Owner`s Manual - Hot Tub Covers Canada Hot Tub Covers Canada
Contents
1. B E gt f i j N 1 i W Barb fittings 3 4 straight and right angle Tube crimp for 3 4 tubing 2 PVC Threaded 1 plug O O N O A Pipe clamp for 1 PVC 10 LaMotte test strips salt and general spa TROUBLESHOOTING It is always a good idea to revisit the user manual to make sure installation or maintenance steps were not overlooked before referring to the trouble shooting section Plates Need Cleaning Cleaning the Electrode Cell White Calcium Deposits e If there is a white calcium buildup between the titanium plates this will interfere with the chlorine production Disconnect the power before cleaning Soak the cell in a mild acid white vinegar or pH down for 10 to 30 minutes and rinse in clean water Repeat until the white deposits are gone e For the ChlorMaker IL if shutoff valves were installed turn them off and remove the electrode from cell housing See ChlorMaker IL parts item 1 on the previous page using a suitable wrench If valves were not installed remove the electrode and quickly plug the hole with the supplied 1 plug item 8 to keep the spa water from leaking out After the plates are clean apply Teflon tape and reinstall the electrode into the cell When done make sure there are no leaks RED Lights While Making Chlorine e Salt level low Add salt Before adding salt it is a good idea to measure the salt level first e Check the cell for white calcium buildup and if present clean the pl2. www controlomatic com PRODUCT REGISTRATION Either register your ChlorMaker online at www controlomatic com of fill out the information below and mail it to ControlOMatic 12659 Arbor Ln Grass Valley CA 95949 If purchased directly from ControlOMatic you will already be registered Serial ChlorMaker IL LIDO Number irst Name Last Name urchased From ddress ity State Postal Code hone Email
3. 24 hour pump the ChlorMaker IL can be a challenge to install and isn t recommended for the following reasons 1 Installation Steps for the ChlorMaker IL cell 1 10 When the cell E is removed for cleaning or during installation Locate the continuous 24 Hour circulating pump and the 3 4 Connect Tubing To Cell Cut the existing tube and reconnect The chlorine production will be unpredictable the main pump is typically not on the same amount of time per day The existing pump time will need to be increased to give the ChlorMaker IL enough time to make the needed amount of chlorine this will lead to higher energy costs There will not be a suitable location to install the cell a bypass will be needed from the main plumbing The power supply will need to be controlled with the same voltage that turns on the circulation pump You do not want the ChlorMaker IL making chlorine when there is no water flow because gasses will accumulate in the plumbing Open the spas equipment panel Turn the SPA off at the circuit panel tubing connected to the pump If the pump has a different size tubing adapters will be needed The cell has 3 4 NPT female threads _ Install the ChlorMaker IL cell on the OUTPUT side of the pump The tube will need to be cut and reconnected to the ChlorMaker B IL cell Additional tubing may be needed if the existing tube is not long enough or is hard to access The location of the cell should have
4. Level Salt High Count Flashes Salt OK Level 1 to 10 Salt Low Made in the USA by ControlOMatic it ar ie d ii 9 Bo gt So y PERE x A rA an yee hey N Gy ej t pes b r i NT T Ti be p e meas bet Siw i Se je ae 4 rary a Kq Sesto EN OE RO Mer RST Fg eLa Po k ie i A IN Ne pane an ete See Ae Seat PEE x et TA i Ne LAS e 2 1 1 i 4 4 F s pF i pme 1 Dae ks 5 OPERATION The ChlorMaker has 3 buttons and 4 lights built into the overlay on the control box With the buttons you can check the power level change the power level and put into boost mode The lights indicate the salt level and the current mode making chlorine or standby Power Up To turn on the ChlorMaker plug in the power supply wall transformer When the ChlorMaker turns on it will flash the lights as follows 1 WHITE Blinks two times 2 RED BLUE GREEN will flash in that order 3 WHITE will then flash the power level count the flashes the number is the power level 1 to 10 4 Chlorine production will start after a few seconds Making Chlorine Salt Level Indication Chlormaker will indicate if the salt level is low or normal If it is low that is OK you could add more salt if you want but not required If the lights are on solid or blinking at a one second rate the ChlorMaker is producing chlorine e Solid GREEN Salt Level High e Solid BLUE Salt Level Normal e Solid RED Sal
