GSM IV Intelligen Intelligen Intelligent Wireless Burglar Alarm
Contents
1. Chapter 3 Programming code settings Remarks means one digit number 123456 is default password if user changed password then it will change 123456 into new password Below 0 5 programming code for basic control support call sms Replay record voice 1 0 Set arm disarm system 0 disarm arm eg sms 123456 1 0 the system disarm 2 O Siren control 0 close 1 open 3 O Monitor locale 0 close O open remarks under talking status only 44 0 Talking locale 0 close open remarks under talking status only 5 0 Relay control 0 disconnect connect Below 10 39 programming code sms only 10 User number The 1 sms receiver eg send message 1234564 10 13800138000 means set number 15905090000 to be the 1 sms receiver when alarm happen send message to this receiver number 11 User number The 2nd sms receiver 12 User number The 3rd sms receiver 13 User number The 4th sms receiver 14 User number The 5th sms receiver 15 User number The 1 call receiver eg send message 123456 15 138001380005 set number 15905090005 to be 1 call receive number when alarm happen call this receiver number 16 User number The 2nd call receiver 17 User number The 3rd call receiver 18 User number The 4th call receiver 12. 7 Install ready whole system status as below Wireless infrared sensor Wireless zone 00 Hall alarm normal zone voice alarm Wireless door sensor Zone 01 Hall alarm normal zone voice alarm Wireless gas sensor Zone 02 Gas alarm 24hr zone voice alarm Remote 1 Zone 03 Remote 1 24hr zone voice alarm Remote 2 Zone 04 Remote 2 24hr zone voice alarm Wired door sensor Zone 16 Strobe normal zone voice alarm open alarm 15905090000 Sms receiver 0 Send message out when alarm happen 15905090001 Call receiver 0 Call out when alarm happen 3 System Test 1 System alarm test Press set button of remote then status be green light then depart the two parts of wireless door sensor result siren alarm out send message to message receiver number content door alarm Make call to call receiver number when receiver answer the call it play the record voice press repeat press 1 0 to recall the system press 2 0 close the siren support call programming 1 code 1 5 2 Long distance system control Call the main machine after connect then heard 1 long sound of di press password end with Then heard a long sound of di password is correct user monitor control support programming code 1 5 if heard 2 sound di password is wrong enter password again it quit automatically if no correct password enter into within 30 secon
3. Arm Remote recall NINININ O o ol lo Remote emergency call 3 be WIRED ZONE 1 2 3 4 5 GND SIREN RELAY SPEAKER I5 I4 I3 I2 YVDAMD AOOAOOED W A 12V DC Siren 3x Each wired zone response time is 100ms Fr Relay closes 3min when Ft Each wired zone can set NO NC mode _
4. alarm zone sms only 66 O zone name O For wired alarm zone 16 l mode of alarm zone 2 zone name for message content 3 mode of act the wired alarm zone port lmode of alarm zone details in chapter 2 2 24 Hour zone 0 disable zone LJ 1 normal arm zone 2 zone name remarks within 12 Chinese words within 24 English words default wired alarm 3 mode of action 0 shorted open default 0 eg 123456 66 1 hal1 1 wired alarm zone 16 is normal zone voice alarm message content hall port is open 67 O zone name T1 For wired alarm zone 17 68 O zone name O For wired alarm zone 18 69 O1 zone name O0 For wired alarm zone 19 70 O zone nam 01 For wired alarm zone 20 Chapter 4 Install Examples 1 Hardware and system description Install a infrared sensor for hall a wireless door sensor for door a wired door sensor for strobe a smoker sensor 2 remote 1 sms receiver number 1380013800 a call receiver number 13800138001 remarks sms receiver send message to this receiver number when alarm out call receiver call this call receiver number when alarm out 2 Install processing 1 Install accessories with main machine Insert SIM card into card lock at back side of main machine remarks support gsm network SIM card connect with siren siren be away from m
5. recall system For recall system centre centre eg 123456 43 13800138003 set number 13800138003 to be recall system centre number When system is recalled call this number after 3 sound then be off line Below 50 65 programming code for wireless zone sms only 50 O zone name For alarm zone 00 l mode of alarm zone 2 zone name for message content lmode of alarm zone details in chapter 2 2 24 Hour zone 0 disable zone LJ 1 normal arm zone 2 zone name remarks within 12 Chinese words within 24 English words default wireless alarm eg 123456 50 1 door wireless zone 00 is normal zone voice alarm mode Message content is door 51 O zone name For alarm zone 01 52 O1 zone name For alarm zone 02 53 O0 zone name For alarm zone 03 54 01 zone name For alarm zone 04 55 00 zone name For alarm zone 05 56 0 zone name For alarm zone 06 57 O zone name For alarm zone 07 58 O zone name For alarm zone 08 59 0 zone name For alarm zone 09 60 O zone name For alarm zone 10 61 01 zone name For alarm zone 11 62 O1 zone name For alarm zone 12 63 O1 zone name For alarm zone 13 64 0 zone name For alarm zone 14 Hi HHHH 65 01 zone name For alarm zone 15 Below 66 70 programming code for wired
6. 9 User number The 5th call receiver 30 new password Change password eg send message 123456 30 123456 password change to be 123456 310 DOOO OOOOE Set arm disarm system at fixed time update system time eg 1234564314 update system time eg 123456 31 2200 0800 set arm at 22 00 disarm at 08 00 33 0 Relay connect or not when alarm happen 0 no yes default 1 39 0 Menu language 0 English Chinese default 0 English Below 40 50 settings for alarm centre sms only 40 message centre For message centre number 0 0 set arm dsiarm don t notice set arm dsiarm system notice default 0 eg 123456 40 13800138000 0 set number 13800138000 to be message number when alarm happen send message to this number Al tcall centre For call centre number 0 000 0 0 0 set arm dsiarm don t notice LI l set arm dsiarm system notice default 0 eg 123456 41 13800138001 1234 0 set number 13800138001 to be call centre number 1234 is main machine number set arm dsiarm system don t notice when alarm happen call this number and send DTMF message A2 set system For set system settings centre eg 1234564 42 13800138002 set number 15905091002 to be set system centre number When system is standby call this number after 3 sound then be off line 43
