Wave XL460 Monitor
Contents
1. Change brightness from 40 to 60 on all controllers default address setting ATT ADR CMD ___ LEN IHC DAT IDC The brightness data is one byte where 0x00 is min and OxFF is max Acknowledge Ok PATT ADR CMD ___ LEN IHC DAT IDC The controller returns the new brightness data in this case 0x99 60 Acknowledge error ATT ADR CMD ___ LEN IHC DAT IDC The controller returns the previous brightness data in this case 0x66 40 Manufacturer command MAN This command is used to identify the manufacturer of the Monitor Ask for manufacturer ATT ADR CMD __ LEN IHC_ No data must be sent Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company nets Wave XL460 Monitor Acknowledge Ok ATT ADR CMD __ LEN IHC DAT __ IDC The controller returns the ASCII string value for the manufacturer in this case NI North Invent Version command VER This command is used to identify the controller model and protocol version Ask for model version ATT ADR CMD ___ LEN IHC_ No data must be sent Acknowledge O2. See above for further explanation RGB mode wizard This folder is only shown when an RGB signal is present on a RGB input For a detailed explanation of the technology behind a RGB signal for a deeper understanding of how to adjust the Marlin scalar board to accept non standard RGB signal please refer to 14400001 RGB signal detection Control Function Mode selection is a set of parameters telling the display where and how to display the picture horizontal total phase horizontal resolution vertical resolution horizontal position and vertical position It is possible to enter up to 10 different mode selections 1 Activate the Mode selection 2 Choose the desired no 3 Adjust settings under horizontal total phase horizontal resolution vertical resolution horizontal position and vertical position 4 Enter and activate the Save mode parameters Value 0 9 Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company il Wave XL460 Monitor If new mode parameters have been entered it is possible to delete them by using the Clear button The Horizontal Total should
3. Monitor All necessary electrical indications are to be found on the Terminal Plate at the bottom of the Monitor s backside Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company nets Wave XL460 Monitor 24 VDC AC FUSE DC FUSE AC IN 20 30 70 264 VAC TOUCH VGA DVI CYBS 5 IDEO Compass Safe Distance 4 5 m VIDEO P 11606 C1 Figure 1 Left and right side of Terminal Label e Power supply The Monitor can be supplied with 90 264 VAC and or 18 36 VDC The Monitor is connected to AC voltage by means of the standard AC power cable included in the delivery The AC current to the Monitor must be limited by a 3A fuse or similar The Monitor is connected to DC voltage by means of the DC power plug included in the delivery and wires suitable for up to 8 A The Monitor will not be damaged by reversed polarity may it occur e VGA cable Analog RGB The VGA cable is not included in the delivery Remember to fasten the VGA cable s fixing screws for adequate connection e DVI cable Digital RGB The DVI cable is included in a standard delivery The DVI cable is to be connected to th
4. be post northinvent com www northinvent com reproduced without the written permission of the company satel Wave XL460 Monitor 2 4 2 OSD items Depending on the menu chosen different types of items can appear Push button activates a sub menu or a function List a value can be chosen from a list Slide bar slide the bar to choose the desired level from 0 100 ON OFF turns the settings On or Off Information Information contains pure text or value information 2 4 3 OSD items stages Folder items menu items and sub menu items exist in three different stages Color temperature Inactive when the OSD is opened all folders menus and sub menus are by default inactive and the only item that is selected is the Tools folder Color temperature Selected when the user navigates through the OSD part of the selected item is blue It can not be adjusted before activated Press ENTER Activated the item is activated and can be adjusted To activate an item push or temperature the ENTER button on the HMI Human Machine Interface 2 4 4 Entering and adjusting the OSD The OSD menu can always be opened and closed by pressing the MENU button on the HMI except when locked see 2 4 on page 16 Once the menu has been opened it can be navigated up down and righi left using and buttons To be able to adjust the settings an item has to be active which is effectuated by pressing the ENTER b