5. according to the following table To activate Boost Mode simply press the Boost Mode Button The Salt Light will begin flashing indicating that ChlorMaker is in Boost Mode IMPORTANT The ChlorMaker can t make chlorine faster The Boost Mode keeps it on for a longer period of time If the spa chlorine has dropped to 0 PPM from heavy usage chlorine may need to be added Power Level Normal Time Boost Mode Time Power Level Normal Time Boost Mode Time 00 02 00 00 07 30 00 15 00 00 30 00 00 45 00 00 12 00 00 45 00 01 30 00 03 00 00 04 30 00 01 00 00 01 30 00 02 00 00 02 30 00 03 00 00 06 00 00 09 00 00 12 00 00 15 00 00 15 00 00 ChlorMaker Included Parts When opening the package make sure all of the parts for the appropriate model are included Both models ChlorMaker DO Eei include this owners manual and the serial number a n Bees should be on the control box and on the last page of 9S this manual i o ChlorMaker DO Included Parts 1 Cell with 10 foot cable 2 3 4 5 6 Power supply with 15 foot cable ChlorMaker control box Cable clips 2 SS Screws 6x1 2 6x5 8 2 of each LaMotte test strips salt and general spa ChlorMaker IL Included Parts 1 Cell with 10 foot cable FY ChlorMaker IL A AN ChlorMaker Power supply with 15 foot cable ChlorMaker control box Cable clips 2 SS Screws 6x1 2 6x5 8 8x1 2 of each A W N i i E e t My
6. no obstructions at the cable 4 a ee end of the cell This is to allow for cell removal replacement and cleaning Water shut off valves not included may be installed at D to aid in future maintenance and cleaning of the cell Install the two pipe brackets A 6 with the two larger screws 5 A suitable location also includes an appropriate mounting surface for the screws Do not install the brackets to insulation Install the two 3 4 barb fittings 4 to the cell using Teflon tape The cell should be mounted vertically to prevent chlorine gas from being trapped inside the cell Based on the location of the install decide if the 90 degree barb fitting should go on the side or the top B and C the ends to the two 3 4 barb fittings on the cell Use the supplied clamps 2 at B and C to securely fasten the tube to the barbs on the cell Note that some water will spill from the cut tube even though the spa has been drained or shut off The cell cable F needs to be routed to the ChlorMaker box The cable can be routed under the spa skirt to the outside of the equipment area To further conceal the cord a small hole can be drilled below the ChlorMaker box where the cell cable exits and the cable can be removed from the ChlorMaker box requires removing the box and the mounting flange and routed through this small hole use the 1 plug 1 to seal the hole ChliorMaker Spa Saltwater Chlorine Generator Power
7. of salt directly into the spa water to bring the concentration to the recommended level Turn the spa jets on If the water is cold it may take several hours for the salt to fully dissolve warmer water will help dissolve the salt faster NOTE It may take the ChlorMaker a few hours to register the salt level the first time Wait a couple of hours for the salt to dissolve and then turn on the ChlorMaker NOTE When putting salt in do not add too much The ChlorMaker will shut down and display RED GREEN lights at the same time It is always better to put less in and then add a little more later if needed If you have a water softener then your water source may already have some salt in this case let the water get to temperature and turn the ChlorMaker on before adding any salt to check the current level NOTE If you are trying to decide which salt you want to use ControlOMatic recommends pool salt NaCl Sodium bromide NABR is around 13 per pound and pool salt NaCl is around 0 18 per pound To use NaBr on a 400 gallon spa would cost around 130 for the salt and then you would have to buy it again when you drain your spa ControlOMatic has also received feedback that the smell from Bromine is noticeable NOTE Many hardware stores and big box stores carry pool salt so it is easy to find 40 pound bags at such places ChlorMaker Installation Prepare the SPA Drain and clean the spa if required Refill and add salt Allow the water to
8. ChlorMaker ChlorMaker DO ChlorMaker IL Drape Over In Line OPERATING INSTRUCTIONS ControlOMatic Inc 12659 Arbor Lane Grass Valley CA 95949 www controlomatic com support controlomatic com 530 205 4520 Manual Version 3 30 15 Made in the USA IMPORTANT SAFETY INSTRUCTIONS READ amp FOLLOW ALL INSTRUCTIONS When installing and using this electrical equipment basic safety precautions should always be followed including the following WARNING Cutting the cord from the power supply to the ChlorMaker cell voids the warranty Damage will occur if the connection is reversed WARNING To reduce the risk of injury do not permit children to use this product unless they are closely supervised at all times WARNING Use ChlorMaker only according to these instructions Any modification or misuse of this product will void the warranty WARNING Install ChlorMaker in accordance with all national and local electrical plumbing safety and other applicable codes WARNING Connect ChlorMaker to a GFCI ground fault circuit interrupt or GFI ground fault interrupt protected VAC power source only WARNING Protect the power supply and outlet from exposure to the elements including direct sun rain snow condensation etc WARNING DO NOT use with extension cord Injury may result WARNING DO NOT operate ChlorMaker if damaged in any way WARNING DO NOT pull on the cord to disconnect the Power Supply from power source Do not a
9. ash every 10 seconds e The GFCI circuit breaker has tripped Verify that there is input VAC e The power supply has been damaged The rain cover didn t prevent moisture from the power supply was subjected to freezing weather or the cord has been cut LIMITED WARRANTY Models This warranty applies to ChlorMaker models referenced as System ControlOMatic Inc Warrants the system to be free of all defects in material and workmanship for one 1 year from the owners original purchase date The system includes the power supply unit cable electronics and electrolytic generator for residential use only The product must be installed properly and used in accordance with this manual and all applicable local codes and regulations This warranty is not transferable proof of purchase may be necessary Damage to the system from improper water maintenance is not covered in this warranty In no event shall ControlOMatic Inc be liable for consequential damages for breach of this warranty Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply The warranty does not cover any loss or damage to the product due to improper installation product abuse misuse negligence or improper maintenance of the system pool or spa The warranty does not cover any loss or damage to the spa spa components users or anything outside the system due to system failure Since Cont
10. ates e Plates damaged Unit needs to be replaced The plates will last 7000 to 10000 hours of chlorine production and the ChlorMaker may be at the end of its life Note The lower the power level you can operate on the longer the ChlorMaker will last Consistently Low Chlorine e Power level too low Increase the power level e Low salt level Adjust the salt level as necessary The ChlorMaker will make less chlorine with a lower salt level Plates need cleaning See above High bather load Additional chlorine or shock may be needed Very high salt level The RED and GREEN lights may be on indicating a very high salt level When this happens the ChlorMaker shuts down and will stop making chlorine to protect the power supply Drain out some of the water and refill with fresh water to lower the salt level Just doesn t keep up Remove organic material such as leaves and clean the filter Make sure the ChlorMaker DO cell is at the deepest point in the spa and in a VERTICAL ORIENTATION Remove the phosphates Phosphates are food for algae and consume chlorine The ChlorMaker makes chlorine slowly and removing the phosphates will help lower the spas chlorine consumption demand Shock the water You can use either a chlorine based shock or chlorine free Consistently High Chlorine e Power level too high Lower the power level The ChlorMaker ts off No Lights e Check if in the standby part of the cycle watch and see if the GREEN lights fl
11. d route the cable to the outlet do not plug in yet The cable should already be attached to the power supply the connector has 2 metal pins one is round and the other is rectangular and can only go in one way reversing the connection will damage the ChlorMaker The ChlorMaker includes 2 cable clips use one 3 16 with a 6 x 1 2 screw to attach the cable to a solid surface if necessary Cold Weather Operation The power supply is not designed for temperatures below 32 F or 0 C If this can t be avoided store the power supply in a warm location when the temperature is low or install the power supply in the spa equipment area where there is some protection Mount the Control Box Find a suitable location to mount the control box meeting the following requirements 1 Vertical installation with the two cables coming out the bottom 2 Out of direct sunlight 3 A location that will minimize rain and moisture Even though the box is waterproof minimizing moisture exposure will minimize the chance of moisture getting A A ___________ inside the box gt 11 4 A flat location on the spa skirt that is close enough for the power supply cable to reach the outlet and the ChlorMaker Mounting Screw Locations cable can be protected 5 Locate on a post or wall near the spa close enough to the spa for the 10 foot cell cable to reach with the cell hanging in the deepest part of the spa The ChlorMaker box mounting flange has
