fastrack ii helmet manual
Contents
1. 4 RIDER Accept the pairing Turn the MFB clockwise on the RIDER Bluetooth Helmet until the blue and red indicator lights flash Then release it Helmets are now ready for intercom use 5 To Make an Intercom Call Since both Driver and Passenger are in pairing mode intercom connection will be established between them automatically and both side will hear 3 pulsing ringtones in speaker Once you are connected you will be able to communicate without needing to touch the button again If the helmets get out of range about 30 feet you may lose the connection As soon as the helmets are back in range they will automatically be reconnected and voice communication will be restored 6 To Disconnect an intercom session Press the MFB once second on either of the two helmets Note You can not make a call while in intercom mode In order to make a call you must first disconnect from intercom and reconnect to your bluetooth device BLUETOOTH INTEGRATED COMMUNICATION Listening to music First pair your helmet with the Bluetooth device mp3 radio etc in the same way that you paired it with your mobile phone Your BLINC equipped helmet allows you to listen to music from your Bluetooth streaming music source If listening to music from your mobile phone when placing or receiving calls music playing from the mobile phone is automatically paused When the call is finished music playing is resumed If th2. Charging Port Cover Charging Plug 7 BLINC BLUETOOTH INTEGRATED COMMUNICATION Blinc Bluetooth Headset Control Unit Turning the BLINC Headset OFF VOL Volume Decrease ae INC MFB Multi Function Button Press and hold the Multi Function Button MFB for approximately 5 seconds until you hear a short high tone counter clockwise aa ETODOTH The BLINC headset indicator light will switch off in 3 4 seconds after you hear the tone VOL Volume Increase turn clockwise Adjusting the Volume Red Indicator Light Blue Indicator Light This BLINC headset has a volume control dial VOL and VOL the MFB is in the center of it You can adjust the BLINC headset speaker volume by turning the dial during a call or adjust the ring volume when you are not engaged in a call Press and hold the Multi Function When turned on the BLINC Button MFB for approximately 2 4 m IN headset automatically establishes Volume Decrease Volume Increase UETOOTH counter clockwise gt turn clockwise seconds until you hear a short high BLH 027 hands free phone and streaming tone if your helmet is off put your music connections with the last ear close to the speaker in the left connected Bluetooth devices side of the helmet to hear it The BLINC headset indicator light flashes blue phone and or music device BLUETOOTH INTEGRATED COMMUNIC
3. amp 7 COINS Te BLUETOOTH USER MANUAL O Neal Distributing Inc 685 Cochran St Simi Valley 93065 USA WWw oneal com www oneal com support Made in China 5 535 ED J TO RIDER WIRELESS BLUETOOTH STREAMING MUSIC GPS SYNC BLINC IS PATENT PENDING AND A REGISTERED TRADEMARK USED UNDER LICENSE BY O NEAL BLINC Bluetooth Introduction The BLINC integrated helmet communications system is based on Bluetooth wireless technology Bluetooth wireless technology is a short range radio communication technology intended to replace the cables connecting electronic devices The technology uses a globally available frequency range intended to ensure communication compatibility worldwide You can connect your BLINC equipped helmet to your mobile phone or any device with Bluetooth wireless technology that supports the BLINC Headset profile or the Hands free profile When the BLINC system is connected to your mobile phone you can handle incoming and outgoing calls listen to music or GPS instructions and adjust the volume using the controls on the BLINC equipped helmet It can connect to mobile phones music players and GPS systems that are Bluetooth enabled It will also operate as an intercom with another BLINC equipped helmet The BLINC Bluetooth headset system is completely built in to the helmet and consists of a microphone earphone glove friendly controls and a batt
4. JTEGHATED DAIL BLUETOOTH INTEGRATED COMMUNICATION How to use BLINC with your mobile phone I To answer a call When the BLINC headset rings press the Multi Function Button MFB on the helmet control unit to answer the incoming call 2 To terminate a call Press the Multi Function Button MFB on the helmet control unit to terminate call 3 To reject a call When the headset rings press and hold the Multi Function Button MFB on the helmet control for about 3 seconds and release the MFB to reject an incoming call Note this function is valid only if your phone supports Hands Free Profile 4 Last Number Redial When the headset is idle double click the Multi Function Button MFB to redial the last called phone number 5 To use Voice Commands f the BLINC headset is idle press and hold the Multi Function Button MFB on the helmet control unit for 3 seconds then release you will now be able to use voice commands to make calls Note This function is only valid if your phone supports voice commands 6 To transfer the sound back to your mobile phone During a call using your headset press the Multi Function Button MFB for approximately 2 Seconds If your headset works with Head Set Profile you just need turn off your headset Note If the Multi Function Button MFB is pressed too long the call will end 7 To transfer sound from mobile phone to BLINC headset If you make a call using
