Triax S-HD 207 Digital Satellite Receiver
Contents
1. SCR Sat Channel SCR ID 1 Frequency 1 400 GHz Note Each connected receiver must have an ID number SCR ID and a receiving frequency You can find this informations in the manual of your antenna system or on the wall socket In the line SCR ID choose the ID for your receiver 1 8 using the buttons lt gt Then move the cursor with A or W to Frequency and press the OK button Use the numeric input buttons 1 0 for entering the 4 digit frequency Confirm your inputs by OK Then move the cursor with A or W to Store and press the OK button Please note New programmes found by the channel search will be added to the beginning of the list of stations You can set out the order of stations as you wish and delete programmes you do not want Operating the receiver Operating the receiver Switching receiver ON OFF 1 This receiver is optionally equipped with a low power standby circuit If this function is activated the standby power consumption of the receiver is less than 1W The function is switched ON or OFF in the menu SETTINGS RECEIVER SETUP e Low Power Standby ON Switching on the receiver takes about 10 seconds Display boot e Low Power Standby OFF Receiver switches ON immediately 2 receiver is also equipped with the funcion Auto Standby This function can be activated or deactivated in the menu SETTINGS RECEIVER SETUP If Auto Standby is activated the receiver switches to Stan2. to continue the record Hint Please make sure that the local time of the receiver is set correctly and the video recorder is programmed too Timer Sleep Timer Use A V select line Sleep timer in menu Timer and press OK The following menu appears Sleep Timer 20 07 Switch off time 21 00 o clock Activate Enter Switch off time Activate Line Switch off time with OK Enter the required time by pressing 0 9 Select the line Activate with Activate the programmed timer with lt gt Leave the menus with EXIT 26 Information Information Enter the main menu there use A V to select line nformation and press OK In the upper section of the menu the channel parameters of the activated channel are displayed In the lower section of the menu the signal qualities are displayed Level The further the bar turns right the better the reception C N The further the bar turns right and the higher the dB value the better the signal quality Hint The power of the signal depends on the antenna set up and also on the currently activated channel Please remember this if you want adjust your antenna by controlling the signal power After pressing the 4 gt or the yellow button two further charts with channel software and hardware information are displayed With AW you can change the channel Use EXIT to leave this menu Videotext Press the TEXT button to display the videotex
3. 1 Press for moving the cursor to line satellite There select the satellite you want to scan 4 or gt 2 the cursor to line search mode AW There use lt for selecting the desired search mode Transponder n this mode a certain transponder channel is scanned only Therefore you have to specify this transponder by entering its frequency polarisation and symbol rate Satellite In this mode all stored transponders of the selected satellite are scanned for new channels 3 In line Encrypted you can specify whether you want to search for encrypted channels too No encrypted channels are ignored Yes encrypted channels are searched too 19 Installation The following settings are used only in search mode Transponder 4 Frequency For entering the frequency of the desired transponder please select line Frequency Then press OK and use the numeric input buttons 1 0 for entering the 5 digit frequency Confirm your inputs by OK 5 Polarisation In menu item Polarisation you can set the polarisation vertical or horizontal of the desired transponder by using lt or gt 6 Symbol rate For entering the symbol rate of the desired transponder please select line Symbol rate Then press OK and use the numeric input buttons 1 0 for entering the 5 digit symbol rate Confirm your inputs by OK For starting the Channel search please navigate to line Start scan keys AW and press the OK button on
4. Triax S HD 207 Digital Satellite Receiver Operating Manual 305210 TE a E MEL 4 d S7 V x 4 3 D TRIAX your ultimate connection Content Content COMENT fo 1 1 General instructiors ee eee Y EC Fee EU Te d Ce dua d 3 Safety Instructions eer rtr mre nr 4 52 4 Control elements front and rear 5 Connecting the receiVer erc nere roe hn di epi eer Pen dv ea rtr ens 6 Remote rei Eh rH ne rH e li te ie dan e eve Fo Y ee te Ran evan 7 Initial installatlOrt zu oer repete ee dad en dee ep ee ee ER kr Pea epe eR eR eR aen 8 Operating the Tecelvet x been edere med adimere 10 EPG Electronic Programme Guide ccccccccesceeeceeeseeeeeeeeneceaeeeaeeseaeceaeeeaeeeeeeeeaeeeeeeeeaeenaeees 12 Ik M 12 Settings Receiver setup 13 Settings PIEU n oat aide aide td de de i e a e Wb aan in e ne 14 8 e 15 Settings Sublille 4 5 AN CSN Her 15 Settings OSD Configuration Option 0 0 00 eee eee ee eee eee cee eee 16 Settings
5. Turns Videotext If external mass storage devices are connected P Playback button Fast rewind MENU 0 0 CH 95 0 e gt ARCHIVE Remote control ON OFF button usT Shows list of stations TUR Live Switches between RADIO and TV mode In menu opens confirms or modifies currently selected item e Activates last selected channel Choice of audio channels ED F2 Opens specified menus voL Volume control Opens the information menu cers In menu Delete function MODE No function gt gt Fast forward Opens list of recordings ARCHIVE Record button Transfers EPG date into record timer a Stop button Pause button Setting and managing F2 N of markers Renaming records Initial installation Initial installation After reading the safety instructions see chapter safety instructions and finishing the actions explained in chapter connecting the receiver please use the supplied power cord for connecting the apparatus to the power supply When running the receiver for the first time the welcome menu of the installation guide is displayed at the TV screen It helps you installing the most important settings In the first step of the installation guide please select your Menu language 2 14
