Home

DVR User Manual

1. eeecooo0000000000000000000000000000000000000000000000000000000000000 60 1 1 1 1 2 HD TVI DVR User Manual Introduction DVR Introduction This model is standard 4 8 16 CH 1080P 720P 960H high resolution DVRs which adopts high performance video processing chips and embedded Linux system Meanwhile it utilizes many most advanced technologies such as standard H 264 with low bit rate Dual stream SATA interface VGA output mouse supported IE browser supported with full remote control mobile view by phones etc which ensure its powerful functions and high stability Due to these distinctive characteristics it is widely used in banks telecommunication transportation factories warehouse and irrigation and so on Main Features COMPRESSION FORMAT o Standard H 264 compression with low bit rate and better image quality LIVE SURVEILLANCE o Supports HDMI VGA output o Supports 4 8 16 CH HD TVI signal 1080P 25 30FPS 720P 25 30 50 60FPS analog signal 960H D1 video input o Supports channel security by hiding live display o Display the local record state and basic information o Supports USB to make full control RECORD MEDIA o Supports one SATA HDD to record for a longer time without any limitation BACKUP o Supports USB 2 0 devices to backup o Supports saving recorded files with AVI standard format to a remote computer through internet RECORD amp PLAYBACK 0 Record modes Manual Schedule and Moti
2. HD TVI DVR User Manual CAUTION e Please read this user manual carefully to ensure that you can use the device correctly and safely e There may be several technically incorrect places or printing errors in this manual The updates will be added into the new version of this manual The contents of this manual are subject to change without notice This device should be operated only from the type of power source indicated on the marking label The voltage of the power must be verified before using If the device doesn t work for a long time pull out the plug from the socket e Do not install this device near any heat sources such as radiators heat registers stoves or other device that produce heat e Do not install this device near water Clean only with a dry cloth Place the device in a well ventilated area Do not power off the DVR at normal recording condition e This machine is indoor using equipment Do not expose the machine in rain or moist environment In case any solid or liquid get into the machine s case please cut off the power supply immediately and ask for qualified technicians to check the machine before restart e Do not try to repair the device by yourself without technical aid or approval When this product is in use the relevant contents of Microsoft Apple and Google will be involved in The pictures and screenshots in this manual are only used to explain the usage of our product The ownerships of
3. 5 4 Search by Image Go to Menu gt Search gt Image tab Select data and channels on the right hand side Press Search button to search for a recorded image 6600 Once an alarm image has been identified the user can double click the image to play recording SEARCH A 3 e CH 01 03 06 2013 09 27 3 4 gt O a x m p _ y A 36 Fig 5 4 Search Configuration Image Lock Select the image and click Lock button to lock this image Save Click Save button to copy the image on the HDD Save All Click Save All button to copy all images on the HDD 5 5 Backup This unit supports backup by USB Flash You can also make backup by IE browser via internet see section 7 3 2 Remote backup Insert USB storage device and then go into backup configuration Refer to Fig 5 5 Set the start amp end time select channels and click Search button to display the searched data in the data backup list box 36 HD TVI DVR User Manual BACKUP Start Time End Time 3121 2013 15 312112013 11 33 21 2013 15 11 13 91 2013 15 12 End Time 03 27 2013 EN 3 21 2013 15 11 40 3121 2013 15 12 23 59 59 Fig 5 5 Backup Configuration Select a required file or checkmark All to select all data files Click Backup button to display Backup information window BACKUP INFORMATION Start Time 03 04 2013 00 00 00 End Time 03 04 2013 23 59 59 The Number Of Fi
4. Click OK Then the unit will power off after a while Disconnect the power 3 2 Login User can login or log off the DVR system Once logged off the user cannot do any other operation except changing the multi screen display User Name admin Password Fig 3 1 Login Notice The default user name is admin and the default password is 123456 For complete operational steps for changing password adding or deleting users please refer to section 4 7 User Management Configuration HD TVI DVR User Manual 3 3 Live Preview Fig 3 2 Live Preview Interface Schedule record 3 4 Live Playback Click Playback button to playback the record Refer to Fig 3 3 User can do complete operation by clicking the buttons on screen 02 77 7017 102450 02 24 2012 20 24 30 p gt A pS Q w Camera Name Fig 3 3 Live Playback HD TVI DVR User Manual 4 Main Menu Setup Guide Click right mouse or press FN ESC button on the front panel and then the control bar will display at the bottom of the screen Refer to Fig 4 1 Screen Mode E zoom PTZ Record Move Main Menu Dwell Audio Snap Playback Fig 4 1 Main Menu Toolbar Screen Mode Click to choose screen mode Dwell Dwell means to display live images from different cameras in a sequence The images may be displayed as a single channel or in a grid fashion from different cameras Dwell mode is enabled only when the chosen display mode is not able
5. button to set the save path Then click Backup button to start backup The backup files will be saved on user s PC 7 6 Remote System Configuration You can do remote setup of the device which includes functions like basic configuration live configuration record configuration schedule configuration alarm configuration network configuration PTZ configuration and user configuration You should select an option from the menu list on the left and then set up the relative parameters Only one user can do configuration setup at a given point of time Click Config tab to go to the below interface The sub menu list and the options in every menu are similar to that of the DVR Please refer to Chapter 4 Main Menu Setup Guide for more details main menu LIVE SEARCH BACKUP CONFIG TOOLS INFO Apply Default b Local View uas S Snap Patt Browse at Liwe Snap Amount D Remote Playback ap Path joune Browse 25 Scned S Amour 1 a iis Local Record LS Save Path Browse ND nem Record Chan it y 4 A o Ow AK 2 4 sub menu opty Detaalt Fig 7 9 Remote Menu Setup 50 HD TVI DVR User Manual 7 7 Tools Click on the tool s tab to access the Disk Management tool The user can view the status of the hard drive s view change the read write properties and format the hard drive s 7 8 Remote Management The Info interface provides a web based interface to access the general inform
6. 1 Motion 03 04 2013 3 04 2013 Motion 03 04 2013 3 04 2013 Motion 03 04 2013 Motion 03 04 2013 03 04 2013 171 Vi Motion Fig 5 2 Search Configuration Event Search Select date and channels on the right hand side A data with highlighted borderline indicates presence of data Checkmark Motion or All accordingly Click Search button to display the searched event information in the event list box OOO 0 Double check a certain record file to playback 5 3 File Management Goto Menu gt Search gt File Management interface Refer to Fig 5 3 SEARCH Time Search Event Search File Management Image Start Time End Time 03 21 2013 15 11 3 21 2013 15 12 04 03 21 2013 15 11 3121 2013 15 12 1 03 21 2013 15 11 4 3 21 2013 15 1 1 03 21 2013 15 11 4 3 21 2013 15 12 00 Lock Fig 5 3 Search Configuration File Management Select date and channels The date with highlighted borderline indicates presence of 35 HD TVI DVR User Manual data Click Search button to display the searched files in the file list box a Use All button to lock unlock or delete all files in the file management column Double click an unlocked item to play Lock Select a file and click Lock button to lock this file after that that file will not be deleted or covered Unlock Select a locked file and click Lock button to unlock this file Delete Select an unlocked file and click Delete button to delete this file
7. Go to Menu gt Setup gt P T Z gt Advanced Refer to Fig 4 32 P T Z Serial Port CH Preset 1 2 3 4 Setting Setting i Setting Setting Cruise Setting Setting Setting Setting Track Setting Setting Setting Setting Default Fig 4 32 P T Z configuration advanced 30 HD TVI DVR User Manual To set up preset In the Advanced interface click preset Setting button to see a dialog box as Fig 4 33 PRESET Channel 1 o Enable Preset Y f Setting f Setting f Setting Setting f Setting f Setting f Setting Setting O E hl WIN lt SIMS TES TES TES TES TES TES TENS Setting OK Fig 4 33 Advanced Preset Setting In the preset setting tab enable preset set the preset name and then click preset Setting button 02 03 04 All Zoom Focus LF Iris Speed 5 Fig 4 34 Preset Setting Control the dome by rotating up up left down right down left left down right and up right and adjust the rotate speed and the value of zoom focus and iris of the dome Select the serial number of the preset point Click button to enable the PTZ wiper and click button to enable the PTZ light Note PTZ must support wiper and light button and these two buttons are just available when selecting PELCOP or PELCOD Click Save button to save the setting Click icon to hide the tool bar Right clic