5. connection with the sale of this product Some jurisdictions do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction E inf ti isit or more inrormation visi oneal com BLUETOOTH INTEGRATED COMMUNICATION
6. your phone you can transfer the sound to the BLINC headset by pressing the Multi Function Button MFB when the BLINC system is in the off position or follow menu on your phone 8 Taking a phone call while in intercom mode While speaking through the intercom function to another helmet When the call arrives the intercom will disconnect autmatically then you can press the Multi function MFB to answer the phone call Note Not all phone brands may apply if you can not hear the incoming call you need set your mobile phone on the vibrate mode and position it so that you will feel it vibrate When the call arrives press the Multi Function MFB on the helmet control unit once to end the intercom connection they press it again to answer the phone call gt gt gt BLUETOOTH INTEGRATED COMMUNICATION Pairing helmets for BLINC intercom Before pairing make sure there is no Bluetooth device active in your area 2 Turn on the RIDER Bluetooth Press and hold the Multi Function Button MFB for 3 4 seconds on RIDER Bluetooth Helmet Release the button as soon as the Blue light flashes Blue only RIDER N e gt gLUETOOTH 3 PASSENGER Seeking mode From the off position Press and hold the MFB on PASSENGER Bluetooth Helmet FOR 6 7 seconds until the blue AND red indicator lights start blinking Release the MFB after the blue and red lights begin to flash PASSENGER BLING
7. ATION Push MFB Here MFB Multi Function Button pair the BLINC headset with a phone or another device On the phone or other device enter the search for Bluetooth device mode 2 Starting with the BLINC headset in the OFF position press and hold the Multi Function Button MFB on the helmet control unit for approximately 6 8 seconds until the blue and red indicator lights flash alternately 3 On your phone or Bluetooth device select Add new device or Helmet_Intercom_Over to connect to BLINC 4 If prompted the Password PIN is 0000 5 If pairing is successful the BLINC headset indicator blue light flashes slowly and red indicator light will turn off 6 Pairing should need to be done only once Each time you turn on your BLINC system it should automatically connect to your phone or other device Note Before entering pairing mode please make sure other nearby Bluetooth devices are switched off BLINC Password PIN is 0000 Phone Set up Pairing Tips Before selecting Add new device on your phone you need to press and hold the MFB on the BLINC control unit until the blue and red indicator lights start blinking 2 Click Add new device or select Helmet_Intercom_Over on your phone 3 If prompted enter Password PIN 0000 Note Follow any further instructions per your phone s owner s manual Oo aa BLING BLUETOOTH PRD r 4
8. battery to slide into position Replace the cover Figure 4 If you need to replace the battery turn off the BLINC Bluetooth headset first and follow the directions above Charging Port Hold the battery handle to pull out the battery If battery is difficult to remove use flat head screwdriver as leverage and 46 place tip under battery handle to gently pry out Figure 3 4 Inserted Bluetooth Module gt BLUETOOTH INTEGRATED COMMUNICATION Charging We recommend that you fully charge the battery before using the BLINC headset for the first time Connect the charger to the charging port of the battery unit and plug the charger into your wall outlet The charging time is about 5 7 hours During charging the indicator on the BLINC control unit on the left side of the helmet shows a steady red light When the battery is fully charged the red indicator light will switch off When using the BLINC headset if you hear a cadent tone and the indicator red light flashes rhythmically this indicates that the battery needs recharging To charge use the handle on Charging Port cover to gently pull out the cover and turn it about 180 degrees Figure 5 Expose the Charging Port and plug the Charging Plug into the Charging Port Figure 6 If properly connected the indicator light on the Control Unit will turn red when the battery is charging Figure 5 Figure 6 a Charging Port Cover
