ALFA144GH Operation Manual
Contents
1. 50 mm 462. Use a 5 x 1 5 mm five core cable 43 Fixed connection Fit the power line with an omnipolar circuit breaker in compliance with installation regulations The circuit breaker should be located near the appliance and in an easily reachable position Connection with plug and socket Make sure that the plug and socket are of the same type Avoid using adapters and shunts as these could cause overheating and a risk of burns Cable replacement 1 Unscrew the rear casing screws and remove the casing to access the terminal board Replace the cable NO Make sure that the cables follow the best route in order to avoid any contact with the appliance OO 5 2 Water connection Connect the water inlet socket on the back of the appliance to a water socket with a threaded 34 opening SIAC SSS 5 3 Positioning Steam outlet pipe Depending on the model there are two exhaust flues on the back of the appliance tor releasing the steam produced during cooking Levelling Level the appliance on the ground using the adjustable feet The toot has a range of 10 mm LLJ Distances Place the appliance at a distance of at least 50 mm trom any back wall and at 30 mm trom any side wall Keep a minimum distance of 50 mm between the appliances in the case of installation of multiple and adjacent appliances
3. f symbols to set the temperature Press the knob the display will show the cooking start time flashing Turn the knob to f symbols to set the preheating start time 10 Press the knob the display will show the minutes flashing Use J 1 1 Turn the knob to H symbols to set Rapid cooling the minutes The oven is equipped with a 12 Press the knob to exit from the data special function that allows the setting and saving phase The text oven interior to be cooled rapidly LLJ ruinm appears on the display and at the end of cooking atter 3 seconds it will display P39 the temperature and the preheating start time From the OFF status open the door and hold JART down for at least 4 seconds This will activate the internal 13 To start the program press STAT tor at motor fan the heating elements are least 2 seconds The display will show switched off and the display shows the the current time and P39A in text succession until the program is activated To stop the function press key TOP in succession NO at the set time of A Cleaning and maintenance 4 5 Removing the door For easier cleaning the door can be 4 1 Instructions removed and placed on a canvas To remove the door proceed as follows 1 Open the door completely and insert two pins into the holes on the hinges indicated in the figure 2 Grasp the door on b
4. to set the cooking temperature NO OO 4 Press the knob the display will show the cooking time 5 Turn the knob to f to set the cooking time from to 99 minutes On the basic model 6 Press the knob to exit from the data setting and saving phase The message PE nmd RA appear on the display and the parameters will be saved 7 After 3 seconds the display will show the parameters set in rotation 8 To return to the OFF status hold TOP down for 4 seconds On the model with humidification 6 Press the program selection knob the display will show the level of humiditication 7 Turn the program selection knob to f to set the level of humidification HO H1 Set HO if oven humidification is not required If the temperature is set below 110 C no oven humidification level can be set 2 8 Press the knob the display will show the duration of the grilling to be performed at the end of cooking 9 Turn the program selection knob to e z to setthe time from 1 to 99 minutes fmm Set O if no grilling is required at the end of cooking The grilling time is additional to the time set for normal cooking 10 Press the knob to exit from the data setting and saving phase The message ai feted will appear on the display and the parameters will be saved 11 Atter 3 seconds the display will show the parameters set in rotation 12 To return t
5. cooking hold button START down for 2 seconds The display will show the set cooking parameters in sequence Iltis possible to start cooking early before the preheating temperature is reached by holding START down tor 3 seconds The operating parameters can be moditied during cooking as indicated in paragraph Moditying a program during cooking During the last minute of cooking only the countdown of the remaining 60 seconds will be displayed At the end a beep and the text flashing for 36 Use 20 minutes will indicate that cooking has been completed 8 At the end of cooking End flashes 9 on the display and the buzzer sounds intermittently To carry out the same program press START again The text will appear on the display Turn the knob to to set up to a maximum of 20 additional minutes To return to the OFF status hold QP down for 4 seconds The parameters set tor the program are deleted Preheating with delayed start NO OO CO Turn the knob to H to select program P39 Press the knob for at least 3 seconds the display shows the current time flashing Turn the knob to symbols to set the cooking start time Press the knob the display will show the minutes flashing Turn the knob to symbols to set the minutes Press the knob the display will show the temperature flashing Turn the knob to