8. 000 000 000 000 000 000 000 000 000 000 000 Default Fig 4 38 Block Allow List 33 HD TVI DVR User Manual 5 Search Playback amp Backup Search configuration includes four submenus time search event search file management and image 5 1 Time Search Go to Menu gt Search gt Time Search Refer to Fig 5 1 SEARCH ime Search Event Search File Management Image Start Time 0312712013 gD 00 08 alaba Fig 5 1 Search Configuration Time Search Select date and channels on the right hand side and press the Search button A date with highlighted borderline indicates presence of data Set the start time by clicking a particular grid or by entering the specific value in the start time field Select the channel display mode and click Play button to play record Use the playback toolbar to control the playback Pause Play Frame Backward E zoom Cut Hide Move Tool y lt a a E EQ 2 X Camera Name SE TE E gt gt 1X gt To set backup during a certain period in the playback interface Select the start time by dragging the slider and click icon Then select the end time and click this icon again to confirm the record period Next click El icon to backup the record during this period 34 HD TVI DVR User Manual 5 2 Event Search Goto Menu gt Search gt Event Search button Refer to Fig 5 2 SEARCH lime Search Event Search File Management Image CH Type Start Time End Time
9. 2 2 Main Monitor The main monitor settings allow you to set camera sequence in live display mode Operate the following steps to set main monitor Goto Menu gt Setup gt Live gt Main Monitor interface Refer to Fig 4 7 LIYE Liye Main Monitor l Mask Channell v Channel2 v Channel3 v Channel4 v lt Dwell Time S Max Group 2 Current Group 1 l Default Apply Fig 4 7 Live Configuration Main Monitor Select display mode and channel Select dwell time Click KE button to set up the previous channel groups of dwell picture Click d button to set the latter channel groups of dwell picture a Click Apply to save the setting 4 2 3 Mask If there is something you don t want to display in the live image You can set mask For a 13 HD TVI DVR User Manual given channel a maximum of three areas can be masked To set up mask area Goto Menu gt Setup gt Live gt Mask interface LIVE f Live Main Monitor CH Mask Area 1 Setting i Setting 2 3 Setting 4 Setting Default Fig 4 8 Live Configuration Mask Click Setting button to go into live image Press and drag the left mouse button to set mask area as shown below Right click to exit the mask setting interface OOOD Click Apply button to save the setting To delete mask area Click Setting button in the mask interface Select a certain masked area and double click to delete that masked area G Then click A
10. 4 4 Basic Configuration Date amp Time Set the date format time format time zone in this interface checkmark Sync Time With NTP Server to refresh NTP server date You can also adjust system date manually Click Apply button to save the setting 4 1 3 DST Goto Menu gt Setup gt Basic gt DST interface Refer to Fig 4 5 BASIC System Date amp Time Daylight Saving Time Time Offset Hours Mode From Default Fig 4 5 Basic Configuration DST In this interface enable daylight saving time time offset mode start amp end month week date etc Click Apply button to save the setting 4 2 Live Configuration Live configuration includes three submenus live main monitor and mask 4 2 1 Live In this interface you can set up camera name To set up camera name Goto Menu gt Setup gt Live Refer to Fig 4 6 12 HD TVI DVR User Manual LIVE I Main Monitor Mask Camera Name Show Name CAMERAO1 Y CAMERAO2 Y CAMERAO3 Y Y CAMERAO4 Recording Status Y Y Setting f Default Fig 4 6 Live Configuration gt Live A software keyboard will pop up by clicking camera name area Click the letters and or digital numbers on the keyboard to input the name you want to display in live image Checkmark the camera name in the show name area All channels will show the camera name by checking All checkbox Click Apply to save the setting OOO O 4
11. Security Settings General Security Privacy Content Connections Programs Advanced Settings Select a Web content zone to specify its security settings O Internet Local intranet Trusted sites Restricted sites Internet S This zone contains all Web sites you haven t placed in other zones Security level for this zone Custom Custom settings To change the settings click Custom Level To use the recommended settings click Default Level Custom Level Default Level Fig 7 1 Q8 DVR displays please wait all the time a Enable d Download signed ActiveX controls Disable Enable Prompt d Download unsigned Activex controls Disable Prompt 14 Initialize and script Activex controls not marked as safe Disable Enable Prompt A N Abert embed d lira a lt Reset custom settings Reset to Medium Fig 7 2 a HDD power cable and data cable may not be well connected Please check the connections for HDD b Itis also possible that the DVR was forced to stop because HDD has a bad sector and it may have caused the system to halt Check with a good known HDD or try formatting the existing HDD Q9 How to input password and digital numbers Click the password or the input box to pop up a small keyboard Please select characters to be input the initial password is 123436 or you can use the digital keys on the front panel or the digital
12. To add user and set up user authority Goto Menu gt Setup gt Users Refer to Fig 4 28 USER MANAGEMENT User Name User Type PC MAC Address admin Admin 00 00 00 00 00 00 i Setup Delete Change Password Fig 4 28 User Management Configuration Click Add button to display a dialog box as Fig 4 29 ADD USER Authority User Name Password User Type Normal Binding PC MAC Address PC MAC Address 00 00 00 00 00 00 Fig 4 29 Add General 28 HD TVI DVR User Manual In General tab input username password and select user type You can also check Binding PC MAC Address and input this address Click OK to save the setting Note When the default value of binding PC MAC Address is 0 the user is not bound with the specified computer If the bind option is used the user would be able to log into the DVR only through the specific computer carrying the MAC address Select Authority tab and assign the operation rights for particular user Refer to Fig 4 30 Click OK to save the setting ADD USER f P General Log Search System Setup Shut Down vi Two Way Audio File Managemen Disk Manageme Zvi Remote Login vi Live View Y V 1 Zb 7 6 vA vV Manual Record Y Y v 4113 vl vi Playback Fig 4 30 Add User Authority To delete user Go to Menu gt Setup gt Users interface Select the added user you want to delete and then click Delete button To modify
13. circuit 39 6 3 6 4 HD TVI DVR User Manual dielectric material of the disk analysis the potential problems of the disk and warn so as to protect its data Upgrade At present it only supports USB update Get the software from your vendor when there is a new software version The upgrade steps are as follows Copy the upgrade software which gets from vendor into the USB storage device Connect the USB flash drive to the USB port Enter Menu gt T Upgrade tab You will see the upgrade software name displaying in the upgrade list box 0006 Select that software and then click Upgrade button The system will be upgraded automatically Note Please wait for a while when the system reboots Any power interruption is not allowed during upgrading Logoff A log off dialogue box will pop up by clicking Log off icon Then click OK button to confirm to log off If you want to log in again click icon to enter user name and password to re login 40 HD TVI DVR User Manual 7 Remote Surveillance 7 1 IE Remote Surveillance by NAT 7 1 1 NAT Settings The DVR shall be powered on and connected to the network Go to Menu gt Setup D Network You can obtain the IP address Subnet Mask and Gateway automatically You can also manually input them according to the configuration OO of PC And the IP address shall be in the same network segment as the network which is used Set the preferred or alternative DNS Server Please
14. keys on the remote controller HD TVI DVR User Manual Q10 A hard disk is being identified as a new device however it was being used with another DVR of same model Should it be formatted prior use It is possible to migrate an HDD from one DVR to another provided that the DVRs are of the same model and that the HDD being migrated would be used as the sole disk in the new DVR However in cases where the new DVR already contains a HDD the migrated disk being installed would have to be formatted In general migrating disks from one DVR to another is not recommended Q11 What is the minimum configuration required for remote monitoring Direex doo __ Q12 How to handle the situation that the codec Control is blocked when downloading in the VISTA or Win7 system This problem can be fixed in two ways a Enter Control Panel gt User Account and Family Safety gt User Account Control refer to the following figure and click Turn User Account on or off Cancel Use User Account Control UAC to help protect your computer LO X Turn on User Account Control UAC to make your computer more secure User Account Control UAC can help prevent unauthorized changes to your computer We recommend that you leave UAC turned on to help protect your computer F Use User Account Control UAC to help protect your computer a Cancel b Right click IE browser refer to the following figure and select Run as administrator to run