5. connector with the following pin assignment Pini 23 45 fel fel 9 5 y xiex Een i i enn Interface parameters Baud rate 9 600 Parity no Data bits 8 Start bits 1 Stop bits 1 Handshake no COMMUNICATION PROTOCOL The communication protocol complies with IEC 61162 1 NMEA eyte olf 1 2t04 5 6 7 toLEN 6 LEN 7 Hel Dat DC The min message length is 7 bytes and the max message length is 82 bytes The different bytes are described below Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company ii Wave XL460 Monitor Attention ATT byte This byte identifies the message start ATT 0x07 Command 0x06 Acknowledge OK 0x15 Acknowledge error Address ADR byte ADR Description _ All controllers 0 15 Controller 0 Controller 1 etc Controller 15 Command CMD bytes Brightness Manufacturer Version Monitor Controller Type Data length LEN byte Length of DAT in bytes 0 74 bytes Inverse Header Checksum IHC byte lt is a simple 8 bit checksum of the header data bytes 0 to 5 where a bit wise inversion has been
6. is set for the Source A value under the menu Picture And eventually Source B in case of PIP and Side By Side A sub menu will appear with the following parameters Brightness 30t AO O O O 100 Contrast 30 SJ 100 Saturation 30 CA o n l H 0 CEAO C 100 Color temperature By setting the Color temperature to User a new sub menu appears Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 post northinvent com www northinvent com reserved to North Invent Norway AS This document cannot be reproduced without the written permission of the company eet Wave XL460 Monitor Brightness specifies the darkness or lightness of a color It is measured in percent from black 0 to white 100 At 0 brightness both hue and saturation are meaningless Value 0 100 Contrast is the difference in light intensity between the brightest white and the darkest black Value 0 100 Saturation sets the brilliance and purity of a color that is how much grey is in the color A highly saturated hue pure color has a vivid intense color while a less saturated hue appears more muted and grey At 0 saturation hue is meaningless Value 0 100 Hue is what most people refer to as color A blue button has the hue blue It is the dominant
7. not fit the screen size Adjust the picture positions and frequency with the OSD The picture cannot be adjusted to fit the Check if the video solution and frequency are included in the screen size Mode Table above The backlight cannot be adjusted from Adjust the backlight to 50 with the OSD totally darkness to full brightness using the KNOB control The backlight cannot be adjusted from Set the KNOB control in its calibrated setting little mark above totally darkness to full brightness using the KNOB the remote control Part of or whole picture is blurred Adjust the picture phase with the OSD Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company atati Wave XL460 Monitor 3 4 Cleaning Dust and dirt which typically accumulates on the front of the Monitor can easily be removed using a soft cloth moistened with hot water A solvent can also be used but never use any kind of abrasive compound Oil and grease can be removed using pure alcohol The front glass can be cleaned with any solvent suitable for glass 3 5 Update The technical documentation is subject to change For an upda
8. D division into folders menus SUD MENUS ccccccccseeeccccccsccecccccacccecceccauccececeusceeccecaueesess 12 LALO D E a A EE E E E saan oe E E AAAA E AEA ENEE 13 AS ODI 5 E A E A E E 13 2AA Emering and adj s ne the OSD rersscsireanare seroren rnEeE E E NENEA E NANNE EENE NEES 13 De OS DCO sacs a E E gestae 3es naaeseatecensaunsaes caesar 14 OTE GS ose tee asses ose ieee eng cess uence ees ew cate go ee ese eines E A 15 PROS OM eean E EEA EA NEEN A N AE EAA EAN E ES 17 PAA AAE EE E E EE EEE EEE A tennis 19 ROB modo wiza eaan E E AEE EE EAEE E EEE cae oeeeacaaetacnants 20 al Oene aE E T E AAA E A 21 DD Node TiD e ae i E E E E E et E E 22 DG Remot COMM hepcctsadeetnecdennantaneanenigcuneessiainntnendinnaetinesnenianuse eine deatiendennanaiacantoigeusesndeatextierdeunaneaneaaenagie 23 3 CCIE AN SC CIBC ALOIS a T S 28 Pe My SUMAN AI soins E E N sigs cece N ease uaa tes aon sae ene E E N E eevee ese ee oe 28 3 2 Firmware Revis on table arr eenen EEE E E E E EEEN EEE 29 S OOE SOO E era a A EA OR 29 eLO E i AEE A EAA A E AN AA EAEE A E 30 a AS E E A A E A A E E E E E A 30 d AVEC TANG SAIN SEY UCC seene asec T A TA EAE ERA 30 Specifications subject to changes without prior notice The contents of this page are property of North Invent Norway AS All rights herein are reserved to North Invent Norway AS This document cannot be reproduced without the written permission of the company NORTH INVENT Serhauggata 128 NO 5527 Haugesund Norwa
9. K ATT ADR CMD __ LEN IHC DAT IDC The controller returns the controller model DATO and protocol version DAT1 DAT2 in this case controller model 115 and protocol version 1 0 Controller command MCC This command is used for remote control of the display controller menu functions e g the contrast settings Ask for 50 contrast _ATT ADR The menu function is included in the data bytes DATO 0x82 contrast command DAT1 0x41 a all colours DAT2 0x38 8 first digit of contrast value 0x80 50 of OxFF A 0x30 0 second digit of contrast value se above Acknowledge Ok ATT ADR CMD LEN IHC DAT IDC 0x06 0x4D 0x43 0x43 0x06 0x21 Ox6C The data field is extended with the new contrast values DAT4 and DATS Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company eet Wave XL460 Monitor A complete list of remote control functions can be provided on request Type command TYP This command is used to identify the Monitor type Ask for display type ATT ADR CMD LEN IHC No data must be sent Ac
