User`s Manual - Global Systems Communications SRL
Contents
1. CountrwRegion United States Y Secondary RJ45 Power O Enabled Disabled Spanning Tree Enabled Disabled STP Forward Delay p 1 30 seconds Figure 16 Basic System Settings Basic Settings Device Name Specify the device name which is composed of no more than 15 characters with 0 9 A Z a z or Network Mode Specify the network mode including Bridge and Router lt is easy to configure parameters in Bridge Mode however users must pay extra attention to the way they configure the device when it is set to Router Mode For details please refer to IP Settings Router Ethernet 1 Data Rate Specify the transmission rate of data of LAN1 Default is Auto Ethernet 2 Data Rate Specify the transmission rate of data of LAN2 Default is Auto Country Region The availability of some specific channels and or operational frequency bands are country dependent Secondary RJ45 Power The secondary Ethernet port labeled LAN 2 is for IP video integration To use it you need to enable the secondary port via WEB UI in advance before connecting with the IP camera Spanning Tree Spanning Tree Protocol STP is a link management protocol for AP which provides path redundancy while preventing loops in a network STP allows only one active path at a time between the access points but establish the redundant link as a backup if the initial link fails STP Forward Delay STP Forward Delay is the time spent in detecting2. DMZ Setting 802 11a n Outdoor Wireless Access Point System Wireless Management Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway s NAT firewall O Enable Port Forwarding IP Address A Protocol Bath Port Range Comment Delete Selected Delete All Figure 25 Port Forwarding DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network Typically the DMZ host contains devices accessible to the Internet traffic such as Web HTTP servers FTP servers SMTP e mail servers and DNS servers SY PLANET Networking amp Communication 802 11a n Outdoor Wireless Access Point status System Wireless Management Basic Settings DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network Typically the DMZ host contains devices accessible to Internet traffic such as Web HTTP servers FTP servers SMTP e mail servers and DNS servers TCP IP Settings Time Settings O Enable DMZ RADIUS Settings DMZ Host IP Address Firewall Settings Src IP Filtering Dst IP Filtering Src Port Filter
3. c0ssscccccccessteseseeeeececccctoesecetceccccesseeecseeesecccesseseesesstecossateesenees 27 Figure 29 Ste UI cea 30 Figure 29 Adv anced Wireless SENINGS ct A A ee 31 Figure 30 SECU SINO Stalin odo eeb ene 34 Foure SI ACGESS CONTO iia ii ii ile 36 Figure 32 WDS SEttidQS cccccccocccnncccnnnccnonononncnnnnnnnnnnnnnnnnnnnnnnnnnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnneninnnnns 37 Figure 33 SNMP GoniduraUON etter ls dosel 38 Figure 34 Configure SNMPv3 User Profile ccccccccooccconcconnnccocononcnnnnconooononnnnonnnonononannnnnnnnnnos 39 Fig re 35 Upgrade iW ANS sans cdi 41 Figure 36 Backup Relrieve SS NOS meteen acid eel vie 42 Figure 37 Restore STINGS tien tetten dd la do e 43 Foures REDOO tai ds td a ia 44 Figure 39 PASS WO A A A AAA 45 Figure 40 System LOG osrin ernea inana aeaa er Ea Aie A UiS aa A E AAA a aa A E Aia aE 46 Figure 41 Ste SUIVEY TOO senden ienie laicos 47 Figure 42 Ping Wanda de 47 Eure ASB ASIC INFOMMNAROM ia 49 Figure 44 GON CHOMN eii li ida lira iods 50 Figure 45 Network Flow STalStOS 0 00 iia 51 Elo AP A o ne e A 52 ial 2 U1 ras A e A 53 Figure 48 DHCP Client Table oooocccccccconncnncconocncnncncnoncnnnonononcnnoononnnnnononnnnnnnononnnrnnnnnnnnnrnnnnonnnnrncnnnnanens 53 Table t Factory Delasu Se GS ia a 13 Table 2 Al a isc 57 Table 3 Public Software Name and DescriptiON oococccococccccocccocncococococonnconnconnnonnnnnnnnnnnnnnns 59 Chapter
4. Figure 39 Password Note The password is case sensitive and its length cannot exceed 19 characters 5 7 System Log System log is used for recording events occurred on the WNAP 7300 including station connection disconnection system reboot and etc Open System Log in Tools as below Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication status System Wireless Management System Log gt gt System Log Site Surve y Use this page to set remote log server and show the system log Ping Watchdog Remote Syslog Server C Enable Remote Syslog Port 514 WER meten O Time Source M 14 00 00 05 00 30 4F 4E 28 40 WLANsemicestopped 2 00 00 05 00 30 4F 4E 28 A0 WLAN serice started 3 00 00 05 00 30 4F 4E 28 A0 WLAN service stopped Pa 00 00 05 00 30 4F 4E 28 40 WLAN service started 5 00 00 05 00 30 4F 4E 28 A0 WLAN service stopped 6 00 00 05 _ 00 30 4F 4E 28 A0 WLAN service started Terre Figure 40 System Log a Remote Syslog Server Enable Remote Syslog Enable System log to alert remote server IP Address Specify the IP address of the remote server Port Specify the port number of the remote server 5 8 Site Survey Only available under Wireless Client mode site survey allows you to scan all the APs within coverage Open Site Survey in Tools as below and select the desired AP to connect