15. name selected by user is a banding domain name of DVR User should logon the website provided by the server supplier to register a user name and password and then apply for a domain name online After the successful application user can access the device from the IE client by inputting that domain name Enable UPnP Select UPnP here and then enable UPnP function in your router Therefore there is no need for you to forward LAN IP address and port in the router in connection of internet After that you can check the WAN IP address in the router gt Domain name Registration Take www dvrdydns com for example 1 Input www dvrdydns com in the IE address bar to visit its website Then click Registration button to register as shown below NEW USER REGISTRATION USER HAME FPASIWOED EELE ka s FIRST NAM xxx LAST HAME My first phone number Submit Resat 2 Create domain name 26 HD TVI DVR User Manual You must create a domain name to continue Domain name must start with a z 0 9 Cannot end or start but may contain a hyphen and is not case sensitive aurdydns com Y 3 After you successfully request your domain name you will see your domain in the list Search by Domain Saarch STATUS DORAN gt DVR Setting Connect DVR to the Network Client 1 Go to Main menu gt Network Other Settings checkmark DDNS select dvrdydns at the DDNS Sever pull down lis
16. refer to 4 6 1 Network for details Go to Menu gt Setup gt Network gt NAT tab Enable NAT and input the NAT Server The default NAT Server is www autonat com Click Apply to save the parameters Please refer to 4 6 5 NAT for details 0050 7 1 2 NAT Access After finishing the NAT settings you can enter the NAT Server on the PC Input http www autonat com to go to the IE client If you are the first time to access the NAT the network will download the ActiveX automatically Note If you cannot download and install ActiveX please refer to FAO OS After installing ActiveX successfully 1t will pop up the login box Serial No 00184E223355 User Name admin Password Language English T LOGIN Serial No The MAC address of the DVR Go to Menu Information Network to check the MAC address of the DVR User Name The login username of DVR The default username is admin Password The login password of DVR The default password is 123456 41 HD TVI DVR User Manual 7 2 TE Remote Surveillance via LAN amp WAN In order to view the DVR from a network it may be connected to a LAN WAN or internet The network setup should be done accordingly Please refer to 4 6 Network Setup This DVR supports IE browser on Windows XP and Vista platform 7 2 1 Via LAN 00 Enter into the DVR s Main Menu gt Setup gt Network interface to input IP address Subnet Mask etc If using DHCP please enable DHCP in both t
17. to set schedule Goto MenuSetup Schedule interface Refer to Fig 4 14 Select channel and click La button to add a certain day schedule Click ill button to delete the selected schedule If you want to apply the schedule setting of a certain channel to other or all channels you need to select channel and click Copy button SCHEDULE Schedule Motion Channel 0 00 00 04 00 08 00 12 00 16 00 20 0 Sunday BAER aa Monday TT TTT TT II TE TT TT TT TT Tuesday AAA A e aH at De De E S Wednesday IP ITT TTT TTT TTT Thursday MAA A A S a D E e Friday 8168 Ga te ie a l c a l a Saturday S PU PA e 11 Apply Settings To Channel f Default Fig 4 14 Schedule Configuration Schedule You can also set week schedule by double clicking in the grinding area This will take you to see a dialog box as Fig 4 15 Select a day and click Add button to set start time and end time Then click to save Select other days and add schedule or copy settings from one schedule to the others under the Apply Settings To item SCHEDULE x Start Time End Time Start Time End Time Y x Fig 4 15 Schedule Week Schedule 18 HD TVI DVR User Manual 4 4 2 Motion Schedule This tab allows to set schedule for motion based recording The setting steps are as follows Go to Menu gt Setup gt Schedule gt Motion tab The setup steps for schedule for motion based recording are similar to no
18. trademarks logos and other intellectual properties related to Microsoft Apple and Google shall belong to the above mentioned companies e This manual is suitable for 4 8 16 channel HD TVI digital video recorders All examples and pictures used in the manual are from 4 channel DVR HD TVI DVR User Manual Table of Contents 1 Introduccion 1 Me WAR LOG OD AAA A Nock tide teh seek ACHAT RR anes 1 12 EA A A A 1 2 Hardware Installali n iii odia 3 Del ostal Hard DAVE A A A E a TEA 3 22 Front Panel DESCOPION sr 5205440500 RA A AAE Ae 4 De Ire al Panel MIS UBC ONS liada 4 LA REMO Conto OT os sx ci A A E CA DEDE da 5 ZIC ONTO With VOU SC aie E 6 2 3751 A VIOUS aira a a CRA aariees cas Ae bh aa 6 p 220 3974 A O 6 3 Basic Function Instruction na 8 34V POW ONOI cysts cua 0022 a 2A PO OA MA R A A cam E RA Ae iA C dA Den n 8 FV A OO 8 A AE en 8 A A OR AN 8 NS A A SA AEN d N Cac ESRA a 9 DA AV GP lay DAC PR AA jO cee 9 4 Main Menu Setup Guide cccccccccccccccocoooccccocccccccc0c00000000000000000000000000000000000000000000000000000 10 44 Basic CONIL AANA 10 Abe ALS SUCHIN E EA A EA FE EA FE AS 11 EP IO OC B MAA AA EROE EENET 11 A O A 00622 CAE 12 ERE 2 2212227000 22 AA 0222 AE E EE EEE 2 AMPE EA 24977 12 4 2 Live Con Uro nta diia 12 A Dee LV E da se voc e g An A D E D EU CNL CON D UV AE COAL 12 4 22 Main NOOO aiii 13 42 53 MAS Gane eta eR A A Pe a a 13 4 3 Record CONSUMO A AA A AA A A A 14 O E 15 4 32 Record Bitar 15 A3 P TI
19. user Goto Menu Setup gt Users interface Select the added user you want to modify and then click Modify button to do the relevant operation To change user password Goto Menu gt Setup gt Users interface Select the added user you want to change its password and then click Change Password button 4 8 P T Z Configuration P T Z configuration includes two submenus serial port and advanced Serial port settings are as follows 29 HD TVI DVR User Manual Goto Menu gt Setup gt P T Z Serial Port interface Refer to Fig 4 31 A Enabl Address Y Y Y Y 2 4 b d wY v 9600 Y 9600 Y 9600 Y 9600 v 9600 Y Protocol Simulative Cruise Pell ad PELGOP ad PELEOP Og PELO ag PELLS P Va Baud rate of the PTZ device Range form 110 300 600 1200 2400 4800 9600 19200 34800 57600 115200 230400 460800 921600 Communication protocol of the PTZ device Range from NULL Protocol PELCOP PELCOD LILIN MINKING NEON STAR VIDO DSCP VISCA SAMSUNG RM110 HY N control Simulative If enabled no matter whether the PTZ device supports cruise or not the Cruise presets will cruise Select Enable and set up the value of address baud rate and protocol according to the Baud rate settings of the speed dome Select All to set the same settings for all channels Advanced settings include preset setting cruise setting and track setting
20. 0 Motion 2012 02 28 13 30 14 2012 02 28 13 31 09 Motion 2012 02 28 13 28 45 2012 02 28 13 30 13 Motion 2012 02 28 13 26 46 2012 02 28 13 28 21 Motion 2012 02 28 13 24 26 2012 02 28 13 25 44 Motion 2012 02 28 13 13 24 2012 02 28 13 14 37 Motion 2012 02 28 12 54 14 2012 02 28 12 55 38 Motion 2012 02 28 12 47 21 2012 02 28 12 49 05 Motion 2012 02 28 12 46 21 2012 02 28 12 47 21 Motion 2012 02 28 12 45 26 2012 02 28 12 46 21 Motion NININ IN NN NN ININ IN IN Na 2012 02 28 12 43 49 2012 02 28 12 45 26 Motion File Management re JE Lo Jeu Fig 7 6 Event Search Interface Sun Mon Tue Wed Thu 1 ae IDO 8 12 13 14 19 20 21 26 27 MM 29 Channel 2 9 15 16 22 23 Mi M2 M3 Motion O Al Goto Search gt File Management interface Refer to Fig 7 7 Channel Start Time End Time 2 2012 02 28 13 42 18 2012 02 28 13 42 25 2012 02 28 12 47 21 2012 02 28 13 42 18 2012 02 28 12 18 00 2012 02 28 12 47 21 2012 02 28 11 49 53 2012 02 28 12 18 00 2012 02 28 11 22 41 2012 02 28 11 49 53 2012 02 28 10 56 53 2012 02 28 11 22 41 2012 02 28 10 30 04 2012 02 28 10 56 53 2012 02 28 10 02 59 2012 02 28 10 30 04 2012 02 28 09 34 12 2012 02 28 10 02 59 2012 02 28 09 09 43 2012 02 28 09 34 12 2012 02 28 13 34 49 2012 02 28
21. 13 42 25 2012 02 28 13 23 25 2012 02 28 13 34 49 004 0 0 10 0 0 0 0 0 0 0 WIWIWININININININ INI N N 2012 02 28 13 11 57 2012 02 28 13 23 25 AR 123 att fat Labu P Lock J __Uniock Delete Fri Sat 3 4 10 11 17 18 24 25 Ma Sun Mon Tue Wed Thu Fri Sat 1 6 7 8 26 27 MM 29 Channel EJER M2 M3 M4 Fig 7 7 File Management Interface 2 Select highlighted date and channels Click Search button to search the recorded files Lock Select certain file item in the file list box and then click Lock button to lock this file that ca not be deleted or overlaid Unlock Select a locked file and then click Unlock button to unlock this file 49 2 3 4 9 18 Il 12 13 14 15 16 17 18 19 20 21 22 23 24 25 HD TVI DVR User Manual Delete Select an unlock file and then click Delete button to delete this file from file list 7 5 2 Remote Backup Click Backup button to go to backup interface Please refer to Fig 7 8 2 02 28 08 41 06 2012 02 28 08 44 21 2012 02 28 08 44 49 Lie llo pi Search Start Time 2012 02 28 00 00 00 End Time 2012 02 28 3 59 59 Besos Beciup Fig 7 8 Remote Backup Interface Select channels set the start and end time and then click Search button to display the file information in the file list box Select backup files and click Browse
22. A OS 38 0 14 NEIWOrK tO MAI Dti AAA t 38 OS Online IO A AES 2A NASA 0 R0 20200 NATA ESAN AUDA 38 LORO Moi 38 ASEO RCODES ds AAA AAA AA A dees 38 0 2 Disk Mande MEN laica 39 BBP A A ECE 2424229 A NOE leew 20 E sata E E05 9A 00020 ENE EEE EAC 40 A Ae AS Ae Ae eA Ae eet a 40 T Remote SUELA A AA A AA Sale 41 T1 1 1E Remotesutrvenlatico DY NA Dat id 41 ISLA SOS en co tortitas dm pe 41 TZ NAT RC COS taa 41 7 2 IE Remote Surveillance via LAN amp WAN vivian ninia iii ide 42 CZ Vale AAA II II EASE AAS EAA 42 NP O 42 T 3 Remote Surveillance through Apple Plisadas ad lidia das 43 IS MALENA A E as 43 LN TA WAN AAA ta 44 dt The Remote live Prev Wai e 45 TS Remote Playback amp Bac A A risa 47 HD TVI DVR User Manual TI Remote Playback 4225025369555495 oa 47 75 2 Remote ls AAA A Dent Deen s vada ca Nere Na dO eL 50 7 6 Remote System Contfis ur ati01z socas cess ev A A A E ia 50 Tah NOON E e E E EA E E AE 2 E saa aula daa teins ads A EA AE 20 107077 200 51 TS Remote Manas CMe it e a ci 51 POTN A FAO A AA Re A As 52 Appendix B Calculate Recording Capacity ccccccccoooo000ooooooo0000000000000000000000000000000000000 56 Appendix C Compatible Devices 00000000000000000000000000000000000000000000000000000000000000000000000000 57 Appendix D 4 CH Specifications wisssssescccsvessxecsssesssessecaseasusaccecssseevecssheoeseacoanvacsesasnseaveanneeees 58 Appendix E S CH Specific OO Sai As 59 Appendix F 16 CH Specifications