6. cooking has resumed 4 At the end of cooking the text will continue to flash for the next 20 minutes and the oven light will remain on The fan keeps turning until 910P is pressed Modifying a program during cooking During cooking you can modify the parameters set for the program Changes made to the program during cooking are not saved 1 Press the knob the display will show the cooking temperature 2 Modify the settings as described in Editing saving a thermo ventilated program or Editing saving a grill program 3 3 seconds after the last change the program automatically quits the modification status and saves the settings the modified parameters are saved solely until the end of cooking so LLJ 2 Manual cooking The manual program P40 that can be edited by the user does OO not save the set cooking parameters Save the program temporarily as described in paragraph Editing saving a thermo ventilated program Unlike saved programs the cooking time can be set to infinite AF After saving it do NOT return to the OFF status Press START the appliance will perform a preheating cycle showing the text PFE on the display When preheating is finished a series of beeps lasting 3 seconds will indicate that it is possible to proceed with the cooking operation The text PAA will flash on the display To start
7. Contents 1 Instructions 26 1 1 How to read the user manual 26 1 2 This user manual 26 1 3 Appliance purpose 26 1 4 General safety instructions 26 1 5 Manufacturer liability 27 1 6 Identification plate 27 1 7 Disposal 27 2 Description 28 2 1 General Description 28 2 2 Control panel 29 2 3 Other parts 29 3 Use 30 3 1 Instructions 30 3 2 First use 31 3 3 Using the oven 32 A Cleaning and maintenance 38 4 1 Instructions 38 4 2 Cleaning the surfaces 38 4 3 Ordinary daily cleaning 38 4 4 Food stains or residues 38 4 5 Removing the door 38 4 6 Cleaning the door glazing 39 4 7 Removing the internal glass panels 39 4 8 Cleaning the inside of the oven 40 4 9 Extraordinary maintenance 41 4 10 Ifthe appliance is not working properly 42 5 Installation 43 5 1 Electrical connection 43 5 2 Water connection 44 5 3 Positioning A5 We advise you to read this manual caretully which contains all the instructions for maintaining the appliance s aesthetic and functional qualities For further information on the product www smegfoodservice com 23 A 1 Instructions 1 1 How to read the user manual This user manual uses the following reading conventions Instructions General information on this user manual on safety and final disposal gt Description Description of the appliance and its accessories Use SW information on the use of the 3 appliance and its accessories cooking advice Pi Li Cleaning an
8. It is possible to start cooking early before the preheating temperature is reached by holding START down for 3 seconds 5 During the last minute of cooking only the countdown of the remaining 60 seconds will be displayed At the end a beep and the text flashing for 20 minutes will indicate that cooking has been completed 6 To return to the OFF status hold 670P down for 4 seconds Use Running a grill program From the OFF status Turn the knob to f to select one of the grill programs The display will show the parameters of the selected program in rotation Press START the appliance will start the grill cooking cycle and the display will show the time remaining in minutes preceded by the tlashing text During the last minute of cooking il only the countdown of the remaining 6O seconds will be displayed NO 3 At the end a beep and the text flashing for 20 minutes will indicate that cooking has been completed Extending a cooking operation When a cooking operation finishes it is possible to extend it manually 1 While the display is showing the text End press STAB the text SIRER will appear on the display 2 Turn the knob to f to set the additional minutes of cooking At most 20 extra minutes are allowed 3 To start cooking with the extra time that has just been set press STAPT for at least 2 seconds A beep will indicate that
9. anel Basic model Model with grill heating element and humidification system START button 1 It starts cooking or a rapid cooling cycle atter cooking is completed On the model with humidification it also starts the manual humiditication cycle STOP button 2 It ends cooking at any time Display 3 It displays the selected program and the relevant cooking parameters Program selection knob 4 It allows you to select the cooking program and modify the set parameters such as temperature and time 2 3 Other parts Shelves The appliance features shelves for positioning trays and racks at different heights The insertion heights are indicated trom the bottom upwards see 2 1 General Description Internal ventilation The counter rotating tans deactivate automatically when the door is opened and resume operation when the door is closed Interior lighting The oven interior lighting comes on when the door depending on the modell is opened or any function is selected Safety thermostat The appliance is equipped with a safety device that triggers in case of serious malfunction To re arm the safety device press the button on the back Vy Contact technical support LS immediately atter the safety device has triggered to check if there are any faults 29 ix 3 3 Use 3 1 Instructions 3 2 First use 1 K Remove any protective film trom the outside o