7. GSM IV Intelligent Wireless Burglar Alarm System User Manual Thanks for choosing our product please read th Chapter 1 Functions and 1 Main functions 1 Record 10 secs voice alarm message 2 Setting fixed time for set recall alarm sy 3 Main machine monitor talk funct main machine 4 Both 16 wireless alarm zone and 5 zone disabled zone to comply with 5 Wired alarm zone open close set e Outlet siren port detectors work with m uple learning code ichine from long distance umber and 1 group call alarm centre number s off elay outlet when alarm out to work together with power video etc ity dual or quad frequency GSM GPRS wireless industrial module backup battery in main machine er by sms when power eless system Install easily in garage storage where fixed line yy circuital current 20mA 2 Supply power DC 9V 12V 3 working temperature 10 C 55 C 4 Support GSM900 1800Mhz Optional 850 1900MHz 5 Receive mode ASK 6 Receive frequency 315 433 MHz 7 workable distance 100 m empty space Chapter 2 mode of alarm zone 1 mode of alarm zone remarks 00 15 wireless alarm zone 16 20 wired alarm zone For each alarm zone there are 3 kinds setting mode for different alarm message A Arm Zone only Active when the alarm in Arm mode B 24 Hour Zone will Active at all conditions even in Disarm mode C Disabled Zone Inactive Zone
8. ain machine at least 3m fix antenna power on 12V 1 5A power internal outside STATUS orange light flash slowly means it is searching network around 40 seconds later it turn to green light then take next step If can t turn to green light power off then check the sim card and antenna if ready 2 Comply with remote and sensors Put battery into wireless sensors and remote Press RESET for 2 seconds STATUS indicator turn to lasting red light main machine is learning sensors 20 seconds later sensors quit if can t receive signal from main machine Press RESET again to quit install wireless infrared sensor wireless door sensor wireless smoker sensor remote 1 and remote 2 one by one press emergency button of remote to comply with main machine STATUS indicator of main machine will flash if sensor or remote be read or try again 3 Record Press RECORD for 2 seconds RECORD light on main machine under record status for 10 seconds 10 seconds later it quit automatically speak with main machine to record till RECORD light off 4 Update system time Send message 123456 31 5 Zone settings details in chapter 2 and chapter 3 Send message 123456 50 1 hall alarm 123456 51 1 door alarm 123456 53 2 eas alarm 123456 54 2 remote 1 123456 55 2 remote 2 123456 66 1 strobe 1 6 Add user Send message password 10 13800138000 Send message password 15 13800138001
9. ds 3 Trouble shooting If siren keep silent please check if it is connected well or mode of zone set to be silent alarm If can t call out or send message out please check if the value of SIM card is too low or the signal is too weak Chapter 5 Common Operation Introduction How to add door sensor infrared sensor remote etc wireless detector Press RESET for 2 seconds STATUS indicator turn to lasting red light main machine is learning sensors 20 seconds later sensors quit if can t receive signal from main machine Press RESET again to quit the alarm zone number start from 00 then 01 02 To re arrange the zones O no jumper 1 High 2 LOW 1 DO D3 must be 0022 2 AQ A7 can be randomly e g you can assign 00012221 for zone 1 sensors you can assign 00012220 for zone 2 sensors you can assign 00012210 for zone 3 sensors 3 After setting the jumpers Please clear the main alarm all zone setiings by holding the reset button when powering on the main unit 4 then add the zone sensors by order after powering on the green led light up press the reset button for 2 sec Then e g Zone 1 Remote 1 by pressing emergency button Zone 2 Remote 2 by pressing emergency button Zone 3 trigger the door PIR zone 3 sensors Zone 4 trigger the door PR zone 4 sensors NSN then sensors will be recorded in order 2 How to delete wireless sensor remote Send message password 50 0 wireless detectors be d
10. elete of zone 00 3 How to revive to default settings Press RESET power on till SATUS red light turn to orange flash light all detectors of main machine be delete The password to be 123456 4 Long distance set the alarm system by phone Call the main machine heard a long sound of di Put password end with head a long sound of di put into 1 1 then a long sound di again then quit the call Remarks all call programming a long sound of di means successes 2 short di means failure 5 How to re define remote control pad Press RESET 5 seconds STATUS indicator light turn to red light then turn to orange light press the 4 button one by one the 1 one is emergency alarm button if ok the STATUS light will flash or it failed The 2 button is recall system button the 3 one is set outside the 4 one is set at home Then it quit remarks support 4 button remote only Chapter 6 Wireless accessories connection remarks high level 1 1 low level 2 no connection 0 For Sensors All Zone Jumpers DO D3 must be set to 0022 AO A7 can be randomly e g you can assign 00012221 for zone 1 sensors you can assign 00012220 for zone 2 sensors you can assign 00012210 for zone 3 sensors item 2262 chip data lead pin connection DO pin D1 pin D2 pin D3 pin 0 2 Door sensor Infrared sensor Gas sensor 0 0 a Smoker sensor 2 2 2 2 1 help Remote set
Download Pdf Manuals
Related Search