23. E ce ree RRA 16 ze cd Ms 12 9 D e pe a ene nr 2 090 ry OE nC Prey AAEN Sonny A ARO nC rT 200000 15022 02051 A ARE nny SOE OE 16 Ay De D O A e PA 1 CON Roan tuchiar ee CATA Lhi 17 ATES HO Fes 12 O TA S O Ae Oem 17 44 Schedule COMM UA cios 18 A E AN SEA uk eins we aly deh 0 0 E 011 24 14 7 en EN EA 18 4 42 MONOS CCC UNG na is Soret es end AN ar arti cll ops ie Reed la A 19 FATE Ce OM pF CURA O E ad coa 19 SA O A bN ONN RR 19 25 2 NTIEO DOS eaa aa A A Ao dA ALP AA I AE N D A IRA AE ihn 21 AN O 1 6 Aa i n 21 HD TVI DVR User Manual 4 5 4 A E A SA ESTAR AN ERSO 22 A O Netwotk COnimourall On nilo pi dt idad 22 SOV NE WO Aa 22 EP OZ UNO 1810 A Pu A o Ii MEE aara MSA VANT 23 AOS EM dni 24 E SI II E 111090 19 202 dad 1024 R 21000 111000 NER EA 0 4 1906 24 LOS NA Tene A nla se Soak ts soe LE A AT CAS 25 Ab Os CUS SE Mne isla ti it tit 25 47 User Manas ement Conti UTA ri 28 AE CORA SUPA OM E E as 29 INN E ea A E11 E PEE R E R ECE 33 A DIRES C roe A T XA AAA CAA OA AAA ce donee AA ACT seeders 33 AN OA TAPO UE O 2 ERA ARI AD E te AA O ed Cte Meee P D 33 49 35 OC AON EIS IPAPER N os etn en re205 Aa aed EAE 33 5 search Play back amp Backup diia cananea rinda 34 A II A E he anand es 34 5 2 EVEI SCO AAA A A 35 le Mana men tdt aa 35 O NS A II A Sdn Loot 36 ODIA EAS 36 6 Manage DVRS 38 Gal Check SISTE IO TA att OO rr AAA AAA 38 IES AAA e C M aera E A E M 38 O TZ AA A a da OL ANA LAA 48 22 d CA S VAA TAA 320 38 6 13 Los Intotmation
24. PAL 4096 1800 30 NTSC 3072 1350 2048 1024 2700 2025 12 PAL 1575 15 NTSC 1350 The calculation format is Total Recording capacity Used space per hour MB h coverage rate of hard disk x recording time hour x channel numbers For instance one customer uses NTSC cameras set resolution to 720P video quality to Lowest frame rate to 30 fps for enabling total 4 channels He wants the unit to record continuously in a month Below is the calculation Total Recoding capacity 450 mb h X 24 hours day X30 days X4 channels 1296000 MB 1266 GB Therefore you need to install one 2 TB SATA HDD for recording in one month 56 HD TVI DVR User Manual Appendix C Compatible Devices 1 Compatible USB drive after test Capacity SSK 512MB 1G 2GB Kingston 2 Compatible HDD list 1606 HITACHI Deskstar 80G 160G Western Digital 160G 250G 320G 1 5T 2TB 3TB Samsung HDI161HJ 160G 57 HD TVI DVR User Manual Appendix D 4 CH Specifications H 264 High Profile VGA x 1 HDM Ix 1 4CH 1080P 25 30FPS 720P 20 30 50 60FPS 960H D1 video input 1080 x 1920 1280 x1024 800 x 600 1080P 1920 x 1080 720P 1280 x 720 960H D1 100FPS PAL 120FPS NTSC 720P 960H D1 100FPS PAL 120FPS NTSC 1080P SOFPS PAL 60FPS NTSC RCA x 1 RCA x 1 Manual Timer Motion detection Pentaplex RJ45 LAN INTERNET YES RS485 USB2 0 x 2 one for backup another for USB mouse SATA x 1 E lt 9W w
25. amp Position Y Setting Setting 1 2 Y 3 Y Setting 4 Y Setting Setting Default Fig 4 13 Record Configuration Stamp Checkmark camera name and time stamp Click Setting button to set up the position of the stamp You can drag the camera name and time stamp at random positions Refer to below Figures 07 24 2019 7 4 pif 4 y Before drag After drag Select All to set up all channels with the same parameters 4 3 5 Recycle Record This option is used to recycle the HDD space once it is full If enabled the system will automatically delete the old records and recycle the space if it is completely utilized The setting steps are as follows Go to Menu gt Setup gt Record gt Recycle Record interface 2 Checkmark recycle record to activate auto recycling If the option is disabled or not selected the DVR would stop recording once HDD is full G Click Apply button to save the setting 4 3 6 Snap In this interface user can set up Resolution quality snap interval snap number 17 HD TVI DVR User Manual 4 4 Schedule Configuration Schedule configuration includes two sub menus schedule and motion 4 4 1 Schedule This tab allows defining schedule for normal recording for seven days of a week 24 hours of a day Every row denotes an hourly timeline for a day Click the grid to do relevant setup A highlighted area denotes selected timeline Operate the following steps
26. ation pertaining to the DVR s settings The interface includes five submenus System Event Log Network and Online users Note There may be subtle differences with respect to functions of remote surveillance between through IE and through Apple PC Here we only take IE remote access for example 51 HD TVI DVR User Manual AppendixA FAQ Q1 a b Q2 Q3 Q4 Q6 Why the DVR doesn t turn on after connecting to the power The power adapter could have gone bad Please change a new power adapter The power from the adapter may be not enough for operating the DVR Please use the power adaptor supplied along with the DVR It could be a hardware problem The DVR LED turns on but there is no output why The power from the adapter may be not enough for operating the DVR Please use the power adaptor supplied along with the DVR It could be a wiring issue Please check the connection for the same Check the monitor settings Why are no images displayed on few or all channels of the DVR It could be a wiring issue Please check the cable and the ports of the cameras and DVR The problem can also be related to cameras Please check the same Please make sure that the channels are not programmed as hidden channels and check the status from admin login The HDD cannot be found The power from the adapter may be not enough for operating the DVR Please use the power adaptor supplied along with the DVR It could
27. ay on the client end or CMS that help user to recognize the device remotely Device ID This ID is used to map the speed dome cameras Video Format Two modes PAL and NTSC User can select the video format according to that of camera Password Check If this option is enabled the user would need to input the user name and the password for performing corresponding operations Show System Time If selected the current time will be displayed during live monitoring Max Online Users To set the max number of concurrent user logins in the DVR Video Output The resolution of live display interface Language Set up the menu language Note After changing the language and video output the device needs to login again Logout After Minutes A user can set up the screen interval time 30s 60s 180s 300s If there is no any operation within the setting period the device will auto logout and return to login interface Show Wizard If selected the GUI would launch the startup wizard on every boot allowing the user to do basic setup No Image When Logout If selected there will be no image showing when logging out 4 1 2 Time amp Date Goto Menu gt Setup gt Basic gt Date amp Time interface Refer to Fig 4 4 11 HD TVI DVR User Manual BASIC System Date Format Time Format Time Zone Sync Time With NTP Serer NTP Server time windows com System Date OR MOS APL 25 System Time US 8 32 3 20 f Default Fig
28. be wiring issue Please check the power and data cables of the HDD The HDD could have gone bad Change a new one The DVR cannot record Make sure the HDD was formatted prior to use Maybe the user hasn t enabled the record function or has done incorrect setup Please refer to Chapter 5 Maybe HDD is full and thus the DVR is not able to record Check HDD information from Disk Management and if required please enable the recycle function The HDD could have gone bad Please change another one Mouse doesn t work a The mouse should be connected to the USB port at the rear side b After connecting the mouse allow the DVR to detect the mouse for seconds If not detected try restarting the DVR c The mouse may be incompatible Please change a mouse Q7 ActiveX control cannot be downloaded 52 HD TVI DVR User Manual a IE browser blocks ActiveX Please do setup as per the steps mentioned below Open IE browser Click Tools gt Internet Options 3 about blank Microsoft Internet Explorer File Edit View Favorites Help Mail and News b Synchronize Windows Update Show Related Links Internet Options Select Security gt Custom Level Refer to Fig 7 1 Enable all the sub options under ActiveX controls and plug ins Refer to Fig 7 2 Then click Ok to finish setup 00 b Other plug ins or anti virus blocks ActiveX Please uninstall or do the required settings Internet Options x
29. bit rate Range from 256 1792kbps Select fps resolution quality encode and max bit rate Select All to set the same settings for all channels 4 6 3 Email To set up Email Goto Menu gt Setup gt Network gt Email interface Refer to Fig 4 24 NETWORK Network Sub stream Server NAT Other Settings SMTP Server Port SSL Check Send Address Password Receive Address1 Receive Address2 Receive Address3 Test f Default Fig 4 24 Network Configuration Email Set SMTP Server and port SMTP Server Port The name and port number of SMTP server You can set up SSL check such as Gmail according to actual needs Set sender s address and password 4 Set receiver s email address and click Test button to test the validity of the mailbox Attaching image If selected the system will attach images when sending emails 4 6 4 Server This function is mainly used for connecting ECMS NVMS The setting steps are as follows In the server interface select Enable as shown in the Fig 4 25 Check the IP address and port of the transfer media server in the ECMS NVMS The default server port for auto report is 2009 If it is modified please go into the transfer media interface to check 24 HD TVI DVR User Manual NETWORK Network Sub stream Email Server NAT Other Settings Enable Server 192 168 3 123 Server Port 10002 Device ID 382 f Default Fig 4 25 Netw
