery to charge or power the ALC Do not work on the system or dis connect cables during pariods of lightning activity The plug socket combination must be accessible at all times as it serves as the main discon necting device Non observance of these instructions may damage or destroy the devices Death or severe injuries may occur Mains Lead The device is battery powered Make sure that the device is undamaged Never put the device into operation if damaged This can jeopardize the electrical safety of the ALC Make sure that the power supply lead for charging or powering the ALC is undamaged Never put the ALC into operation if the mains lead is damaged Make sure that only the original in the scope of delivery power supply is used This can jeopardize the electrical safety of the ALC Co FCC Statements Warning Statement FCC S 15 21 Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to
4. ction class IP 54 Temperature range operating Temperature range charging 20 45 C ambient temperature 0 30 C ambient temperature Dimensions H x W x D 265 x 102 x 37 mm Packing size 400 x 280 x 85 mm Power supply LiPo battery 14 8 V gt 2000 mAh Tightening torque for fixing the connector must be 0 5 1 0 Nm hand tightened The connector should be tightened by hand only Switchable with software Certificate Standards Scope of supply www kathrein de KATHREIN Werke KG Anton Kathrein StraBe 1 3 P O Box 10 04 44 CE FCC part 15 class B UL for external power adapter EN 60950 22 EN 55022 EN 55024 ALC Charging device can also be used as external power supply USB cable RET cable HF cable SMB 7 16 Quick Guide Transport case 86010156 83004 ROSENHEIM GERMANY Phone 49 8031 184 0 Fax 49 8031 184 820 Page 1 of 1 For your Notes For your Notes Internet http www kathrein de KATHREIN Werke KG Phone 49 8031 184 0 Fax 49 8031 184 494 Anton Kathrein StraBe 1 3 P O Box 10 04 44 83004 Rosenheim Germany 936 4423 b 0413 VKDT Technical data subject to change KATHREIN Antennen Electronic
5. d by this disclaimer Although the design and implementation of the ALC which was developed for the Kathrein RET system were carried out very carefully the KATHREIN Werke KG cannot guarantee the faultless operability of the product Both the software and hardware are provided as is and the use of the ALC is at your own risk Under no circumstances can the KATHREIN Werke KG be held responsible for any unforeseen damage as a result of the use of the ALC In particular this is valid if any direct indirect incidental conseguential or special damage occurs inclusive of the loss of profit or data This disclaimer remains valid even if authorised representatives of the KATHREIN Werke KG were informed by you on any possible damage We re serve the right of modifying the ALC without notice This ALC is the property of KATHREIN Werke KG It must not be sold or made available to a third party nor must it be copied This limitation may not apply if an alternative agreement has specifically been made with the KATHREIN Werke KG The KATHREIN Werke KG is registered in the companies register HRA 460 district court Traunstein Germany Copyright c 2012 KATHREIN Werke KG All rights reserved S Java COMPATIBLE Java is a registered trademark of Oracle and or its affiliates 13 Data sheet Subject to alteration 936 4424 b 14 Antenna Line Configurator ALC For Antenna Line Devices ALD Antenna L
6. et NOTICE Non observance of these instructions may result in unsuccessful operation of the RET components or destruction of the devices NOTICE For installing and servicing the RET system follow the instructions in the RET installation manual NOTICE This device contains a lithium polymer battery It is not allowed to open the device in any case For service repair or for disposal of the device please send it to the service address given on page 14 in this quick guide NOTICE RETAIN THESE INSTRUCTIONS OT Regulatory Compliance FCC Class A and Class B Statements NOTICE This section lists the Class A and Class B statements for the Kathrein ALC Antenna Line Configurator The information for users of Class A products is included in this section in the event that EMC perfor mance is degraded due to the addition of a Class A product This product has been tested and verified to meet Class B requirements as defined in CFR 47 part 15 for the United States an in EN55022 as well as CISPR 22 for Europe and other international market places This product has been tested in its customer orderable and shippable configuration including certain port adapters and accessories representative of typical customer applications and meets Class B requirements If you add any additional accessories or other features to this product that are tested and meet require ments that are less than Class B i e Class A then the product may as
