User Manual - eStore.com.au
Contents
1. ACTI Connecting Vision DA Hardware Manual Other Adjustments and Accessories How to Remove the Pigtail For applications that may require the use of the Ethernet port at the back of the camera remove the pigtail from the camera Follow the procedures below 1 Loosen the four 4 screws to remove the back cover of the camera 2 Disconnect the network cable from the Ethernet port and let it loose NOTE This network cable is the other end of the pigtail 2 ACTI Connecting Vision bis Hardware Manual 3 Using the bundled camera base wrench detach the two 2 screws to remove the bracket 4 Remove the clamping nut and sealing insert 5 Remove the rubber from the dome cover 5 6 Remove the gland body from the camera www acti Com ACTI Connecting Vision bis Hardware Manual 7 Remove the sealing insert and clamping nut from the cable and then pull out the pigtail from the bracket 8 Using a coin or screwdriver remove the cap from the back cover Then attach the cap to close the cable hole 9 Attach the bracket to the camera 10 Attach the back cover of the camera as needed 4 ACTI Connecting Vision V iA Hardware Manual How to Insert a Memory Card The camera supports local video r2. ACTI Connecting Vision DM Hardware Manual 5 Insert the sealing insert and attach it at the end of the flex conduit 6 Pull the device cables through the gland body 7 Attach the terminal blocks see Other Connections on page 36 for more information 8 Connect the cables to the corresponding connectors on the camera VVAVAVAYA Aol LUO aa ACTI Connecting Vision DA Hardware Manual 9 Align the camera cover and tighten the four 4 screws to secure the camera cover u sing the hex screwdriver NOTE Make sure the cover rubber black is intact and properly aligned to the cover 10 Insert the sealing insert with claw into the gland body and then attach the clamping nut to complete the cable solution NOTE Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly 35 D4 ACTI Connecting Vision Hardware Manual Other Connections This section describes the procedures in preparing the external devices that you can connect to the camera The camera supports DC12V power input Digital Inout and Output DI DO and Audio Input and Output devices using the bundled terminal blocks The use of these devices however is optional Connecting a Power Adapter Optional In case of using a non PoE switch or your PoE switch has limited power supply you
3. of the camera using the bundled female conduit gland and flexible conduit This is the recommended solution if an exterior grade Ethernet cable is not available The camera may or may not have to be installed first before doing the cable connections see related installation procedures for details Before connection prepare the following materials Female Conduit Gland Flexible Conduit 1 2 Trade size included in the camera package not included in the package r NOTE Not included in the package Washer Ethernet Cable CAT 5 or CAT 6 included in the camera package E a b Perform the following to waterproof the pigtail using the female conduit gland 1 Disassemble the female conduit gland as shown below 8 Sealing Clamping Cable Gland Nut Nut EE 22 ACTI Connecting Vision gt Hardware Manual 2 Pull the Ethernet cable through the flex conduit Leave enough length of the cable outside the flex conduit Insert the clamping nut into through the flex conduit Insert the sealing nut and fix it at the end of the flex conduit 5 Insert the gland body into the Ethernet cable gt 23 ACTI Connecting Vision DM Hardware Manual 6 On the pigtail side insert the washer into the pigtail 7 Connect the Ethernet cable connector to the pigtail connector
4. Zoom Bullet Series Hardware Manual B41 B44 B45 B46 B47 B49 B410 144 145 147 2015 05 18 MJ ACTi Connecting Vision DA ACTI Connec ting Vision Hardware Manual Table of Contents OS aaa ct sang AG NAN BEA ecg ete E CAN NUN KANA IA 4 Safety Instructions ccccceeeeeeeeseesenseeeeneeeeenseeeesseseeseesenseesenseseensesoeneeses 6 Jigolo lI eilel p Peet aaa aaa a eect Aya a a anana a eee Wana se BN em errr 7 The List Of Models 0 ccccceseeneceeeceseenseenseeneceseceseenseonseonssensenseoneeenseoness 7 PACKAGE COMON S kaanan aj cece na aa E AE KA GAE RNB RA KANE HA AA NG A EE 8 PNYSICAl DESCHIDUION aaa sasi jawa aaa aaa daana jakin gan ent vous aia aa aja a a a ana aaa 10 Mounting Options ccceceeeeseeseeseecenseecenseseenseeoeseesenneesensessonseseensesoees 12 Installation Procedures sasasasananananaenananananae 13 Step 1 Prepare for Installation cccsseeeeseeeeneeeeneeceeeeceneeeeneeeeneees 13 Step 2 Attach the Sunshield ccssecceseeeseeeceneeceneeseneeceneeeeneeseneees 14 Step 3 Install the Camera ccccssceeeseeceneeeeneeeeneeceneeeensecenesseneeseneees 15 Step 4 Waterproof and Connect the Network Cable 00000 15 Step 5 Connect to Network cccssceseseecnseeceneecenseceneecenseceneeseneeseneees 16 Step 6 Access Camera Live View sisccissesesecscusesenscanusesunnscoutexnsedasuasxwadaens 16 Ste