30. bols input Click Shift button to input Capital letters and symbols click Shift button again to return It supports mouse drag Take setting up motion detection area for example Click customized hold down the left button and drag to set motion detection area HD TVI DVR User Manual Click to choose the options Right click to return to live mode In Backup Click to choose the options Right click to return to previous picture In PTZ Control Click left button to choose the buttons to control the PTZ Click right button to return to live Note Mouse is the default tool for all operations unless an exception as indicated HD TVI DVR User Manual 3 Basic Function Instruction 3 1 Power On Off Before you power on the unit please make sure all the connection is good 3 1 1 Power On Connect with the power 2 The device will boot and the power LED would turn blue G3 A WIZZARD window will pop up and show some information about time zone time setup network configuration record configuration and disk management User can set up here and refer to the concrete setup steps from the corresponding chapters If users don t want to set up Wizard please click Exit button to exit Press and hold FN ESC key to switch the resolution of the VGA HDMI output 3 1 2 Power Off You can power off the device by using remote controller keyboard and mouse D Goto Menu and then select Shut Down icon to pop up the Shut down window
31. browser 54 HD TVI DVR User Manual Open Open file location Run as administrator Restore previous versions Send To b Cut Copy Create Shortcut Delete Rename Properties Q13 How to play the backup file Insert your USB device where the backup files are saved in the USB port of PC If your files are saved in DVR format you must have already downloaded the backup player box before doing backup Then double click to open your USB disk to find your backup files and backup 4203 SuperPlay player Double click K icon to install backup player After you install it open this player and click Open Path button to open your backup file Next click play button to play the backup file Double click the image and then right click to enable audio If you save your backup files in AVI format you can directly open your file by using the media player which supports this format 009 0 6 F AAA a GAMA JAM RR AME id UM DA OA SAA A T TAL AA OMA AS AMAR AC AA SR RRM a M Gas hs Ip in ar Ga 1201 20324155704 AS 55 HD TVI DVR User Manual Appendix B Calculate Recording Capacity Users can calculate the size of hard disk according to the saving time and DVR recording settings The DVR uses fixed video bit rate The below are the details at different settings Resolut Frame Rate A Bit Rate Used Video Quality ion Totally FPS kbps Space MB h 6144 2700 Higher 5420 2250 25
32. creen Email Fig 4 17 Alarm Configuration Motion Trigger Buzzer If selected the local buzzer would be activated on an alarm Show Full Screen If selected there will pop up the chosen channel on the monitor on an alarm trigger Email If selected the DVR will send an email alert to the preconfigured email address in case of a motion based alarm from the particular input Snap If selected the system will snap images of the checked channels on an alarm and save them in the HDD automatically o Go to To Record tab Select recording channels It would be recorded in case of an alarm Click OK button to save the setting After clicking Area button a dialog box will pop up as Fig 4 18 In the Area interface you can drag slide bar to set the sensitivity value 1 8 The higher the value is the more sensitive it is to motion Since the sensitivity is influenced by color and time day or night you can adjust its value according to the practical conditions Left click the grid and drag to delete area Click icon to set the whole area as detection area Click icon to clear the set detection area Click A icon to test the sensitivity as per the local conditions Once motion is sensed it displays a figure icon Click MEM icon to save the setting Click icon to exit the current interface Fig 4 18 Motion Area 20 HD TVI DVR User Manual Note Prior to setting motion detection field it is recommended that you click c
33. er ge Cec Bop orme uucaxecor WEEER GR Select Open in 32 bit mode 7 3 1 Via LAN a After starting Apple computer click Apple icon The following window will pop up Please select System Preferences gt Internet amp Wireless gt Network Go into Network interface and then click Ethernet Connected to check the internet connection of Apple PC 43 HD TVI DVR User Manual Status Connected Ethernet is currently active and has the IP About This Mac address XXX XXX 1000 XXX Software Update Configure IPv4 Manually Mac O5 X Software IP Address XXX XXX XXX XXX Dock Subnet Mask XXX XXX XXX XXX Recent Items gt Router XXX XXX XXX XXX Force Quit Finder PHD ee ca Sleep Ke Search Domains Restart Advanced 7 Shut Down Log Out coodoo 0x0 her changes Assist me G After acquiring the IP address Subnet Mask and so on please Go to the DVR s Main Menu gt Setup gt Network interface to manually input IP address Subnet Mask and Gateway according to the configuration of PC The network segment should be the same as the PC If using DHCP please enable DHCP in the DVR and router After the above information is completed you can enter LAN IP and http port in the Safari browser For example input http 192 168 1 100 81 here 192 168 1 100 is LAN IP of DVR 81 is the http port of DVR and click button Then the browser will download Active X contr
34. for every channel it requires low network bandwidth Therefore you can select the stream according to your bandwidth All to master sub stream Set all channel to master stream or sub stream Enable audio Enable or disenable audio Full screen The live preview picture will display with full screen and the tool bar will be hid Double click left mouse or click right mouse to return Zoom in Single channel large screen electronic amplification Click the channel which needs to be zoomed Right click to select zoom in button to zoom in the image Double click or right click to exit 7 5 Remote Playback amp Backup 7 5 1 Remote Playback Click 13 button to go into record playback interface Refer to Fig 7 3 Select the record date and channels and double click the file name in the record file list box Then you can play that file and preview the picture a Record Date 20091224 dl 4 00 00 00 00 00 00 CAMI cAn cam 7 CAMA File Name Fe Lenc 20091224001802_01 avi 00 18 02 20091224063015_03 avi 06 30 15 20091224062529 04 avi 06 25 29 2 3 20091224062750_02 avi 06 27 50 AA 2009 02 09 15151 40 20031224062529 O9 avi 06 25 29 fast forward previous file full screen play pause stop next frame next file path volume Fig 7 3 Play Record File Interface 47 HD TVI DVR User Manual This DVR supports remote time search event search and file management By Time Search Go to Searc
35. ghest VBR and CBR Max bit stream You shall adjust it subject to the actual network condition 4 3 3 Time Goto Menu gt Setup gt Record gt Time interface to set recording time Refer to Fig 4 12 RECORD Enable Record Bitrate Stamp Recycle Record Snap CH Pre alarm Record Tim Post alarm Record Tim Expire Days Never Yv Never w Jf Go S io w Never Ww v Never oO aia A 19 4 4 4 4 4 Default Fig 4 12 Record Configuration Time Set Pre alarm record time and post alarm record time Select All to set the same settings for all channels Pre alarm Record Time Set the time in seconds to pre record before the actual recording begins Post alarm Record Time Set the time in seconds to post record after the actual recording has finished five options 10s 15s 20s 30s 60s 120s 180s and 300s Expire Time Set the expiration time for recorded video If the set date is overdue the recorded files will be deleted automatically Click Apply to save the setting 4 3 4 Stamp This provides an option to enable or disable the Camera Name and the Time stamp on the video The user can also choose a position for the stamp on the screen To set up stamp as follows Goto Menu gt Setup gt Record gt Stamp interface Refer to Fig 4 13 16 HD TVI DVR User Manual RECORD Enable Record Bitrate Time Recycle Record Snap CH Camera Name Time St
36. h gt Time Search Refer to Fig 7 4 The highlight date in the area indicates recorded data Select the date in area and record channels in area 8 Click Search button The record data will be displayed in the data information list box Set the data playing time and display mode in the area as required CSG OO Click Play button to playback 8 CH DVR only supports single channel display 2013 02 24 oo 00 00 Chann Fig 7 4 Time Search Interface Click the relevant buttons in the interface for operation like FF pause change channel mode etc Refer to Fig 7 5 l ave SEARCH BACKUP CONFIG q 2013 02 24 13 oo 00 00 as tocaran HA rre el Us gt i DS 42 C2024 20 200 Previous Play Backward Stop Section Full Screen Sasy Fig 7 5 Time Search Playback 48 By Event Search OSGOO0 Channel HD TVI DVR User Manual Checkmark the event type motion Click Search button Double click certain item to play Go to Search gt Event Search interface Refer to Fig 7 6 Click the highlight date and select record channels Start Time End Time Type 2 2012 02 28 13 37 25 2012 02 28 13 38 50 Motion 2012 02 28 13 34 57 2012 02 28 13 36 52 Motion 2012 02 28 13 33 44 2012 02 28 13 34 56 Motion 2012 02 28 13 32 21 2012 02 28 13 33 44 Motion 2012 02 28 13 31 10 2012 02 28 13 32 2