5. PLANET Networking Communication 802 11a n Outdoor Wireless CPE AP Router WNAP 7300 User s Manual Version 1 0 Copyright Copyright 2011 by PLANET Technology Corp All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of PLANET PLANET makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Any software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not this company its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software Further this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes All brand and product names mentioned in this manual are trademarks and or registered trademarks of their respective holders FCC Caution To assure continued compliance Example use only shielded interf
6. Program Copy Right Origin Sour Licenses or License Terms Name Description Code Distribution Models or Website its special license Reference terms Wolfgang Denk ftp ftp denx de GNU GENERAL GNU GENERAL DENX Software pub u boot PUBLIC LICENSE PUBLIC Engineering Version 2 LICENSE Version wd denx de 2 Busybox http www busy GNU GENERAL http www gnu or box net downloa PUBLIC LICENSE g licenses old lice ds busybox 1 01 Version 2 nses gpl 2 0 html tar bz2 Goahead Copyright c http data goahe GoAhead Software ad com Software Inc 1992 2000 Webserver 2 1 8 webs218 tar gz hostapd wpa_sup plicant vsftpd Copyright c 2002 2006 Jouni Malinen lt jkmaline cc hut fi gt and contributors Copyright c 2003 2005 Jouni Malinen lt jkmaline cc hut fi gt and contributors Copyright 1997 1999 2000 2003 Larry Doolittle Copyright c 2001 2003 Networks Associates Technology Inc All rights reserved Author Chris Evans http hostap epit est fi releases h ostapd 0 4 8 tar QZ http hostap epit est fi releases w pa_supplicant 0 4 7 tar gz http doolittle ica rus com ntpclien t ntpclient_2003 _194 tar gz http prdownloa ds sourceforge n et net snmp net snmp 5 4 1 tar gz ftp vsftpd beast s org users ceva ns vsftpd 1 1 2 t ar gz ftp ftp kernel or g pub linux kern el v2 6 linux 2 6 15 tar bz2 GNU GENERAL PUBLIC LICENS
7. 3 PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management System Log Wireless Site Survey This page provides tool to scan the wireless network If any Access Point or IBSS is found you could choose to connect it manually when client mode is enabled Site Survey gt Ping Watchdog O Wireless derek 149 00 30 4F 4E 28 A0 a n 72 NONE Figure 41 Site Survey Tool 5 9 Ping Watch Dog If you mess your connection up and cut off your ability the log in to the unit the ping watchdog has a chance to reboot due to loss of connectivity Y PLANET 802 11a n Outdoor Wireless Access Point Networking 4 Communication Status System Wireless Management System Log Ping Watchdog This page provides a tool to configure the Ping Watchdog If the failcount of the Ping reaches to a specified value the watchdog will reboot the device Site Survey Ping Watchdog C Enable Ping Watchdog Ping Interval zoo seconds Startup Delay 120 seconds 120 Failure Count To Reboot Figure 42 Ping Watchdog Ping Watchdog Enable Ping Watchdog Io activate ping watchdog check this checkbox IP Address to Ping Specify the IP address of the remote unit to ping Ping Interval Specify the interval time to ping the remote unit Startup Delay Specify the startup delay time to prevent reboot before the WNAP 7300 is fully initialized Failure Count To Reb
8. 64 bits WEP It is made up of 10 hexadecimal numbers 128 bits WEP It is made up of 26 hexadecimal numbers 152 bits WEP It is made up of 32 hexadecimal numbers TKIP Temporal Key Integrity Protocol which is a kind of dynamic encryption is co used with WPA PSK etc AES Advanced Encryption Standard it is usually co used with WPA2 PSK WPA WPA2 etc TKIP AES It allows for backwards compatibility with devices using TKIP Note We strongly recommend you enable wireless security on your network e Only setting the same Authentication Data Encryption and Key in the WNAP 7300 and other associated wireless devices can the communication be established 4 2 2 Access Control The Access Control appoints the authority to wireless client on accessing the WNAP 7300 thus a further security mechanism is provided This function is available only under AP mode Open Access Control in Wireless as below Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management Basic Settings Wireless Access Control Security Settings ee 2 If you choose Allowed Listed only those clients whose wireless MAC addresses are in the access control list will be able to connect to your Access Point When Deny Listed is selected these Advanced Settings wireless clients on the list will not be able to connect the Access Point Access Control gt Access Co
