TFT-LCD TV MONITOR V200T USER`S MANUAL
Contents
1. Disconnect the power plug from the AC outlet if you will not use it for an extended period of time Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage points or other risks Do not touch the screen directly with your fingers You may damage the screen and oil from your skin is difficult to remove Do not apply pressure to screen The LCD is very delicate 2 Power Usethe type of power indicated on label 3 Plugs Do not remove any of the prongs of the monitor s three pronged power plug Disconnect the power plug from the AC outlet under following conditions If you will not use it for an extended period time When the power cord or plug is damaged or frayed gt If the product does not operate normally when the operating instructions are followed Adjust only those controls that are covered by the operating instructions Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician gt If the product exhibits a distinct change in performance service may be required Page 5 4 Power and extension cords Do not allow anything to rest on the power cord Do not locate this product where persons will walk on the cord Use the proper power cord with correct attachment plug type If the power source is 120V AC use a power cord that has UL and C UL approvals If t2. wW ViewEra TFT LCD TV MONITOR V200T USER S MANUAL WWW Vlewera com Rev 1 1 Page 1 Content 1 e AM WwW Introduction Product DESCHIDUOM ee an aaa Packase CODES vs obest d Vaiatu cie ied benda Product iius itur D ba ee i had Screen Cleaning Techniques s tta kase da Control Functions Front Panel Controls ccc cece cece eren Product Specifications Display MOS ceto PEE kka Pad Dead pixel Warranty and Service Information 10 Windows Setup 11 Wall Mount Installation Page 2 1 Introduction 1 1 Product Description Congratulations on your purchasing ViewEra LCD monitor It incorporates high quality display into a small light weighted module It has power saving capabilities and emits no radiation You will certainly benefit from this monitor in lots of ways to name some of them comfort safety and environmental protection This LCD monitor incorporates 20 1 color active matrix thin film transistor TFT liquid crystal display to provide superior display performance Its maximum resolution of 20 1 SVGA 800x600 is ideal for displaying complex graphics and high definition images Its other outstanding capabilities include audio system and OSD On Screen Display controls 1 2 Package Contents Included with your LCD monitor as follow
3. Please follow the mstruction below to properly connect the LCD monitor to external electrical source 1 Connect the female end of the power cable to the transformer Connect the male end of the power cable to the wall outlet or extension cable 2 Connect the cable from the other end of the transformer to the LCD monitor located at the back near the VGA signal cable Signal Connection 1 Power off both the LCD monitor and PC system before connecting them 2 Take out the VGA cable from the box then connect it to the signal connector at the back of the LCD monitor 3 Connect the other end to the VGA connector on the back of the PC system 4 Please make sure the connections to both the PC system unit and the LCD monitor is strong and secure Please don t forget to tighten the screws on each connector end Now turn on both the PC system unit and the LCD monitor After you finish setting up the LCD monitor please set the refresh rate to 75Hz 7 After setting up the LCD monitor please perform Auto Adjust in OSD so that the LCD monitor will be automatically set to optimal color display each time QN CA Please note When you disconnect any power cable or signal cable please do not pull the cable by grabbing the cable body Please grab the cable connector itself whenever you try to pull the cable during disconnect Page 17 5 Viewing Angles Tilting For better viewing angle you may tilt the LCD monitor forwards up to 10 d
4. 48 077 72 188 72188 4 640x480 37500 75 000 9 800x600 46875 75 000 5 720x400 31469 70087 0 8 Dead Pixel Policy Dead pixels on the TFT LCD panel are sometimes inevitable ViewEra guarantees that the monitor will be repaired or replaced if the number of dead pixels on our monitor exceeds the acceptable level The standard acceptable level is to have the maximum of 5 dead pixels on a TFT LCD panel 9 Warranty and Service Information Warranty The ViewEra TFT LCD TV monitors are warranted for one year parts and labor ONE and back light from the date of purchase Service 1 Please contact your ViewEra dealer for warranty service 2 For out of warranty service you may contact either ViewEra dealers or ViewEra Page 20 10 Windows setup For the best view please set up with the monitor type in Windows Please select as follows Control Panel gt Monitor gt Setting gt Advance gt Monitor gt Change gt Show all List gt Stand gt 20 1 For 800 x 600 please set to SVGA 800x600 60 75Hz Option Tuner setup 60Hz Theme Desktop SaesnSaver Appeatanse 5 E LE Dipa Adanler 5ng 3 Gere Adapter Merecr Ticubeshos Managemen Adaoler ype Tadent Video amp czeletato Blaze 30 PicMacia Pronebes p daslet Chip List All Modes DAC Tipe List of valid moces 1280 by 1024 True Color
5. 16 bit 75 LTertz Bn 640 by 480 True Color 32 bit 60 Ilertz 640 by 480 True Color 32 bit 75 ert Memo 372 Pug and Pay Mondor cn Tederi Video Biss lnlor akcr Screan resolution Color quahty en P E pm sd More ENT y 600 True Color it 75 mt hes x 1024 by 768 Truc Color 32 bit 60 Hertz 10t by 78 poe 1024 by 768 Trac Color 32 bit 75 1280 by 1024 True Color 32 bit 60 TTertz 1280 by 1024 True Color 32 bit 75 Troublesecot Lat Al Modes Page 21 11 Wall Mount Installation 11 1 Remove the Base by un installing the 4 screws and pull the Base from the Monitor 11 2 Install the Wall mount kit by securing the 4 screws with the bracket pointing in downward direction as shown in the picture 11 3 Face the Wall mount metal bracket in accordance with the direction shown for proper mounting with the monitor Page 22
6. GB c 4 VOLUME X MUTE gt RESET INPUT 1280X1024 H64 0KHZ V60 0 HZ Tools Menu Volume Mute Reset Input Adjust the volume using and buttons Mute function Reset function PC AV S Video Y Cb Cr selection Page 10 gt EXIT OSD LANGUAGE 1280X1024 H64 0KHZ V60 0 HZ OSD Function Selection Menu Exit OSD Exit the OSD function selection menu OSD H Position Pressing moves the OSD to right Pressing moves the OSD menu to left OSD V Position Pressing moves the OSD menu upward Pressing moves the OSD menu downward OSD DURATION Set the OSD display time LANGUAGE Set the OSD display language Page 11 2 2 Control Button Front View AV gt Mode amp y Cw 45 D 5 45 G5 09 12 3 4 5 6 7 8 1 Source Select Direct select the input signal PC Pressing this button pops up S Video YCbCr the OSD menu on the screen gt NO Function And used to select the OSD i m control options on the screen 3 NO Function 4 OSD menu select 5 Adjust decrease This button is used to decrease the value of selected function 6 Adjust increase This button is used to increase the value of selected function 7 Mute This button is used to mute speaker volume 8 Power Switch Power switch Page 12 9 BRIGHTNESS CONTRAST SATURATION TINT SHARPNESS Monit
7. Pressing this button pops up the OSD menu on the screen Add used to select the OSD control options on the screen S Adjust decrease This button is used to adjust the decreasing value of selected 6 Adjust increase This button is used to adjust the increasing value of selected 7 Mute This button is used to volume Mute 8 Power Switch Power switch Page 7 LE E mg d F8 24 c AUTO ADJUST BRIGHTNESS CONTRAST CLOCK PHASE H POSITION V POSITION EI 1280X1024 H64 0KHZ V60 0 HZ Monitor Function Selection Menu Auto Select this function to obtain the best display efficiency Brightness Adjust the brightness using and button Contrast Adjust the contrast using and buttons Clock Adjust the clock using and buttons Phase Adjust the phase using and buttons Horizontal Pressing moves the display image to Position right Pressing moves the display image to left Vertical Pressing moves the display image upward Position Pressing moves the display image down ward Page 8 F9 j 24 RGB os COLOR TEMP RED GREEN BLUE 1280X1024 H64 0KHZ V60 0 HZ Ree Color Temperature and RGB Adjusting Menu Color Color Temperature Select Temperature GR Red Red range adjustment era Green Green range adjustment GB Blue Blue range adjustment Page 9 I i e B Fe 24 R