10. L STD 810F IACS E10 DNV Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company eet Wave XL460 Monitor 3 2 Firmware Revision table Monitor Rev Software Description Signed by Rev ford 3 3 Troubleshooting There are several possible solutions to the same problem please try the first one on the list and then move on to the next if the problem persists PROBLEM POSSIBLE SOLUTION No AC or DC indication and no picture Press the POWER control shortly then press and hold the on the screen control for a while No AC or DC indication and no picture Check the AC and or DC power cable and make sure that on the screen voltage is present at the terminals No picture on the screen but AC and or Press the pad for full brightness DC indication is on No picture on the screen but AC and or Press the MENU control or press and hold the LOCK control for DC indication is on 5 sec and select the correct video source with the OSD No picture on the screen but AC and or Check that a valid video signal is present on the selected source DC indication is on use e g another Monitor The picture do
11. Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company aai Wave XL460 Monitor the Monitor Standard video signals are listed in the Mode Table section below Press the Power control once the Power LOCK and relevant AC DC indicators will light up The control and indicator backlight can be adjusted using the controls When Locked e g ECDIS mode the indicator and the control panel backlight will follow dimming of the display backlight In ECDIS mode the backlight control and indicator are preset to Day Dusk and Night controlled via RS232 The Monitor will search for a video signal on the last selected input source If the Monitor states No Input Signal Going to Sleep the correct source can be selected using the OSD see below The default source is the standard VGA input The screen brightness can now be adjusted using the controls on the Front Panel and the picture positioning and size can be adjusted using the OSD see below 2 3 Source Input Messages After start up of the Monitor a short message will appear in the same space provided for the OSD see below The different messages are explained in the following table Message Explanation Analog RGB searching The Monitor is searching for a valid video signal connected to the VGA input Digital RGB searching The Monitor
12. Wave XL460 Monitor USER S MANUAL WA460 01 MON 01 0001 Specifications subject to changes without prior notice The contents of this page are property of North Invent Norway AS All rights herein are reserved to North Invent Norway AS This document cannot be reproduced without the written permission of the company October 2014 NORTH INVENT Serhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 post northinvent com www northinvent com NORTH INVENT Wave XL460 Monitor Table of Contents RR 210 a pene eter Onn T EAE IE PEIE E ne E TEE ee E E ee ee eee ee 3 1O Terms and abbreviation S ws tccaaseatnecncenniaosenneesacenteenasmbscdcasensaeadecnigtaniau EA De Raia 3 R EE a A E E A A E E T A E taawecvaneieses 3 12 Proda idon oa EEE EE E E E A E E E E A 5 Me E Mie ACI a e E E E E E A E E E E A oa 6 E TE E R I a A E E E E E AE E E E N A E E T 7 Lo Mechanical Dimen ons ect oncsaccuaenteccione eacxsnetecetanetescenamtenciovt a 7 136 IO CtaC all MIS ha Ml AMO ssa secs soccer E T 7 2 Operating Instructions 52rsinss clasvesacecencsdadsexessnessseddedaavasienesenes ud taxesascia idelepnasoacyoxesdaldamsaccia eitehasadoomnaretdaiaemeeemedtx 10 DN OM TOIS ANG TING ANOS E E E O E onic ncurses eset 10 DDFS AM AU a cee cetysanceGaa crane selva sie Gea sateen selvaecie Gaetan A seen su E sek osecieousieent ses each ET 10 Died Source niput Mesra CS sen e a E ene AR A N 11 DAO SCS et Dipha OSD hern E E ES 11 2 4 1 OS
13. be equal to or higher than the horizontal resolution plus horizontal position See explanation under Horizontal position The phase settings stabilize the picture by removing horizontal noise and sharpening the image of characters The value for the horizontal resolution of the display is adjusted here The vertical resolution of the display is adjusted here Z The chosen value decides where the picture is placed horizontally on the display Horizontal position is equal to the horizontal front porch horizontal back porch which is the field used to specify the number of dummy pixel clocks to insert at the beginning pulsing the line clock pin and end of each line or row of pixels before After the line clock for the previous line has been negated the value in horizontal back porch is used to count the number of pixel clocks to wait before starting to output the first set of pixels in the next line Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company il Wave XL460 Monitor Display supply Information about the voltage supplied for the display The name and input signal data of the source