9. AEN Ns EN 36 AAA nn e 37 Chapter 5 Mandagementummmenriendtini eden ei ever inven nde veder nde bedienend 38 Sal MIR Management tise ett ea eee eee ensen 38 5 1 1 Configure SNMPv3 User Profile sassoni i a 39 9 2 Upgrade FlIMWa sacate ica en odie lr lilas 40 9 9 Backup Reeve SENGS pna A A 42 5 4 Restore Factory Default Settings ccooocooncccnnncccconononcnnnnncnononancnnnnnnnononannnnnnnnnnonnnnnnnnnnncnnnnnnnns 43 EN ad 66 En 43 DO FP ASSW fe go secina op e E a I aE AER awed uapaduiceiad iavad 44 ES A ee ee TD 45 908 ee Nae a ternet etek eend a eee eee ere ee 46 IPNI VV ACM DOG ree e asin atitesnaviaadtnouts 47 Chapter 6 Slats aria A dimen se nie indice 49 BA VIGW BASIC MO MAMA diia 49 5 2 WICW ASSOCIATION Saca AA de oee enen 50 6 3 View Network FlOW Stats tes cie niine a ita 50 64 VIEW ARP Table ci 52 6 5 VIEW Bdge Table cantidad 52 6 6 View Active DHGP Client Table aii 53 Chapter 7 ThOUDIESHOOUING msi la ias 54 Append Aas CW ices cani RIAs 56 Appendix B GPL Declamation cuina 57 FIGURE Figure 1 WNAP 7300 ccccccssseeecssseeecsesececceuseeccsaeceesaueeecseuseeceeaseeessageessauseeeseasecessageesssageeseseuseesseags 1 FIQUES 2 INDICAN APPICA NO Mira matado ian htt behalen ditadii uted metten 2 Figure 3 Move ine COVE ee ende 6 Figure 4 Cable COnMSCIOM al a 6 Figure 5 Enable the Secondary RJ45 POWerF occcccccccccoconnnccnncccccccoonnccnnnncncnnnonnccnnnnnnnonnnannnnnnnnnnnnenanncnnnnnns 7 Fi
10. Wireless Management Basic Settings Wireless Advanced Settings Security Settings These settings are only for more technically advanced users who have a sufficient knowledge 5 about wireless LAN These settings should not be changed unless you know what effect the Advanced Settings changes will take Access Control Wii Support Enabled Disabled WDS Settings A MPDU aggregation Enabled Disabled a A MSDU aggregation Enabled Disabled Short Gl Enabled Disabled RTS Threshold 12346 1 2346 Fragment Threshold 2346 256 2346 Beacon Interval 100 20 1024 ms DTIM Interval 1 a255 Preamble Type O Long Short IGMP Snooping Enabled Disabled Wireless Separation O Enabled Disabled RIFS Enabled Disabled Link Integration O Enabled Disabled Sta Num Limitation Enabled Disabled Max Station Num 32 0 32 Space In Meter y AA A o 0 15000m Flow Control Enable Traffic Shaping Incoming Traffic Limit Outgoing Traffic Limit Figure 29 Advanced Wireless Settings e WMM Support WMM Wi Fi Multimedia is a subset of 802 11e It allows wireless communication to define a priority limit on the basis of data type under AP mode only thus those time sensitive data like video audio data may own a higher priority than common one To enable WMM the wireless client should also support it A MPDU A MSDU Aggregation The data rate of your WNAP 7300 except wireless cl
11. 1 Introduction 1 1 Introduction Designed for outdoor environment application the WNAP 7300 is a high performance 802 11a n 2x2 MIMO broadband solution that provides fast and reliable wireless network coverage Designed with IEEE 802 11n standard high output power and built in 16dBi dual polarity antenna makes it possible to deliver several times faster data rate than normal wireless device and higher bandwidth with longer range for outdoor applications The WNAP 7300 supports four wireless communication connectivity AP Wireless Client WDS and AP WDS allowing for various application requirements thus helping to find the key to the last mile with least effort With high output power and reliable performance the WNAP 7300 is an ideal wireless broadband solution for wireless Internet service providers and system integrators 1 2 Appearance 802 114 n Outdoor Access Pont Figure 1 WNAP 7300 1 3 Key Features e Compliant with IEEE 802 11a and IEEE 802 11n as well Support Power through Ethernet which is supplied with 15V e High reliable watertight housing endures almost any harsh environments Four operating modes including AP Wireless Client WDS and AP WDS a Support 64 128 152 bit WEP and 802 1X WPA WPA2 WPA amp WPA2 WPA PSK WPA2 PSK and WPA PSK amp WPA2 PSK etc a User friendly Web and SNMP based management interface 1 4 Typical Application This section describes the typical applications of the WNAP 7300