6. 18 30 Sports Sports 01 30 54 Newsflash 00 28 10 Rainman 02 10 20 Soccer 00 45 00 Sorting recordings In normal operation press the Archive button to open up the list of recordings Press the LIST button The menu Select list will appear Use the AY buttons to select the sorting criteria and then press OK The list of recordings will be sorted as follows Alphabet The recordings will be put in alphabetical order Date of recording Sorted according to the date of the recording newest recording first Entry Sorted according to where the recording is filed on the mass storage device Recording length Sorted according to the size of the recording Renaming records While a recording is being made it s name will be formed automatically from the broadcast information You can however rename the recordings manually In normal operating press the Archive button The list of recordings appears Use AY to select the programme you would like to rename Then press the blue button This menu will appear Record list 21 06 2010 18 30 Sports 29 In the lower window you will see in the first line the name of the selected programme Below it available characters are shown Use the green button to switch between capital and lower case letters In the name use the red and blue buttons to select the characters you wish to change The current position that can be changed is highlighted in colour Now use the and lt
7. Parental lOCK x nione trn rennen riae ii rne 17 Parental lock device ia 17 Parental Lock changing the PIN ssssssssssssssssseeeeeenee ener nnne nnn nnne nter nnns nnn 17 Installation a DAT Le PER ERE RTL RT 18 Installation antenna 18 installation channel search erret netten renidet 19 Installation Factory EeSOt nione ete t REED UE ed 20 Installation Smartcard Reader 1 21 Installation Software download essent 22 Channel liSt rettet rrr enr reni eee d dne abe d di en a ang 24 Channel list Edit main list etre rite orte eene n e ea e n adag 24 Channel list Edit favourites list nennen 24 Channel list Delete Antenna esent nennen nnn nnne nnne 25 Mu IEEE PE 25 Timer record timer ssscssssssssscsscessresececessesessceoseesesscesssssasecessesacscesssseessceeseseateseseeseaeesees 25 Timer Sleep ee Rae nel e ex e eee e t decns 26 Intonation ani n a reet tei cei re o i eer e 27 Mid amp eotext ne e ro n P D dH Re vy Hoe EY De eec 27 Connection of external mass storage device option 28 List O
8. language by using Aor V Confirm your choice by OK Deutsch English Italiano Suomi Francais Ce amp tina T rkce n Wekome In the second step please select your country Country 1 9 Therefore press A V and then OK If you want to get back to the language selection you have to use the EXIT button Germany Austria NOTE The choice of the country affects the the channel list Switzerland sorting Italy Greece Portugal Hungary Satellite In the third step please select the satellite whose channels Welcome are to be sorted first in the channel list use A or V End the installation with OK Satellite SAT A correction of the previous settings can be carried out by pressing EXIT Astra 19 2 Hot Bird Astra 28 2 Turksat 1C Sirius 4 Initial installation Satellite reception In the last step please select the type of your connected satellite antenna system use or V Standard or SCR Sat Channel Router Satellite Reception Standard SCR Sat Channel Router Standard Choose this option if you want to connect the receiver to a conventional satellite antenna system Move the cursor with A or W to Standard By pressing the OK button all alignments are done automatically SCR Sat Channel Router Choose this option if you want to connect the receiver to a special SCR satellite antenna system Move the cursor with A or W to SCR and press the OK button The following menu is displayed
9. At each on screen display the possible user inputs are explained in the help bar at the lower Screen brink By pressing lt and gt you can change the corresponding settings When leaving a menu EXIT button you will be asked to store the performed modifications Yes or to keep the previous settings No Please choose one of these possibilities by pressing 4 and gt and confirm your choice by OK Turn on the receiver by pressing For entering the main menu please press the MENU button The main menu is displayed Settings Installation Note Mass Storage Device is only displayed when an external Channel list mass storage device is connected at the USB Socket of the Timer receiver Information Mass Storage Device 12 Settings Press the OK button The following menu is displayed Receiver setup Picture Sound Subtitle The first line Receiver Setup is marked OSD configuration Parental lockj Choose this menu item by pressing and confirm by OK Settings Receiver setup The following menu is displayed Receiver setup Time difference Menu language Initial volume HDMI Audio Bitstream Auto Standby Low Power Standby 1 Time difference When operating the receiver for the first time you should set the derivation between your local time and the received GMT time Greenwich Mean Time by pressing lt or gt For Central Europe the following settings are recommended Winter time 1
10. Now a menu with the available audio channels will be shown Use the A buttons to select the audio channel you want to use and press the OK button Pressing the EXIT button to hide the menu again Fast forward and rewind During playback press the Fast Forward button or the Fast Rewind button The symbol B or 4444 will appear and the recording will be played faster in the desired direction Press the Fast Forward or Fast Rewind button again to increase the speed The symbols 4 will appear Press the Fast Forward or Fast Rewind button once more and the speed will be increased to the maximum The symbols or will appear Once you have found the spot you were searching for press the Playback button to return to normal playback operation During fast forward or rewind you can use the lt P buttons to change position within the file This enables you easily to jump over longer sections of film 31 Playback Overview of symbols displayed Indication Meaning Playback Fast forward Very fast forward Maximum speed forward Record Timeshift operation Fast rewind Very fast rewind Maximum speed rewind Operating the hard disk setting and managing markers During the timeshift function or playback you can mark places on the recording A marker is shown as a coloured triangle in the status indicator Press the button F1 at
11. You can resort and or erase TV and radio channels found in the course of an automatic channel search This function is available for all TV and radio channels For entering the corresponding on screen dialog please press the Menu key to enter the Main Menu then select menu item Channel List and confirm with OK Following sub menu appears Channel list Edit main list Edit favourites list Delete antenna Channel list Edit main list This sub menu enables you to erase or move certain channels in the channel list For entering this menu simply enter OK at line Edit main list a Erase channels Select the channel to be erased with A V and mark it with OK You can select more channels by pressing A W and OK To erase them press the red button b Sort channels Select the channel to be sorted by using A V and mark it with OK You can select further channels by pressing A W and OK max 20 channels can be selected at the same time Use A V to select the position where to insert the marked channels and confirm with the yellow button Channel list Edit favourites list This sub menu allows you to add your favourite channels to the favourites list Therefore please press OK in line Edit favourites list Now two lists are displayed the Main list all stored channels are listed max 4000 the favourites list contains your favourite channels max 4000 Now you can select your favourite channels from the Main list and co