5. You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically This connection uses the following items a Use the following IP address o Client for Microsoft Networks 2 VirtualBox Bridged Networking Driver aos Packet Scheduler File and Printer Sharing for Microsoft Networks Intemet Protocol Version 6 TCP IPv6 IP address 192 168 0 99 Subnet mask wida FOE a ae LG A Default gateway intemet Protocol Version 4 TCP Pv4 sika Link Layer Topology Discovery Mapper O Driver sika Link Layer Topology Discovery Responder Obtain DNS server address automatically KK KS KS KK KK Use the following DNS server addresses Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Preferred DNS server Alternate DNS server _ F Validate settings upon exit s r OK Cancel ACTI Connecting Vision DM Hardware Manual Manually adjust the IP addresses of multiple cameras If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them all of the cameras would then have the initial IP address o
6. 03 09 AC Megapixel IP Dome E92 A XX 13D 00321 228 5 6 1 172 16 26 90 00 0F 7C 0A A1 4B ENR 010 V4 00 00 AC 16 CH Embedded NVR ENR1200 ENR1200 A 13D 00006 172 16 26 85 00 0F 7C 0B 36 8D A1D 500 V6 04 15 AC Hemispheric Camera E96 A XX 13H 00023 228 5 6 1 172 16 26 95 00 0F 7C 0B B7 50 A1D 500 V6 05 16 AC Hemispheric Camera BSS A XX 131 00007 16 26 00 0F 7C 8D F1 0A 1D 500 V6 05 i i 01 174 172 16 26 82 00 0F 7C 97 57 CD A1D 310 V4 12 09 AC Megapixel IP Camera TCM3511 12J X 00334 Ai Remove ea some 4 You can quickly notice the camera model in the list Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already 7 ACTI Connecting Vision DM Hardware Manual Use the default IP address ofa camera If there is no DHCP server in the given network the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment When the camera is plugged into network and it does not detect any DHCP services it will automatically assign itself a default IP 192 168 0 100 Whereas the default port number would be 80 In order to access that camera the IP address of the PC has to be configured to match the network segment of the camera Manually adjust the IP address of the PC
7. AC The illustration below is a graphic example of connecting a relay to a high voltage DO device 110V 220V AC External Power Source DO1 Device 4 ark g Camera Illuminator NOTE For more information on DI DO connections please refer to the Knowledge Base article All About Digital Input and Digital Output downloadable from the link below http Download acti com id 516 10 ACTI Connecting Vision DA Hardware Manual How to Connect Audio Devices Audio input output devices such as an active microphone or speaker can be connected to the camera using the supplied terminal block Press and hold the orange tab as you insert the wire through the pin slot then release the orange tab to secure the wire The terminal block that comes with the package may either be DI DO and Audio Terminal Block For Audio Use i For Audio Use To connect audio devices map the pins to one of the pin combinations below Device Pin Mapping Instructions AO _ GND Connect the wires of the audio output device to Audio Output AO put AO A OUTorao AO_GND and A_OUT or AO AI GND Connect the wires of the audio input device to Audio Input A1 put A IN or AI AI GND and A IN or Al NOTE For more information about AUDIO in connections please refer to the Knowledge Base article How to Use Audio in of ACTi Cameras downloadable from the link below http Download acti com id 534
8. Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B C digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications to the equipment that are not expressly approved by the responsible party for compliance could void the user s authority to operate the equipment European Community Compliance Statement C 4 This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European St
9. See How to Use the Male Conduit Gland on page 32 NOTE The flex conduit is not included in the package and must be purchased separately 6 ACTI Connecting Vision DA Hardware Manual Before connecting any devices to the camera connectors remove the back cover first 1 Using the bundled hex screwdriver loosen the four 4 screws to remove the back cover NOTE The network cable connected to the Ethernet port is the other end of the pigtail If the pigtail will not be used to connect the camera to the network disconnect this cable and remove the pigtail from the camera see How to Remove the Pigtail on page 42 for detailed information MICRO SD 12345678 DC ono 2 Using a coin or screwdriver remove the cap from the back cover Then set the back cover aside for later use 7 ACTI Connecting Vision DA Hardware Manual How to Use the Male Cable Gland Optional This section describes how to waterproof the cable using the male cable gland This solution is useful only when you need to replace the cable out or pigtail of the camera see How to Remove the Pigtail on page 42 for detailed information For normal applications the use of pigtail is sufficient and there is no need for replacement Before connection prepare the following materials Male Cable Gland Exterior Grade Ethernet Cable included i