12. By default it is set to AP mode which allows it to establish a wireless coverage besides it is also able to join any available wireless network under wireless client mode The WNAP 7300 is able to deliver stable and efficient broadband connectivity for various applications A LN 1 ge og L AP 3 Wi Fi Coverage Wireless Client Figure 2 Typical Application Chapter 2 Hardware Installation This chapter describes safety precautions and product information you have to know and check before installing the WNAP 7300 2 1 Preparation before Installation 2 1 1 Professional Installation Required Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable in the local regulations 2 1 2 Safety Precautions 1 To keep you safe and install the hardware properly please read and follow these safety precautions 2 If you are installing the WNAP 7300 for the first time for your safety as well as others please seek assistance from a professional installer who has received safety training on the hazards involved 3 Keep safety as well as performance in mind when selecting your installation site especially where there are electric power and phone lines 4 When installing the WNAP 7300 please note the following things Do not use a metal ladder Do not work on a wet or windy day Wear shoes with rubber soles and heels rubber gloves lo
13. Client The WNAP 7300 is able to connect to the AP and thus join the wireless network around it Bridge The WNAP 7300 establishes wireless connectivity with other APs by keying in remote MAC address Please refer to the WDS Setting for detailed configuration AP Bridge The WNAP 7300 servers as AP and Bridge concurrently In other words it can provide connectivity services for WNAP 7300s under WDS mode Wireless Network Name SSID a This wireless network name is shared among all associated devices in your wireless network Keep it identical on all those devices Note that the SSID is case sensitive and cannot exceed 32 characters Broadcast SSID In AP mode hiding network name is necessary when you are in a wireless environment that may have potential risk By disabling broadcast SSID the STA cannot scan and find the WNAP 7300 so that malicious attack by some illegal STA could be avoided 802 11 Mode The WNAP 7300 can communicate with wireless devices of 802 11n or 802 11a n You can also select Auto and make it work under an appropriate wireless mode automatically HT Protect Enable HT High Throughput protect to ensure HT transmission with MAC mechanism Under 802 11n mode wireless client can be divided into HT STA and Non HT STA among which the one with HT protect enabled gets higher throughput Channel Number Channel varies much as the available band differs from country to country Select a proper operating channel i
14. S O ice N ice K IN O K al U N Jl O ce O1 iN O dal N ice O iN N m oO N iN TI O N ev 00 O1 a pa 2 EST E EI E EST ES EST E a po es je EST E 2a paa 2 pp 45 2 pp 2 Je EI CS a po se po FET ES ECO 5 CS FEST N a joo B P Appendix B GPL Declamation PUBLIC SOFTWARE DECLAMATION In the software we delivered there may contains some public software if it is please read below carefully 1 Definition Public Software when applicable shall mean that portion of the Licensed Software in source code form set forth in the below Table and provided under the terms set forth in the Section 5 the indicated website the complete license terms can be found Public Software shall mean each of a any computer code that contains or is derived in any manner in whole or in part from any computer code that is distributed as open source software e g Linux or similar licensing or distribution models and b any software that requires as a condition of use modification and or distribution of such software that such software or other software incorporated into derived from or distributed with such software i be disclosed or distributed in source code form ii be licensed for the purpose of making derivative works or iii be redistributable at no charge Public Software includes without limitation software licensed or distributed under any of t
15. and learning network tree topology state before entering the forward state Default time value is 1 sec TCP IP Settings Open TCP IP Settings in System as below to configure the parameters for LAN which connects to the LAN port of the WNAP 7300 In this page users may change the settings for IP Address Subnet Mask and DHCP Server gt PLANET 802 11a n Outdoor Wireless Access Point Status System Wireless Management Basic Settings TCP IP Settings TCP IP Settings y Use this page to configure the parameters for local area network which connects to the LAN port of your Access Point Here you may change the setting for IP address subnet mask DHCP etc Time Settings nnn nanne RADIUS Settings IP Address Assignment Firewall Settings Obtain IP Address Automatically EL Use Fixed IP Address IP Address 192 168 1 1 Subnet Mask 255 255 255 0 Gateway Ip Address 0 0 0 0 DNS 1 0 0 0 0 DNS 2 0 0 0 0 Figure 17 TCP IP Settings Bridge Obtain IP Address Automatically If a DHCP server exists in your network you can check this option thus the WNAP 7300 is able to obtain IP settings automatically from that DHCP server Note When the IP address of the WNAP 7300 is changed the clients on the network often need to wait for a while or even reboot before they can access the new IP address For an immediate access to the bridge please flush the netbi