37. he DVR and the router Enter Record Setup to set network video parameters like resolution frame rate etc Open IE on a computer on the same network Input the IP address of the DVR in IE address bar and press enter IE will download ActiveX component automatically Enter the username and password in the subsequent window Notice If HTTP port is not 80 other number instead add the port number after IP address For example set HTTP port as 82 input IP address like 192 168 0 25 82 User name and password here are the same with that used on the DVR The default username is admin and the default password is 123456 7 2 2 Via WAN There are two ways for the DVR to connect to internet 1 Connect the DVR to internet through router or virtual server 2 Enter into the DVR s Main Menu gt Setup gt Network interface to input IP address Subnet Mask etc If using DHCP please enable DHCP in both the DVR and router Forward IP address and port number in Virtual Server setup of the router or virtual server Configure the firewall to allow accessing the DVR If the user has enabled the UPnP function in both the DVR and router he can skip this step If users want to utilize dynamic domain name please apply for a domain name in a DNS server supported by the DVR or router Then add to the DVR or router Open IE browser input IP address or dynamic domain name and enter If HTTP port is not 80 add the port number after IP addres
38. ick this button again to stop playing Click E icon to exit the current interface OF 00 32 4 9 Advanced Advanced configuration includes three submenus reset import export and Block Allow list 4 9 1 Reset HD TVI DVR User Manual 02 03 04 All Track Start Record Start Track Fig 4 37 Track Setting Reset all settings of the device 4 9 2 Import Export Export the data files into mobile storage devices for backup and then import specified data files from mobile storage device to DVR 4 9 3 Block Allow List BLOCK FP ALLOW LIST D To L 3 4 5 6 7 8 9 Here authorized user can prohibit computer users within a certain IP address range from accessing to DVR or allow computer users within a certain IP address range to access DVR E g if an admin user doesn t want computer users within IP address range from 192 168 000 002 to 192 168 000 004 to access the DVR he can check Block list option and then input such IP address range If it is required that computer users within a certain IP address range access DVR they can check Allow List option and then do the required setting O Block List IP From 192 168 000 002 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 Allow List 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000
39. icon to clear the existing field and set afresh Select All to set the same settings for all channels Click Apply button to save the setting G Q Go to Schedule tab The setting steps for schedule for motion based alarm are similar to normal schedule setup see Chapter 4 4 1 for more details 4 5 2 Video Loss This DVR can be set up to detect video loss The setting steps are as follows Go to Menu gt Setup gt Alarm gt Video Loss Refer to Fig 4 19 The setup steps of video loss trigger are similar to motion trigger setting See Chapter 4 5 1 Motion gt Trigger setting for more details VIDEO LOSS Trigger Trigger Trigger Trigger Default Fig 4 19 Alarm Configuration Video Loss 4 5 3 Other Alarm This tab gives a choice to configure alarm for Disk Full IP Conflict the Disconnect event Disk Attenuation or Disk Lost Goto Menu gt Setup gt Other Alarm Refer to Fig 4 20 OTHER ALARM Alarm Type Disk Full Y Dis K Full Buzzer IP Conflict z Disconnect Email Disk Attenuation Disk Shortage Alarm Dale Last i Default Fig 4 20 Other Alarm 21 HD TVI DVR User Manual QG S Use the dropdown menu and select the event or the alarm Check the required trigger options If the selected event is Disk Full then use the drop down box for Disk Shortage Alarm to choose a threshold value for remaining HDD space If the threshold value is reached the system wi
40. ithout HDD DC12V 0 C 50 C 10 90 V 58 HD TVI DVR User Manual Appendix E 8 CH Specifications H 264 High Profile VGA x 1 HDM Ix 1 8CH 1080P 25 30FPS 720P 20 30 50 60FPS 960H D1 video input 1080 x 1920 1280 xX 024 800 x 600 1080P 1920 x 1080 720P 1280 x 720 960H D1 200FPS PAL 240FPS NTSC 720P 960H D1 200FPS PAL 240FPS NTSC 1080P 100FPS PAL 120FPS NTSC RCA x 1 RCA x 1 Manual Timer Motion detection Pentaplex RJ45 LAN INTERNET YES RS485 USB2 0 x 2 one for backup another for USB mouse SATA x 1 E lt 14W without HDD DC12V 0 C 50 C 10 90 Nn 59 HD TVI DVR User Manual Appendix F 16 CH Specifications H 264 High Profile VGA x 1 HDM Ix 1 16CH 1080P 25 30FPS 720P 20 30 50 60FPS 960H D1 video input 1080 x 1920 1280 x 024 800 x 600 1080P 1920 x 1080 720P 1280 x 720 960H D1 AOOFPS PAL 480FPS NTSC 720P 960H D1 400FPS PAL 480FPS NTSC 1080P 200FPS PAL 240FPS NTSC RCA x 1 RCA x 1 Manual Timer Motion detection Pentaplex RJ45 LAN INTERNET YES RS485 USB2 0 x 2 one for backup another for USB mouse SATA x 1 E lt 20W without HDD DC12V 0 C 50 C 10 90 Nn 60 A2
41. k to view this bar again Click icon to exit the current interface Return to the Advanced Preset Setting interface and click OK button to save the setting To set up cruise Inthe Advanced interface click cruise Setting button to see a window as shown in Fig 4 35 31 HD TVI DVR User Manual CRUISE Channel 1 No Name 1 Cruise 2 Cruise Setup Delete Clear All Fig 4 35 Cruise Setting Click Add button to add cruise line in the list box 8 cruise lines can be added at most G Select a cruise line and click Setup button to see a dialog box as Fig 4 36 precleared R Fig 4 36 Modifying Cruise Line a Click Add icon to set the speed and time of preset point Select a a gt aR and to then click Delete icon KA to delete that preset point Click Modify icon FERR those icons to adjust the position of preset point Click Preview button to preview the cruise line Click OK button to save the setting modify the setting of a preset point User can click To set up track In the Advanced interface click track Setting button to see a dialog box as Fig 4 37 Control the dome by rotating up up left down right down left left down right and up right and adjust the rotate speed and the value of zoom focus and iris of the dome Click Start Record button to record the move track of PTZ Click this button again to stop record Click Start track button to play recorded track Cl
42. les Size GB Storage Media Free GB Backup Player Save File Type Disk Cleanup roa 4 In the backup information interface you can check the relevant information of backup files storage type save file type etc Then click Start button to start backup Note If the backup files are saved in DVR format please check backup player Only this player can play these files in DVR format If the backup files are saved in AVI format you can play these files with common media player 37 HD TVI DVR User Manual 6 Manage DVR 6 1 Check System Information Check system information includes six submenus system event log network online user and record 6 1 1 System Information In this interface you can check the hardware version MCU version kernel version device ID etc 6 1 2 Event Information In this interface you can search for events like motion and video loss The utility provides an interface to have a date based and a channel based search This report can further be saved on a USB flash drive as an html file using the export button 6 1 3 Log Information In this interface you can search for relevant logs as per set date and event which includes Operation Setup Playback Backup Search Check Information and Error This report can further be saved on a USB flash drive as an html file using the export button 6 1 4 Network Information In this interface you can check relevant parameters of network 6 1 5 On
43. line Information In this interface you can check the details of the connected online users Refresh Refresh the current interface Disconnect Disconnect the online users to access DVR If this function is used by the admin the particular PC will not be able to access the device for five minutes 6 1 6 Record Information In this interface a user can check resolution ftp and record status including motion recording manual recording or schedule recording 6 1 7 QRCODE User can quickly access the mobile client by scanning QRCODE Go to Main menu gt Information gt QRCODE tab Refer to Fig 6 1 38 HD TVI DVR User Manual INFORMATION ra J Network gt e FA O em Online Users Record QRCODE Fig 6 1 Information Configuration In this interface you can scan the QRCODE through the mobile phone Refer to Fig 6 2 QRCode Fig 6 2 Information Configuration QRCODE 6 2 Disk Management To format the disk D Go to disk management interface Note please format the hard disk before record 2 Click Refresh button to refresh the disk information in the list box 3 Select a hard disk and click Format button to start format Note All recorded files in the hard disk will be lost after formatting To check other information of disk After you Go to Disk Management Advanced tab you can check model S N firmware health status of the disk in this interface You also can monitor the temperature internal
44. ll trigger the Disk Full Alarm Click Apply to save the setting 4 5 4 Alarm Out To set up alarm out Go to Menu gt Setup gt Alarm Out Refer to Fig 4 21 ALARM OUT Buzzer Buzzer Hold Time S Default Apply Fig 4 21 Alarm Out Checkmark Buzzer and set buzzer alarm hold time This would trigger the buzzer when the system is on an alarm 4 6 Network Configuration Network configuration includes six submenus Network Sub Stream Email Server NAT and Other Settings Network settings must be configured if DVR is used for monitoring over network 4 6 1 Network To set up network o Go to Menu gt Setup gt Network Network tab Refer to Fig 4 22 Set HTTP port The default HTTP port is 80 If the value is changed you shall add the port number when typing IP address in IE address blank e g If HTTP port is set to 82 and IP address is http 192 168 0 25 you should input the following IP address http 192 168 0 25 82 into IE browser Set server port The default server port is 6036 22 HD TVI DVR User Manual NETWORK Network Sub stream Email Server NAT Other Settings IP Address Subnet Mask Gateway Preferred DNS Server Alternate DNS Serer 000 000 000 000 PPPoE User Name Password Test Default Fig 4 22 Network Configuration Network 4 Connect internet There are three ways to connect internet gt Ifyou have a DHCP server running and wo