10. Sticker Drill Template 8 www acti com ACTI Connecting Vision DM Hardware Manual Terminal Block Terminal Block for Power for Audio and DI DO Quick Installation Guide Step 1 Unpack the Device Cech the carana padhanga and maba sara at tores ase preset The Corrpete package hu n chown on the Carers Harda Vares Step 2 Mount the Device OR z Mareng vases par camara Team Check te mod sutte marang a Fett Yorn Pre Hardware Manasa o Fore cus Mir ng Area MAN LIM 4 la A kangh ah aa LANG NA Tigel as AI a uthi aa Step 3 Connect the D J o ne vaf wi Basic Comnecnom Esampie Warranty Card NOTE The pictures are for reference only Actual items may slightly vary 9 www acti com MA ACTI gt Connecting Vision Hardware Manual Physical Description Exterior View Connectors View WAN MICRO SD va 12345678 ETHE Mi r oc GNO 7y NOTE The connectors are hidden under the housing cover 1 Ethernet Ports The Ethernet port 1a of the cable out or pigtail connects to a network using an Ethernet cable The Ethernet port 1b on the housing connects the cable out or pigtail to the camera NOTE It is possible to replace the pigtail with a standard Ethernet cable by disconnecting the pigtail and connecting the preferred cable to this port 2 Memory Card Slot Insert a memory card into this slot for local recording purposes See How to I
11. can purchase a power adapter and directly connect the camera to a power outlet The power adapter must be connected to the supplied terminal block before use To do this follow the procedures below 1 Loosen the screws of the 12V and GND pins of the power terminal block 2 Take note that a standard power adapter cable has two 2 different wires Connects to GND Pin White stripe Connects to 12V Pin 6 ACTI Connecting Vision DA Hardware Manual 3 Connect the wire with the white stripe to the 12V pin and the other to the GND pin NOTE The terminal block pictures are for reference only note that actual label placement may vary per model 4 Tighten the screws of the 12V pin and the GND pins to secure the wire connection 5 Set the prepared power adapter for connection later Below is an example of a power adapter with an attached terminal block NOTE The power adapter is not bundled in the package 7 ACTI Connecting Vision DA Hardware Manual Connecting DI DO and Audio Devices Optional Depending on your surveillance needs you may connect digital input output or audio input output devices to your camera The camera comes with one 1 terminal block for both digital and audio input output devices How to Connect DI DO Devices Digital Input DI devices can be used to notify the camera about an activity in the camera site DI can
12. package not included in the package NOTE Exterior grade cables are already waterproof Not included in the package Washer included in the camera package Perform the following to waterproof the pigtail using the female cable gland 1 Disassemble the female cable gland as shown below E eB Cable Gland Sealing Clamping Insert Nut 9 ACTI Connecting Vision DA Hardware Manual 2 Insert the clamping nut into the Ethernet cable 3 Insert the sealing insert with claw 4 Insert the gland body into the Ethernet cable 5 On the pigtail side insert the washer into the pigtail 20 DM ACTI Connecting Vision Hardware Manual 6 Connect the Ethernet cable connector to the pigtail connector MO 7 Attach the gland body to the pigtail NOTE Make sure the gland body is tightly attached to the pigtail and the washer is secured between them 8 Insert the sealing insert into the cable gland body and then attach the clamping nut to complete the cable solution NOTE Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly 2 ACTI Connecting Vision DA Hardware Manual How to Use the Female Conduit Gland This section describes how to waterproof the cable out or pigtail
13. D lights up 6 Power LED The Power LED lights red when the camera is powered on and goes off once the camera boot up process is complete NOTE For typical use the power LED is hidden inside the housing and cannot be seen However knowing how the power LED works is essential when troubleshooting or doing a reset ACTI Connecting Vision DA Hardware Manual Mounting Options There are several mounting options that you can use to install the camera Select the most Suitable solution for your installation environment Mount Types Accessories Wall Mount Suitable when mounting the camera directly on walls using the integrated bracket See Installation Procedures on page 13 Gang Box Suitable for locations which require the use of gang boxes The Gang Box Converter Converter is attached to the gang box while the camera with its bundled bracket is installed on the Gang Box Converter All cables are hidden inside the gang box PMAX 0806 Ceiling Mount Suitable when mounting the camera on the ceiling The integrated bracket must be removed from the camera first PMAX 1300 Vertical Pole Suitable when mounting the camera on vertical poles MUNI PMAX 0504 e For more information about the mounting solutions and accessories please check the Mounting Accessory Selector in our website http www acti com mountingselector e The above mounting accessories are not included in the package Contact your sal
14. In the following example based on Windows 7 we will configure the IP address to 192 168 0 99 and set Subnet Mask to 255 255 255 0 by using the steps below xe lt All Control Panel Items b Network and Sharing Center A E a Vian cad E gga O G M Control Panel Home i al o Di ais Di View your basic network information and set up connections rganize v isable this network device iagnos Ch P EE ae See full map Tadi 7 aaa a LA je td A Local Area Connection Ch d d shari J ae e SISO_NP_PC1 Network Internet Ue Nang ga This computer ae Intel R 8 i Disable View your active networks Connect or disconnect Status Diagnose jp Network Access type Internet Work network Connections g Local Area Connection B Bridge Connections Create Shortcut Change your networking settings a Set up a new connection or network x Delete Set up a wireless broadband dial up ad hoc or VPN connection or set up a router or la Rename access point Wi Properties gw Connect to a network ae Connect or reconnect to a wireless wired dial up or VPN network connection 2EE also HomeGroup Choose homegroup and sharing options Internet Options Access files and printers located on other network computers or change sharing Windows Firewall ae btocol Version 4 TCP IPv4 Properties b jamban ee ee ee Connect using amp Intel R 82567LM 3 Gigabit Network Connection
