- Strong Australia
Contents
1. 2 Play Mode gt Loop Set the Loop state on Normal Reverse Random Single or Off gt Slide Show Interval Set the Slide Show Interval from 2S 10S gt Photo View Mode Set the Photo View Mode state on Full Screen 2x2 Thumbnail or 2x3 Thumbnail 3 PVR Setting gt Record Partition Select the Partition where save your record or other 16 result of your operation gt Record Mode Set the Record Mode Channel or Transponder gt Record Type Set the Record format to TS or PS gt Record Time Set the Record Default Time off 30 60 90 120 minute or input number directly gt Auto Timeshift Set timeshift mode to auto when recording gt Timeshift Buffer Size MB Set the Timeshift Buffer Size between auto off 100 200 400 800 1600 3200 or 6400MB gt Timeshift Need Save Set if the Time shift portion is to be saved to the external media as a recording gt Play Start Pos When playing the PVR file set the Play Start Position whether head start of the file or last position when last stopped in playback of the file 7 2 2 Play Files 1 PVR Same as movie 2 Movie 1 Press the VOL VOL to highlight the Movie 2 Press the CH CH to change the folder or file and press the OK button to open the folder or play the movie file It supports 3GP AVI MKV MP4 MOV MPG TS M2TS DAT VOB format movie files 3 Music 17 1 Press the VOL VOL to highlight the2. 20 11 Additional Information 11 1 Trouble Shooting Before contacting your local service centre please read the tips below carefully If the problem persists after completing the following procedure please contact your local product distributor or service centre for further instructions 1 No message displayed on the front display The product will not switch on Check the main power cable and make sure it is plugged into a suitable power outlet e Check that the mains supply is switched on Connect the power cable to a different power outlet Check that the power switch is on at the rear of the product where applicable 2 No picture e Make sure that the product is powered on and in operation mode Press the STANDBY button e Make sure that the AV RCA or HDMI cable is firmly connected to the TV Make sure that the antenna cable is properly connected to the product e Be sure to activate channel search e Check the brightness level of the TV e Check if the channel is currently on air Contact the broadcaster to ensure that the channel is running 3 Poor picture sound quality e Make sure there is no mobile phone or microwave oven near the product e Adjust the antenna direction to get a better picture 21 e Set the antenna power in menu to On if you use the active antenna to improve the reception where applicable 4 No or poor sound e Check that your AV HDMI cable is connected correctly
3. e Check the volume levels of your TV set and the product e Check if the product or TV is on mute e Check audio type or soundtrack option where applicable 5 Remote control does not operate e To control the product the top end of the remote control should point directly towards the receiving part of the product Remove and reinsert the batteries in the remote control e Replace the batteries in the remote control for a new set 12 Technical Specifications MPEG Transport Stream MPEG 2 ISO IEC 13818Transport stream specification Profile Level MPEG1 MPEG 2 MP ML H 264 VC1 DV DivX and MPEG4 Input Rate 80 Mbps for MPEG Transport Stream and 25 Mbps for DV streams Aspect Ratio 4 3 16 9 Video Resolution 576i 576p 480i 480p 720p50 720p60 1080i 1080p Audio Decoding MPEG 2 layer I and II Music cam MPEG4 AAC and MPEG4 AAC HE AAC Dolby Digital AC 3 with bit rates up to 640 K bits s LPCM up to 48 KHz MP3 Audio Mode Single channel Dual channel Joint stereo Stereo Sampling 32 44 1 and 48 KHz 22 Power Supply Input Voltage AC 100 240V 50 60Hz Power Consumption Max 25 W Protection Separate internal fuse Input shall have lightening Protection Physical Specification Weight Net About 2 5kg Operating Temp 0 C to 40 C Storage Temp 40 C to 65 C 23 24 TRONG 7 STRONG AUSTRALIA PTY LTD 60 WEDGEWOOD ROAD HAL
