User`s manual 2013
Contents
1. U B IR EVENT To connect the controller to the power mains follow the wiring connection diagram Fig 3 Connection sequence CONNECTION TO POWER MAINS Remove the decorative front panel and the base Fig A and B Route the wires through the ports 2 6 in the controller casing Strip the wire ends 7 8 mm long Connect the wires to terminal blocks 8 and 9 Fig 2 according to the wiring connection diagram Fig 3 Secure the wires with clamps 1 and 5 Fig 2 Re install the base and the decorative front panel B fan S controller The controller starts operation immediately upon supplying the power voltage to its input If the appliance fails to operate refer to Table 1 for troubleshooting TYPICAL FAULTS AND FAULT FAULT PROBABLE REASON FAULT HANDLING WASTE Check the appliance connection Limited or see Connection to power mains The appliance fails no power supply and ensure secure contact on the to operate terminal blocks Blown fuse Replace the fuse TABLE 1 OVIT USE DELIVERY SET DESIGNATION KEY MAIN TECHNICAL DATA UBER RS thyristor speed regulator SR hereinafter the controller is designed for continuo2. S external switch The control unit starts operation immediately upon supplying the power voltage to its TYPICAL FAULTS input If the appliance fails to operate refer to Table 4 for troubleshooting AND FAULT HANDLING FAULT PROBABLE REASON FAULT HANDLING Check the appliance connection The appliance fails Limited or see Connection to power mains to operate no power supply and ensure secure contact on the terminal blocks TABLE 4 D OVET U B IR WALL SURFACE MOUNTING U IR DOY NIT WALL FLUSH MOUNTING NDA MANUFACTURER S WARRANTY UBR The fan is manufactured at the factory of Ventilation systems PrJSC hereinafter referred to as the Manufacturer By purchasing this product the customer confirms to have read and agreed to the terms rules and requirements related to operation storage transportation mounting adjustment connection maintenance and repair as well as warranty obligations with respect to this product as set forth in the manufacturer s accompanying documentation to the product The manufacturing company sets forth the warranty period service life of the product as 12 months following the sale date via retail network subject to the customer s ensuring compliance with the rules of transportation st
3. Route the wires through the ports 2 6 in the controller casing Strip the wire ends 7 8 mm long Connect the wires to terminal blocks 8 and 9 Fig 2 according to the wiring connection diagram Fig 3 Secure the wires with clamps 1 and 5 Fig 2 Re install the base and the decorative front panel B fan S controller On the initial start set up the minimum speed of the connected fan To set the minimum rotation speed set the control knob 1 Fig 4 on the front panel to the leftmost position and then gently rotate the control knob of potentiometer 5 Fig 5 with the plastic screwdriver included into the delivery to the right or to the left until the fan starts rotating steadily UBR The controller starts operation immediately upon supplying the power voltage to its input If the appliance fails to operate refer to Table 2 for troubleshooting FAULT PROBABLE REASON FAULT HANDLING The appliance fails to operate Limited or no power supply Check the appliance connection see Connection to power mains and ensure secure contact on the terminal blocks Blown fuse Replace the fuse TABLE 2 GWIW ENTT TVPICAL FAULTS AND FAULT HANDLING OVITE USE DELIVERY SET DESIGNATION KEY MAIN TECHNICAL DATA UIBIR The fan speed switch hereinafter referred as the switch is designed for control of the rotation speed of multi speed fans The deli
4. User s manual 2013 DVS CONTENTS Introduction Safety requirements Operating requirements Mounting Maintenance Transportation and storage rd o speed controller RSA se Delivery Set Main technical data Description and design Connection to power mains Typical faults and fault handling Speed controller RS Delivery Set Main technical data Designation key Main technical data Description and design Connection to power mains Minimum speed setting Typical faults and fault handling Fan speed switch P Use Delivery Set Designation key Main technical data Description and design Connection to power mains Tvpical faults and fault handling Timer T Use Delivery Set Designation key Main technical data Description and design Connection to power mains Typical faults and fault handling Wall surface mounting procedure Wall flush mounting procedure Manufacturer s warranty Acceptance certificate Warranty card 01 ZU OoOoo00 DODODO DODODOODO OoOooo00 OoOooOO Dooooo0 PPPPRWW A Y 01010101 a ee ee ee ee er Si etek Seek 00000 ONN 0 OWHOWWH ARONNNN 00 NNNANNN U IR QY VETS The present operation manual consisting of the technical details operating instructions b er l INTRODUCTION and technical specification applies to the control unit enclosed in a versatile casing UBR and covers its installation as well as the regulations and warnings required for correct