45. n speed Iris and zoom focus on the dome and set the presets etc Buttons definition Ato rotate the dome upwards Y to rotate the dome diagonally up left to rotate the dome diagonally up right W to rotate the dome downwards to rotate the dome diagonally down right to rotate the dome diagonally down left to rotate the dome towards left B to rotate the dome towards right BM to stop rotating the dome Iris button Click button near Tris button to increase light of the dome Click button near Iris button to decrease light of the dome Zoom button Click button near Zoom button to zoom in the locale picture of this camera Click button near Zoom button to zoom out the locale picture of this camera Focus button Click button near Focus button to have long focus Click a button near Focus button to have short focus Go to the Preset a o Select and do auto cruise A 2 E Click the right mouse on the live interface This will take you to a pull down menu 46 HD TVI DVR User Manual Master Stream Sub stream All to Master Stream All to Sub stream Enable Audio Full Screen zoom in Fig 7 2 Right Key Sub Menu Stream This DVR supports master stream and sub stream Master stream has higher frame rate max 25FPS PAL 30 FPS NTSC for every channel but it needs higher network bandwidth simultaneously Sub stream has low frame rate max 6FPS PAL 7FPS NTSC
46. ol as shown below ann Web Chen 4 MOM im 192 168 L 100281 c Ha es 10 Ansie wmtzthwtd dealer please click icon to load and install WebkitPiugin please restart browser to ensure WebkitPlugin can take effect after install 6 Click icon and then select the Active X control the welcome interface will be shown Click Continue Install button the following window will pop up ane Install WebClientPlugin 64 AAN arcane Type your password to allow Installer to make d are eae peters E changes Welcome to the WebClientPlugin 64 Installer Downloads e You will be guided through the steps necessary to Name coodoo install this software r Password Detail Continue Z Cancel r E o Input the name and password of Apple PC and then click OK to install this Active X control After finishing installing the Active X control please quit from the Safari browser Right click Safari icon on the desktop and then select Quit button to quit the browser Then restart Safari browser Input the IP address and http port to go to the login interface of DVR 7 3 2 Via WAN There are also two ways for DVR to connect to Internet 1 Connect the DVR to internet through router or virtual server 44 HD TVI DVR User Manual The network setups are the same as step one to step four of point 1 on WAN of IE remote surveillance Enter WAN IP and http port in the Safari bro
47. on detection recording o Supports recycle after HDD full o Resolution frame rate and picture quality are adjustable o 1 audio channels available e Three record search modes time search event search and image search o 4 8 channels playback simultaneously o Supports deleting and locking the recorded files one by one o Supports remote playback in Network Client through LAN or internet ALARM o Supports schedule for motion detection HD TVI DVR User Manual o Supports pre recording and post recording PTZ CONTROL o Supports various PTZ protocols o Supports 128 PTZ presets and 8 auto cruise tracks o Supports remote PTZ control through internet SECURITY o Customize user right log search system setup two way audio file management disk management remote login live view manual record playback PTZ control and remote live view o Supports administrator and 63 users o Supports event log recording and checking events unlimited NETWORK Supports TCP IP DHCP PPPoE DDNS protocol Supports NAT technology Supports IE browser to do remote view Supports QRCODE Scanning through mobile phone client Supports setup client connection amount Supports dual stream Network stream is adjustable independently to fit the network bandwidth and environment Supports picture snap in remote live Supports remote time and event search and channel playback with picture snap Supports remote PTZ control with preset and auto cruise Suppor
48. ork Configuration Server Enable the auto report in the ECMS NVMS when adding a new device Then input the remaining information of the device in the ECMS NVMS and self define a device ID Input the above mentioned server IP server port and device ID in the server interface Then click Apply button to save the setting Now the ECMS NVMS system will automatically connect this device 4 6 5 NAT D Goto Menu gt Setup gt Network DNAT interface Refer to Fig 4 26 2 Enable NAT and input the NAT Server The default NAT Server is www autonat com 3 Click Apply to save the settings NETWORK Network Sub stream Email Server DA Other Settings NAT Enable Y NAT Server Default Fig 4 26 Network Configuration NAT 4 6 6 Other Settings If your DVR is set to use PPPoE as its default network connection you may set up DDNS to be used in connection The setting steps are as follows Enable DDNS server Select DDNS server Enter user name password and host domain name of the registered website Click Test button to test the effectiveness of the relevant information 6060 25 HD TVI DVR User Manual Click Apply button to save the setting NETWORK Network Sub stream Email Server fother Sos DDNS Y DDNS Type www dwrdydns com Y User Name Password Host Domain DDNS Update Hours Default Apply Fig 4 27 Network Configuration Other Settings Note The domain
49. pply button to save the setting Fig 4 9 Setting Mask Area 4 3 Record Configuration Record configuration includes six sub menus enable record bit rate time recycle record stamp and snap Before Configuration please make sure your DVR has been installed with HDD and has completed its initialization 14 HD TVI DVR User Manual 4 3 1 Enable Goto Menu gt Setup gt Record gt Record interface Refer to Fig 4 10 RECORD Record Bitrate Time Stamp Recycle Record Snap Record Audio Y Default Fig 4 10 Record Configuration Record To enable disable audio recording for the channel Checkmark record and audio Select All to set up the same settings for all channels 4 3 2 Record Bitrate Goto Menu gt Setup gt Record Record Bitrate Refer to Fig 4 11 RECORD Enable Record Bitrate Mime Stamp Recycle Record Snap Resolutio fps i Max Bitrate 1536 kbps 1536 kbps y Default Apply Exit Fig 4 11 Record Configuration Record Bitrate Set up rate resolution quality encode and max bit stream Select All to set the same settings for all channels 4 Click Apply button to save the setting 15 HD TVI DVR User Manual 720P 960H D1 1 30 NTSC Y1 25 PAL 1080P 1 15 NTSC 1 12 PAL This series supports D1 960H 720P 1080P Qualit The higher the value is the clearer the recorded image is Six options uali 7 lowest lower low medium higher and hi
50. rmal schedule setup You can refer to 4 4 1 Schedule for details Note The default schedule of motion based recording is 24 x7 If you want to activate motion based recording you must enable motion alarm and set up schedule for motion alarm see Chapter 4 5 1 Motion Alarm for more details 4 5 Alarm Configuration Alarm configuration includes four sub menus motion video loss other alarm and alarm out 4 5 1 Motion Alarm Motion includes two sub menus motion and schedule The steps to set motion alarm are as follows Goto Menu gt Setup gt Alarm 7 Motion Refer to Fig 4 16 Enable motion alarm set alarm hold time which refers to the time till which the system will wait for further detection of motion e g If the holding time is set to 10 seconds once the system detects a motion it will go into alarm but would not detect any other motion alarm specific to channel until 10 seconds If there is other motion detected during this period it is considered it as continuous movement otherwise it will be considered as a single motion MOTION Schedule Enable Holding Time S Trigger Area Y Setting Setting Setting f Setting Setting Setting Y Y Y f Setting i Setting Default Fig 4 16 Alarm Configuration Motion Click Setting button under the Trigger area Then a window will pop up as below 19 HD TVI DVR User Manual TRIGGER Channel 1 Alarm To Record Buzzer Show Full S
51. s or domain name IE will download ActiveX automatically Then a window pops up and asks for user name and password Input name and password correctly and enter to view Note If you cannot download and install ActiveX please refer to FAQ QS 2 Connect the DVR to internet directly Enter into the DVR s Main Menu gt Setup gt Network interface to enable PPPoE and then input user name and password received from your ISP Next click Apply The DVR 42 HD TVI DVR User Manual will connect to the server and would give a confirmation message When accessing the remote interface of DVR user can input WAN IP to access directly user can enter into Main menu gt Information gt Network interface to check IP address The browser will download Active X control The following setting steps are as the same as 4 and in Point 1 7 3 Remote Surveillance through Apple PC Note Because the current plug in version of client end just only supports 32 bit mode so the safari browser shall start 32 bit mode If the browser is the earlier MACOS version the default setting is 32 bit mode and the setting can be skipped The setting steps are as follows o Right click safari icon and select Show in Finder Select Applications Right click Safari App gt Select Get Info 60 3 3 x SS 3395EE33538F GO 4 57853 6427254732 36 z H 5 Payer ake Alias Remove from Dock Open at Login Show in Find