15. ady for the access from the PC The user however might not know the IP address of the camera yet It is necessary to know the IP address of the camera in other to be able to access it by using a Web browser The quickest way to discover the cameras in the network is to use the simplest network search built in the Windows system just by pressing the Network icon all the cameras of the local area network will be discovered by Windows thanks to the UPnP function support of our Cameras In the example below we successfully found the camera model that had just connected to the network ees o RF wwe ge bos Ge gt Network gt v Search Network p File Edit View Tools Help Organize v Search Active Directory Network and Sharing Center gt gt i 1 B55 A XX 131 00007 b 4 Favorites 1 B87 A 01 00A 61706 E Desktop D31 A XX 13B 00159 D42 A XX 13C 00132 D51 A 02 12H 00010 A XX 12L 00286 A XX 12L 00107 A XX 12K 00147 A XX 13C 00126 A XX 13D 00131 A XX 13A 00061 A XX 13A 00089 A XX 13D 00321 E96 A XX 13H 00023 my Downloads Recent Places d4 N ow Libraries G T Ww j Computer m m mo g t Network Baa Q Q Q Q Q Q Q Q Q Q Q Q B55 A XX 131 00007 Categories Other Devices Network location ACTi com www acti com ACTI Connecting Vision DA Hardware Manual Double click on the camera model name the
16. andard EN 55022 and EN 55024 In a domestic environment this product may cause radio interference in which cause the user may be required to take adequate measures 5 www acti com DM ACTI Connecting Vision Hardware Manual Safety Instructions Cleaning Disconnect this product from the power supply before cleaning Accessories and Repair Parts Use only the accessories and repair parts recommended by the manufacturer Water and Moisture Install other devices such as PoE injector alarm etc that will be used with the camera in a dry place protected from weather Servicing Do not attempt to service this product yourself Refer all servicing to qualified service personnel Damage Requiring service Disconnect this product from the power supply immediately and refer servicing to qualified service personnel under the following conditions 1 When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the product 3 Ifthe inner parts of product have been directly exposed to rain or water Ifthe product does not operate normally by following the operating instructions in this manual Adjust only those controls that are covered by the instruction manual as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation Safety Check Upon completion of any service
17. be triggers of events For example you can connect a panic button to the camera as such when the panic button is pressed the alarm signal will be sent through the camera Other common DI device applications are emergency button smoke detector passive infrared sensor etc Digital Output DO devices are external devices that are activated by the camera upon an event inside the camera For example you can connect an alarm horn to the camera as such when an event occurs inside the camera e g detected intruder the alarm horn will sound Other common DO device applications are motion triggered lights electric fence magnetic door locks etc Press and hold the orange tab as you insert the wire through the pin slot then release the orange tab to secure the wire The terminal block that comes with the package may either be one of the following DI DO and Audio Terminal Block For DI DO Use 7 26 oo oo A For DI DO Use To connect digital input output devices DI DO map the pins to one of the pin combinations below Device Mapping Instructions Pin DIO PW or Connect the wires of the output device to DIO PW or Digital Output DO 12V 12V and DO DIO GND Connect the wires of the input device to DIO GND Digital Input DI ooo ana Dk www acti Com DA ACTI Connecting Vision Hardware Manual The table below shows the DI DO connection specifications Device Connection Connection des
18. ble s using the bundled male conduit gland and flexible conduit This is the recommended solution if other devices such as an audio or digital input output device will be connected to the camera or when the use of a power adapter is necessary All the device cables including the power adapter and Ethernet cable can be housed inside the flex conduit The camera may or may not have to be installed first before doing the cable connections see related installation procedures for details Before connection prepare the following materials Male Conduit Gland Flexible Conduit 1 2 Trade size included in the camera package not included in the package NOTE Not included in the package Perform the following to use the male conduit gland solution 1 Disassemble the male conduit gland as shown below Nut Sealing Insert P ii Nut NOTE In this installation the conduit gland body can be securely attached to the mount kit therefore the use of lock nut is not necessary Please set the lock nut aside 32 ACTI Connecting Vision DA Hardware Manual 2 Attach the gland body to the hole of the cover 3 Pull enough length of the device cables without connectors through the flex conduit The terminal blocks will be attached once the cable passes through the gland body and cover later 4 Insert the clamping nut through the flex conduit 33