8. egrees or backwards up to 25 degrees Down 10 Up 25 Page 18 6 Product Specifications 20 1 Product Specification AV 0 LCD Displa 1xel Pitch 20 1 Active matrix TFT LCD panel 0 51 H x 0 51 V mm 800 H x 600 V SVGA Resolution et Size ack Size Contrast Ratio 500 1 ishtness 500 cd m Response Tr 6 ms Tf 16ms typ Time Display Color 16 777M View Angle L R 80 U D 60 C Interface RGB analog 0 7V peak to peak Video Sync TTL positive or negative Display Mode SVGA PC Audio in RCA JACK R L Audio out Phone Jack Video RCA Jack Mini Dine Connector requenc Signal Connector 595 H x 430 W x 190 D mm 695 H x 675 W x 275 D mm Hor 31 5 48KHz Ver 56 75Hz D sub 15 pin Source select CH down CH up Menu Adjust Mute Power OSD Menu Contrast Brightness Auto Adjust Clock Phase H Position V Position Power AC Input 100 240V 1 8A 50 60Hz Adapter DC Output 12V 5 0A Operating Temperature 0C 40 C Conditions Humidity 20 85 Storage Temperature 20 60 C Conditions Humidity 10 95 BSMI FCC DOC CE B UL TUV GS Net 8 5Kgs Gross 14Kgs C T1 T1 5 UJ Jio cen C A E 5 Q v r ret G Q 3 5 Weight Page 19 7 Display Modes ET ad E kHz Hz kHz Hz 1 31469 70070 6 800x600 35 156 36 250 3 37861 72309 8 800x600
9. he power source is a 240V AC supply use the tandem T blade type attachment plug with ground conductor power cord that meets the respective European country s safety regulations such as VDE for Germany Do not over load wall outlets or power cords Ensure that the total of all units plugged into the wall outlet does not exceed 10 amperes Ensure that the total ampere ratings on all units plugged into the extension cord is not above the cord s rating If the power supply cord which came with your monitor is to be connected to the PC instead of the wall outlet Use an UL TUV approved computers with receptacle rated 100 240V AC 50 60Hz 1 0AGminimum only 5 Environment Place the monitor on a flat and leveled surface Place the monitor in a well Ventilated place Keep the monitor away from Overly hot cold or humid places places directly under sunlight dusty surroundings equipment that generate strong magnetic fields Please adjust the frequency to 75 Hz after setting up the LCD monitor Then push the OSD menu button and use the Auto Adjust function to find the best mode of your computer Page 6 2 Control Functions 2 1 Control Button Front View PC Mode 45 D 5 G6 0 12 3 4 5 6 7 8 pd Source Select Direct select the input signal PC AV S Video YCbCr 2 NO Function 3 Auto Adjust Adjust CLK Phase H V Position automatically 4 OSD menu select
10. ing items 1 20 1 TFT LCD monitor User s manual Remote control 2 15 pin D sub signal cable 3 Line Sound Card Cable 4 AC power cable 5 Adaptor 6 T Page 3 1 3 Product Features 1 High contrast color TFT LCD display support resolution up to 20 1 SVGA 800 x600975Hz Compatible with IBM VGA IBM SVGA and Macintosh standards Imbedded audio system provides sound performance AV In and S video Component Option Power management system conforms to VESA DPMS standard Support DDC 1 2B for Plug amp Play compatibility Advanced OSD control for picture quality adjustment Detachable stand for wall mounting application 90 1 ta 5 1 4 Screen cleaning techniques 1 Gently clean the screen with a clean camel hair lens brush or a soft clean lint free cloth to remove dust and other particles that can scratch the screen Do not apply pressure to the screen surface when wiping it clean 3 Do not pour or spray any liquid directly onto the screen or casing Chemical cleaners have been reported to damage the screen or case of the LCD monitor Page 4 1 5 Additional Read all of these instructions and save them for later use Follow all warnings and instructions on the product 1 Product Do not cover block the vent holes in the case Do not insert sharp objects or spill liquid into the LCD monitor through cabinet slots They may cause accident fire electric shock or failure
11. or Function Selection Menu Brightness Q Contrast Saturation A TINT 9 Sharpness Adjust the brightness using and button Adjust the contrast using and buttons Adjust the Saturation using and buttons Adjust the Tint using and buttons Adjust the Sharpness using and buttons Page 13 INPUT Tools Menu x n Volume Adjust the volume using and buttons Mute Mute function Reset Reset function Input PC AV S Video YCbCr select s Page 14 EXIT OSD OSD H POSITION LANGUAGE 050 OSD Function Selection Menu Exit OSD tp OSD H Position Ej OSD V Position X OSD DURATION amp LANGUAGE Exit the OSD function selection menu Pressing moves the OSD to right Pressing moves the OSD menu to left Pressing moves the OSD menu upwards Pressing moves the OSD menu downwards Set the OSD display time Set the OSD display language Page 15 3 Inputs Diagram Inputs AV 1 2 3 4 6 7 9 1 DC IN DC power input from adaptor 2 AV IN RCA jack AV signal input 3 S VIDEO IN S Video signal input 4 LINE OUT Sound signal output Stereo Phone Jack 5 RCA JACK Audio signal R L input AUDIO IN 6 VGA IN PC IN Connect to PC VGA D Sub signal 7 Component IN Component in Y Cb Cr Page 16 4 Setup Electrical Connection
Download Pdf Manuals
Related Search