16. in advance Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management Basic Settings Time Settings TCP IP Settings You can synchronize System Log s time stamp with a public time server over the Internet Time Settings Current Time En RADIUS Settings Time Zone Select O Enable NTP client update Firewall Settings NTP server Manual IP 0 0 0 0 Apply Cancel Figure 19 Time Settings a Current Time Display the present time in Yr Mon Day Hr Min and Sec Time Zone Select Select the time zone from the dropdown list NTP Server Select the time server from the NTP Server dropdown list or manually input the IP address of available time server into Manual IP Hit Apply to save settings 3 6 RADIUS Settings RADIUS Remote Authentication Dial In User Service is a server for remote user authentication and accounting playing a central role in the network in providing the capabilities of authenticating authorizing accounting auditing alarming and etc It allows an organization to maintain user profiles in a central database that all remote servers can share Open RADIUS Settings in System to make RADIUS configuration Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication status System Wireless Management Basic Settings RADIUS Settings Use
17. will pop up Save it then the configuration file like ap cfg will be saved to your local computer Load Setting from File By clicking Browse a file selection menu will appear select the file you want to load like ap cfg Click Upload to load the file After automatically rebooting new settings are applied 5 4 Restore Factory Default Settings The WNAP 7300 provides two ways to restore the factory default settings a Restore factory default settings via Web From Configuration File clicking Reset Settings to Default will eliminate all current settings and reboot your device then default settings are applied Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management SNMP Configuration Configuration File This page allows you to save current settings to a file or load the settings frorn the file which was 8 saved previously Besides you could reset the current configuration to factory default or reboot Configuration File gt gt the device Firmware Upload Password Settings Y Save Settings to File Load Settings from File CBrowse Upload Reset Settings to Default Reboot The Device Figure 37 Restore Settings Restore factory default settings via Reset Button If software in the WNAP 7300 is unexpectedly crashed and no longer reset the unit via Web you may do hardware reset via the reset button Press and
18. 00 When finished you can check the connection as the figure shown below Figure 7 Attach and fasten the removable cover O Plug the power cord into the DC port of the POE injector as the figure shown below 39u Jau33 Figure 8 Connect to POE Injector 6 Plug the other side of the Ethernet cable in the Step 4 into the POE port of the POE injector in the Step 5 and get the complete set ready as the figure shown below le BDZ 114 Cull Actora Pint Figure 9 Complete Set i Note Be reminded the UTP wire distance toward your WNAP 7300 to the Ethernet devices such as Ethernet Switch is 100 meters the passive POE injector can be in any point of this 100 meters UTP distance where there is a shell or protected location Power on the WNAP 7300 by plugging the power adapter to the power socket 2 2 2 Using the External Antenna The WNAP 7300 provides two reverse SMA antenna connectors if you prefer to use the external antenna for your application instead of the built in directional antenna please follow the steps below 1 Remove the two plugs as circled below Figure 10 Remove the plugs 2 Connect your external antenna to the SMA type connectors at the bottom of the WNAP 7300 Figure 11 Connect to external antenna 10 dk Warning Users MUST power off the WNAP 7300 first before connecting the external antenna to it Do not switch from built in antenna to the external antenna from W
19. 2 GNU GENERAL PUBLIC LICENSE Version 2 GNU GENERAL PUBLIC LICENSE Version 2 http www gnu or g licenses old lice nses gpl 2 0 html http www gnu or g licenses old lice nses gpl 2 0 html http www gnu or g licenses old lice nses gpl 2 0 html http www gnu or g licenses old lice nses gpl 2 0 html http www gnu or g licenses old lice nses gpl 2 0 html kuznetOms2 inr ac ru Pppd Paul Mackerras ftp ftp samba or lt paulus linuxcare g pub ppp com gt
20. 7300 Use of such filters can be helpful in securing or restricting your local network PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management Basic Settings B Source IP Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your Time Settings local network TCP IP Settings RADIUS Settings C Enable Source IP Filtering Firewall Settings Local IP Address Comment Src IP Filtering Dst IP Filtering Src Port Filtering Dst Port Filtering Local IP Address Comment Select Port Forwarding DMZ Setting Figure 21 Source IP Filtering Destination IP Filtering The destination IP filtering gives you the ability to restrict the computers in LAN from accessing certain websites in WAN according to specified IP addresses Check the Enable Destination IP Filtering checkbox and enter the IP address of the clients to be restricted Hit Apply to make the setting take effect SY PLANET Networking amp Communication Basic Settings TCP IP Settings Time Settings RADIUS Settings Firewall Settings Src IP Filtering Dst IP Filtering Sre Port Filtering Dst Port Filtering Port Forwarding DMZ Setting Source Port Filtering The so
21. E Version 2 GNU GENERAL PUBLIC LICENSE Version 2 GNU GENERAL PUBLIC LICENSE Version 2 GNU GENERAL PUBLIC LICENSE Version 2 GNU GENERAL PUBLIC LICENSE Version 2 GNU GENERAL PUBLIC LICENSE Version 2 http www gnu or g licenses old lice nses gpl 2 0 html http www gnu or g licenses old lice nses gpl 2 0 html http www gnu or g licenses old lice nses gpl 2 0 html http www gnu or g licenses old lice nses gpl 2 0 html http www gnu or g licenses old lice nses gpl 2 0 html http www gnu or g licenses old lice nses gpl 2 0 html iptables Igmpproxy Copyright 2000 2004 netfilter project http www netfilter o rg Copyright c 1998 2008 The OpenSSL Project All rights reserved Copyright C 2005 Johnny Egeland lt johnny rlo org gt Copyright C 1998 Brad M Garcia lt garsh home com gt Stephen Hemminger shemminger osdl org Alexey Kuznetsov ftp ftp netfilter o rg pub iptables i ptables 1 3 6 tar bz2 http www open ssl org source o penssl 0 9 8k tar gz http sourceforg e net projects ig mpproxy files ig mpproxy 0 1 igm pproxy 0 1 tar gz download http sourceforg e net projects dn rd files dnrd 2 12 dnrd 2 12 tar gz download http developer osdl org dev ipro ute2 GNU GENERAL PUBLIC LICENSE Version 2 GNU GENERAL PUBLIC LICENSE Version 2 GNU GENERAL PUBLIC LICENSE Version
22. EB management without physically attaching the external antenna onto the WNAP 7300 otherwise damage might be caused to the unit itself Follow the steps described in Connect Up to finish the installation 2 2 3 Pole Mounting la Turn the WNAP 7300 over Put the pole mounting rings through the middle hole of it Note that you should unlock the pole mounting ring with a screw driver before putting it through the WNAP 7300 as the following right picture shows Figure 12 Pole Mounting Step 1 2 Mount the WNAP 7300 steadily to the pole by locking the pole mounting ring tightly The mounting ring supports pole diameter 32mm to 70mm Figure 13 Pole Mounting Step 2 3 Now you have completed the hardware installation of the WNAP 7300 Basic Settings Chapter 3 Basic Settings 3 1 Factory Default Settings We ll elaborate the WNAP 7300 factory default settings You can re acquire these parameters by default If necessary please refer to the Restore Factory Default Settings Table 1 Factory Default Settings Features Factory Default Settings admin admin apXXXXXX X represents the last 6 digits of Ethernet MAC address gt D Auto 192 168 1 1 255 255 255 0 0 0 0 0 0 0 0 0 0 0 0 0 Enable 802 11a n United States 149 Wireless Enable Disable Auto 100 Full 20MHz Enabled 2346 2346 100 Disable Open System None SNMP IP Address 0 0 0 0 3 2 System Requirements Before
23. able and then enable the WDS This function can work only in Bridge and AP Repeater mode Security Settings Access Control WDS Settings Local MAC Address 00 30 4f4e 28 a0 Remote AP MAC Address1 00 30 4f 4e 28 a1 Remote AP MAC Address2 Remote AP MAC Address3 Remote AP MAC Address4 Figure 32 WDS Settings Enter the MAC address of another WNAP 7300 you wirelessly want to connect to into the appropriate field and click Apply to save settings h Note e WDS Settings is available only under Bridge and AP Bridge Mode Chapter 5 Management 5 1 SNMP Management The WNAP 7300 supports SNMP for convenient remote management Open SNMP Configuration in Management shown below Set the SNMP parameters and obtain MIB file before remote management Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Logout Status System Wireless Management Tools SNMP Configuration SNMP Configuration Firmware Upload l Use this page to set SNMP settings Configuration File Enable SNMP Password Settings Protocol Version Server Port Get Community public Set Community private Trap Destination 0 0 0 0 Trap Community public Configure SNMPv3 User Profile Figure 33 SNMP Configuration e Enable SNMP Check this box to enable SNMP settings a Protocol Version Select the SNMP v
24. ace cables when connecting to computer or peripheral devices Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the Following two conditions 1 This device may not cause harmful interference and 2 this Device must accept any interference received including interference that may Cause undesired operation Federal Communication Commission FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20 cm 8 inches during normal operation The availability of some specific channels and or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination The firmware setting is not accessible by the end user CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Energy Saving Note of the Device This power required device does not support Stand by mode operation For energy saving please press the power button or remove the DC plug to disconnect the device from the
25. bers of multicast groups Multicast traffic will only be forwarded to ports identified as members of the specific multicast group or groups Wireless Separation Wireless separation is an ideal way to enhance the security of network transmission Under the mode except wireless client mode enable Wireless Separation can prevent the communication among associated wireless clients RIFS RIFS Reduced Interframe Spacing is a means of reducing overhead and thereby increasing network efficiency Link Integration Available under AP Bridge AP Bridge mode it monitors the connection on the Ethernet port by checking Enabled lt can inform the associating wireless clients as soon as the disconnection occurs Max Station Num Available only under AP mode it defines the maximum amount of wireless clients allowed to be connected Space in Meter ACK Timeout To decrease the chances of data retransmission at long distance the WNAP 7300 can automatically adjust proper ACK timeout value by specifying distance of the two nodes Flow Control It allows the administrator to specify the incoming and outgoing traffic limit by checking Enable Traffic Shaping This is only available in Router mode Note We strongly recommend you leave most advanced settings at their defaults except Distance in Meters adjusted the parameter for real distance any modification on them may negatively impact the performance of your wireless netw
26. configuration please make sure your system meets the following requirements a A computer coupled with 10 100 Base TX adapter e Configure the computer with a static IP address of 192 168 1 x as the default IP address of the WNAP 7300 is 192 168 1 1 X cannot be 0 1 nor 255 a A Web browser on PC for configuration such as Microsoft Internet Explorer 6 0 or above Netscape or Firefox 3 3 How to Login the Web based Interface The WNAP 7300 provides you with user friendly Web based management tool a Open Web browser and enter the IP address Default 192 168 1 1 of the WNAP 7300 into the address field You will see the login page as below 802 11a n Outdoor Wireless Access Point Microsoft Internet Explorer File Edit View Favorites Tools Help EE Back O x a e Search Pp Favorites 2 d 3 Address 4 http 192 168 1 1 login asp v co inks gt PLANET MAAT 802 11a n Outdoor Wireless Access Point Name admin Password Internet Figure 14 Login Page Enter the username Default admin and password Default admin respectively and click Login to login the main page of the WNAP 7300 As you can see this management interface provides six main options in the black bar above which are Status System Wireless Management and Tools 15 802 11a n Outdoor Wireless Access Point Q PLANET Networking 4 Communication Status System Wireless Mana
27. dress Subnet Mask Gateway settings provided by your ISPs LAN Settings When DHCP Server is disabled users can specify IP address and subnet mask for the WNAP 7300 manually Make sure the specified IP address is unique on your network in order to prevent IP conflict When DHCP Server is enabled users may specify DHCP IP Address Range DHCP Subnet Mask DHCP Gateway and Lease Time 15 44640 minutes dk Warning a In AP mode the WNAP 7300 must establish connection with another wireless device before it is set to Router mode In Router mode it is impossible for users to access device via wired port for WAN is on wired port and LAN is on wireless port Users can access device through the wireless device connected with the WNAP 7300 a In wireless client mode users can access the WNAP 7300 via its wired port for WAN is on wireless port and LAN is on wired port when device is set to Router mode Bridge mode and AP Bridge mode are similar to AP mode when device is set to Router mode WAN is on wired port and LAN is on wireless port Thus users must also connect the WNAP 7300 with another wireless device before it is set to Router mode and access the WNAP 7300 via the connected wireless device 3 5 Time Settings Compliant with NTP the WNAP 7300 is capable of keeping its time in complete accord with the Internet time Make configuration in Time Settings from System To use this feature check Enable NTP Client Update