9. e helmet is paired to the phone when a phone call comes in it will automatically override the music then return to the music mode after the call is terminated Listening to GPS instructions First be sure the headset is switched off Then on the GPS enter the Add Bluetooth device mode Once your GPS is searching for Bluetooth device please press and hold the Multi Function Button MFB on the helmet control unit for approximately 6 seconds until the blue LED and red LED are flashing alternatively Second select helmet_intercom_over from Bluetooth device list on your GPS and input password PIN 0000 at your GPS When BLINC headset is connected with GPS you can hear the navigation prompts NOTE When BLINC headset is connected with GPS it can not be connected with your phone or other devices If you want to answer the dial first you can let your phone be connected with GPS then let GPS be connected with BLINC headset more information for this you can refer to your GPS user manual Bluetooth Interference Issues The quality of Bluetooth transmission may also be affected by the position of your connected device Should you experience choppy or distorted audio move the position of your music device or phone to a different location until the signal improves BLUETOOTH INTEGRATED COMMUNICATION Listening at full volume to music or voice through a BLINC equipped helmet may damage your heari
10. ery module unit To use your BLINC equipped helmet your phone or music device should support the following Bluetooth profile Profile Description HFP Hands free Profile Providing a wireless means for both remote control of the Mobile Phone by the Hands free device and voice connections between the Mobile Phone and the Hands free device Figure Earphone Control Unit gt gt Bluetooth Equipped Helmet Microphone BLUETOOTH INTEGRATED COMMUNICATION Getting Started D To start using your BLINC headset Charging Port Cover Install the BLINC battery if it is not yet installed 2 Charge the BLINC battery Open Direction Figure 2 3 Learn the functions of the control unit 4 Pair the BLINC headset with a device for example a mobile phone Cover Handle Install Replace Battery Sad Bice ush Direction Pull back the helmet liner on the left rear area to expose the battery compartment Figure 1 Push the battery cover Battery Hand Battery handle in the direction of the arrow to remove the cover Figure 2 Once the cover is off you will see the slot where the battery will be installed Slide the battery into the slot until it is flush Figure 3 side of the battery with writing Batere on it should face towards the inside of the helmet the terminals at the bottom and the small handle at the top Figure 3 Pull the helmet liner back to allow the
11. l com or contact us at 800 32 ONEAL or 1 805 426 3300 Proof of warranty coverage i e dated bill of sale is required This Warranty does not apply to any product or part thereof which in the opinion of the Company has suffered or been damaged through alteration improper installation mishandling misuse neglect accident or by removal or defacement of the factory serial number bar code label s The opinion of the Company with respect to this matter shall be final THE EXTENT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES OR LIABILITIES ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY ANY ACTION FORE BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 3 MONTHS FROM THE DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED WHATSOEVER BLING Warranty continued on next page BLUETOOTH BLINC 90 day Limited Warranty continued No person or representative is authorized to assume for the Company any liability other than expressed herein in
12. ng Although the external areas of the helmet are waterproof you are advised to ensure the inside elements of the Bluetooth device are not exposed to water or any other foreign substance Any warranty does not cover the battery and in all cases will be void should it be deemed that the user has caused a malfunction or in any way tampered with the Bluetooth device MANUFACTURER IS NOT LIABLE FOR INJURIES DUE TO MISHANDLING OF THE DEVICE ALWAYS ATTACH AND FASTEN THE HELMET PROPERLY AND RESPECT SPEED LIMITS amp WEATHER WARNINGS FOR SAFETY REASONS THE DEVICE IS PROGRAMMED TO HANDLE CALLS UP TO A SPEED OF 60 MILES PER HOUR ONLY For more information visit oneal com or www oneal com support O Neal 685 Cochran St Simi Valley CA 93065 Toll free 1 800 32 ONEAL Phone 805 426 3300 Fax 1 805 426 3300 BLUETOOTH INTEGRATED COMMUNICATION BLINC 90 day Limited Warranty The Company hereby warrants to the original retail purchaser of this product that should this product or any part thereof under normal use and conditions be proven defective in material or workmanship within 90 days from the date of original purchase such defect s will be repaired or replaced with reconditioned product at the Company s option for parts and repair labor This limited Warranty is the purchaser s exclusive remedy for any such defect s To obtain repairs or replacement within the terms of this warranty please visit www onea
Download Pdf Manuals
Related Search