10. d maintenance Information for proper cleaning and maintenance of the appliance Installation Information for the qualified xX technician installation operation and inspection Safety instructions Information Advice IN ES Use instruction sequence e Single use instruction 20 Instructions 1 2 This user manual This user manual is an integral part of the appliance and must therefore be kept in its entirety and in an accessible place for the whole working lite of the appliance 1 3 Appliance purpose This appliance is intended for cooking food in the protessional environment Every other use is considered improper This appliance must not be used by people including children of reduced physical and mental capacity or lacking in experience in the use of electrical appliances unless they are supervised or instructed by adults who are responsible for their safety 1 4 General safety instructions For your satety and to avoid damage to the appliance always respect the general satety instructions indicated below In general e Have qualified personnel carry out installation and assistance interventions according to the standards in force e Read this user manual carefully before using the appliance e Do not modify this appliance e Do not try to repair the appliance yourselt or without the intervention of a qualitied technician e Ifthe power supply cable is damaged contact tech
11. e procedures to put the guide trames back in Cleaning and maintenance Wil 4 9 Extraordinary maintenance 6 Replace the cover correctly so that the moulded part of the glass is facing the i Live parts disap Danger of electrocution 7 Press the cover completely down so that Lu it attaches pertectly to the bulb support e Disconnect the oven power supply Removing the door seal To permit thorough cleaning of the oven the door seal may be removed There are l Completely remove all accessories from fasteners on all four sides and in the middle inside the oven to attach it to the edge of the oven Pull the edges of the seal outwards where indicated to detach it Replacing the internal light bulb 2 Remove the racks trays support frames 3 Remove the bulb cover using a tool e g a screwdriver Ai Incandescent lamps 4 Unscrew and remove the lamp 5 Replace the lamp with one of the same type 25VV 4 10 If the appliance is not working properly The oven is not working oods either take too long or too little to cook No steam is being supplied Moisture forms inside the oven and on the foods There is water inside the oven This product meets the current satety regulations in force for electrical appliances To prevent safety hazards for users all technical inspections o
12. nical support immediately and they will replace it Instructions A For this appliance e Do not obstruct ventilation openings and heat dispersal slots e Do not insert pointed metal objects cutlery or utensils into the slots in the appliance e Do not rest any weight or sit on the open door of the appliance e Take care that no objects are stuck in the doors e Do not use the appliance to heat rooms for any reason 1 5 Manufacturer liability The manufacturer declines all liability tor damage to persons or property caused by e use of the appliance other than the one envisaged e non observance of the user manual provisions e tampering with any part of the appliance e use of non original spare parts 1 6 Identification plate The identitication plate bears the technical data serial number and brand name of the appliance Do not remove the identitication plate for any reason 1 7 Disposal This appliance must be disposed of separately trom other waste Directives 2002 95 EC 2002 96 EC 2003 108 EC The appliance does not contain substances in quantities sufficient to be considered hazardous to health and the environment in accordance with current European directives To dispose of the appliance e Cut the power supply cable and remove Remove the doors and leave the accessories racks and trays in their usual working positions so that children cannot get stuck in the oven compartment i
13. o the OFF status hold QP down for 4 seconds 33 Editing saving a grill program 1 Turn the knob to H to select the program you wish to save or edit 2 Hold the knob down for 3 seconds the display will show the cooking time 3 Turn the knob to f to set the cooking time from 1 to 30 minutes 4 Press the knob to exit trom the data setting and saving phase The message aF feta will appear on the display and the parameters will be saved The grill function is set at a grilling il temperature of approximately 290 C This temperature cannot be changed by the user Grilling can only take place with il the oven door closed opening the door deactivates the heating elements 34 Use Running a thermo ventilated program From the OFF status 1 Turn the knob to to select one of the thermo ventilated programs The display will show the parameters of the selected program in rotation 2 Press button START the appliance will perform a preheating cycle the text will appear on the display 3 When preheating is finished a series of beeps lasting 3 seconds will indicate that it is possible to proceed with the cooking operation The text PARESE will flash on the display 4 To start cooking hold button START down tor 2 seconds The display will show the set parameters in sequence with the time remaining until the end of cooking and the program selected
14. oth sides with both hands litt it forming an angle of around 30 and remove it 4 2 Cleaning the surfaces To keep the surtaces in good condition they should be cleaned regularly after use Let them cool first 4 3 Ordinary daily cleaning Always use only specitic products that do not contain abrasives or chlorine based acids Pour the product onto a damp cloth and 3 To reassemble the door put the hinges in wipe the surtace rinse thoroughly and dry the relevant slots in the oven making sure with a soft cloth or a microfibre cloth that grooved sections A are resting 4 4 Food stains or residues completely in the slots Lower the door Do not use metallic soonges or sharp scrapers as they will damage the surfaces Use ordinary non abrasive products with the aid of wooden or plastic utensils if necessary Rinse thoroughly and dry with a soft cloth or a microfibre cloth 38 Cleaning and maintenance Wil and once it is in place remove the pins trom the holes in the hinges 4 6 Cleaning the door glazing The glass in the door should always be kept thoroughly clean Use absorbent kitchen roll In case of stubborn dirt wash with a damp sponge and an ordinary detergent a We recommend the use of cleaning products distributed by the manufacturer 4 7 Removing the internal glass panels For easier cleaning the door internal gla