14. distances are mentioned on every Monitor or in the accompanying handbook A safe distance takes into account both the constant effect on a magnetic compass of the presence of magnetic material but also any variable effect due for instance to electrical circuits or the opening closing of drawers or panels Thus provided that a Monitor is not placed in a position nearer to the centre of the bowl of a magnetic compass than the recommended safe distance the Monitor may be installed or removed without any need for adjustment of that compass WA460 01 MON 01 4 50 m The compass safe distance is also indicated on the terminal label of every Monitor as shown on Figure 1 Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company iia Wave XL460 Monitor 2 Operating Instructions The following instructions assume that the Monitor has been correctly installed and that the commissioning work has been finalised 2 1 Controls and indicators Controls and Indicators are placed on the User Panel in the lower right side of the Monitor Normal functioning of the Control knobs and Indicators are explained in the fol
15. e DVI I terminal Be sure to use a high quality DVI cable with correct termination of shield Remember to fasten the DVI cable s fixing screws for adequate connection e Video cables Video signals can be obtained by connecting the Monitor to the S VHS S Video and CVBS composite video terminals The video cables must be of high quality in order to avoid signal s interference e USB cable An F M USB cable to connect touch to PC is included Cable can be fixed with a wire strap at the terminal plate e RS232 cable The Monitor is equipped with a standard 9 pin D SUB female connector for RS232 remote control Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Serhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company Wave XL460 Monitor Further information about this interface and the remote control is to be found in the Remote Control section e Compass safe distance Every component of type approved equipment is tested in order to determine the minimum safe distances at which it should be installed from both the steering and the standard magnetic compasses so not to significantly affect the accuracy of these compasses The safe compass
16. e Monitor setup Value 0 1 or 2 Save monitor setup Saves the present settings entered by the user See explanation above Recalls the settings depending on which Setup Selection is chosen 1 Choose the desired setup under Setup selection 2 Activate the Recall Monitor setup button Horizontal position of the OSD menu on the display Value 0 100 Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company satel Wave XL460 Monitor 7 a The Source enabling control decides which input sources should be enabled ourc apiInc iiai and which should not By activating the Source enabling button a sub menu appears where input sources can be activated or deactivated by choosing the ON or OFF setting A source has to be set to ON to be able to be adjusted The list below is for Marlin Basic scalar boards If a Marlin Single scalar board with extension module is used the list will reflect the inputs present on the Marlin Single plus the extension board Source enabii 1g Composite SVideo Component on N Which source will be shown here depends on which component
17. enabled will be informed here DVI A 1280x1024 60Hz Info box showing backlight Time in hours the backlight enable mode has been turned on time Info box showing power on Time in hours the Marlin scalar board has been turned on time 2 5 Mode Table The table below lists the basic video modes currently set in the Monitors Monitor LCD resolution Video 46 resolution 1920 x 1080 640x350 PO 640x400 Po 640x870 A O S 720x350 Po 720x480 PO 720x576 Po 8oox600 PO 832x624 AO y 852x480 PO 960x720 Po 1024x768 PO 1024x 1 024 Po 4 053x754 PO 1056x768 Po 1120x750 Po 4452x864 PO 1452x870 Po 1452x900 Po Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company iiaii Wave XL460 Monitor Monitor LCD resolution Video 46 resolution 1920 x For each video resolution the most common picture frequencies will be available typically in the frequency range 30 55 Hz for the 46 monitor Additional modes can be added upon request 2 6 Remote control The remote control uses the RS232 interface on the video controller ELECTRICAL CONNECTION 9 pin D SUB female
