Quickstart - Overview US
Contents
1. 3 Menu page Microsoft Internet Explorer Fie Edt ieee Frahs Took Help Back x p F Search yr Fran ert amp 5 J las gt i iga esai S Go ea I don t see the built in web page Why 1 Do you have an Ethernet card installed in your computer and is it properly configured Refer to 3 2 of the Addendum document 2 Are the cables correctly connected Both the WAN and ET2 LEDS should be lit 3 Reboot your PC and try again 4 ls your PC and web browser properly configured Refer to 3 2 and 3 3 of the Addendum document 5 Do you run another DHCP Server on your LAN Refer to 3 2 1 of the Addendum document 6 Do you use Static IP addresses on your LAN Refer to 3 2 2 of the Addendum document Select operator 1 Click Login on the first page of the web interface as 2 Enter login admin password admin Operator itha w Change 3 Click Network on the main menu 4 Click Operator PPP and Keep alive al ot ee afi by 5 Select your operator from the list and click Change If your operator is not listed select Other and fill in operator network and ADSL settings manually ere METE 6 If you have received any service name user or Lis r wo AAA password from your operator enter them Prat manor a ere 7 Click Save Congratulations You are now connected to the Internet You can start surfing now You may for instance try surfing to www intertex se I don t see2. any web pages Why 1 Reboot your PC allowing it to get fresh configuration data from the ADSL Modem and try again 2 Is your firewall properly configured Press ALT CFG on your ADSL modem repeatedly until Hi is displayed 3 Test your Internet connection with the built in diagnostic test Refer to 3 4 of the Addendum document Did you select the right operator Refer to step C above Is your web browser properly configured Refer to 3 3 of the Addendum document Is your ADSL Modem properly configured Refer to 4 1 of the Addendum document 7 Have you used your Internet connection before with some other ADSL modem In that case unhook that ADSL modem and wait 3 hours before re connecting your ADSL Modem It may take such a long time before your ADSL supplier s cache entries expire Oak US ADSL VGW 1 2 Package Details The following items should be included in your box e Quickstart Overview this document e Addendum to the Quickstart Overview Sheet e X66 Internet Gate ADSL modem e 9 5 V DC power adaptor e DSL splitter ATF 021 e ADSL cable round e Phone cable flat e Ethernet cable e USB cable e Headset e Handset adaptor cable e USB driver diskette e Phone Y adaptor RJ11 e Wireless upgrade note If any of the items above are damaged or missing please contact your dealer Interface indicators On Interface is connected Off Interface is not used Flashing Data is sent or
3. received Wireless Bluetooth or 802 11b option Universal Serial Bus Ethernet PC or LAN Internet connection Flashing firewall stopped a packet Data is sent to the Internet Data is received from Internet ALT CFG Press to select firewall security profile Press to pick up hang up headset re UF ALTECFG TORE pi LAIT Ri SET Press once to see firmware version Press SELECT to change between display modes Hi Lo AC Firewall security level Keep pressed for 3 LQ Line Quality SNR margin seconds to enter set TS ADSL connection transmission speed up mode Read more RS ADSL connection reception speed about set up mode in the TS and RS only indicates the ADSL link physical speed Your Addendum document ADSL supplier may limit the actual transfer speed PHO HS Incoming call to telephone headset connected to SELECT EXP port Lift receiver or press ALT CFG to answer call Press to toggle displayed options RS TS Incoming outgoing call in progress on PHONE port Press and hold for 2 seconds to cancel any set up Read more about display in the Addendum document SIP or IP Telephone Client The headset or analogue telephone connected to the EXP port acts as a general SIP client You can configure the SIP client by surfing to the built in web pages and select Telephone Ports under the Configuration menu Using a headset you can also dial answer and hang up on thi
4. In most cases the A B C steps on this page will get your ADSL modem up and running If you run into problems you find the solution to the most common problems in the Addendum document Hook up the Cables Note Make sure your computer is turned off 1 Connect the supplied Ethernet cable between port ET2 on the rear of the ADSL modem and the Ethernet port on your computer 2 Connect all cables as shown in the diagram below Make sure you use the supplied round ADSL cable between the splitter and the LINE port 3 Connect the power adaptor and push the ON switch on the rear of the modem Use RJ11 Y adaptor to optionally connect phones to old analog telephone line Not included Phone cable flat ee fol LLELE Handset yy E adaptor es va LINE PHONE For information about how to connect a LAN see 3 1 in the Addendum document Read more about your ADSL modem in the always up to date online user manual You access it by clicking on Online User Manual on the first page on the ADSL modems web configuration pages or directly at www igmanual com Surf into your ADSL modem 1 Wait until the ADSL Modem has established a connection indicated by the WAN LED being lit This might take a couple of minutes 2 Turn your PC on and start your web browser i e Netscape or Internet Explorer 3 Surf to your ADSL Modem by typing its default IP Address 192 168 0 1
5. one cable FXS port line to FXO port You can connect the supplied headset to this port and use it to make and receive SIP calls You can connect a line to the telephone network to this port to allow your SIP phones to make and receive ordinary Or you can connect an ordinary telephone telephone calls through this local to it using the telephone adaptor cable The gateway connected telephone will then become a SIP IP phone
6. s page Pressing the ATL CFG key will also answer and hang up The default SIP user name is hsphone and it is registered to the internal SIP server of the Internet Gate if not changed to a full SIP address like yourname yoursipprovider com With the default configuration you can directly use this SIP client to place SIP calls SIP PSTN Gateway The telephone line connected to the FXO port of the Internet Gate acts as a gateway between SIP and the ordinary telephone network PSTN You can configure the gateway by surfing to the built in web pages and select Telephone Ports under the Configuration menu The default SIP domain name for the gateway is localgw and can be used with the SIP Switch software addition By default just dialling lt telephone number gt from any client using the product will use this gateway port to reach ordinary telephones With the default configuration incoming calls on the telephone line will be forwarded to the SIP client connected to the EXP port ET2 LINE Ethernet port to Port to connect PC SIP USB Port to connect a PC without a WIRELESS optional Read the wireless upgrade note about how to connect ADSL network card phone or local area signal cable network LAN install a wireless card creating a ON DC USB ET2 EF EXP LINE PHONE wireless access a id EXP PHONE Port to connect headset or telephone adaptor Port to connect an ordinary teleph
Download Pdf Manuals
Related Search