15. r inside of the appliance including accessories Remove any labels apart from the technical data plate trom the accessories and from the cooking compartment Remove and wash all the appliance accessories if fitted see 4 Cleaning and maintenance Heat the empty oven at the maximum temperature to burn off any residues lett by the manufacturing process Setting the power The maximum absorbed power value will be displayed flashing after connecting the appliance to the power supply 1 Turn the knob to to select the maximum absorbed power 2 Press the knob to confirm the selection 3 3 3 Using the oven Humidification option on some models only For thermo ventilated functions except for P39 you can set 3 different humidification levels Each level has a pause time between an humidification cycle and the next Choice of programs This appliance allows you to select 40 cooking programs including e 38 programs that can be edited and saved as the user wishes To humidify the cavity manually during e preheating program with delayed start l D30 cooking hold START down e manual program PAO Use Editing saving a thermo ventilated program Turn the knob to H to select the program you wish to save or edit Hold the knob down for 3 seconds the display will show the cooking temperature set for the program Turn the knob to e
16. r repairs must be carried out by qualitied personnel 42 e timer knob is positioned on The plug is not properly inserted in the socket The electrical system is damaged or not working properly The fuses have blown or the circuit breakers have not been activated e temperature setting is incorrect e humiaitication program has not been set properly The oven door has not been closed properly e fooas are being leit in tne oven tor too long after cooking Do not leave them in the oven for more than 15 20 minutes after the end of the cooking time e device controlling tne supply of water inside the oven is not working properly The dispensing command has been activated for too long 5 Installation 5 1 Electrical connection General information Check the grid characteristics against the data indicated on the plate The identitication plate bearing the technical data serial number and brand name is visibly positioned on the appliance Do not remove this plate for any reason Perform the ground connection using a wire that is 20 mm longer than the other wires The appliance is equipped with a tive core HO 7RN F cable 5 x 1 5 mm2 referring to the cross section of the internal conductor Connection modes e 220 240 V IN L1 N Use a 3 x 4 mm three core cable e 380 415 V 2N 123 4 5 L1 L2 IN Use a 4 x 2 5 mm four core cable e 380 415 V 3N 1 2 3 4 5 Tele
17. ss panels can be disassembled l Remove the internal glass panel by pulling the rear part gently upwards following the movement indicated by the arrows 1 2 Then pull the front part upwards 2 In this way the 4 pins attached to the glass detach trom their housings in the oven door Clean the external glass panel and the panels previously removed Use absorbent kitchen roll In case of stubborn dirt wash with a damp sponge and neutral detergent Reposition the internal glass panel Take care to centre and insert the 4 pins into their housings in the oven door by applying slight pressure 39 4 8 Cleaning the inside of the oven For the best oven upkeep clean it regularly atter having allowed it to cool P The oven should be operated at the maximum temperature for _ about 15 20 minutes after the use of specitic products to burn off the residues lett inside the oven For easier cleaning remove the eae oor Removing racks trays support frames Removing the guide frames enables the sides to be cleaned more easily unscrew the fastening pins of the trame AO Cleaning and maintenance To remove the guide trames pull the frame upwards to unhook it from its groove then slide it out of the seats at the back When cleaning is complete repeat the abov
18. t along with the plug Power voltage Danger of electrocution e Disconnect the main power supply e Disconnect the power cable trom the electrical system Consign the appliance to the appropriate selective collection centres tor electrical and electronic equipment waste or deliver it back to the retailer when purchasing an equivalent product on a one for one basis Our appliances are packed in non polluting and recyclable materials e Consign the packing materials to the appropriate selective collection centres Plastic packaging Danger of suffocation e Do not leave the packaging or any part of it unattended e Do not let children play with the packaging plastic bags ar Description 2 Description 2 1 General Description 3 Model with grill heating element and humidification system 1 Control panel 6 Rack tray support frames 2 Oven light 7 Steam inlet pipe 3 Seal 8 Grill heating element 4 Door 12 3 Frame shelf 5 Oven fan 28 Description 2 2 Control p
Download Pdf Manuals
Related Search