User manual Arc Control 1
Contents
1. ANOLIS ArcControl 1 USER MANUAL ArcControl 1 Table of contents 1 Introduction 2 INSTAMatioNS 00 21 MOI ar dada O PE AA 2 3 Single installation with the ArcPower drivers a 2 4 Multiple installation with the ArcPower drivers 3 Operation AT TT 4 Technical Specificati nS 1 Introduction The ArcControl 1 is the perfect solution to provide the user control of installed Anolis LED light fittings This slim line LED control panel allows to dim LED light fixtures set desired colours and run built in programs The ArcControl 1 should be installed with Anolis ArcPower driver s 2 Installation 2 1 Mounting The ArcControl 1 control panel is designed for wall mounting into KU 68 universal box To install the ArcControl 1 1 Prepare the wall by drilling the necessary holes fitting the KU 68 universal box and cables 2 Attach the DMX output and power wires to the terminal blocks being careful to observe the correct polarity 3 Screw the metal frame plastic frame to the KU 68 universal box 4 Snap the ArcSource 1 panel to the plastic frame ArcControl 1 i OY Screws aa anes box KU 68 2 2 Wiring Figure below shows the DMX output termi2. ddress at 5 2 Set RGB or RGBW mode along according to used LED fittings See DMX chart of respective ArcPower driver Usually it is mode 1 and 2 AP driver menu path 5 3 Set Dynet mode in the menu Protocol AP driver menu path SPE Prt din Note GND terminals interconnected on PCB printed circuit board TRA 8 7 6 2 DMX input of ArcPower driver 2 4 Multiple installation with the ArcPower drivers If you need to control the ArcPower driver s from several places simultaneously you can use more ArcControl s 1 connected in parallel In this case the following changes has to be made 1 ArcCotrol 1 two pads marked J1 must be interconnected 2 ArcPower driver Set dynet mode in the menu Protocol AP driver menu path SPE Prt din Interconnect the pads 8 7 6 2 DMX input of ArcPower driver if multi fixture operation is required Example of wiring iee F SV2 EI N SV2 SE A svi SEI Svi SEI 21 287 6 DMX input of ArcPower driver 3 Operation The ArcControl 1 uses 12 control buttons for setting desired colour dimmer level and program selection Description of function of each button Button ArcControl 1 ON ArcControl 1 OFF RED GREEN BLUE CYAN Switches
3. nals P1 on the unit and two supply terminals SV1 SV2 The input SV1 or SV2 has to be connected to a 12 V DC supply Pi GND Signal Signal Signal Signal GND SV2 oo 1 SV1 oo 8 11 Connectors DMX and supply wires are connected to the self locking terminals PHOENIX located on the PCB of the ArcControl 1 Insert each wire directly to the circular hole of the terminal and check its fixation To release the wire insert appropriate tool narrow flat tip screwdriver to small rectangle terminal hole and the wire will be released 2 3 Single installation with the ArcPower drivers The ArcPower drivers offer 12 V at DMX input connector pin 2 which can be used for supply of the ArcCo ntrol 1 unit RJ45 socket for DMX IN Front view of the socket Pin 1 Not connected Pin 5 Not connected Pin 2 12V Pin 3 Not connected Pin 7 Data Pin 4 Not connected Pin 8 GND Pin 6 Data Owing to this feature you can use only one cable for DMX connection and power supply Use a suitable cable with 2 twisted pair of conductors and connect pins 2 6 7 8 of DMX input of the ArcPower driver ArcPower driver setting 1 Set ArcPower driver to DMX address 1 If you use two or more drivers set all DMX addresses at 1 Note If you use single colour LED fittings set ArcPower SmartWhite driver DMX a
4. to desired colour Turns on desired colour MAG Adj j Adj is kept Note Adjusted dimmer level is kept Note Adjusted dimmer level is kep Switches to white colour Turns on white colour Note Dimmer level maximum Note Dimmer level maximum Dimmer up Switches to last state Dimmer down Switches to last state Note Dimmer minimum both buttons Program running slow colour chan Program running slow colour chan ging Red gt Green gt Blue ging Red gt Green gt Blue Program running fast colour chan Program running fast colour chan ging Red gt Blue gt Green ging Red gt Blue gt Green Switches OFF the ArcControl 1 Switches ON the ArcControl 1 to the last colour 4 Technical Specifications Input voltage 12VDC Input current 15mA Compatible drivers ArcPower 36 ArcPower 72 ArcPower 144 ArcPower 360 and their K2 variants Dimensions ArcControl 1 i f ES LE Ls n 80 5 j KS RED GREEN BLUE CYAN AREA O _ AS VOBY ONOFF z Universal box KU 68 D 72 43 Included items 1 x ArcControl 1 1 x Universal box KU 68 accessories 1 x User manual Specifications are subject to change without notice January 7 2014
Download Pdf Manuals
Related Search