19. cccccsesccceeecesseseeeeeeeeseeeeesaeeeeas 45 Accessing the Camera ccssccsseceseceneseneeeneees 46 Configure the IP Addresses cccesseccesseecesseecenseecenseeeenseeeenseseeneesoens 46 Access the Cam ra aia aan jana aaa ana gaga aaa aaa a 50 3 www acti com D4 ACTI Connecting Vision Hardware Manual Precautions Read these instructions Read all the safety and operating instructions before using this product Heed all warnings Adhere to all the warnings on the product and in the instruction manual Failure to follow the safety instructions given may directly endanger people cause damage to the system or to other equipment Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Trademarks ACTi and ACTi logo are registered trademarks of ACTi Corporation All other names and products used in this manual are registered trademarks of their respective companies Liability Every reasonable care has been taken during the writing of this manual Please inform your local office if you find any inaccuracies or omissions ACTi will not be held responsible for any typographical or technical errors and reserves the right to make changes to the product and manuals without prior notice 4 www acti com D4 ACTI Connecting Vision Hardware Manual Federal
20. default browser of the PC is automatically launched and the IP address of the target camera is already filled in the address bar of the browser lf you work with our cameras regularly then there is even a better way to discover the cameras in the network by using IP Utility The IP Utility is a light software tool that can not only discover the cameras but also list lots of valuable information such as IP and MAC addresses serial numbers firmware versions etc and allows quick configuration of multiple devices at the same time Search and downloand IP Utility for free from hitp www acti com DownloadCenter With just one click you can launch the IP Utility and there will be an instant report as follows IP Address NetMask 172 16 26 80 255 255 255 0 v Basic Search Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot Account Password 123456 Total 50 IP Address MAC Address FW Version Model Serial No Multicast IP Status 172 16 26 6 00 0F 7C 0A 3F EA A1D 500 V6 04 15 AC Megapixel IP Camera D31 A XX 13B 00159 228 5 6 1 z 172 16 26 7 00 0F 7C 0A 55 54 A1D 500 V6 04 15 AC Megapixel IP Dome E61 A XX 13C 00126 228 5 6 1 172 16 26 2 00 0F 7C 0A 93 52 A1D 500 V6 03 17 AC Megapixel IP Camera D42 A XX 13C 00132 228 5 6 1 172 16 26 13 00 0F 7C 0A 99 91 A1D 500 V6 04 15 AC Megapixel IP Dome E61 A XX 13D 00131 228 5 6 1 172 16 26 12 00 0F 7C 0A A1 0F A1D 500 V6
21. ecording or saving of snapshots to a memory card NOTE Supports microSDHC and microSDXC cards How to Insert the Memory Card 1 Open the back cover of the camera 2 Insert a memory card into the card slot with the metallic contacts facing down Push the card until it clicks into place 12345678 How to Remove the Memory Card In case there is a need to remove the card make sure to access the camera Web Configurator to safely unmount the card first see the camera Firmware manual for more information Once unmounted from the firmware push the card to eject it from the slot is D4 ACTI Connecting Vision Hardware Manual Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC both the camera and the PC have to be within the same network segment In most cases it means that they both should have very similar IP addresses where only the last number of the IP address is different from each other There are 2 different approaches to IP Address management in Local Area Networks by DHCP Server or Manually Using DHCP server to assign IP addresses If you have connected the computer and the camera into the network that has a DHCP server running then you do not need to configure the IP addresses at all both the camera and the PC would request a unique IP address from DHCP server automatically In such case the camera will immediately be re
22. es agents to purchase 2 D4 ACTI Connecting Vision Hardware Manual Installation Procedures This section describes the procedures in installing the camera on the wall using the integrated bracket IMPORTANT Before installation make sure the wall can bear more than the weight of the camera and its bracket NOTE The following procedures and pictures are based on the cable going along the wall same procedures apply when the cable will pass through the wall unless otherwise specified Step 1 Prepare for Installation 1 Depending on the wall material purchase applicable screws and screws plugs as needed that can hold the camera and bracket weight on the wall 2 Attach the supplied drill template sticker on the wall 3 Determine how the cable will be routed pass through the wall or along the wall e Ifthe cable will pass through the wall drill the cable hole and the four 4 screw holes on the wall R507 00064 000 Cable hole Smm Through Wall Optional eo n eam e 5 fe a ej 4 a Srst 9Imn Drill Template scale 1 1 e Ifthe cable will be routed along the wall just drill the four 4 screw holes on the wall 4 Detach the drill template sticker from the wall and insert the plastic plugs into the screw holes 9 ACTI Connecting Vision bis Hardware Manual Step 2 Attach the Sunshield 1 Loosely secure the supplied screws to attach the