12. d salts are generally available at pool amp spa supply stores home improvement centers and On Line stores in a variety of sizes Never use rock salt or salts that have more than 1 anti caking agents yellow prussiate of soda or sodium ferrocyanide These compounds may cause surface staining BROMINE SALT SODIUM BROMIDE NaBr Raise Salt Level to 3 000 PPM Parts Per Million There are several manufacturers of Sodium Bromide Salt to choose from Please make sure the Sodium Bromide you purchase is 99 pure or better Ask your local pool and spa dealer for assistance Chart is Based on 100 Gallons or 379 Liters of Spa Water Salt Type Pounds kg Cups Salt Level 99 Pure Sodium Chloride NaCl 1 5 0 681 2 9 1500 2000 PPM 99 Pure Sodium Bromide NaBr Fine Grain Salt 2 9 nse 4 2500 3000 PPM The amount of salt to add and dissolve is dependent upon the size of the spa Determine the volume of water in gallons or liters by checking the spa owner s manual or use any Internet volume calculator e 99 Pure Sodium Chloride NaCl Coarse Grain Example e For a 350 Gallon Spa Divide 350 Gal by 100 and multiply by 2 5 to get the amount to add in cups e 350 100 2 5 3 5 x 2 5 8 75 Cups e For a 1250 liter Spa Divide 1250 liters by 379 and multiply by 0 681 to get the amount to add in kg e 1250 379 0 681 3 3 x 0 681 2 25 kg and for cups 1250 379 3 3 x 2 5 8 25 cups Simply pour the recommended amount
13. e product Use the included test strips to measure water chemistry and verify that the water is properly balanced Replacing the filter is recommended but not required unless the spa was previously sanitized with a hydrogen peroxide system The combination of hydrogen peroxide and chlorine may cause gum like build up water discoloration and skin irritation It is important to properly maintain your spa for the health and safety of its users Spas are unique in both size and usage patterns ChlorMaker will significantly reduce the amount of spa maintenance required but regular chemical checkups including chlorine levels and pH are recommended Proper water maintenance will prolong the life of ChlorMaker and the spa The following table describes generally accepted optimum water chemistry for portable spas It is recommended that chlorine and PH levels are checked before each use or at least once per week when not in use Alkalinity Calcium Hardness and Free Chlorine 2 0 to 3 0 Salt Concentration should be checked at least once per month It is recommended that the spa is 8 210 7 6 manually shocked after high usage example after a Total Alkalinity 80 to 120 PPM party with multiple users or biweekly if used frequently Always remember to leave the spa Calcium Hardness 200 to 400 PPM circulating for several hours before retesting Phosphates in the spa water will increase the demand for chlorine and will reduce the life expectancy of t
14. get to over 95 F and balance the water Installation Steps 1 Electrical outlet if not already available near the spa for the Power Supply 2 Mount the control Box The ChlorMaker DO cell simply drapes over 4 The ChlorMaker IL cell needs to be installed into the spas plumbing 5 Turn the ChlorMaker on 6 Set the power level Power Supply The power supply supports 100 to 240 VAC with an output voltage of 5 5 VDC The supply cord from the Power Supply to the ChlorMaker control box is 15 feet Installing any equipment inside the spa equipment compartment may void the spa warranty or void the safety certification of the Spa and is not recommended 110 VAC Electrical Outlet Locate a GFCI protected outlet near the spa WARNING A 110 VAC GFCI or GFI protected outlet is required A weather protective cover is required to house the power supply at the power source connection Weather protective covers are available at most local hardware stores If an outlet needs to be installed have a licensed electrician add a 110 VAC GFI protected outlet 220 VAC Electrical Outlet The power supply plug style is for 110 VAC Have a licensed electrician install a 220 VAC GFI protected connection near the spa that will accept a 110 VAC style plug The outlet may need to be a minimum distance from the spa and the local electrical codes should be checked a Power Supply Connector Remove the tie straps from the ChlorMaker power supply cable an
15. he generator Remove Phosphates upon start up and each month there after Phosphate Remover can be purchased at any local Pool amp Spa supply store WARNING Consistent chlorine levels above 5 0 PPM parts per million or consistent salt concentration levels above 5 000 PPM may lead to corrosion of metal components in the spa WARNING Consistently low Calcium Hardness levels below 150 PPM may lead to spa equipment damage and failure Make sure Calcium Hardness levels are within the recommended range above SALT REQUIREMENT ChlorMaker will generate either Chlorine or Bromine depending on the type of salt it all depends on which sanitizer you prefer Use Sodium Chloride Salt if you prefer Chlorine Generation or Sodium Bromide Salt if you prefer Bromine Please Note Each salt requires a different level of salinity for the ChlorMaker to operate effectively WARNING SALT ONLY NEEDS TO BE ADDED ONCE AND BROUGHT TO THE APPROPRIATE SALT LEVEL BLUE LIGHTS PER SPA WATER CHANGE DO NOT KEEP ADDING SALT CHLORINE SALT SODIUM CHLORIDE NaCl Raise Salt Level to 1 500 to 2 000 PPM Parts Per Million Approved salts include pool salt made for salt water chlorine generating systems canning and pickling salt from your local market and some water softener salts that are 99 pure sodium chloride or better Some high end mineral enriched salts can be used but require higher quantities to achieve 2 000 PPM sodium chloride salt level These approve