5. and safe operation of the product Disconnect the product from the power mains prior to all operations specific to en connection setup maintenance and repair The power mains connection must be performed by qualified personnel with valid permit for unassisted operations with electrical installations up to 1000 V after careful reading of the present operation manual The single phase mains which the product is to connected to shall be compliant with the standing regulations The stationary wiring shall be equipped with an automatic circuit breaker Connect the product to power mains through QF circuit breaker integrated into the stationary wiring with the contact gap on all poles at least 3 mm Prior to connecting the unit to the power mains check it for visible damage as well as for any foreign objects in the unit casing REQUIREMENTS RESTRICTIONS The controller may only be used as intended No modifications or alterations are allowed Do not use the controller if the ambient air contains explosive or corrosive substances Avoid moisture and splashes on the controller casing Do not block the vents in the casing Do not position the controller close to heating appliances The product is not to be used by children and persons with reduced physical mental or sensory capacities without proper practical experience or expertise unless they are controlled or instructed on the product operation by the person s responsible for
6. their safety Do not leave children unattended and do not let them play with the product Do not sit on the product and do not put objects on it Fulfil the requirements stated in this user s manual to ensure long service life of the product GWI ENTS OPERATION REQUIREMENTS MOUNTING MAINTENANCE TRANSPORTATION AND STORAGE UBR The product is rated for connection to single phase AC 220 240 V 50 Hz power mains Ingress protection rating against access to hazardous parts and water ingress IP30 The product is rated for operation at the ambient temperature ranging from 1 C up to 45 C The product is classified as Class II electric appliance Both wall surface and flush mounting options are possible depending on the controller type The controller is mounted using the screws and dowels included in the delivery set The wall surface mounting sequence is shown in Fig A F Page 20 The wall flush mounting sequence is shown in Fig G M Page 21 22 Clean the product from any dust and dirt which may accumulate on the surfaces Power off the product before performing any maintenance operations For cleaning use a soft cloth and a brush soaked in an water detergent solution Avoid any liquid on the electrical components Wipe the cleaned surfaces dry Transportation of the product with any vehicle is allowed The unit must be stored in the original packing at ambient air temperatures from 5 C to 40 C at relative air
7. to the product in case of force majeure fire flood earthquake war hostilities of any kind blockade in case of absent seals provided such seals are prescribed by the User Manual or other relevant substituting document in case of unavailable warranty card in case of unavailable payment document to confirm the purchase with indication of the sale date The manufacturing company shall be responsible for defects arising through its fault prior to the moment of transferring the product to the ownership of the customer The manufacturing company shall not be responsible for defects arising after transferring the product to the customer and caused by the customer s violating the rules of transportation storage assembly and operation of the product or by actions of third persons an accident or force majeure circumstances The manufacturing company shall not be responsible for damage to health and property of the customer caused by the customer s violating the User Manual or other relevant substituting document other use of the product by the customer other than its intended use or by failure of the customer to comply with warnings and other information on the product specified in the User Manual or other relevant substituting document or by the customer s violating the rules of transportation storage mounting maintenance and operation of the product UBR Autotransformer speed controller Thyristor speed controller Fa
8. he control voltage is off or after the lighting intensity falls below the set point the control unit continues to supply power to the fan within the time period set by the timer 2 30 min Timer with motion sensor TP The control unit supplies voltage to the connected fan after the external switch e g the light switch supplies control signal to the input terminal LT or in case of motion detection ata distance from 1 to 4 m and the horizontal viewing angle of 100 After the control voltage is off or after no more motion is detected the control unit continues to supply power to the fan within the time period set by the timer 2 30 min The off delay time humidity and lighting set point are regulated with the control knobs on the front panel AVENT OPERATION MODES AND INDICATION UBR The control unit has three operation modes 1 Standby mode the control unit operation mode in case of no signals from the sensor or the external swath The fan is off The operation lamp blinks once in 5 seconds 2 Active mode the operation mode is activated by the motion sensor external swath closing exceeding humidity or illumination set point The fan operates The operating lamp has permanent glow 3 Timer operation the control unit operation mode that is activated in case of no motion detection external switch opening humidity or illumination decrease below the set point The runout time is individually adjustable T
9. he fan runs The operating lamp blinks once in 1 second The control unit has the connected load monitoring function 1 In case of the regular current load up to 1 5 A the operating lamp is green 2 In case of the load current from 1 5 A up to 1 9 A the operating lamp is red This current load leads to heavy duty operation conditions The control unit operates at increased load which may result decreased service life of the appliance It is recommended to reduce the connected load below 1 5 A 3 In case of the load current above 1 9 A the operating lamp blinks red 5 times in second That is an emergency operation mode The load is disconnected automatically To revert to the standard operation mode disconnect the control unit from power mains at least for 10 seconds and connect the fan with the current consumption below 1 5 A U IR OVINTE To connect the speed switch to the power mains follow the wiring connection diagram Fig 12 Connection sequence Remove the decorative front panel and the base Fig A and B Route the wires through the ports in the control unit casing Strip the wire ends 7 8 mm long Connect the wires to terminal blocks 1 2 Fig 11 according to the wiring connection diagram Fig 12 Re install the base and the decorative front panel CONNECTION TO POWER MAINS 1 Input terminal block 3 Fe ji u Output terminal block 3 timer circuit board
10. humidity not more than 80 The storage environment must be free from dust and corrosive acid or alkaline vapours Recycle at the end of the service life Do not dispose the product with unsorted municipal trash UBR RSA 0 3 autotransformer speed controller hereinafter the controller is designed for stepping the fan speed up or down by fluctuating the fan input voltage The delivery set includes Controller 1 item Self tapping screws with dowels 2 sets Spare fuse 0 4 A 250 V 1 item User s manual Packing box O hon Input voltage 50 Hz V 220 240 Output voltage V 230 200 180 160 Max output power VA 60 Max load current A 0 3 Dimensions mm 162x80x70 Weight g 650 The controller front panel is shown on fig 1 The control knob position corresponds to the fan rotation speed The control internal design is shown on fig 2 EAN MENTE USE DELIVERY SET MAIN TECHNICAL DATA DESCRIPTION AND DESIGN Das UBR 1 Speed control knob 2 Operation lamp 3 Switch 1 Output wire clamp 2 Output wire port 3 Mounting holes 4 Autotransformer 5 Input wire clamp 6 Input wire port 7 0 4 A 250 V fuse 8 Output terminal block 9 Input terminal block
11. n speed switch Control unit is recognized as serviceable Approval mark Manufacturing date RSA 0 3 RS 1N RS 1V RS 1 5N RS 1 5V RS 2N RS 2V RS 2 5N RS 2 5V P2 5 0N P2 5 0V P3 5 0N P3 5 0V P5 5 0N P5 5 0V T 1 5N T 1 5V TH 1 5N TH 1 5V TF 1 5N TF 1 5V TP 1 5N TP 1 5V mark the proper model Sold name and stamp of the trade company Date of sale EVENT ACCEPTANCE CERTIFICATE NDA WARRANTY CARD V35EN 03
12. orage mounting and operation of the product In case of any malfunction of the product through the fault of the Manufacturing company within the warranty period service life the customer shall have the right to elimination of the manufacturing defects by means of warranty servicing performed free of charge The warranty servicing implies performance of activities related to elimination of defects in the product aimed to provide intended use of the product by the customer The defects are eliminated either by replacing or repairing such a product or a part Component thereof U IR OVITE NOTE with the purpose of performing warranty servicing you please produce User Manual or other relevant substituting document and the payment document as an evidence of the purchase with indication of the sale date The product model shall comply with that one specified in the User Manual or other relevant substituting document With the purpose of performing warranty servicing please contact the trade company where you purchased the product If warranty servicing on the spot proves impossible you will be provided with the necessary information regarding rendering of this service Manufacturer s warranty shall not apply in the following cases in case the customer fails to provide the product in complete according to the package contents specified in the User Manual or other relevant substituting document including any components disassembled by the c
13. s to terminal blocks according to the wiring connection diagram Fig 9 Re install the base and the decorative front panel B fan S switch The switch starts operation immediately upon supplying the power voltage to its input F the appliance fails to operate refer to Table 3 for troubleshooting nen HANDLING FAULT PROBABLE REASON FAULT HANDLING 7 l Check the appliance connection The appliance fails Limited or see Connection to power mains to operate no power supply and ensure secure contact on the terminal blocks TABLE 3 UBR avers The timer in the versatile casing is designed for the fan control depending on humidity and light conditions actuation of the external switch or motion registration USE The delivery set includes DELIVERY SET 1 Controller 1 item 2 Self tapping screws with dowels 2 sets for wall surface mounting 4 sets for wall flush mounting 3 User s manual 4 Packing box XX 1 5 X s i DESIGNATION Mounting option KEY N wall surface mounting V wall flush mounting Maximum current A 1 5 Appliance type Designation key example TH 1 5 H timer with humidity sensor maximum current load 1 5 for wall surface mounting T timer TH timer with humidity sensor TF timer with photo sensor TP timer with motion sensor DMA U B R MAIN Input voltage 50 Hz V 220 240 TECHNICAL DATA Max output power VA 330 Max load curren
14. t A 1 5 Overall dimensions mm 162x80x70 Weight g 400 The control unit front panel is shown in Fig 10 DESCRIPTION AND DESIGN 1 control unit operation lamp 2 photo sensor for TF only 3 time off delay control knob 2 up to 30 minutes 4 humidity set point control knob for TH only or illumination set point control knob for TF only 5 motion sensor for TR only U B IR DA The timer is available in four modifications Timer T The control unit supplies voltage to the connected fan after the external switch e g the light switch supplies control signal to the input terminal LT After the control voltage is off the control unit continues to supply power to the fan within the time period set by the timer 2 30 min Timer with humidity sensor TH The control unit supplies voltage to the connected fan after the external switch e g the light switch supplies control signal to the input terminal LT or if the indoor humidity exceeds the set point 60 90 After the control voltage is off or after the humidity falls below the set point the control unit continues to supply power to the fan within the time period set by the timer 2 30 min Timer with photo sensor TF The control unit supplies voltage to the connected fan after the external switch e g the light switch supplies control signal to the input terminal LT or if the lighting intensity exceeds the set point After t
15. us smooth fan speed control The delivery set includes 1 Controller Titem 2 Self tapping screws with dowels 2 sets for wall surface mounting 4 sets for wall flush mounting 3 Spare fuse 1 5A for RS 1 2 0 A for RS 1 5 2 5 A for RS 2 3 15 A for RS 2 5 1 item 4 Plastic screwdriver 1 item 5 User s manual 6 Packing box RS X X Mounting option N wall surface mounting V wall flush mounting Maximum current A 1 1 5 2 2 5 Designation kev example RS 1 N speed controller with maximum current 1 A for wall surface mounting Appliance tvpe RS 1 RS 1 5 RS 2 RS 2 5 Input voltage 50 Hz V 220 240 Max output power VA 230 345 460 575 Max load current A 1 1 5 2 2 5 Overall dimensions mm 162x80x70 Weight g 300 U 13 IR GWI EJTTS The controller front panel is shown on fig 4 The control knob position corresponds to the fan rotation speed peel The control internal design is shown on fig 5 1 Output wire clamp 2 Input wire port 3 Fuse 4 Controller circuit board 5 Minimum speed setup potentiometer PO YT CONNECTION TO POWER MAINS MINIMUM SPEED SETTING UBER To connect the speed controller to the power mains follow the wiring connection diagram Fig 6 Connection sequence Remove the decorative front panel and the base Fig A and B
16. ustomer in case of incompliance of the model or marking of the product with data specified on the product packaging and in the User Manual or other relevant substituting document in case of non timely technical maintenance of the product by the customer dust mud oil condensate foreign particles in case of causing external damage to the product by the customer damage shall not apply to external changes of the product required for the product mounting in case of altering the product design or further reworking of the product in case of replacing and using parts units and components of the product not prescribed by the manufacturing company in case of other use of the product other than intended use in case of the customer s violating product operation rules in case of connecting the product to electric mains of voltage exceeding voltage value specified in the user s manual in case of step voltage that resulted in the product failure in case of the customer s performing unauthorised repair of the product in case of performing repair of the product by third persons unauthorized by the manufacturing company QYVZNTS UBR in case of warranty period service life expiry in case of the customer s violating transportation rules assuring prevention of damaging and or destruction of the product in case of the customer s violating product storage rules in case of performing unlawful actions by third persons with respect
17. very set includes 1 Controller 1 item 2 Self tapping screws with dowels 2 sets for wall surface mounting 4 sets for wall flush mounting 3 User s manual 4 Packing box PX 5 0 X _ Mounting option N wall surface mounting V wall flush mounting Maximum current A 5 0 Number of selectable switch positions 233 5 Designation key example P3 5 0 N 3 position speed switch maximum load current 5 A intended for wall surface installation Input voltage 50 Hz V 220 240 Max output power VA 1000 Max load current A 5 0 Overall dimensions mm 162x80x70 Weight g 250 U 13 IR DIM The switch front panel is shown on Fig 7 The switch knob position corresponds to the fan rotation speed The switch internal design is shown on Fig 8 DESCRIPTION AND DESIGN 1 Output terminal block 2 Input terminal block venrs UBR To connect the speed switch to the power mains follow the wiring connection diagram Fig 9 The switch may be connected to several fans provided that the total power CONNECT ONO ae POWER MAINS consumption is below 1000 VA Connection sequence Remove the decorative front panel and the base Fig A and B Route the wires through the ports in the speed switch casing Strip the wire ends 7 8 mm long Connect the wire
Download Pdf Manuals
Related Search