4. 10 1 Recording and TimesShlft oooooconnocononccnoncncnonncoonncnoncnnnncncnnn nono nncnoncnos 20 E eee 20 11 Additional Informati0N oooooonconncnncnnncnnonnonncooncnnnconnconncnnccnnccnnccnnno 21 11 1 Trouble Shooting oooocnonccnonccionononncnoncnconnncnnn conan ncnoncnnon crono nncnnnncnnnnnos 21 12 Technical Specifications ooooooocnnonccionncnonnconnnocononononncnnn conan cnconcnonos 20 Instruction Safety Precaution This STB has been designed and manufactured to satisfy the international safety standards Please read the following safety precautions carefully before operating this receiver Main Supply Before operating please check the units operating voltage is 100 240V AC 50 60HZ Overload Do not overload a wall outlet extension cord or adapter neither use damaged power cord or touch it with wet hand as this may result in electric shock ILiquid The receiver shall not be exposed to dripping or splashing water and that no objects filled with liquids such as base shall be placed on the apparatus E Ventilation Keep the slots on top of the receiver uncover to allow sufficient airflow to the unit Do not put the receiver on soft furnishings or carpets Do not expose the receiver to direct light or do not place it near a heater or in humid conditions Do not stack other electronic equipments on top of the receiver Cleaning Plug out the receiver from the wall outlet before cleaning Clean
5. Content TOSCO RR Gees a es 4 Referente AN 6 2 Product Overview ici dt lt 7 2 1 Eront Panels nenne tee ita 7 2 2 Rear Panel uses zfaneais tab eaten nenn 8 2 3 Remote Control Unit RCU oo cccccessceessecsseesseeeeeeeeseeeneeeeseeenseeene 8 3 Installation ias 9 3 1 Manual scan euere sure BRBRRRBS SER ES 10 3 2 AO SCAM seen OAN 11 3 3 Antenna power setting oooooooccoonccoooncnonncnoncncononcnnnnonon conan no nonononcnnnnnonns 11 3 4 Factory Default oooooononccnooccnoncncoooncnonnononconononconnncnnonononncnon nn non aia 11 4 Edit Ch np l A A a a 11 4 1 VV Badio Channels coco un ra np aan 11 4 2 TV Radio Favourites cccecccesecesscesecesecesecececececeneceaecececaecaeceaeeeaeenes 12 AS DOr CHANNEL Bence rines a A E A 12 44 User Channel Last u engsten 12 Sa SEHINSS en nalen Tr Se eo 13 5 1 System Settings ita 13 LOS SD Sp a a 14 5 3 Parental Control mitad icdats 14 A A 14 5 5 Color Settings ueno 14 6 Clock and Timer RecordiNg oooooooonnoccconcncoooncnonncnoncnconcncnnnnononccnoncnos 15 TEX PAM SOM A ia 16 A A ARA 16 ALU SB ii 16 TADOUS TB es unsere ees leat nas cusco dona our 18 8 Basic Operation oi Sa ee a Se 18 8 2 EPG is 18 8 9 SUMS as A Pa 19 NO 19 8 7 Program Information ccccccsccesseceeessseeseeceeeeeeeeeeseecseeesseeeneneeeaes 19 9 Channel Eist u nam 8 mes ea Bone Email 19 E OKREiste ran enge 19 9 2 Favorite List neuen einig gem sb un une ipn 20 10 USB Control iia 20
6. Music 2 Press the CH CH to change the folder or file and press the OK button to open the folder or play the music file It supports mp3 ogg wav and flac format music files 4 Picture 1 Press the VOL VOL to highlight the Photo 2 Press the CH CH to change the folder or file and press the OK button to open the folder or play the picture It supports bmp jpg and gif format photos 5 Play List You can play the movie photo music PVR files in the Play List 7 About STB Menu gt SETTINGS gt ABOUT STB ABOUT STB can get the information about the STB such as product name software amp hardware version and serial number and so on 8 Basic Operation 8 1 Audio You can select the language you prefer in Audio if the current program is available in multiple audio languages 8 2 EPG You can view the EPG information of all channels in time and date order 18 1 Press the EPG button 2 Press the GREEN button to switch EPG mode between Weekly EPG and Day EPG 8 5 Subtitle You can select the language for the subtitle if the program provides subtitle information 8 6 Record You can record programs to an external USB flash drive or HDD not supplied Press record for instant recording or set up an event timer via EPG or Timer button by default instant recording will record for 99 hours so press the record button again to change the duration using the remote 8 7 Program Info