18. ications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company ii Wave XL460 Monitor Sets the duration for the time out of the OSD menu that is how many seconds should pass with menu inactivity before the menu closes Value 5 20 sec No timeout How many seconds the logo will be shown on the display at start up is adjusted here Value 1 20 sec No logo Sets the time that should pass before the display changes state to power save after input signal is removed Value 1 20 min No timeout Locks the keypad To unlock the keypad again press the LOCK and the MENU buttons for 5 seconds Value ON OFF WARNING Do not lock keypad if only IR remote is used The access is only granted through keypad or RS232 NOT through the IR remote Reinstalls the settings provided by the factory Note The OSD menu will automatically close after choosing Factory Default A setup is a combination of settings adjusted by the user It is possible to save up to 3 different setup combinations 0 1 and 2 The procedure is 1 Adjust the desired settings 2 Enter the Setup selection and choose 0 1 or 2 3 Choose the Sav
19. ion e Each Wave Monitor is designated as below WA XL460 WA 460 01 MON 01 XXXX Where WA stands for Wave 460 for the display s Size 01 in third coulomb for the hardware Revision MON for Monitor 01 in fifth coulomb for standard version of Wave and xxxx for identification of minor variants flash logo OEM labels etc Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company eet Wave XL460 Monitor e Each Monitor is constituted by the following set of components Front glass with multi touch Display Frame and all necessary electronic components Rear cover and Terminal plate 1x Power AC Cable 1 x DC plug 1 x DVI Cable 1 x USB cable optional RS232 cable Tilting unit e Each Monitor presents the following materials and features The Front Display Frame and Cover are made of Marine Grade Aluminium allowing to reduce weight while eliminating corrosion problems The electronic set of components includes a specifically designed Power Supply a high quality Display Controller an integrated backlight LED driver and a custom made Interface B
20. ions subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company ii Wave XL460 Monitor 1 2 Product identification On the front lower right a label with productidentification is placed See example on picture below WA460 01 MON OT Marhh brwemt Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Serhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company ees 1 3 Main schematic overview Power in AC Power in DC gt TFT power C yy hd C Ji Backlight control E Touch USB Human Machine Interface HMI oF BRIL Le DC om mama CTP Fed Eeee O lt 1 RS232 ji RGB graphic data input Loo o ou data input DVI I Composite Video graphic data data input Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of N
21. is searching for a valid video signal connected to the DVI input S Video searching The Monitor is searching for a valid video signal connected to the S VHS input The video signal on the selected input source is out of range Input signal exceeds bandwidth when PIP SBS or instead of Out of range When the Monitor detects a valid video signal it will shortly indicate the source input resolution and frequency of the input signal as well as the video mode number The input source can be selected using the OSD see below If the video signal is out of range either the resolution or frequency is too high for the Monitor The message is also given if the current video mode is not included in the Mode Table see below Additional video modes can be added upon request 2 4 On Screen Display OSD Most functions of the Monitor can be controlled using the OSD The OSD is activated by pressing the LOCK or MENU control The monitor is equipped with a lock function which prevents accidental use of the OSD The lock function does not affect the indicator brightness and backlight controls The status of the lock function is controlled by the OSD and remote control The monitor is always Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to No
22. knowledge OK ADR CMD _ LEN IHC DaT WDC The controller returns the ASCII string value for the Monitor type in this case SL213 Sea Line 21 3 inch Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company nets Wave XL460 Monitor 3 Technical specifications 3 1 Summary LVDS display 46 1 920 x 1 080 0 0 17675 H x 0 53025 V mm 15 100 kHz H 30 100 Hz V up to 1 280x1 024 Frequency 15 100 kHz H 30 55 Hz V up to 1 920x1 200 Power supply Voltage 90 264 VAC 18 36 VDC 90W AC Power Consumption 90W DC Controls Power Brightness Menu Set amp Lock with dimmable backlight Indicators Input power AC amp DC with LED Input connectors ela D SUB 15pin female AC power IEC Inlet amp DC screw Control Input RS232 D SUB 9 pin female Dimming range 0 100 Dimming ratio 1000 1 15 C 55 C 5 F 131 F IEC 60945 20 C 60 C 4 F 140 F Dimension amp Weight 1175 0 x 762 6 x 69 0 mm WxHxD Weight 36 Kg Dimension amp Weight with TBD tilting unit WxHxD Weight TBD IP42 Enclosure protection Standards amp Approvals IEC 60945 MI