7. ine Configurator Type No Connector to RCU TMA KATHREIN Antennen Electronic 86010156 1 x 8 pin connector according to IEC 60130 9 female conforming to AISG RF connector SMB male 20 30 V DC A GLOBAL INITIATITI Input voltage of ALC Display Touchscreen sunlight visible Tiltsensor Measuring range 80 accuracy t1 Output voltage to RCU s TMA s AISG female pin 6 24 V DC 20 30 V DC AISG female pin 1 12 V DC 10 15 V DC RF male at 24 V DC 10 30 V DC RF male at 12 V DC 10 15 V DC Output power power supply to RCU s TMA s AISG female pin 6 24 V DC without load on pin 1 12 V DC and on RF plug x 15 W AISG female Pin 1 12 V DC Narren with max 7 5 W load on pin 6 24 V DC and or on RF plug lt 7 5 W Current monitoring measurement level Per branch 12 V 24 V RF 10 1500 mA Over current protection Per branch 12 V 24 V RF 1500 mA Interface to RCU TMA Protocol to RCU TMA RS 485 power supply RF connector SMB male HDLC hex coded command set conforming to AISG 1 1 and 3GPP AISG 2 0 Interface W LAN 802 11n USB 1 1 2 0 Max number of RCU s TMA s 9 1 pcs depending on system configuration and length of control cable Max length of control cable 200 m 9 RCU s in daisy chain configuration 150 m 6 RCU s in splitter configuration Internal memory 380 MB Weight 1 kg Prote
8. it may cause interference with radio and televi sion reception has been tested and found to comply with the limits for a Class B digital device in accor dance with the specifications in part 15 of the FCC rules These specifications are designed to provide reasonable protection against such interference in a residential installation However there is no guaran tee that interference will not occur in a particular installation You can determine whether your equipment is causing interference by turning it off If the interference stops the equipment you turned off was probably causing the interference If the equipment causes interference to radio or television reception try to correct the interference by using one or more of the following measures Turn the television or radio antenna until the interferences stops Move the equipment to one side or the other of the television or radio Move the equipment farther away from the television or radio Plug the equipment into an outlet that is on a different circuit from the television or radio That is make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses Modifications to this product not authorized by KATHREIN Werke KG could void the FCC approval and negate your authority to operate the product Regulatory Compliance FCC Class A and Class B Statements NOTICE The ALC is CE accredited and thus in compliance with
9. sume the behavior and charac teristics of a Class A device Class A products produce more RF emissions than a Class B product and may cause allowable interference to other products FCC Compliance for Class A Equipment Modifying the equipment without Kathrein s authorization may result in the equipment no longer comply ing with FCC requirements for Class A or Class B digital devices In that event your right to use the equipment may be limited by FCC regulations and you may be required to correct any interference to radio or television communications at your own expense For Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause harmful interference to radio communications Operation of this equip ment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at this own expense FCC Compliance for Class B Equipment The Antenna Line Device ALC generates and may radiate radio frequency energy If it is not installed in accordance with Kathrein s installation instructions
10. t data receive data 9 Yellow coloured if charger connected 10 Green coloured if battery is charged 10 Initial operation Operating the unit With touch pad With web browser When you switch on the ALC for the first time you will see a display where you can enter the current date time Installer ID and company name After confirming your entry by pressing the Set data button the unit will now always begin with the standard start screen Connect the ALDs to the ALC with a AISG cable RF cable with an SMB plug and Bias Tee afterwards press the button Connect to ALD to start the scan procedure Over the Menu button you can access the main menu and then move on to perform further tasks as soon as scanning is successfully completed The ALC must be fully charged prior to operation The ALC can be operated with the builtin touchpad The unit can also be operated using a Web Browser via PC Notebook or Tablet 11 Connect to PC laptop The ALC can also be operated conveniently from a PC or notebook using a modern browser interface There are two modes of connection to the ALC available for this purpose Using the USB connection instructions for Windows 7 32 bit 64 bit Connect the ALC to the PC Notebook using the USB cable supplied Switch on the ALC A pop up dialogue appears headed Driver Software Installation If automatic updates are activated please wait until the search for drivers has been comple
11. ted no drivers will be found for RNDIS Press Close to close the pop up dialogue On the CD drive go to the Kathrein ALC directory and execute the file setup exe setup64 exe Confirm dialogue field User Account Control with Yes Respond with Yes to the dialogue Do you want to allow the following program from an unknown publisher to make changes to this computer Respond with Yes to the dialogue Kathrein ALC USB network driver installer In the dialogue Windows Security press the Install button It takes approx 30 sec for installation to be completed Respond with Yes to the message Kathrein ALC USB network driver installer successfully installed When installation has been performed successfully the device Linux USB Ethernet RNDIS Gadget must appear in the Device Manager under Network adapters The ALC can then be operated via the web browser by inputting the address usb alc kathrein Using the WLAN connection instructions for Windows 7 Activate the WLAN in the Networkconfiguration menu on the ALC If you have not already done so also activate the WLAN on the PC Notebook kathrein alc lt serialnr gt must appear in the available Wireless Network Connection lt serialnr gt stands for the serial number that appears on the back of the device Select kathrein alc lt serialnr gt and click on Connect In the dialogue Connect to a Network input the security ke
12. the essential requirements of the European Regu lations 89 336 EWG electromagnetic compatibility and 73 23 EWG low voltage directive Connection Example 1 Connection with the RET system 1 1 Using Standard Control Cables Connect the AISG interface on the upper panel of the ALC to the RCUs This can be done with a standard AISG control cable scope of supply directly to the RCU fig 1 or using one Smart Bias Tee and a TMA fig 3 1 2 Using SMB Control Cables Using the HF connector the connection with the RET system can be done with a SMB control cable scope of supply and a Bias Tee fig 2 near the BTS and a Smart Bias Tee ANTENNA SMBIHF 2 176 MHz Connection Example 2 Optional operation 2 1 Using power supply The ALC can also be operated with the delivered power supply 2 2 Using USB and a PC Notebook to operate the ALC via a Web Browser based application 2 3 Using W LAN and a separate device to operate the ALC via a Web Browser based application 80 264VAC dr 63Hz Interfaces and Signalling Interfaces on the bottom panel Interfaces on the upper panel 1 Power on off 5 WLAN antenna HF 2 Mini USB interface for PC connection 6 Interface to RCU 3 USB interface for Memorystick RS 485 4 24 V interface for 24 Ve power supply 13 5 V output voltage 24 V output voltage 7 HF connector SMB male Signalling on the frontside on off 8 Data TX RX transmi
13. y kathreinalc and confirm it with OK When authentication has been successful kathrein alc lt serialnr gt must be shown as connected in the display of available Wireless Network Connections The ALC can then be operated via the web browser by inputting the address alc kathrein Note If the web browser fails to establish a connection with the ALC the proxy settings in the web browser should be deactivated e If conflicts arise regarding the name resolution the set IP address can be used as an alternative the pre set addresses are 192 168 0 1 USB and 192 168 1 1 WLAN Further instructions 12 A detailed description of the applications and functions of the ALC can be found in the user manual The user manual can be called up as follows e directly via the internet interface User Guide button e in the internal memory of the ALC drive Kathrein ALC gt user guide paf Service Contact Addresses For all marketing and technical inquiries Fax 49 0 8031 184 820 E Mail mobilcom kathrein de For Service and Repair Kathrein Werke KG Department QR Anton Kathrein Stra e 1 7 83101 Rohrdorf Updates You can download the current firmware from the Kathrein website www kathrein de Information on software updates for the ALC are found in the manual Disclaimer All Kathrein software and hardware products in conjunction with the Antenna Line Connector ALC are covere
Download Pdf Manuals
Related Search