16. he size of your spa I3 lt 200 lt 760 Day 2 Measure the chlorine level If it is higher than you Power Level Gallons Liters want lower the power level by 1 If it is lower than the level A 200 to 300 760 to 1150 you want raise the power level by 1 Day 3 Repeat the Day 2 step until the chlorine remains 9 SODO AIO LLAU USOC constant at the required level for a couple days 6 400 to 500 1500 to 1900 NOTE If the chlorine level is 0 PPM 24 hours after 7 gt 500 gt 1900 installation the initial chlorine demand on the spa may be above what ChlorMaker can produce in order to break away from zero In this case manually add chlorine or shock according to the product label to assist in the initial set up If soa usage drops vacation winter etc it is important to lower the power level down several levels If usage significantly increases return from vacation etc it is important to adjust the power level up accordingly Always retest and adjust the power level as needed WARNING The ChlorMaker does not measure the sanitizer level and the power level needs to be properly adjusted If the power level is higher than needed and the spa is left alone for a number of days without measuring the sanitizer the levels may be too high and potentially damage spa components Boost Mode amp Power Level Times Activating Boost Mode will take ChlorMaker out of regular production mode or standby mode and re start the production of chlorine
17. llow the cord be walked on or to rest on sharp edges or corners Do not drop throw or otherwise rough handle ChlorMaker WARNING DO NOT operate or leave the power supply in temperatures below 32 F or 0 C The power supply may not survive in extremely cold temperatures WARNING Disconnect remove and store ChlorMaker indoors when spa has been winterized or drained CAUTION Leave spa cover open at least 1 minute to allow trapped gases to escape prior to use CAUTION Measure water quality parameters and adjust if necessary prior to each spa use CAUTION ChlorMaker doesn t measure the chlorine level and must be adjusted properly in order to not over chlorinate your spa Over chlorination can lead to spa damage and un healthy water conditions Additional ChlorMaker DO Drape Over Warnings WARNING Remove the ChorMaker DO cell from the SPA when using the SPA WARNING DO NOT handle the ChlorMaker DO cell during chlorine production visible bubbling Slight discomfort may be felt in cuts sores or sensitive skin areas due to chlorine concentration and the electrolysis process WARNING DO NOT insert objects into or tamper with the ChlorMaker DO s cell in any way Inserting metal objects into the body may cause damage and void the warranty SAVE THESE INSTRUCTIONS INTRODUCTION ChlorMaker is a semi automated salt water chlorine generation system specifically designed for portable spas up to 1000 Gallons ChlorMaker generates ch
18. lorine from a small amount of ordinary salt Sodium Chloride NaCl dissolved in the spa water The amount of salt added is very small in relation to the volume of the water in the spa The concentration required for the ChlorMaker is only about 5 of the salt level of ocean water and below the typical taste level of most humans The small addition of salt also benefits spa users by providing a softening effect on the water leaving hair and skin feeling smoother and healthier than with traditional sanitizing products Only 2 5 cups of salt per 100 gallons 379 liters of water is all it takes for ChlorMaker to produce fresh pure chlorine leaving your water clean and clear day after day ChlorMaker produces chlorine in its pure form using electrolysis in order to sanitize the spa water The ChlorMaker operates on a 3 hour cycle The chlorine in a spa will dissipate quickly due to the warmer temperatures of the water so the ChlorMaker operates with a short 3 hour cycle time to ensure sanitizer levels are maintained After the salt is converted to chlorine the chlorine will later be converted back to salt keeping the salt level steady When you use the spa your body attracts some salt and when you get out the salt level will drop slightly WATER PREPARATION amp MAINTENANCE To ensure proper operation the spa must be drained rinsed refilled with fresh water and balanced to the recommended levels indicated in this section before installing th