12. c by pressing the yellow button For leaving the corresponding on screen graphic use EXIT please 3 starting the update The update download process is started as follows select the desired data pressing OK at a b or c mark changes from amp to select None at menu line Information keys or gt Start the update procedure by pressing OK in line start download You are informed about the download process immediately when the first data are received As the reception of the data happens blockwise several minutes may pass between the single data blocks When the first and second data block are received 100 the data are stored The storage process is signalled by flashing the numbers in the LED display Please wait until all data blocks are received When the update is completed the receiver automatically restarts and turns into Stand By mode Attention As long as the storage process has not begun the download can be cancelled by pressing EXIT at any time When the first data have been stored cancelling is no longer possible An interruption of the update process e g by pulling the power cable may damage the operating software receiver and the receiver does not work any more Hint If the download includes a new channel list the receiver needs to be reset to factory default status for activating this list after download is completed and receiver was restarted 23 Channel list Channel list
13. details about the connected mass storage device Type size etc Use EXIT to leave this window Formatting Allows you to format the mass storage device Formatting the mass storage device will completely delete all data which is recorded on it Afterwards the full recording capacity will again be available In the menu Mass Storage Device move the cursor using the buttons A onto the line Formatting and then press the OK button Recordings 4 of 999 Available space 69699MB EN 3 format No Use lt gt to choose whether you want to format the mass storage device yes or not no After formatting the number of recordings will be reset to zero Available space shows the maximum recording capacity available on the mass storage device Use EXIT to leave the window Caution If you format the mass storage device all recordings on it will be irretrievably lost 28 List of recordings List of recordings In normal operation press the Archive button to open up the list of recordings Deleting recordings You can delete recordings you no longer need from the mass storage device Use A Y to select the recording you wish to delete Then press the red button A security question asking whether you really want to delete the recording will appear Use the lt P buttons to select whether you really want to delete the recording Yes or not No Confirm your choice with the OK button Record list 21 06 2010
14. open or repair the mains adapter or the receiver on your own Service must be carried out only by experts at a proper service centre If replacement parts are required only original components are allowed to use The use of unauthorised components may result in risk of fire and electric shock Cleaning and care Before cleaning unplug the device from the mains adapter For cleaning the casing please use a soft damp cloth Do not use any washing up liquids that affect the casing Do not spray a cleaner towards the receiver PLACEMENT In touch with certain furniture surfaces it may happen that the receiver s feet may rub off You should place the device on a proper underground that is stable and not easily inflammatory Otherwise the receiver may fall and cause serious injury to people and serious damages to the device Do not use this product near water e g bath tube wash bowl Control elements front and rear panel Control elements front and rear panel 1 4 digit display shows channel number 1a or LED Receiver in standby mode Channel number Receiver is ON rEC Timer activated 9 Smartcard reader Digital SAT Receiver 7 8 2 Connector for mains adapter 12VDC 3 TV Scart port for connecting the TV 4 HDMI Output digital Audio and Videosignal for connecting the TV 5 USB socket for external mass storage device 6 IF Input Digital F Connector for antenna cable from LNB Left side 7
15. receiver against unauthorised use When the parental lock is activated the receiver can only be switched on after entering a 4 digit PIN code Parental Lock In the Main menu use the A V buttons to move the cursor to the line Parental lock and press the OK button Device Lock Change PIN Parental lock device lock Use the lt P buttons to switch the device lock on or of When the lock is activated the PIN code must be entered when switching on the receiver To activate or deactivate the device lock move the cursor to the line Device lock and press OK The following menu will appear Press EXIT to leave the menu Use the lt P buttons to choose whether you want to store the changes made Yes or keep the previous settings No Confirm your choice with the OK button Parental Lock changing the PIN To change the PIN code move the cursor to the line Change PIN Change Pin and press OK The following menu will appear New PIN Teste Confirm PIN Use the A V buttons to move the cursor to the line New PIN and press the OK button Use the 0 9 buttons to enter a 4 digit PIN code the press OK Use the button to move the cursor to the line Confirm PIN and press the OK button Now confirm your entry by entering your chosen PIN code one more time then press OK Press Exit to leave the menu Use the lt P buttons to choose whether you want to store the changes made Yes or keep the previou
16. the operating software OSD texts and channel list The result is shown in the Download menu behind the corresponding menu items marked by amp If there are no new data available this is signalled by a You can leave the download menu by EXIT 2 Selection of available data Depending on their availability in the update stream you can select the download of following data by pressing W A a Software Operating software b Channel list Channel list OSD texts All menu texts displayed on the screen d Information Information concerning the available download data e g version number innovations etc 22 If you want to update one of the options a to c press OK at the corresponding menu item If required by the receiver it may happen that there are selected additional menu items automatically In line Information you can specify if you want to receive further information on the selected data keys 4 gt All Information on all available data None Information on none of the available data Software Information on the new software version OSD texts Information on the new menu texts Channel list Information on the new channel list Hint If you like to read these information before doing the update please leave menu items a to C inactive amp and specify the desired information at d Then start downloading these data When received you can view the information at menu items a to
17. the playback position to set a marker You can use the button F2 to show a list of all the markers A recording always has the markers Start and End Using A you can now select a single marker Press the OK button to continue playback at the selected marker When the list of markers is open you can use the button to assign a particular function to a marker so that when playback reaches this marker the function is automatically performed You can assign the following functions to markers Press the button once the marker is interpreted as a loop When the playback reaches a loop marker it jumps to the previous marker A loop marker is labelled L in the list of markers A yellow vertical line is shown in the status indicator Press the button twice the marker becomes a jump marker When the playback reaches a jump marker it jumps to the next marker A jump marker is labelled J in the list of markers A white vertical line is shown in the status indicator Use jump markers e g to jump over commercial breaks Press the button three times this marker has no special function but can be used during playback as place for a loop or jump Press the red button to delete the selected marker from the list The Start and End markers cannot be deleted Press the F2 button or EXIT to close the list 32 gt 00 17 22 Seas 00 20 30 1 00 00 00 Start 2 00 03 11 Mark1 J 3 00 08 58 Mark2 4 00 12 01 Ma
18. 00 hour Summer time 2 00 hours Note This setting has to be updated at each summertime shift 2 Menu language Choose your language by pressing lt gt 3 Initial volume The initial volume after a power reset of the receiver is adjusted here by pressing lt or gt 4 HDMI Audio Bitstream HDMI Audio Bitstream can be switched ON or OFF by pressing lt or gt 5 Auto Standby Auto Standby function can be switched ON or OFF by pressing lt or gt 6 Low Power Standby Low Power Standby function can be switched ON or OFF by pressing lt or gt 13 Settings Settings Picture For entering the Picture menu select menu item Picture in the Settings menu and press OK The following menu appears 1 Analog Video The analog video output at the SCART socket can be adjusted by pressing lt or gt You can Analog Video RGB select among following options FBAS RGB or Digital Video YCbCr YUV Display format 16 9 Display adjustment Letterbox 2 Digital Video Videosystem Auto The digital video output at the HDMI socket can Picture scaling be adjusted by pressing lt gt You can sinput 720x576 Output 1280x720 select among following options YcbCr or RGB Input 1280x720 Output 1280x720 gt Input 1920x1080 Output 1280x720 3 Display format Use 4 or gt for selecting the screen format of your TV set 4 3 16 9 4 Display adjustment Use 4 or gt for adjusting the video signal pan amp s
19. Optical S PDIF interface for DOLBY DIGITAL Signal 8 RJ 11 Socket Connection for an External IR Receiver and Interface for softwareupdate Connecting the receiver Connecting the receiver Connecting a satellite antenna Connect the coaxial cable of your satellite system with the socket IF INPUT DIGITAL 6 Caution If after connecting the receiver to the mains the screen shows the message Short circuit or overload at antenna input there is a short circuit in the LNB cable or in the LNB In this case the receiver must be disconnected from the mains immediately until the short circuit has been remedied Connecting a television Use a scart cable to connect the TV socket 3 on the receiver to the corresponding scart socket on the television set HDMI output 4 If your receiver is connected to the TV by a HDMI cable audio and videosignal are digital Connecting a digital multi channel amplifier The receiver is optionally available with an AUDIO OUT socket 7 for a DOLBY DIGITAL signal Use a suitable cable to connect this socket to your multi channel amplifier Connecting an External IR Receiver optional If you want to set up the receiver where it can t be seen you can connect a external IR receiver to the RJ 11 socket 8 This must be positioned in such a way that it can receive the signals from the remote control When installing the receiver always be sure to follow the safety and installation instructions Con
20. aler Problem Possible causes Help Tips Receiver can not be Power cable not connected to Check if power cord is plugged turned ON mains in correctly Try another electric device at the same power socket Batteries of the remote control are not inserted inserted faulty Check batteries No or bad picture TV set is running on wrong channel Check set up of the TV set Scart cable is damaged or plugged in incorrectly Replace or plug in the Scart cable correctly No audio Remote control does not work Volume is set too low Increase volume Cable damaged or plugged in incorrectly Distance to big Check cable and ports Come closer to receiver point remote control directly towards receiver Batteries are exhausted or inserted incorrectly Insert batteries correctly IR receiver is covered or not reachable by the IR signal Remove barriers between remote control and receiver Timer is activated Deactivate timer Time is displayed Difference between local time Enter menu Receiver setup and wrongfully and GMT is set incorrectly set time difference correctly Timer is activated at the Difference between local time Enter menu Receiver setup and wrong time and GMT is set incorrectly set time difference correctly Channel Change On Screen graphic shows Short circuit or overload at the antenna input Coaxial cable damaged Check coaxial cable and F plu
21. available channel numbers are ignored 3 Using the channel list By pressing the LIST button the last activated channel list or favourite list is displayed Browse the channel list by pressing 4 gt or and activate the desired channel by pressing OK When pressing key LIST twice the following menu appears Favourites list Radio list TV list Alphabetic list Favourites List Your personal list of favourite channels Radio List List of stored Radio channels TV List List of stored TV channels Alphabetic List List of stored TV or RADIO channels in alphabetical order Choose the favoured list by pressing W and activate it by pressing OK In alphabetic list mode the channels are sorted alphabetically It helps you searching a certain channel Therefore press LIST for displaying the alphabetic channel list and its char locator Then enter the char locator menu by pressing Use A V and 4 gt for selecting the first letter of the searched channel and confirm by OK If available the channel list shows the wished channel now For re entering the channel list press for activating the channel use OK 4 Swap from current channel to the previous one Your receiver remembers the previous activated channel By pressing you can switch from the current to the previous channel By pressing again switch back to the current channel Every time you perform a channel change the title and start stop time of the cu
22. can letterbox or pillar box 5 Videosystem Use 4 or gt for adjusting the video system AUTO PAL NTSC 6 Picture scaling Here you can choose the picture resolution 720 x 576 1280 x 720 1920 x 1080 a Television connected to Scart Socket If your TV is only connected to the scart socket of the receiver you get the best picture quality if you choose in the menu item Picture scaling 720x576 for all output signals b Television connected to HDMI Socket If your TV is only connected to the HDMI socket of the receiver you get the best picture quality if you choose in the menu item Picture scaling Input signal Output signal If you prefer fast channel switching all output signals must be the same Press EXIT to leave this menu For storing your modifications select Yes lt or for keeping the previous settings select No Confirm your choice by pressing the OK button 14 Settings Settings Sound Sound settings Stereo Sound channel TV Stereo Sound channel Dig Uncompressed PCM 1 Sound setting Using lt or gt you can activate following audio modes Stereo Mono left or Mono right 2 Sound channel TV If the broadcasted programme offers different audio options you can select the desired audio output at the TV Scart by keys lt gt 3 Sound channel digital If the broadcasted programme offers a digital audio channel you can use lt gt for selecting the audio signal that is to b
23. cess Packaging and wrapping materials as plastic foils etc should never be available for children Safety Instructions Safety Instructions Before installing your digital receiver all security and operating instructions should be read carefully The User s Manual should be retained for future reference All operating and using instructions should be followed Never allow children to operate this electrical device without supervisor ENVIRONMENTAL CONDITIONS Protect the receiver against humidity heat and cold Allow 10cm space around the receiver for sufficient ventilation Do not cover the receiver s ventilation openings with items like newspapers tablecloths curtains etc Do not place any objects filled with liquids such as vases on the digital receiver Take care that no foreign bodies or liquids are getting into the device Do not expose the digital receiver to dripping or splashing liquids CONNECTING TO MAINS SUPPLY SAFETY FEATURE Only connect the original mains adapter to a well reachable mains supply socket 230V 50Hz only Do not tilt do not use disproportionate power and do not damage the receiver s power socket and its electrical connections when connecting the power cord If the mains adapter should fail to fit contact your supplier FAILURE If the mains adapter or the power socket or its electrical connection is damaged immediately unplug the mains adapter from the mains supply socket Do not try to
24. dby Mode after hours running Precondition No timer is activated and no operations with the remote control during this time You can switch on the receiver by pressing OK A V or by using one of the numeric buttons 1 0 The last activated channel will be displayed e g 0015 The digital receiver is switched into standby mode by pressing ATTENTION Only by pulling the mains adapter the receiver is disconnected from the power supply completely TV amp Radio mode You can choose between the operation mode TV viewing TV channels and RADIO listening to radio channels by pressing RADIO Volume control amp Muting The volume level can be adjusted by pressing lt gt or VOL The corresponding scale is displayed on the screen Hint It is not possible to change the volume level while the menu is active The volume control only affects the audio output at the TV VCR and AUDIO ANALOG OUT ports of the receiver By pressing the IK button you can totally switch off the audio output muting For switching on again simply use the same button 10 Operating the receiver Selecting a channel 1 Using the directional up down keys To change the channels stepwise press the buttons A V In order to switch the channels quicker hold these buttons pressed longer 2 Using the numeric keys direct input One or more digit channel numbers can be input by using the numeric buttons 0 9 and pressing OK Not
25. e output at the digital audio port Press EXIT to leave the menu If you want to save your modifications choose Yes for restoring the previous parameters choose No keys lt P gt Confirm your choice by pressing the OK button Settings Subtitle Subtitle Subtitle language 1 Subtitle By using lt you can activate deactivate the display of DVB subtitles if transmitted 2 Language of the subtitle To select the language of the subtitle you must use or gt If there is no subtitle available this is indicated by By default the subtitle is in accordance with the menulanguage Use EXIT to leave the menu If you want to save the modifications choose Yes for restoring the previous parameters choose No keys P Confirm your choice by pressing the OK button 15 Settings Settings OSD Configuration Option For entering the OSD configuration menu please select menu item OSD configuration in the Settings menu and press OK The following menu appears OSD Configuration 1 Display time By using lt or gt you can modify the display duration of the channel change graphics 1 10 seconds Press EXIT to leave this menu If you want to store your modifications select Yes by pressing lt or gt For the restoring the previous settings you have to choose No Confirm your choice by using OK 16 Settings Parental lock Your receiver is equipped with a parental lock This secures the
26. enables you to record and playback at the same time This gives you various options 1 Time delayed television You can watch the beginning of the recording and jump over recorded passages e g commercial breaks Press the red record or PAUSE button to start a timeshift recording To watch the partially recorded programme press the Playback button The programme is then played from the moment of recording while the current programme continues to be recorded in the background If you want to stop the playback and return to normal TV operation press the Stop button To stop a timeshift recording press the Stop button 2 Recordings saved on the mass storage device can be played during timeshift recording During the timeshift recording press the Archive button to open the list of recordings Use AY to select the recording you wish to see Press OK to start the playback The playback information will be shown on the screen If you want to stop the playback and return to normal TV operation press the Stop button To stop a timeshift recording press the Stop button Playback In normal operation press the Archive button to open the list of recordings Use A V to select the recording you wish to see Press OK to start the playback Playback is stopped using the Stop button Choosing the audio channel for recordings When playing back recordings you can choose between the different audio channels During playback press the button Option
27. f reCOrdings oot oad Ee ein ee ives wiv Dev 29 Operating the external mass storage device Option esee 30 Hecordirigis 86 30 Timeshift erae ni NEC EX un 31 Playback eene 31 Choosing the audio channel for recordings Fastforward and t epe oi odi n cee e a 31 Operating the hard disk setting and managing 32 Using serialinterface cnet ree eee bc oae d ede Depas 33 a contribution to environmental protection seessssesssseseeeeeneeeeeeenneen nnns 33 ACA IPTE 34 Technical data oo dete eie ee SRG te hae coated 35 General instructions Warranty The period of warranty starts when buying the device Please verify the exact date by sales check delivery note invoice etc Keep the documents carefully Our warranty service refers to our warranty terms valid at the time of buying the apparatus In case you require technical service please take or send the device to your specialised dealer The unit is labelled with the CE sign and therefore conforms with the general requirements of the European guidelines A Declaration of Conformity is in the later part of this manual Dumping hint for packaging Any packaging material is recyclable and should principally be supplied to the recycling pro
28. g LNB damaged or defective Check or exchange LNB Interference at programmes with a frequency at about Interference may be caused by cellular phones DECT near the receiver Keep more distance between cellular phone and receiver antenna cable 12480 MHz No picture Cable is defect or plugged in Check cable and ports Channel change incorrectly screen graphic shows No valid signal Channel has changed transponder Perform channel search Satellite antenna is not installed correctly Re Adjust satellite antenna Incorrect Settings in menu Settings Correct settings or restore the factory default status 34 Technical data Technical data General 6000 channels e On screen video text and VBI video text Fast OSD e quick channel change zapping e no delay at on screen graphic display big type for better readability e concise help for all menus EPG e Electronic Programme EPG Channel list editor copy replace delete e blockwise operations Channel search e automatic channel search e identification of encrypted channels e manual channel search Display for signal strength and quality e Separate audio output settings for SCART and Digital e SWAP function e DATA interface for updates and channel list transfer updates available via satellite Hardware CPU HDMI Video Audio Handling Power requireme
29. gt buttons to select the character you would like to insert Then press OK to insert the character in the name To accept the new name press EXIT The newly modified name will now be shown in the list of recordings Operating the external mass storage device If an external mass storage device is connected to the USB Socket on the rear side of the receiver you can store recordings on it The recording capacity depends on the size of the mass storage device and the data volume of the broadcast material Recording Various modes of recording area available for you to record programmes onto the mass storage device 1 Immediate recording Switch on the channel you want to record Press the red record button to record the current programme While the recording is running the programme continues to be shown on the screen To stop an immediate recording press the stop button 2 Timer recording You can record programmes onto a connected mass storage device in your absence using the Timer recording function Programme a Time recording as described in the chapter Timer Select the menu item Record on the mass storage device Select a channel during a record During a record all channels in the channel list which are in white colour can be seen Channels which are black cannot be seen during a record The channel which is recorded is marked with a red point in the channel list 30 Timeshift function The Timeshift function
30. herefore please enter the Main menu by pressing Menu then select menu item Timer and confirm with OK Timer record timer Use A V select line Record timer in menu Timer and press OK The following menu appears Record timer Timer index 1 30 1 inactive Start at 00 00 Uhr Stop time 00 00 Uhr Date of recording 01 07 09 Station 1 Das Erste Repetitions nothing Programming a record timer Select line Timer index 1 30 with AW There select timer place with 4 gt Select lines Start at Stop time or date of recording with using and confirm with OK Enter the required time or date by pressing 0 9 Confirm your input with using OK Select line Station with and confirm with OK Select a channel with or lt gt and confirm with 25 8 Select line Repetitions with and use lt P to specify the number of repetitions of this record 9 Select line Activate timer and activate the programmed record timer by pressing OK there text Activate timer changes to Deactivate timer The receiver will switch on at the programmed time and signals a timer record by displaying rEC in the 4 digit LED Display If you want to abort a record please enter the record timer menu and deactivate the timer by pressing the Deactivate button If you push one of the buttons or lt P following menu appears Record active Stop Yes No Choose Yes to stop the record or
31. is connected to a satellite antenna system that receives several satellites multi feed antenna system via a DiSEqC controlled switch unit Specify the input of the DiSEqC switch where the selected LNB line 1 is connected to lt gt 6 Toneburst switch If your receiver is connected to a satellite antenna system that receives two satellites multi feed antenna system Specify the input of the A B Switch where the selected LNB line 1 is connected to lt or gt 18 Installation Installation channel search This digital receiver is pre programmed with most digital TV and RADIO channels of following satellites Astra 19 2 East Hot Bird 13 East T rksat 1C 42 East Sirius 2 3 5 East Amos 1 4 West E Hellas Sat2 39 East If you want to see a list of all programmed channels just open the channel list for TV or RADIO mode by pressing LIST As the broadcasters quite often add new channels to their downlinks or change the parameters of already distributed channels we recommend performing a channel search every now and then For getting into the corresponding on screen dialog please enter the Main Menu key MENU from there step into the nstallation menu select line Channel search and press OK for entering the Channel Search menu Channel search Satellite Astra 19 2 Search mode manually Encrypted No Frequency 12 188GHz Polarisation Horizontal Symbolrate 27 500MS Channel search
32. necting an external mass storage device For recording of TV programmes an external mass storage device can be connected to the optional USB socket 5 Connecting the mains adaptor Connect the DC plug of the mains adaptor supplied with the unit to the socket DC INPUT 12V 2 on the receiver How to insert batteries into the remote control Open the cover at the rear side of the remote control Insert two AAA type batteries 1 5V Attention Take care of appropriate polarity Note If the operational range of the remote control is getting smaller it indicates that the batteries are almost consumed Always replace both batteries Caution Do not heat disassemble or recharge the batteries Consumed batteries are not allowed to be disposed in domestic refuse They must be supplied to a facility collecting and disposing exhausted batteries according to the EU environmental protection rules Remote control x MUTE Sound ON OFF 0 9 Numeric input of channel numbers In Menu Input of numeric parameters frequency etc EPG Displays Electronic Programming Guide EPG 1 Displays Programm Info 4 Volume control In Menu Change parameters or scroll lists AY Channel UP DOWN In Menu selects menu lines Leave current menu or OSD On Screen Display MENU Activates main menu o Channel UP DOWN 9 also in EPG Function
33. nna configuration Select the submenu of the smartcard with A or W and Channel search press OK to confirm Factory reset For more information on using the smartcard see the menus Software download shown or it s instruction manual ov 21 Installation Software download With this function the operating software of the receiver it s menu texts and channel list can be updated via Astra 19 2 East Nevertheless your satellite antenna system must receive this satellite Your currently active channel list is not changed by a software update Attention In case of a software update the current operating software will be erased and a new software version will be installed When updating the channel list the factory default channel list will be replaced by a new one When updating the OSD texts all menu texts are erased and actualised The update process is subdivided into following steps 1 Open Update Menu Enter the Installation menu select line Software download and confirm with OK The Download menu for controlling the update process is opened and the search for the download channel starts automatically Download Software New Software available v Channel list x OSD texts Information Nothing Start Download New Software available Please wait until this search is completed It may take a few minutes When the download stream is found the receiver verifies whether there are available new versions of
34. nt Batteries for remote control Surrounding temperature Dimensions Weight 32 bit RISC CPU e with Upscaler e 1 x SCART with FBAS Y C YUV or RGB support 16 9 signal e Audio DAC e Optical audio out e Volume control e Remote control rare panel control e 12 Volt e Standby mode Low Power Standby ON 1W e 2x1 5V size AAA e 5 to 40 C eBxHxT 230x35 x140 mm Ca 580g Subject to change without prior notice Errors in interpretation excepted 35 TRIAX www triax com 03 2011 A 93 68 EEC Directive and 2004 108 EC repealing 89 336 EEC This product complies with the requirements imposed by the 2006 95 EC repealing the 73 23 EEC Directive amended by the Directive Directives Svend Kristiansen Quality Manager Triax A S Bjernkeervej 3 8783 Hornsyld Danmark Electric and electronic equipment and included batteries contains materials components and substances that can be hazardous to your health and the environment if the waste material discarded electric and electronic equipment and batteries is not handled correctly Electric and electronic equipment and batteries is marked with the crossed out trash can symbol seen below This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other household waste but should be disposed of separately As the end user it is important that you submit your used batterie
35. py them into the favourites list Select the channels you like to add to the favourites list by using and mark them with OK Then press button to enter the favourites list There use A V to select the position where to insert the channel and press OK With you return to the main list again Use EXIT to leave the channel list menu By pressing lt P you can store your modifications Yes or keep the previous settings No Confirm your choice by OK In radio mode you can create your own favourites list for radio programmes too 24 Channel list Delete Antenna This dialog allows you to delete all channels of the selected satellite from the channel list Therefore please enter menu channel list and select menu item Delete Antenna OK Delete Antenna Select the satellites to be erased with W and mark them with OK For erasing their channels from the channel list please press the red button on your remote control For leaving this menu please press EXIT If the Save popup appears please select if you want to store your modifications Yes or keep the previous settings No Confirm your choice by pressing OK Timer You can use the record timer functionality to programme a recording for a connected Hard Disk or video recorder Totally 30 record timers can be activated Or you can use the sleep timer to specify a time at which the receiver is to switch into standby mode Record timer Sleep timer T
36. rk3 L 5 00 20 30 End Using serial interface The serial data interface DATA offers you the possibility to connect the receiver to a PC Therefore you need a PC and serial cable On the PC side a female SUB D connector with 9 or 25 pins and on Receiver side a RJ11 plug with 6 pins Via this connection you can perform software updates and channel lists up and downloads The required information and software tools are available at the manufacturers homepage Make a contribution to environmental protection Do not throw batteries into domestic waste As a consumer you are obliged to return used batteries You can bring them to a public collection station in your commune or elsewhere where batteries of the same type are sold The following signs can be found on batteries including harmful substances Pb battery includes lead Cd battery includes cadmium X X Pb Cd Hg Hg battery includes mercury Hints for disposal If your device is once disused you should not just throw it into domestic waste B Surely there is a collecting point for old devices where it be collected recycled 33 Trouble shooting Trouble shooting Every electric device can have a malfunction It does not automatically mean that it is defective In most cases it happens because of a feed cable plug and socket connections or access mistakes Please control the following items before taking the receiver to your specialised de
37. rrent and the following programme are displayed in the channel change OSD on screen display Thereby the scale of progression below the programme number signals the temporal progress of the current programme If faded out you can display this information again by pressing OK 11 EPG Electronic Programme Guide EPG Electronic Programme Guide Almost all TV and radio broadcasters provide further information on their programme Your receiver stores and decodes these data and displays them in the so called Electronic Programme Guide EPG This programme preview is activated by using the EPG button The appearing list contains all programmes of the current channel In the headline of the menu channel name date and time are shown Das Erste HD Monday 19 12 2011 20 07 By using the buttons O the channel can be changed without leaving the EPG menu With or lt gt you can select the broadcast you want to be informed about You can get more detailed information by pressing OK Also you can use the EPG list to program a record timer very easily Just press the Record button and activate the record timer in the corresponding menu Please use EXIT to leave this on screen dialog Settings The basic functionality of the receiver is defined in the Settings menu The derivation of your local time against the GMT Greenwich Mean time time needs to be corrected otherwise the displayed times may be wrong Hint
38. s settings No Confirm your choice with the OK button The PIN code is set at the factory to 0000 WARNING You must not forget the PIN code Should this happen please contact your specialist dealer 17 Installation Installation Installation In the main menu select the line nstallation using Installation AY and confirm with OK The Installation menu Antenna configuration will appear Channel search Factory reset Use the buttons AY to make your selection and Software download confirm with OK Installation antenna configuration Choose the required line by pressing and enter your preferred settings with OK 1 Antenna Contains all available satellites By using lt Antenna configur or gt you can select the satellite your LNB is directed to After pressing OK you can rename Antenna 1 Astra 19 2 the selected satellite name Antenna power On LOW Band 9 750 2 Antenna power HIGH Band 10 600 Here you can switch on off the supply voltage DiSEqC Switch A for the LNB 4 Toneburst Switch A 3 LOW Band The oscillator frequency for LOW band can be fine adjusted by pressing lt or gt For directly entering the frequency press OK and use the numeric buttons 1 0 then 4 HIGH Band The oscillator frequency for HIGH band can be fine adjusted by pressing lt or gt For directly entering the frequency press OK and use the numeric buttons 1 0 then 5 DISEqC switch If your receiver
39. s to the appropriate and designated facility In this manner you make sure that the batteries are recycled in accordance with legislature and will not harm the environment All cities have established collection points where electric and electronic equipment and batteries can either be submitted free of charge at recycling stations and other collection sites or be collected from the households Additional information is available at the technical department of your city Ld fi TRIAX your ultimate connection
40. t of the current channel The first site to be seen is site number 100 In order to view a specific page use the buttons 0 9 to enter the three digit page number Your input is displayed in the left corner on the screen When the site number is input completely the receiver starts to search the corresponding site Because the video text sites are sent site by site it may take some seconds until the required site is found Enter 100 at any time to return to the home page of the videotext You may use to quickly page through the complete videotext section of a particular TV channel If you press the TEXT button again you can switch into the mixed mode background transparent Use the TEXT button to return to the normal mode For leaving the video text please press EXIT 27 Connection of external mass storage device Connection of external mass storage device If an external mass storage device is connected to the USB Socket on the rear side of the receiver it can be managed in the menu Mass Storage Device Important Before connecting or disconnecting the mass storage device the receiver must be switched to Standby In the Main menu choose the line Mass Storage Device with AW and confirm with OK This menu will appear Mass Storage Devi Information Formatting Information Move the cursor using the buttons V onto the line Information and press the OK button In the superimposed window you will see
41. your remote control Now anew menu is displayed with two lists displaying the founded TV and RADIO channels Thereby the Status graphic keeps you informed on the progression of the channel search Status scan gt search algorithm is active Status end gt search algorithm is finished You can leave this menu by pressing EXIT If not finished the channel search algorithm is aborted If new channels are found you are asked to store them Yes Select your choice by lt gt and confirm with OK If selected YES the new channels are stored at the end of the channel list now Installation Factory reset This menu item allows you to reset the receiver to its default factory status Afterwards the receiver starts up with the Welcome Screen initial installation again 20 Installation Smartcard Reader The Digital Receiver is optionally equipped with a smartcard reader With an equal smartcard it is possible to unscramble encoded channels The smartcard can be inserted also while the receiver is switched on Insert the smartcard golden chip on lower side towards the receiver carefully into the slot at the front panel of the receiver After the smartcard is inserted the encoded programmes will be unscrambled SMARTCARD To open the menu of the smartcard first select Installation in the main menu and press OK to confirm A submenu generated by the smartcard appears Installation on the screen Ante
Download Pdf Manuals
Related Search