52. t box and input user name and password 2 Go to configuration interface of the router to map the server port and IP address 1f the user enables UPnP function he can skip this step Click Save button to save the setting 3 Login IE browser and input registered domain name http www xxx dvrdydns com connect to DVR chent You can also quickly register the domain name in this interface 1 Set the IP address manually in the network tab and then click Other Settings tab Check DDNS 2 Select www autoddns com in DDNS Type column as shown above 3 Enter the host name at random like 123 4 Click Register to register the domain name When the successful prompt pops up it means you are successfully register your domain name NETWORK I i Network Sub stream Emall Server M DDNS r DDNS Type nner curbed dim is cam Host Domain aubddns com Register urn F a Default If your IP address is not WAN IP address you should forward your IP address and port in your router or enable UPNP function both in router and DVR Then you can use the domain name 27 HD TVI DVR User Manual plus HTTP port to access your DVR Website provided by dynamic domain name supplier The optional DDNS server www meibu com www dyndns com www dvrdydns com WWW autoddns com www no ip com and mintdns type 4 7 User Management Configuration This tab allows you to add normal or advanced users
53. teries polarity 2 Check the remaining charge in the batteries 3 Check IR controller sensor for any masking If it still doesn t work please change a new remote controller to try or contact your dealers The interface of remote controller is shown below HD TVI DVR User Manual Button Butte UNC Function yt fete rr _ gt Exit _ To exit the cunentineree __ 700 _ gt Direction To move cursor in setup button ZOOM To set picture in picture Kila To control playback Play Pause Stop Previous Section Next Section Rewind Fast Forward SEQ To enter auto dwell mode Get information about DVR like firmware version INFO j j HDD information 2 5 Control with Mouse 2 5 1 Connect Mouse It supports USB mouse through the ports on the rear panel If mouse is not detected or doesn t work check below steps 1 Make sure the mouse is plugged in the USB mouse port 2 Try with a good know mouse 2 5 2 Use Mouse During live Double click on any camera window to see the full screen Double click again to return to the previous screen Right click to reveal the control menu on the screen Right click again to hide the menu In Configuration Click to enter a particular option Right click to cancel the option or to return to the previous menu In order to input a value in a particular screen move cursor to the input box and click An input window will appear as below It supports digits alphabets and sym
54. the resolution of the VGA HDMI output Front panel II Power Indicator when connected the light is blue HDD indicator The light turns blue when reading writing HDD The light turns blue when it is able to access the network Multi screen Backup indicator The light turns blue when backing up files and data Change screen display mode like1 4 9 16 channel Connect to USB mouse or USB storage device 2 3 Rear Panel Instructions _ Ww M ww i Redes z Rear Panel for 4 CH HD TVI DVR User Manual y o OO O00 HD TVI VIDEO IN HDMI VGA Rear Panel for 8 CH A E VOQGODODO j SADO S OS Rear Panel for 16 CH Descriptions DC12V Power Input U To connect external USB devices like USB mouse or USB storage device HDMI HDMI Port Connect to high definition display device GA VGA Port Connect to monitor VGA Port Connect to monitor Support HD TVI signal 1080P 25 30fps 720P 25 30 50 60fps analog signal 960H D1 video input AUDIO OUT Audio output connect to the sound box AUDIO IN 1 CH Audio Input RS485 Connect to keyboard or speed dome A is TX B is TX HD TVI VIDEO IN 2 4 Remote Controller It uses two AAA size batteries Open the battery cover of the remote controller Place batteries Please take care the polarity and Replace the battery cover Key points to check in case the remote doesn t work 1 Check bat
55. to display all the available cameras E Zoom Single channel large screen electronic amplification Audio Enable sound PTZ Click the PTZ button to control rotation position speed and auto scan of the PTZ Snap Click this button to snap the live pictures These pictures will automatically be saved in the SATA disk Record Click this button to start stop recording Playback Click this button to playback the record files Click Main Menu button to pop up a window as Fig 4 2 You can also press MENU button on the front panel or operate with remote controller to display the main menu Clicking Setup icon will pop up the configuration menu MAIN MENU ill Information Disk Managerrent Upgrade ggal Shut Doser Fig 4 2 Setup 4 1 Basic Configuration Basic configuration includes three sub menus system date amp time and DST 10 HD TVI DVR User Manual 4 1 1 System Go to Menu gt Setup gt Basic gt System interface Refer to Fig 4 3 BASIC System LES amp Time DST Device Name Device ID Video Format Password Check Show System Time Max Online Users Video Output VGA 800X600 Language English Logout After Minutes Never Default Fig 4 3 Basic Configuration System In this interface you can set up the device name device ID video format max network users VGA resolution language and so on The definitions for every parameters display as below Device Name The name of the device It may displ
56. ts remote full menu setup changing all the DVR parameters remotely Supports mobile surveillance by phones with iPhone Android amp Blackberry OS Supports CMS NVMS to manage multi devices on internet HD TVI DVR User Manual 2 Hardware Installation 2 1 Install Hard Drive Check the unit and the accessories after getting the DVR Please don t power up the unit till the physical installation is complete Notice 1 This series support one SATA hard drive Please use the hard drive the manufacturers recommend specially for security and safe field 2 Please calculate HDD capacity according to the recording setting Please refer to Appendix B Calculate Recording Capacity 1 Loosen the screws on the back and side Take out the HDD of the device to remove the cover Q Put the HDD on the bottom of the 4 Turn over the device and fix the HDD device with the screws Ph 5 Connect the power and data cables 6 Install the cover back and fix it with the screws Note For convenience installation please connect the power and data cables first and then fix the HDD with the screws HD TVI DVR User Manual 2 2 Front Panel Descriptions Notice The front panel descriptions are only for reference please make the object as the standard Front panel I When recording the light is blue Net n Net When access to network the light is blue Power indicator when connection the light is blue Switch
57. uld like your DVR to automatically obtain an IP address and other network settings check the checkbox beside Obtain an IP address automatically Then the device will distribute IP address subnet mask and gateway IP and DNS server gt Ifyou want to configure your own settings disable Obtain an IP address automatically item and input the IP address subnet mask gateway IP and DNS server gt If you connect internet through PPPoE disable Obtain an IP address automatically item and check PPPoE checkbox and then enter username and password Once the setup is completed your DVR will automatically dial up into your network Test the effectiveness of the network by clicking Test button after you set up the network Ifthe network is well connected please click Apply button to save the setting 4 6 2 Sub Stream To set up sub stream Goto Menu gt Setup gt Network gt Sub Stream interface Refer to Fig 4 23 NETWORK Network Sub stream Email Server INAT Other Settings Remaining 64 CIP ir viisxie Fllcer 7 512 kbps y f Default Fig 4 23 Network Configuration Sub Stream 23 HD TVI DVR User Manual i eee A REA FPS Range from 1 25 Resolution Support CIF The quality of the clients image The higher the value is the clearer the ANI J AE E Quality l i record image Six options lowest lower low medium higher and highest Encode VBR and CBR Max
58. wser to install the Active control The concrete steps are the same as step 5 and 6 of Chapter 7 2 1 2 Connect the DVR to internet directly The network setups are the same as step one of point 2 on WAN of IE remote surveillance Enter WAN IP and http port in the Safari browser to install the Active control The concrete steps are the same as step 5 and 6 of Chapter 7 2 1 7 4 The Remote Live Preview Mester Stream Sub trean Mo Loca Recording Status 12349 ie 10 b O K fi Fig 7 1 Remote Live Preview Interface Channel indicator i Screen display mode Voume L Snapping picture Start IE record Bidirectional talk Playback PTZ control Master sub stream status o Note Click button to start recording The record file will be saved in user s PC Screen display mode Click the icon beside the screen display mode to select channels 45 HD TVI DVR User Manual Snap pictures Click Snap icon to automatically capture pictures and save those pictures in the computer You can set up the save path for those picture in the Remote Preview interface gt Configuration gt Local configuration PTZ control Please connect speed dome to the device via RS485 firstly make sure the protocol of the speed dome is supported by the device and set the relative parameters manually User can control the dome up down right left or stop rotating on Control Center adjust rotatio

DVR User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents