This is in regards to using a Carlson BRx5 base and rover system
Contents
1. red external power present and in use e Off battery not present e On green battery charge full e On yellow battery charge lt 50 e On red battery charge depleted e Blink battery in use e Off Bluetooth inactive e On blue active Bluetooth connection e Blink blue Bluetooth active and transmitting receiving data e Off SD card not inserted e On yellow SD card inserted not logging data e Blink yellow SD card inserted and reading writing data to SD card e Pulse yellow at 5 Hz SD card inserted and low free space This document contains confidential and proprietary information that remains the property of Carlson Software Inc Page 6 of 6 Updated 12 22 20142. 014 AN Carlson Software Inc www carlsonsw com ar son 102 West 2 4 Street Phone 606 564 5028 e Fax 606 564 6422 Maysville KY 41056 them blank When you have completed tap the Green check X Bases for UNAVCO OST_RTCM3 Delete User Name kn IC h 0 as Password Sa eee reece 15 SurvCE will now connect to the specified NTRIP server and if PUN ee successful SurvCE will download the list of base stations Short id TOST_RTCM3 available from the specified NTRIP server Select the desired me Base ID from the dropdown list Tap the Green Check Position 34 25N 118 84W USA Misc e 16 You should now be back in the GPS Rover menu with the RTK tab highlighted Tap the Green Check to save your settings and to start receiving corrections from the NTRIP caster If the BRx5 is configured as Internal GSM the leftmost LED on the BRx5 will be flashing as each RTK correction data packet is received If the BRx5 is configured as Data Collector Internet then the BT LED will be flashing rapidly as RTK correction data is received from the data collector and the leftmost LED on the control panel will turn Yellow when Float status is achieved and Green when FIXED status is achieved The BRx5 GNSS receiver is now configured as a Network Rover and ready to collect data using SurvCE This document contains confidential and proprietary information that remains the property of Carlson Software Inc Page 5
3. IX Carlson Software Inc www carlsonsw com ar son 102 West 2 4 Street Phone 606 564 5028 Maysville KY 41056 Fax 606 564 6422 Carlson BRx5 GNSS Receiver Network Rover Quick Start Guide This Quick Start Guide outlines the steps to follow using SurvCE SurvPC 4 01 or higher to set up and configure the BRx5 GNSS receiver as network rover using either the BRx5 s internal GSM modem or the data collector for communication with the reference network Install the Batteries amp SIM Card If you are using the BRx5 s internal GSM modem for communication with the reference network you will need to install the GSM SIM card at the same time you install the battery The SIM card is accessible by removing the right hand marked SIM battery tray Before configuring the BRx5 you will need to install the two batteries in the receiver To install a battery 1 Remove the battery tray by squeezing the thumb lever down and with your fingers placed under the lip on the bottom of the battery tray pull the battery tray straight out from Brx5 Some users find it easier to turn the BRx5 upside down and use their fingers to pull the battery tray release lever up while hooking their thumb on the battery tray lip and pulling the tray straight out Thumb lever 2 If there was already a battery installed remove it from the tray 3 Insert the new charged battery into the battery tray a Battery leads making sure the end of the battery wit
4. Internet Select the ISP profile from the drop down list Fe I SP ne Nn nev Nome ol eT Per The entries in this list are the modem connections defined in the Start Programs Setting Connections Connections dialog in the Windows Mobile OS After selecting the desired ISP tap the Green Check 13 Once you have configured the Device you will need to set the parameters for connecting to the reference network Select NTRIP in the Network dropdown The other options are None TCP IP Direct UDP IP Direct and SpiderNet Please reference the SurvCE user manual for instructions on using any of these options Tap the wrenches icon to the right of Network 14 Enter the information required to setup the connection to X MRP Broadcasters the ntrip broadcaster Name is a name you create to A Delete identify the connection the name and all associated data IP Address rtem ntrip org Port 2101 will be available the next time you run SurvCE The IP User Name Password Address is either the URL or the physical IP address of the eea ai ntrip broadcaster The Port typically but not necessarily Operator 2101 is the IP port for the ntrip caster data stream If your 0003000 NTRIP broadcaster requires a User Name and Password for PaE ee eee your account enter them in these fields otherwise leave This document contains confidential and proprietary information that remains the property of Carlson Software Inc Page 4 of 6 Updated 12 22 2
5. confidential and proprietary information that remains the property of Carlson Software Inc Page 3 of 6 Updated 12 22 2014 AN Carlson Software Inc www carlsonsw com ar son 102 West 2 4 Street Phone 606 564 5028 Maysville KY 41056 Fax 606 564 6422 11 For Device Internal GSM tap the wrenches to the right Configure Hemisphere Internal Gsm of the device The Configure Internal GSM window is displayed Use the drop down box to select one of the pre defined cellular providers If your cellular provider is not listed select User Tap the wrenches icon to display Provider Cingular RI and edit the APN Settings Am settings Enter the APN Server Name the APN User Name and the APN Password required for your cellular provider It is important that the correct values are entered in these TRT m fields If the BRx5 is not receiving correction data from the Apn user Name ISPDA CINGULAR COM _ ntrip caster double check and make sure you have the an teens CO correct APN settings for your cellular provider 12 When using Device Data Collector Internet you typically establish the internet connection in the data collector either using WiFi or the data collector s internal cell modem prior to running SurvCE In this case go to step 13 If you are using the data collector s internal cell modem you can Internet Status Disconnected tap the wrenches icon to Configure Data Collector
