User Manual and Installation Guide for WPWM-88D
Contents
1. USER MANUAL AND INSTALLATION GUIDE PART NAME WPWM 88D This document contains the complete user manual and installation guide for the device WPWM 88D It also contains the connection diagrams that enable the user to employ our retrofit technology without causing damage to the current wiring situations leading to delay or disturbance in the current working environment WHITE PLACARD TECHNOLOGIES PVT LTD www whiteplacard com Technology ang Trust Brief Introduction WPWM 88D PIR Light Switch is a User friendly electronic gadget that can play a vital role in ENERGY SAVING eliminating manual control on application lighting Its sleek and easy to adjust interface helps the user to trim gadget to application suitable output One can adjust ON Time LUX Trip level and sensitivity at the tip of a screw driver for well groomed and dependable performance Features 1 Synchronous with AC230V 50Hz 2 Low power consumption 3 Zero crossing ZC switching 4 Noise rejection circuit 5 Override function for ON manual AUTO Quick check test mode directly from power switch 6 Light sensor to Disable output during daytime 7 Adjustable ON time LUX trip level Sensitivity 8 Auto Reset incase ZC signal disappears 9 Wall Ceiling mount Specifications 1 PIR sensor Dual element 2 Power Supply 230V AC _10 20mA Max 3 Maximum Load 5A 250 VAC 1250VA Max 4 Alarm period 75 seconds to 20 minute 5 Detectable Speed2. 0 5 15 m Sec 6 Mounting Height 2 1 m Typical 7 Detection Range R 88 0 x 18m 8 Adjustable Lux level 1 Lux Daylight 10 EMI RFI Immunity Description Wiring Terminals Wire access holes ON Time Adjust LUX Trip Level Adjust Fixing hole Sensitivity Adjust Copyright White Placard Technologies Pvt Ltd Installation Environmental Precautions Ensure that the following conditions are avoided in site selection 1 Rapid environmental temperature changes 2 Vibrating place 3 In fluid corrosive gases and sea breeze 4 Exposure to direct sunlight or artificial light 5 Exposure to direct wind from heater or air conditioner Pre Installation Checklist Every PIR light switch is fully tested and examined before delivery We recommend checking your piece of PIR light switch for the following 1 The model number of PIR light switch matches the model number you have ordered 2 The model is intact without any damage during shipment Note Do not connect the supply to PIR light switch if there is any sign of damage Contact you supplier in case of any queries regarding the shipment of condition of the model Mounting the Product Mounting the PIR light switch without bracket Skip steps 1 to 4 Wall Ceiling Fixing Screw Ball position Fixing Screw Copyright White Placard Technologies Pvt Ltd Step 1 Release ball position fixing Screws Step 2 Insert ball component in the mounting compo
3. on around 1 5 second after sensing motion across the sensor Unit will enter in Auto mode automatically if it does not sense any motion within 32 seconds Override Mode The term override refers to the change of operating mode by switching the power switch OFF ON twice within three seconds after the warm up period AUTO Mode When working in AUTO mode the load will switch ON after detecting motion across the sensor and remain ON for duration set by NO time potentiometer ON Mode The operating mode can be changed to ON by switching the power switch OFF ON twice within three seconds Load will remain ON continuously if the unit is working in ON mode and is not overridden to AUTO mode it will return to AUTO mode automatically after 8 hours Note Light sensor cannot be overridden by operating modes Adjustable Parameters ON Time When working in Auto mode the load will switch ON after detecting motion across the sensor The ON time of Load can be set from 23 seconds to 4 minutes by adjusting the ON Time Potentiometer from MIN to MAX position the ON time of the Load will get extended until the sensor the motion across it Lux Trip Level The LUX trip level can be adjusted from 2 2500 LUX by varying LUX Level potentiometer in Clockwise direction Sensitivity Sensitivity of the light switch can be adjusted by varying Sensitivity POT if the sensitivity POT is rotated in clock wise direction i e Min to Max the detect
4. ion range covered will be minimum to maximum Note It is recommended to keep the POT at factory calibrated setting Copyright White Placard Technologies Pvt Ltd Wiring Connection L Net N Live EZ m a zZ L Connect the wires to the respective terminals according to the above given instructions Detection Pattern Top view 1 8m 3 7m 88 0 degrees 18m Troubleshooting 1 Unit Load is unfunctional Make sure that a Power and Load connection are Correct b Unit is exposed to LUX level more than the trip level 2 Load is ON continuously a Sensor is sensing the signal continuously b The ON time pot is at MAX position c Environmental conditions are not meet Copyright White Placard Technologies Pvt Ltd
5. nent a Mounting Component o fa i dD y o Ki O 0 Step 3 Mark the mounting hole positing of wall component on the wall and drill the holes Step 4 Mount the well component on wall Note Do not touch the optic Lens as well as the sensor Step 5 Open the front cover by slightly pressing on TOP of the Unit Step 6 Remove the PCB from Unit base by releasing the PCB Fixing Screws O Press here to open the front cover Step 7 Knock out the wire access hole Step 8 Lead wire through the access hole Note Step 9 and 10 will be used for PIR without bracket Step 9 Mark on the mounting hole position and drill the holes Copyright White Placard Technologies Pvt Ltd Step 10 Mount the Unit base firmly on the wall Step 11 Complete the wiring as shown in wiring connection section Step 12 Fix PCB to unit base with the Help of PCB Fixing screws OUD AS Note Step 13 will be used for PIR with Mounting Bracket Step 13 Fix Unit base of the PIR Light switch and Swivel arm of mounting bracket with the screws provided IE il Bracket Mounting Position Step 14 Fix the front cover Step 15 Power on the unit adjust detection zone using the quick check mode Step 16 Tighten the Position screws Copyright White Placard Technologies Pvt Ltd Quick Check Mode The unit will enter in quick check mode if it is switched OFF ON twice within 10 seconds after power ON The Load will remain
Download Pdf Manuals
Related Search