19. rolOMatic has no control of the use of this system the purchaser assumes all responsibility for using the system This warranty does not apply to any costs repairs services damages claims or losses for all of the following Service calls to install re install or correct the installation of the product or to explain the usage of the system to the buyer repairs necessitated by use other than normal home use damage resulting from misuse unintended use unforeseen use non pool or spa use abuse accidents alterations improper installation or corrective work necessitated by repairs made by anyone other than an authorized service technician THE FOREGOING WARRANTIES ARE CONTINGENT ON THE PROPER USE OF THE SYSTEM IN ACCORDANCE WITH THESE INSTRUCTIONS AND SPECIFICATIONS AND SHALL NOT APPLY TO ANY SYSTEM THAT HAS BEEN REPAIRED OR MODIFIED BY PERSONS OTHER THAN THE MANUFACTURER THE EXPRESS WARRANTIES SET FORTH IN THIS AGREEMENT ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED MANUFACTURER HEREBY SPECIFICALLY DISCLAIMS ANY OTHER REPRESENTATIONS OR WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE INNO EVENT WILL MANUFACTURER S LIABILITY FOR ANY CLAIM WHETHER IN CONTRACT TORT OR UNDER ANY OTHER THEORY OF LIABILITY EXCEED THE AMOUNT NECESSARY TO REPAIR OR REPLACE THE COVERED SYSTEM Should any problem develop during the warranty period contact ControlOMatic
20. shes Each flash represents a power level For example 3 flashes power level 3 7 flashes power level 7 CHANGE POWER LEVELS Press both the UP arrow and the DOWN arrow at the same time The Light will turn on solid indicating that it is in power change mode Press the UP arrow to increase power the GREEN light will flash each time the UP arrow is pressed If set at the maximum power level of 10 the GREEN light will be on solid Press the DOWN arrow to decrease power the RED light will flash each time the DOWN arrow is pressed If at the minimum power level of 1 the RED light will be on solid When finished do not press any buttons for 3 seconds The light will flash count the flashes confirming the new power level setting SELECTING THE RIGHT POWER LEVEL Selecting the right power level requires some testing and adjustment There are many factors that affect the sanitizing needs of a spa such as Frequency of spa use number of people if there is an Ozone Generator spa temperature last drain and refill phosphate level etc After the testing and adjustment period ChlorMaker will take care of your sanitation needs day after day As a starting point set the power level to the general recommendations shown in the chart below This is only a starting point and the final level may be very different Use the following procedure to find the power level for your spa Day 1 Set the power level according to the table and t
21. t Level On The Low Side e Solid RED GREEN at the same time Salt Level has exceeded the maximum and the ChlorMaker has shut down to protect the power supply and the cell Drain out some water and refill to dilute the salt level e The lights will blink the salt level when in boost mode Not Making Chlorine Standby Mode The ChlorMaker works on a 3 hour cycle The first part of the 3 hours is chlorine production mode where there will be visible bubbles coming out of the cell the rest of the 3 hours is standby mode where the cell is not making chlorine The standby mode is indicated by the GREEN light flashing every 10 seconds This shows the ChlorMaker has power and is on but waiting for the 3 hour period to end Power Levels ChlorMaker includes 10 power level settings that are set based on water volume usage and testing The ChlorMaker factory setting is 3 on 15 minutes and standby is 2 hours and 45 minutes The output power to the cell is always the same The power levels change the amount of time the cell is energized every three hours At the start of the three hour period the cell will be energized and then after the time indicated by the power level the cell will go into standby mode and stop producing chlorine At the start of the next 3 hour period the cycle repeats Follow the steps below to increase or decrease the power level VIEW THE CURRENT POWER LEVEL SETTING Simply press the UP or DOWN arrow button once and count the fla
22. two large holes allowing for installing the screws first 1 Install the two small screws 5 3 8 apart and 1 1 4 or more below the edge of the shell part of the spa 2 Place the box onto the screws and slide the box down 3 Tighten the screws ChlorMaker DO Cell Lift the lid off the spa and drape the cell over the side into the water Use the following guidelines for the placement of the cell 1 For best results place the cell in the deepest location in the spa When generating chlorine the bubbles will travel up and if in the deepest location in the spa will be in contact with the spa water longer 2 The cell must be in a vertical orientation If lying flat it will generate less chlorine 3 The cell can be located in the filter area if it will fit but this is not recommended This is less desirable as the bubbles will not be in contact with the water as long as a deeper location and when the pump is off the chlorine level will be much higher in the filter area because the filter door closes when the pump is off 4 The ChlorMaker DO includes 2 cable clips Use one of the clips 1 4 clip and a 6 x 1 2 screw to fasten the cable to the side of the spa if necessary ChlorMaker IL Cell The ChlorMaker IL requires an existing circulation pump in the spas equipment area that is on 24 hours a day These pumps are very small and usually have 3 4 vinyl tubing which makes installation relatively easy If there isn t a
Download Pdf Manuals
Related Search