7. does not matter 3 4 Factory Default You can restore the product to the factory default and you can also set it up according to the wizard 1 Menu gt INSTALLTION gt Factory Default 2 Input the password default password is 0000 3 Highlight the option you want and press the OK button to execute it Tip If you select yes all data and settings will be lost 4 Edit Channel In the Channel menu you can edit the channels that you want to play in the Normal Play mode The functions available here include TV channel editor Radio channel editor 4 1 TV Radio Channels Menu gt EDIT CHANNEL gt TV Radio Channels 11 Edit Channels enables you to move delete rename lock unlock the channels in the channel list conveniently you can press lt gt button to move delete rename lock unlock press 4 v button to select channels Tip Radio Channels operation similar to the TV Channels Note If the highlighted channel is locked press the OK button to switch to Unlock 4 2 TV Radio Favorites Menu gt EDIT CHANNEL gt TV Radio Favorites You can add or remove channels from the favorite groups 4 3 Sort Channels Menu gt EDIT CHANNAL gt Sort Channels Highlight the option you want and press the OK button to sort the channel list You can sort by LCN logical channel number Transponder Default Favourite alphabetical and provider service ID 4 4 User Channel List User Channel List allows
8. LAM VIC 3803 Ph 61 3 8795 7990 FAX 61 3 8795 7991 HELP DESK 1800 820 030 tech strong com au WEBSITE www strong com au 25
9. RIC KEY 0 9 Enter a TV radio channel number menu option number 22 ASPECT Change the screen mode 23 TV R Switch between TV and RADIO 3 Installation You should install the receiver when powering on your product for the first time after purchase Tip The default password is 0000 If you have forgotten your password please contact your local product distributor 3 1 Manual scan Manual scan function would only add newly found services to STB database without any database clearing action User needs to know the target scan frequency and bandwidth in advance 1 Press lt OK gt to enter Manual Scan menu 2 Press lt Up Down gt to focus on Frequency 3 Press GREEN button to add Frequency and press lt 0 9 gt to input frequency value 4 Press YELLOW button to edit Frequency 5 Press BLUE button to delete Frequency Press RED button to start manual scan and press lt Exit gt to cancel scan 10 3 2 Auto scan Auto scan function would empty all sevices in STB database at first Then scan the frequencies one by one which are stored in the default frequency table corresponding to current Country Setting 1 Press lt OK gt will appear a choice to network search yes or no 2 Press lt OK gt start auto scan whether network search yer or no 3 3 Antenna power setting This is DVB T2 5v control for passive antennas please set it to OFF If active antenna off or on
10. T2 12 Recall List If you set ON when you press Recall button of RCU you can get the recall list If you set OFF when you press recall button you can go back to the last program you have selected 13 Low power standby switch to low power standby 13 14 Front Panel Light Changing the value of this option allows you to adjust the brightness of the front display panel 5 2 OSD Setup 1 Menu Transparency Set the transparency of all menus 2 Display Mode Select the output resolution between 1080p 1080i 720p 576i or 576p 480i or 480p 3 TV Type Set the TV Type on PAL NTSC Auto state 4 Screen Mode Set the display format according to the screen ratio Select TV screen mode either 4 3 or 16 9 according to the TV type or press the MODE button of RCU directly 5 OSD Timeout Set the time of the OSD to disappear after no remote control action 5 3 Parental control Menu gt SETTINGS gt Parental Control Parental Control allows you to set limits for each program or change your previous password You can also lock the changes you have made using Installation Lock Edit Channel Lock and settings Lock And you can change Age Rating 5 4 Calendar Menu gt SETTINGS gt Calendar You can use button CH and VOL and 2 4 6 8 to adjust the date Pressing the GREEN button you can add a memo 5 5 Color Settings Menu gt SETTINGS gt Color Settings Color Settings you can edit the Brightness Contrast and Satur