23. esses starting from 192 168 0 101 In case there are 20 cameras selected the last one of the cameras would have the IP 192 168 0 120 Later by pressing the Refresh button of the IP Utility you will be able to see the list of cameras with their new IP addresses Please note that it is also possible to change the IP addresses manually by using the Web browser In such case please plug in only one camera at a time and change its IP address by using the Web browser before plugging in the next one This way the Web browser will not be confused about two devices having the same IP address at the same time 1 DA ACTI Connecting Vision Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment it is possible to use the Web browser of the PC to access the camera You can use any of the browsers to access the camera however the full functionality is provided only for Microsoft Internet Explorer The browser functionality comparison Functionality Internet Explorer Other browsers Live Video PTZ Contro Capture the snapshot Video overlay based configuration Motion Detection regions Privacy Mask regions All the other configurations When using non Internet Explorer browsers free third party software plug ins must be installed to the PC first to be able to get the live video feed from the camera Brow
24. f 192 168 0 100 which is not a proper situation for network devices all the IP addresses have to be different from each other The easiest way to assign cameras the IP addresses is by using IP Utility g IP_Utility IP Address NetMask 172 16 26 192 255 255 255 0 Basic Search T O Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Save amp Reboot ni ao Total 56 Account Password 123456 Http Port w IP Address MAC Address FW Version Model Serial No Multicast IP Status 172 16 26 2 00 0F 7C 07 DE 65 A1D 311 V5 07 05 AC Hemispheric Camera KCM3911 228 5 6 1 172 16 26 4 00 0F 7C 08 17 C2 A1D 310 V4 12 02 AC Mega IP Camera TCM1111 228 5 6 1 172 16 26 6 00 GE ares Ea KCM7311 228 5 6 1 172 16 26 7 00 TCM6630 228 5 6 1 172 16 26 10 00 Dynamic IP Address TCM4201 228 5 6 1 172 16 26 11 00 4 KCM3911 228 5 6 1 172 16 26 13 00 KCM5111 228 5 6 1 172 16 26 40 00 KCM5211 228 5 6 1 172 16 26 41 00 i KCM5311 228 5 6 1 172 16 26 50 00 3 z z KCM5111 228 5 6 1 172 16 26 52 00 a a KCM5311 228 5 6 1 172 16 26 53 00 2 J TCM5311 228 5 6 1 172 16 26 54 00 TCM5611 228 5 6 1 172 16 26 55 00 EN Ar NEG TCM5111 228 5 6 1 172 16 26 57 DONVITO TCD2100 228 5 6 1 172 16 26 61 TCM1231 228 5 6 1 Sess With the procedure shown above all the cameras will have unique IP addr
25. hg 8 Attach the gland body to the pigtail map NOTE Make sure the gland body is tightly attached to the pigtail and the washer is secured between them 24 DM ACTI Connecting Vision Hardware Manual 9 Push the flex conduit and insert the sealing nut into the gland body M gt NOTE Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly 10 Attach the clamping nut to complete the cable solution 2 pq ACTI Connecting Vision Hardware Manual Waterproof Solution Using the Camera Connectors For more flexible applications use the connectors at the back of the camera to connect a power adapter or other devices Or in some cases users may require the use of specific cables with customized length In such cases use one of the following solutions Bundled Accessory Description Male Cable Gland Optional Use this solution if the pigtail must be replaced with a different cable The replacement cable must also be Exterior grade that will be connected to a PoE switch injector See How to Use the Male Cable Gland on page 28 Male Conduit Gland Use this solution when connecting other devices such as audio or digital input output devices or a power adapter when PoE is not available A flexible conduit trade size 1 2 is required to house all the cables
26. his solution when connecting an Exterior grade Ethernet cable between the camera and a Power over Ethernet PoE switch or injector See How to Use the Female Cable Gland on page 19 Female Conduit Gland Use this solution when connecting a standard indoor Ethernet cable between the camera and a Power over Ethernet PoE switch injector A flexible conduit trade size 1 2 is required to house the Ethernet cable See How to Use the Female Conduit Gland on page 22 NOTE The flex conduit is not included in the package and must be purchased separately If other devices such as a power adapter digital or audio input or output devices will be connected to the camera or in some cases users may require the use of specific cables with customized length use the back connectors of the camera to connect the cables See Waterproof Solution Using the Camera Connectors on page 26 for cabling information s ACTI Connecting Vision DA Hardware Manual How to Use the Female Cable Gland This section describes how to waterproof the cable out or pigtail of the camera using the bundled female cable gland An exterior grade Ethernet cable is required The camera may or may not have to be installed first before doing the cable connections see related installation procedures for details Before connection prepare the following materials Female Cable Gland Exterior Grade Ethernet Cable included in the camera
