KT&C KPC-N635NH10 User Manual
Contents
1. 30 mA IR on AC 24 V nominal 3 W 6 6 W IR on 4 F 122 F 20 C 50 C IP66 weather resistant Metal housing with sun shield bottom weather sealed access ports for len controls IR level and video test point Body across sunshield 4 02 diameter 12 34 long w sunshield 12 34 ir longest extension in 90 position 10 4 long and 5 77 high 2 45 pounds CEJ FCC 1 4 Dimensions Camera Body 313 32mm 12 34in 16Smm 6 61in _ 5 fmmi2 38in 102 06mm 4 02in mmm 2664mm 10 48in 102 1mm 4 02in 146 5mm 5 76in 89 1mm 3 50in ARORA k FY ret 151 5mm 5 96in 75 6mm 2 98in 83 5mm 3 28in 86 83mm 3 419in 101 5mm 3 602in 4 Smm 0 197in 1 5 Camera Component Description Speedy mount Ring Speedy mount Ring Grasp and twist to remove the over Test point and IR level onfrols are inside the cover 1 IR Level Control adjust IR level to control excessive illumination 2 Video Test for dim and focus access to video at the camera use the Video Test Cable supplied t a hand held test monitor EN220 or similar Chapter 2 2 INSTALLATION This chapter will describe in general terms how to install the KPC N635NH10 camera STEPS 1 Wire and mount the camera See 2 1 2 Adjust the camera position See 2 2 Warning To prevent electrical shock turn off the electrical power before making electrical connections 2 Wiring and Mounti2. Cox C INNOVATIVE HIGH DEFINITION SURVEILLANCE KPC N635NH10 IR Dual Voltage Varifocal IP66 Bullet Camera User Guide Installation Operation Instructions FE CE www ktncusa com Operation Instructions Please read this manual first for correct installation and operation This manual should be retained for future reference The information in this manual was current when published The manufacturer reserves the right to revise and improve its products All soecifications are therefore subject to change without notice Precautions 1 Do not install the camera near electric or magnetic fields Install the camera away from TV radio transmitters magnets electric motors transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image 2 Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage 3 Try and avoid facing the camera toward the sun In some circumstances direct sunlight or may cause permanent damage to the sensor and or internal circuits 4 Keep the power cord away from water and other liquids and never touch the power cord with wet hands Touching a wet power cord with hands or touching the power cord with wet hands may result in electric shock 5 Never install the camera i
3. amera that you have been waiting for to create analog CCTV systems that produce outstand 1 Features High performance sensor delivers native 01 lux low light sensitivity before IR illumination Resolution of over 600 horizontal TV lines for improved image quality Flexible positioning for convenient wall or ceiling mounting Varifocal 2 8 12mm lens with convenient external adjusters to capture the desired field of view Equipped with 42 IR LEDs for 120 foot 40m range depending on scene IR reflectivity Adjustable IR output level to achieve detection range while avoiding interference from reflectic Reflection preventing dual section cover glass isolates IR emitters from lens to prevent image dis Video test output point for convenient aim and focus during installation and ease of service Cables protected from weather and tampering by the mounting base Convenient rapid mount base plate easily attaches to surface camera attaches to plate with n screws Operating range down to 4 degrees Fahrenheit IP66 weather resistant Dual voltage 12VDC 24VAC operation 1 2 Accessory Parts List Please be careful when you unpack the box and the electronic device inside Check and make sur that you have all the items listed below inside the original box e Camera Unit x I e Rapid Mount Ring x e Operation Manual x 1 e Video Test Cable x e Power pigtail x Mounting kit includes e Long Screws x 4 for attaching EZ Mount Ring to mounting sur
4. face e Short Screws x 4 for connecting camera base to EZ Mount Ring e Expanding Anchors x 4 e Hex key x for adjusting camera e Hexagon wrench x I for adjusting sunshield and set screw in base e Mounting Template x Note If an item appears to have been damaged in shipment replace it properly in its carton and notify the shipper If any items are missing notify your KT amp C Electronics Corp Sales Representative or Customer Service The shipping carton is the safest container in which the unit may be transported save it for possible future use 1 3 Specifications Imaging Device Video Format Effective Picture Elements Horizontal Resolution Sensitivity IR LEDs IR Range IR Switch Points S N Ratio Video Qutput Gamma Correction Lens Type Positioning Day Night Electronic Shutter sync Mode Power Source Power Consumption Operating Temperature Environmental Mechanical Dimensions Weight Certifications 1 3 High Sensitivity CCD NTSC 768 H x 494 V More than 600TVL 0 lux with IR on O1 lux native from sensor 42 LEDs with output at 850nm and adjustable level to 120 feet depending on scene IR reflectivity On at 1 lux Off at 3 lux Over 48cB AGC off BNC 1 0V p p 750 video test point inside cover cable supplied 0 45 Varifocal 2 8 12mm electronic iris Flexible positioning for wall or ceiling mounting Electronic D N 1 60 1 100 000 sec Internal DC 12V AC 24 V DC 12 V nominal 80 mA 4