11. Y TRONG SRT 5432 User Manual Warranty Information This product comes with a 12 month manufacturer s warranty from the date of purchase This unit has a 30 days replacement warranty for manufacturing faults Within this period please return the faulty product with all its supplied accessories to either the place of purchase or STRONG Australia accompanied by the original purchase receipt After this 30 days period the unit must be returned to STRONG Australia for testing and if deemed faulty will be repaired or replaced at the discretion of STRONG Australia Pty Ltd The faulty product can either be sent to STRONG Australia directly or via your place of purchase for evaluation STRONG Australia will cover any reasonable costs incurred in returning the faulty product for evaluation should the product be deemed as genuinely faulty If the product is found to have no fault the costs incurred in delivering product to and from STRONG Australia will be the customer Our goods come with guarantees that cannot be excluded under Australian Consumer Law You are entitled to a replacement or refund for major failure and for compensation for any reasonably foreseeable loss or damage You are also entitled to have goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure STRONG Australia 60 Wedgewood Rad Hallam VIC 3803 Ph 61 3 8795 7990 FAX 61 3 8795 7991
12. ation 14 6 Clock Timer Settings Menu gt SETTINGS gt Times 6 1 Time Settings Menu gt SETTINGS gt Times gt Time Settings Time Settings will set the time mode time zone and summer time 6 2 Event Timer Event Timer You can set up to 8 timer events It will record or play the program automatically according to the timer event list that you set 1 Menu gt SETTINGS gt TIMES gt Event Timer or press the TIMER button directly 2 Press the RED button to setup a timer and press the OK button to save the timer after setup 3 You can press GREEN button to edit timer 4 You can press YELLOW button to delete timer 6 3 Sleep Timer SLEEP Timer can set the automatic turn off time 1 Menu gt SETTINGS gt TIMES gt Sleep Timer 2 Press the VOL VOL button to select the option or input the number at Min option 3 Press the OK button to save 15 6 4 Standby Time If set YES the receiver will go to standby mode after the timer if set NO it won t be standby 7 Expansion 7 1 Games Menu gt EXPANSION gt Games Games In this menu there is a selection of games that you can play 7 2 USB Menu gt EXPANSION gt USB or press the USB button directly Note It supports FAT FAT32 and NTFS format USB disk or USB HDD 1 Tool In USB menu you can press the RED button to select Rename Delete Move To Copy To sort the folders the files And also can create the new folders and format the disk
13. de 6 Y Change channel in viewing mode and move the cursor down in menu mode 2 2 Rear Panel DQ 0 1 ANT IN Connect the antenna cable 2 ANT OUT Loop out to pass signal through 3 COAXIAL Digital Audio output Optical 4 DV OUT Connect to the TV using an HDMI cable not supplied 5 AUDIO R L VIDEO Connect to the TV using RCA cabling 6 DC 5V Connect to the power using power adapter Note For best results use HDMI cable and RG6 Quad Shielded antenna cabling 2 3 Remote Control Unit RCU You can control this receiver by this remote controller with full function 1 POWER Switch between operation and standby modes 2 MUTE Mute audio 3 gt Play Pause 4 USB m enter USB menu stop function 5 Record 6 INFO Display the programme information 7 144 PP 1 Previous Next 8 AA Rewind 9 PP Fast forward 10 SUB Display the subtitle language list 11 Recall Show the previous viewed channels list or switch to previously viewed channels 12 4 Change channels 13 OK Confirm the selected operation or display the channel list while watching a programme 14 Change volume 15 MENU Activate main menu or exit to live channel 16 EXIT Exit current menu step by step 17 VOL Change volume 18 EPG Electronic Program Guide Display the programme guide 19 Timer Setup event timer timer recordings 20 CH CH Change channels 21 NUME