27. ign TTL compatible logic levels To trigger low Logic level 0 OV 0 4V Voltage Normal high Logic level 1 3 1V 30V Connection design Transistor Open Collector Voltage amp Current lt 24V DC lt 50mA Typical Connection Based on these specifications if the DI device has a voltage of OV 30V or the DO device has a voltage of lt 24V lt 50mA then the camera can supply internal power to these devices and there is no need to connect the DI DO device to an external power source In this case use the DIO GND and DI pins to connect a DI device and use the DIO PW or 12V and DO pins to connect a DO device See wiring scheme below NORMAL 3 1V NORMAL HIGH TRIGGER LOW 24vDC 39 D4 ACTI Connecting Vision Hardware Manual High Voltage DO Device Connection Even though the camera provides 12V power this may not be enough for some high voltage DO devices such as a Ceiling light or a motor that opens or closes a gate In this case there is a need to connect an external relay See wiring scheme below NORMAL HIGH TRIGGER LOW x AC110Vv Wi Mia MOTOR Note that when choosing an appropriate relay please refer to its specifications and make sure they match the above design The triggering circuit voltage has to be around 12V DC and the switch controlled circuit voltage has to match the external power supply e g 110V AC or 220V
28. n the camera package not included in the package NOTE Exterior grade cables are already waterproof Not included in the package Perform the following to use the male cable gland solution 1 Disassemble the male cable gland as shown below Body Sealing Insert Clamping with Washer with Claw Nut 2 ACTI Connecting Vision DA Hardware Manual 2 Insert the clamping nut into the Ethernet cable 3 Insert the sealing insert with claw 4 Attach the gland body to the hole of the cover gt ACTI Connecting Vision DM Hardware Manual 5 Insert the Ethernet cable through the cable gland and connect it to the Ethernet port of the camera 6 Tighten the four 4 screws to secure the camera cover using the hex screwdriver NOTE Make sure the cover rubber black is intact and properly aligned to the cover 30 ACTI Connecting Vision DM Hardware Manual 7 Insert the sealing insert with claw into the gland body 8 Attach the clamping nut to complete the cable solution NOTE Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly 31 ACTI Connecting Vision gt Hardware Manual How to Use the Male Conduit Gland This section describes how to waterproof the ca
29. nsert a Memory Card on page 45for more information NOTE Supports microSDHC and microSDXC cards 0 D4 ACTI Connecting Vision Hardware Manual 3 Digital Input Output DI DO and Audio Input Output This connector connects to digital input or output devices such as an alarm trigger panic button etc as well as audio input and output devices such as microphones and speakers Digital Input DI and Digital Output DO devices are used in applications like motion detection event triggering alarm notifications etc See Connecting DI DO and Audio Devices Optional on page 38 for information 4 DC 12V Power Input In case the camera is connected to a non PoE Power over Ethernet switch use this connector to connect the camera to an external power adapter not included See Connecting a Power Adapter Optional on page 36 for more information 5 Reset Button The purpose of reset button is to restore the factory default settings of the camera including the administrator s password The reset button can be used for following purposes e The administrator s password has been forgotten and therefore the camera cannot be accessed e Incase of IP address mask or allow deny filter related issues resulting with inability to modify these settings e Incase of connectivity issues or abnormal video quality How to do the reset properly Press and hold the reset button for 5 seconds or until the power LE
30. or repairs to this product ask the service technician to perform safety checks to determine if the product is in proper operating condition 6 www acti com D4 ACTI Connecting Vision Hardware Manual Introduction The List of Models This hardware manual contains the following models 5MP Zoom Bullet with D N Adaptive IR Basic WDR 12x Zoom lens 1 3MP Zoom Bullet with D N Adaptive IR Basic WDR SLLS 10x Zoom lens 2MP Zoom Bullet with D N Adaptive IR Basic WDR SLLS 10x Zoom lens SMP Zoom Bullet with D N Adaptive IR Basic WDR 10x Zoom lens 3MP Zoom Bullet with D N Adaptive IR Superior WDR 12x Zoom lens 3MP Zoom Bullet with D N Adaptive IR Superior WDR 10x Zoom lens 10MP Zoom Bullet with D N Adaptive IR Basic WDR 10x Zoom lens 1MP Zoom Bullet with D N Adaptive IR Extreme WDR ELLS 30x Zoom lens 2MP Zoom Bullet with D N Adaptive IR Extreme WDR ELLS 30x Zoom lens 4MP Zoom Bullet with D N Adaptive IR Advanced WDR SLLS 30x Zoom lens From the installation perspective these models are very similar therefore you can use one manual for all of them www acti com ACTI Connecting Vision DM Hardware Manual Package Contents Camera Sunshield Sunshield Screws Hexagon Screwdriver Camera Base Wrench Bracket Wrench I 7 Female Conduit Gland Female Cable Gland Washer Male Cable Gland Male Conduit Gland Optional Drill Template