6. h the leads on top points IT away from the tray as shown below 4 Replace the tray making sure the tray snaps into place Repeat this b process for the other battery tray i When you have removed the right battery tray marked SIM on the front insert the SIM card into the BRx5 as follows 1 Place the BRx5 upside down on its top to get a better view of the card as shown below This document contains confidential and proprietary information that remains the property of Carlson Software Inc Page 1 of 6 Updated 12 22 2014 www carlsonsw com Phone 606 564 5028 Fax 606 564 6422 Carlson Software Inc Car ison 102 West 27d Street Maysville KY 41056 notch end goes in first SD card notch end goes in first Note When you insert either the SIM card or an SD memory card make sure the contacts on the card are facing the top of the unit and the side of the card with the notch goes in first see figure above 2 Place the card in the SIM card slot oriented as shown above 3 Gently push the card in until it clicks 4 Replace the battery and battery tray Powering the BRx5 On and Off Power On Press and hold the Power button until the S320 powers up until you hear one beep Power Off Press and hold the Power button for 3 seconds until you hear three beeps or see the External Power Status LED 4 flash Note When you power on the BRx5 the LEDs go through a heartbeat seque
7. nce during this time the modules power up and the devices initialize Network Rover Setup 1 Power on just the Rover receiver by holding the power button until the lights show on the front then release it GPS Rover 2 Run SurvCE SurvPC 4 01 or higher on your data collector and EZA comms Receiver RTK go into Equip GPS Rover menu selection Manufacturer Carlson Model BRxS i 3 Set the current tab to Manufacturer Carlson and Model BRx5 4 Tap the Comms tab and set it to Type Bluetooth and tap the wrenches icon next to BT Type Windows Mobile This document contains confidential and proprietary information that remains the property of Carlson Software Inc Page 2 of 6 Updated 12 22 2014 z Carlson Software Inc www carlsonsw com i ar son 102 West 2 Street Phone 606 564 5028 Maysville KY 41056 Fax 606 564 6422 5 Tap Find Device and tap on HGPS 320 xxxxxxx xxxxxxx is the serial number of the BRx5 and can be found on the bottom on the receiver if you need to verify it to highlight it and then tap Green Check Multiple Bluetooth ports found Please select which Bluetooth port to use 6 Tap the Green Check again to use Any Available Port Available Port 7 Tap the Bluetooth icon in the top Right to bond to the Rover Bluetooth If this is the first time you have paired the data collector with this BRx5 you will be asked if you want t
8. o add this receiver to your device list Tap Yes to add this receiver to your device list Enter 0000 four zero s for the pass code if prompted only prompted the first time you pair the data collector with the BRx5 Tap Next Tap Done if notified that the BRx5 was successfully added to the device list GPS Rover 8 Tap the Receiver tab and type in 6 5617 feet forthe 2 meter erent comms ae fixed height pole you can also enter 2M for a2 meter height 1Ps Hevss20 JTE 93 7 mm Vertical ight 6 5617 ft z NGS and tap next to Vertical Antenna Height 6 5617 ft O Sant M Elevation Mask Position Rate 3 H2 DGPS Type DGPS Age Limit i Advanced ors rover 9 Tap the RTK tab and set Device to either Current Comms Receiver RT o Internal GSM if you installed a SIM card in the Brx5 Device Data Collector Internet R and want to use the BRx5 s internal GSM modem for Network rrr AR communications with the reference network or RTK Port Data o Data Collector Internet to use your data collector for Message Type Auto M communication with the reference network mrih T R Send Rover Position to Network 10 To configure the selected Device Internal GSM or Data Collector Internet go to step 11 if your Device is Internal GSM otherwise go to step 12 for the Data Collector Internet instructions This document contains
9. of 6 Updated 12 22 2014 Carlson www carlsonsw com Phone 606 564 5028 Fax 606 564 6422 Carlson Software Inc 102 West 2 Street Maysville KY 41056 The BRx5 control panel overview below describes the LED and buttons in the control panel BRx5 Control Panel Overview Diagram A 5 and 6 Item Power button Select button UHF GSM radio GPS position status LED DGPS position status LED External power status LED Battery status LED Bluetooth status LED SD logging status LED Name Description e If unit is Off press and hold until unit powers up until you hear one beep e If unit is On press and hold for 3 seconds until you hear three beeps to power off the unit for Bluetooth UHF GSM SD modules Allows you to review module status or change the status power on off of a module e Off UHF radio or GSM module is OFF or no RTK status LED position computed e On yellow floating point RTK position achieved e On green fixed ambiguity RTK position achieved e Blink green UHF radio or GSM module transmitting receiving data e Pulse red error condition with UHF radio or GSM Module e Off no position e On yellow valid position e Blink yellow operating as a base station and converging on reference coordinates e Off no differential corrections available e On green differentially corrected position computed e Off external power not present e On
Download Pdf Manuals
Related Search