14. rmation You can view the program information by pressing the INFO button while watching a program 8 8 EPG Information Press the INFO button twice to view detailed EPG information press the VOL VOL to switch current and next and press the INFO button once more to hide the detailed EPG information 9 Channel List This chapter will help you manipulate the channel list 9 1 OK List 1 Press the OK button to enter the channel list while watching a program 2 3 4 Press the YELLOW button to select channels by a z press the RED button to sort the channels Press the GREEN button can select the channels by frequency 19 5 Press the BLUE button can help you find the channel quick by the first character of name 6 press the lt gt button to change the channels list FTA CAS HD 9 2 Favorite List 1 If you have set several favorite lists press the FAV button to enter the favorite list 2 Press the lt gt button to change different favorite list and press the OK button can select to program in current favourite list 10 USB Control 10 1 Recording and Timeshift 10 1 1 Recording You can watch another channel from the same frequency while recording At the same time you can record two channels in the same frequency You can also do many operations while recording 10 2 PVR List You can enter the PVR list directly and then play the PVR file In the PVR list you also can delete the PVR files
15. the receiver by a soft cloth or mild solution of washing up liquid no solvents Connection Disconnect the receiver from the mains when you connect it to ANT or disconnect it from ANT Failure would possibly cause damage to the ANT Location Put the receiver indoor in order to avoid lightening raining or sunlight Uncover Do not remove the cover to reduce the risk of electric shock Contact qualified and licensed service personnel to repair the receiver or contact your dealer Reference Auto Search Manual Search PAL NTSC Conversion True full Color 32 bits on screen display OSD 2 menu languages supported English and Thai Multi language audio supported Multi language DVB Subtitle output 7 days Electronic Program Guide EPG Teletext output through VBI and OSD USB 2 0 Interface Software update If new software becomes available for this model it can be dow nloaded from our website www strong com au and then placed onto a USB Plug in the USB into the USB port on the unit and then go to Menu gt System gt Software Update gt USB Upgrade Product Overview 2 1 Front Panel 1 USB2 0 One USB 2 0 Host Port 2 Power Signal light Power signal indicator 3 Display It displays channel information In standby mode it displays local time 4 Power button Switch between operation and standby modes 5 A Change channel in viewing mode and move the cursor up in menu mo
16. you to save or load all the data and settings 1 Menu gt EDIT CHANNAL gt User Channel List gt Save User Data 12 2 Menu gt EDIT CHANNEL gt User Channel List gt Load User Data 5 Settings 5 1 System Settings Menu gt SETTINGS gt System Settings Tip You can set all the settings here by pressing VOL VOL button 1 Menu Language Set the menu language 2 Audio Set the preferred audio language 3 Audio2 Set the sub prime audio language 4 Subtitle Language Set the subtitle language if available 5 Subtitle control Select ON to view subtitles or select OFF to disable them 6 EPG Language Set the EPG language 7 LCN LCN lock switch locks channels in logical channel number 8 Digital Audio If a channel has AC3 and PCM audio language at the same time when you select RAW it will set AC3 audio language as default output and when you select PCM it will set PCM audio language as default output automatically when you highlight the channel If you set OFF in the channel list when you highlight the channel you should press the OK button to play it 9 Auto Channel Selection If you set ON in the channel list will play automatically when you highlight the channel If you set OFF this function is not available 10 Auto Exit CH List If you set ON the channel list will disappear when you press OK on a Highlighted channel If you set OFF it will not 11 Source signal type Choice source signal type of T or
Download Pdf Manuals
Related Search