31. ower up the camera using a power adapter not supplied As needed power up the other connected devices Step 6 Access Camera Live View See Accessing the Camera on page 46 for more information on how to access the camera live view 8 ACTI Connecting Vision DM Hardware Manual Step 7 Adjust the Viewing Angle Based on the camera live view adjust the camera viewing angle Do the following Tilt Adjustment Screw L Pan Adjustment Screw Using the bundled bracket wrench do the following 1 Loosen the tilt adjustment screws adjust the camera tilt and then tighten back the screws to fix the tilt position 2 Loosen the pan adjustment screw move the pan direction and then tighten back the screw to fix the pan position www acti Com pq ACTI Connecting Vision Hardware Manual Waterproof Solution Using the Pigtail The camera and the pre installed network cable pigtail are resistant to salt water weak acid alcohol oil grease and other common solvents However users must ensure that the cable connection and the network side cable itself are also protected from different environmental factors When using a Power over Ethernet PoE switch or injector connecting the network cable through the pigtail is recommended In this case there are two waterproofing methods Bundled Accessory Description Female Cable Gland Use t
32. p 7 Adjust the Viewing Angle cc sccssseecsseeceneeceneeceneeceneeseneees 17 Waterproof Solution Using the Pigtail 18 How to Use the Female Cable Gland c ccccesseeesseeeeseeeeneeeeneseaees 19 How to Use the Female Conduit Gland ccssesesseeeeseeeeseeeeneseeees 22 Waterproof Solution Using the Camera CONECTO aces ga a gata eaaa E 26 How to Use the Male Cable Gland Optional ccsceseeeeeeeeeees 28 How to Use the Male Conduit Gland ccccceesseeeeeeeeneeeeseeeeeeeeeeeenaes 32 Other CONNECTIONS ccceecsecseceeeeeneenseeseeseenseeaes 36 Connecting a Power Adapter Optional ccsseecesseeeseeceneeeeneees 36 2 www acti com pq ACTI Connecting Vision Hardware Manual Connecting DI DO and Audio Devices Optional sseceeeeees 38 How to Connect DI DO DevIcas sasana mrasani na wana na ua ga aaa ua waga wawa ajana ea a 38 How to Connect Audio DeVICES ccccceeccceeceeeeeeseeeeeeeeeseeeesaeeeseeeesees 41 Other Adjustments and Accessories 42 HOW TO Remove the Pigtall sasabana aa aa wa daana a a aaa aaa aa aaa ana aaa aa aaa 42 How to Insert a Memory Card aasasenanenenennnnennneananananenennanananennnnananenane 45 How to Insert the Memory Card ccccceecccseeceeeeeeesseeeesseeeesaaeeesaeeeeas 45 How to Remove the Memory Card ccc
33. ser Required Plug In Safari QuickTime http Awww apple com quicktime download Other non Internet Explorer Basic VLC Media Player htto www videolan org browsers Disclaimer Notice The camera manufacturer does not guarantee the compatibility of its cameras with VLC player or QuickTime since these are third party softwares The third party has the right to modify their utility any time which might affect the compatibility In such cases please use Internet Explorer browser instead When using Internet Explorer browser the ActiveX control for video stream management will be downloaded from the camera directly the user just has to accept the use of such control when prompted so No other third party utilities are required to be installed in such case The examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera so DM ACTI Connecting Vision Hardware Manual Assuming that the camera s IP address is 192 168 0 100 you can access it by opening the Web browser and typing the following address into Web browser s address bar http 192 168 0 100 Upon successful connection to the camera the user interface called Web Configurator would appear together with the login page The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80 which can be omitted from the address for convenience ae Web Config
34. sunshield 2 Slide to adjust the sunshield to cover the lens as far as possible NOTE The sunshield may have to be adjusted later based on the camera live view 3 Tighten the screws to secure the sunshield a ACTI Connecting Vision DM Hardware Manual Step 3 Install the Camera 1 If the pigtail will pass through the wall follow Waterproof Solution Using the Pigtail on page 18 first and then route the cable through the wall If the pigtail will go along the wall route the cable through one of the cable gaps on the bracket 2 Install the camera to the wall using four 4 screws applicable for the wall material purchased separately NOTE Make sure the wall can bear more than the weight of the camera with bracket Step 4 Waterproof and Connect the Network Cable See Waterproof Solution Using the Pigtail on page 18 9 MI ACTi gt Connecting Vision Hardware Manual Step 5 Connect to Network Connect the other end of the network cable to a switch or injector Then connect the switch or injector to a network or PC and a power source See Power over Ethernet PoE example connection diagram below Ethernet Cable Ethernet Cable Data PoE Injector Power Cable PoE Switch Ethernet Cable Data Power AC Power Source cole ani Camera In case of using a non PoE switch p
35. urator x Web Configurator Account Password Language English v Login Reset Before logging in you need to know the factory default Account and Password of the camera Account Admin Password 123456 For further operations please refer to the Firmware User Manual 4 Connecting Vision Copyright 2015 ACTi Corporation All Rights Reserved 7F No 1 Alley 20 Lane 407 Sec 2 Ti Ding Blvd Neihu District Taipei Taiwan 114 R O C TEL 886 2 2656 2588 FAX 886 2 2656 2599 Email sales acti com
Download Pdf Manuals
Related Search