23. lowing table Control indicator Function _ _ _ Press once to switch the Monitor ON oe Press for 5 sec to switch the Monitor OFF A Indicates that the Monitor is supplied with 90 264 VAC D Indicates that the Monitor is supplied with 18 36 VDC Press once to activate the OSD in unlocked state LOCK Press LOCK and MENU for 5 sec to unlock and activate the OSD in locked state Press once to activate the OSD in unlocked state MENU Press once to deactivate the OSD again Press once to change from sub to main menu Press to indicate change the video input source OSD not active Press once to go to the selected sub menu OSD active Press once to set or unset the selected sub menu OSD active Press and hold to increase the indicator brightness OSD not active Press once to select the next menu OSD active Press or hold to increase values OSD active C C SET Press or hold to decrease the indicator brightness OSD not active Press once to select the previous menu OSD is active Press or hold to decrease values OSD active BRILL SETMENU POWE O00 Figure 2 Front Panel with controls and indicators 2 2 Start up Ensurethat powerand_a_valid_video signal_are Supplied to Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are S rhauggata 128 NO 5527 Haugesund Norway
24. n the sub menu will be selected in this case the Source enabling button 4 Use to navigate to DVI A or other Source input and press SET to activate 5 Navigate down with the button until you have selected the menu item Saturation 6 Press SET to activate the menu item 7 Use or to set the desired value for the saturation 8 Press SET to validate the change the OSD automatically jumps one level back 2 4 5 OSD content The OSD is designed with 6 different folders Tools Functions Source Picture RGB mode wizard and Info each of which has their own menu Several of the menu items furthermore have sub menus to be navigated through In the following pages the different settings will be described Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 post northinvent com www northinvent com reproduced without the written permission of the company nets reserved to North Invent Norway AS This document cannot be Wave XL460 Monitor Tools a e Backlights are used to illuminate displays In small displays they are often used to increase readability in low light conditions The OSD allows for the backlight to be dimmed from 100 0 At 0 the backlight is turned off Value 0 100 LED brightness When sho
25. oard All our Monitors use identical Power Supply and User Panel The Power Supply can be supplied with 90 264 VAC and or 18 36 VDC and even be used as a part of an UPS All our Monitors come with VGA DVI S Video and Composite video inputs and a RS232 input for remote control purposes Pixel pitch is 0 17675 mm horizontal x 0 53025 mm vertical Pixel pitch equals 1 82 m viewing distance with a viewing angle of 1 minute of arc as required in IEC 62 288 section 7 5 1 e Each Monitor complies with the following international Standards and Requirements The XL460 monitor has been tested by the testing body SP SP Technical Research Institute of Sweden A S Copenhagen and found to comply with the requirements of the International Association of Classification Societies IACS IEC 60945 IEC 60533 IEC 60529 and as well as the selected requirements of MIL STD 810F The 46 Wave XL monitor is also tested according to IEC 62288 IEC 62388 and IEC 61174 and thereby ECDIS approved pending The XL460 monitor is approved in compliance with the international standard IEC 60945 2002 Clause 4 4 Equipment category b protected from the weather formerly class B Maritime navigation and radiocommunication equipment and systems General requirements Methods of testing and required test results The compass safe distance indication is placed on the rear label see figure 1 and is valid for the Monitor only Specificat
26. orth Invent Norway AS All rights herein are Serhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company Wave XL460 Monitor 1 4 Packaging and delivery Please check the delivered goods immediately on receipt with respect to damages caused by transportation and inform the delivering freight carrier immediately on site about any visible transport damages Additionally inform us immediately in writing at the latest within 5 work days about any visible transport damages At reception the delivery includes the following items Wave Monitor Wave User s Manual DVI cable AC power cable DC power plug USB cable for touch RS232 cable optional Monitor WAVE XL 460 Type WA460 01 MON 01 0001 Serialno A140041 NORTH INVENT Compass safe distance Supply Voltage 90 264 VAC 24 VDC 20 30 POWER COMSUMPTION App 90 W AC 90 W DC Designed in Norway by North Invent Norway AS Sorhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 Label on the backside of monitor with product identification and serial number 1 5 Mechanical Dimensions For panel cut out drawings and mechanical dimensions of monitors see data sheets 1 6 Electrical installation All electrical connections are to be found on the lower back side of the
27. performed The checksum must be initialised to 0 The 8 bit sum without carry of bytes 0 6 must be OxFF IHC OxFF ATT ADD CMD0 COM1 COM2 LEN where only 8 bits are used If a message checksum fails the controller will reply with the attention byte 0x15 and no data bytes Data DAT bytes The data bytes will only be send if data length LEN is greater than 0 The data bytes are designated DATO DAT1 DAT2 etc Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company eet Wave XL460 Monitor Inverse Data Checksum IDC byte This byte will only be send if data length LEN is greater than 0 It is an 8 bit checksum of the data bytes bytes 7 to LEN 6 where a bit wise inversion has been performed The checksum is initialised to 0 The 8 bit sum without carry of bytes 7 to LEN 7 is be OxFF IDC OxFF DAT0 DAT1 DAT2 where only 8 bits are used If a message checksum fails the controller will reply with the attention byte 0x15 MESSAGE EXAMPLES The following examples are the typical messages used Brightness command BRT This command is used to change the brightness of the Monitor
28. rth Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company ii Wave XL460 Monitor locked when a valid RS232 signal is available If the Monitor is in locked state the OSD can only be activated by pressing the LOCK and MENU buttons at the same time for 5 sec The screen backlight brightness can be adjusted using the controls on the front panel but it can also be adjusted using the OSD and remote control Normal operation shall be backlight 100 The next and previous menu can be selected using controls The sub menus are selected using the SET control and values can be increased decreased using controls The SET control is also used to set the value and leave the sub menu Press the MENU control once to return to the main menu and once again to leave the OSD The OSD will be deactivated the selected period after the last control has been pressed OSD timeout 2 4 1 OSD division into folders menus sub menus source enabling Source enabling RGB z VGA ON W orF Composite on orr SVideo Figure 3 On Screen Display Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot
29. ted version please visit our website www northinvent com 4 Maintenance and service Wave monitors are conceived so to be almost maintenance free If the Monitor malfunctions please check if the problem can be solved with troubleshooting 3 3 lf the problem persists please contact North Invent for service instructions Allow app 1 hour stabilization time before measuring luminance and colors Wave XL460 UM Rev1 0 10 2014 Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 post northinvent com www northinvent com reserved to North Invent Norway AS This document cannot be reproduced without the written permission of the company ii
30. thinvent com www northinvent com How the picture should be presented on the display is adjusted here There are three different display modes Single A single picture is shown on the display default PIP Picture In Picture where a small sub window shows a second picture Source A or source B within a larger picture the opposite source Side by Side The display is divided into two pictures representing Source A and Source B Value Single PIP or Side by Side It is possible to adjust the settings for one input source at a time If Source A is activated a sub menu appears Composite SVideo Component In this sub menu the user chooses which input should be active Their settings are adjusted under the Functions menu Size 30 0 x 100 Horiz 10 0 100 Vertical position 30 oo 100 Source A has already been explained and Source B decides which input should be the second input NORTH INVENT Phone 47 48 84 02 00 NORTH INVENT reproduced without the written permission of the company Wave XL460 Monitor Size The size of the PIP picture is chosen here Horizontal position The chosen value decides where the PIP picture is placed horizontally on the display starting from the upper left corner Vertical position The value decides where the PIP picture is placed vertically on the display from the upper left corner If Side by side is chosen the following menu is
31. utton To make adjustments in the OSD follow these steps 1 Press the MENU button on the HMI to activate the OSD 2 Navigate up and down in the different folders with and buttons 3 When the desired folder is partly highlighted press the SET button to activate the menu 4 Navigate with the and buttons until the desired control has been reached and partly highlighted To gain adjustment control press SET The control will be highlighted and can now be adjusted 5 Press to increase the value or to decrease the value 6 When the right level has been reached press SET once again to activate the adjustment and automatically jump one level back 7 To exit the OSD press MENU The following exemplifies how to adjust the settings for Saturation 1 Press MENU to activate the OSD Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company nets Wave XL460 Monitor 2 Use or to navigate up or down until you have selected the Functions folder the icon will be coloured 3 Press SET to activate the folder the folder will turn blue and automatically the first menu item i
32. wavelength of a color Value 0 100 The color can be set to Default User Cold or Warm Cold The predominant tones are blue and violet Warm The predominant tones are red and orange User Activates the menu items Red Green and Blue where the value can be set between 0 100 Value Default User Cold or Warm Warning Manual setting of above parameters away from the factory default or ECDIS settings may inhibit visibility of information particularly when using the night color tables Factory default settings of Brightness Contrast Saturation Hue Red Green and Blue are 50 Specifications subject to changes without prior notice The contents of NORTH INVENT this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway Phone 47 48 84 02 00 reserved to North Invent Norway AS This document cannot be post northinvent com www northinvent com reproduced without the written permission of the company aiat Wave XL460 Monitor Picture If Single is chosen as display mode the following menu appears Source A If PIP is chosen as display mode the following menu will appear Specifications subject to changes without prior notice The contents of this page are property of North Invent Norway AS All rights herein are Se rhauggata 128 NO 5527 Haugesund Norway reserved to North Invent Norway AS This document cannot be post nor
33. wing a graphic signal or video signal the following scaling modes exists Fill aspect Fill aspect Scaling mode depends on panel and source signal aspect ratio This mode preserve the correct aspect ratio of the input signal so if a 4 3 signal is to be displayed on a 16 9 display this adds black bars on both sides One to one 1 1 representation of the input signal If a 640x480 signal is to be displayed on a 1024x768 panel you will see the picture centered using 640x480 pixels shown with a black frame around tt Fill all Regardless of input and output resolutions the input picture is scaled to fit the screen Auto This means that for Composite or S Video signals provided Wide Screen Signalling WSS is available input signal is automatically scaled depending on the ancillary data transmitted This is usually sent by TV broadcasters or by DVD players according to the aspect ratio of the video Anamorphic For 16 9 signals generated by DVD players the signal is 16 9 but is stretched to fill the screen with no black bars so the picture if displayed ona 4 3 screen would result in tall people This will de stretch the picture so that the given correct aspect ratio is restored Auto and Anamorphic will only appear if video input has been chosen Value Fill aspect One to one Fill all Auto and Anamorphic If a still picture is needed the present frame can be frozen by selecting ON in this property Value ON OFF Specif
34. y Phone 47 48 84 02 00 post northinvent com www northinvent com NORTH INVENT Wave XL460 Monitor 1 Foreword Thanks for purchasing a North Invent Wave Monitor Our series of rugged TFT LCD Display Monitors are conceived and built with the greatest care and state of the art electronic and software features North Invent focuses its full expertise in offering dedicated display solutions matching with your highest requirements and use Before starting operating the Monitor we would like to suggest that you carefully read through the present document as our aim with this User s Manuel is to give you the best experience in using our Monitors May you have any suggestions for improvements or any feedbacks about this manual the Monitor and or its features feel free to contact us We will be pleased to oblige This User s Manual is for use only with our Wave Monitors To assess which series of Monitor you are in possession of please check the Serial Number plate at the back of the screen The mention shall bear WA460 May you have a different series of Monitor please contact us so to have the proper manual sent to your attention 1 0 Terms and abbreviations DVI Digital Visual Interface DVI A Analog DVI I Integrated HMI Human Machine Interface LCD Liquid Crystal Display LED Light Emitting Diode OSD On Screen Display RGB Red Green Blue TFT Thin Film Transistor VGA Video Graphics Array 1 1 Monitor descript
Download Pdf Manuals
Related Search