5. ment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 this device must accept any interference received including interference that may cause undesired operation ATTENTION This is a class A product which may cause radio interference in a domestic environment in this case the user may be urged to take adequate measures QOS wis This Product is ROHS compliant Your KT amp C product is designed and manufactured with high quality materials and components which can be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from your household waste Please dispose of this equipment at your local community waste collection recycling centre In the European Union there are separate collection systems fo
6. n areas exposed fo oil gas or solvents Oil gas or solvents may result in equipment failure electric shock or in extreme cases fire 6 Cleaning Do not touch the surface of the sensor directly with the hands Use a damp soft cloth to remove any dirt from the camera body Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens Please do not use complex solvents corrosive or abrasive agents for cleaning 7 Do not operate the camera beyond the specified temperature humidity or power source ratings Use the camera at temperatures within 20 C 50 C 4 F 122 F and in an IP66 complaint environment this device is not rated as submersible The input power source is 12 V DC 24 V AC Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equioment does cause harmful interference to radio or television reception which can be determined by turning the equip
7. ng Use the template and an appropriate tool to drill 4 holes to attach the rapid mount ring If no surface please insert the provided plug into the ring from the underside the plug will be held securely in place If surface wire access is required simply omit the plug to leave the surface wire channel clear Push the plastic anchors into the 4 holes 3 Take a long Phillips pan head screw and tighten it through the EZ Mount Ring counter bored hole in Repeat this step until all 4 screws are secured to the wall ceiling EE 4 Drill a 1 diameter hole within the interior of the EZ Mount Ring 5 Pull the cables fo be connected to power amp video cables from the ceiling or wall Video amp Power Cables Gnd or 24 VAC 12VDC or 24 VAC Power Socket Connect the power and video cables Attach the camera to the rapid mount ring securing it with the 4 socket head cap screws provided Power and Video connection 2 Adjust Camera Position Adjust the viewing angle to the desired direction With this unique 3 axis positioning system installers ci from virtually any angle without compromising The camera can be adjusted in 3 ways lst Axis Use a hexagon key to loosen this screw to rotate the camera 360 2nd axis ESE _ a Use a hexagon key to loosen this screw to rotate the camera 180 12 12 Loosen lock ring and set screw to
8. r used electrical and electronic product The information in this manual was current upon publication The manufacturer reserves the right to revise and improve his products Therefore all soecifications are subject to change without prior notice Misprints reserved Please read this manual carefully before installing and using this unit Be sure to keep it handy for later reference Table of Contents Chapter Chapter 2 Product Overview 1 1 Features 1 2 Accessory Parts List 1 3 Specifications 1 4 Dimensions 1 5 Camera Component Description Installation 2 1 Wiring and Mounting 2 2 Adjust Camera Position OO CON O 01 10 12 Chapter I 1 PRODUCT OVERVIEW The KT amp C KPC N635NH10 uses 42 IR LEDs with adjustable level control to produce 600TVL day night images in low or no light out to a range of 120 feet or more The KPC N635NH10 offers flexible positioning for wall or ceiling mounting in an IP66 weather resistant vandal resistant bullet housing with operation down to 4 F varifocal 2 8 12mm lens with weather resistant screw type external lens controls for easily adjustable field of view reflection preventing dual section cover glass adjustable IR level fo achieve detection range while avoiding interference from reflec tions dual voltage 12V DC 24V AC operation rapid mount base plate base plate is easily mounted to the wall camera attaches to base plate with machine screws This is the economi cal IR c
9. rotate camera 360 Sunshield To remove or install the sunshield use flat blade screw driver to loosen the screw at sunshield Secure with this 4 Note When properly installed the rear of the sunshield is even with the rear of the camel the sunshield to shade the lens can compromise image quality 13
Download Pdf Manuals
Related Search