28. ersion and keep it identical on the WNAP 7300 and the SNMP manager e Server Port Change the server port for a service if needed however you have to use the same port to use that service for remote management a Get Community Specify the password for the incoming Get and GetNext requests from the management station By default it is set to public and allows all requests e Set Community Specify the password for the incoming Set requests from the management station By default it is set to private Trap Destination Specify the IP address of the station to send the SNMP traps to a Trap Community Specify the password sent with each trap to the manager By default it is set to public and allows all requests 5 1 1 Configure SNMPv3 User Profile For SNMP protocol version 3 you can click Configure SNMPv3 User Profile in blue to set the details of SNMPv3 user Check Enable SNMPv3 Admin User in advance and make further configuration PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management SNMP Configuration Configure SNMPv3 User Profile Firmware Upload MJ Enable SNMPv3Admin Configuration File User Name SNMPy3Admin Password eeccccce Password Settings Confirm Password eesccece Access Type Read Write Authentication Protocol HMDS vj Privacy Protocol None v Y Enable SNMPv3User VserName SNMP
29. gement Information Note Connections Flow Statistics ARP Table Bridge Table DHCP Clients The username and password are case sensitive and the password should be no more than 19 characters Information This page shows the current status and some basic settings of the device System Information Device Name MAC Address Country Region Firmware Version LAN Settings IP Address subnet Mask Gateway IP Address MAC Address Wireless Settings Operation Mode Wireless Mode SSID Channel Encryption TX Rate ACK Timeout VMM Enable Interface Status ap4e28a0 00 30 4f 4e 28 a0 United States 2 0 3 PL 1 192 168 1 1 255 255 255 0 0 0 0 0 00 30 4f 4e 28 a0 AP 802 11a n Wireless 149 Open System Auto 27 microsecond ON Figure 15 Main Page be 3 4 Basic System Settings For users who use the WNAP 7300 for the first time it is recommended that you begin configuration from Basic Settings in System shown below gt PLANET 802 11a n Outdoor Wireless Access Point Status System Wireless Management Basic Settings Basic Settings TCP IP Settings Use this page to configure the basic parameters of device Time Settings Device Settings RADIUS Settings Device Name ap4e28a0 max 15 characters and no spaces Firewall Settings MORE mode Bridge wl TS Ethernet 1 DataRate Auto e Ethernet 2 DataRate auto v
30. gure 6 Power on the device by PWR buttON ccccccocccnnccccocccnncccnonccnncnononcnnnononancnnnonnnancnnnnononnranonnnanons 7 Figure 7 Attach and fasten the removable cover cocccoooccccccocnncocoononoconcnononononcononnnnonnnnnnnonannnnonannnnennnnnnnss 8 Figure 3 Connect to POE IMC a 8 Figure 9 Complete Selari niena a eae iaaa a P n A aA ana a aa aiin 9 Figure 10 Remove the pugs asia dat co edes teen 10 Figure 11 Connect to external antenna cccccccoocncnncccnonnnnncnnnnnnnnnnnononcnnnnnnnnnnnnnnnnnncnnnnrnnnnrnnnnrnnnnnnnnnnnnns 10 Figure 12 Pole Mounting Step l astere e e ee EE e aE EES 11 Figure 13 Pole Mounting Sleep 2 erir a a ias 12 FOULE T4 ogm Pag Oria TA A O 15 FIQUre TS Man Paucar e A dede 16 Figure 16 Basic System SSUNGS zut o et o 17 Figure 17 TCP IP Settings Bridge occccccoconncnnccccocnonncnonancnnnonnnnnnnnnonnncnnnononannnnnonnnancnnnnonannrnnnnnnaneos 18 Figure 13 FGP AP Settings ROUE y eos 19 Figure 19 TIMeSEMNGS ate e ee ey 21 Figure 20 RADIUS SENGS ltd 22 Figure 21 Source IP Fendi ea oaie aer 23 Figure 22 Destinado dara 24 Figure 23 SOUlCE PON FINGIN esos at rf ide 24 Figure 24 Destination Port Fit rnG ui lid 25 Figure 25 Port Forwarding cccccccssscccceeseecceesececceseeecsaeeecsagseecesaseeessageeessaseeessueeeessageeesseeeesseaseeeess 26 PL uote hae cat nha ons val rs alan here abun ns ain cara dna unset sacs areata nae daa a ce daden 26 Figure 27 Basic Wireless Settings
31. he following licenses or distribution models or licenses or distribution models similar to any of the following 1 GNU s General Public License GPL or Lesser Library GPL LGPL 2 the Artistic License e g PERL 3 the Mozilla Public License 4 the Netscape Public License 5 the Sun Community Source License SCSL 6 the Sun Industry Source License SISL and 7 the Apache Software license 2 Limited Use Any Public Software provided under the agreement shall be subject to the licenses terms and conditions of its model Licensee hereby agrees to comply with the terms and conditions applicable to any such Public Software as set forth in its presentation on website 3 Limited Liability The supplier hereby express that the supplier shall have no liability for any costs loss or damages resulting from Licensee s breach of the terms and conditions applicable to use conversion or combination of the licensed software with or into Public Software 4 NO WARRANTY This program or licensed software is distributed in the hope that it will be useful but WITHOUT ANY WARRANTY THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH LICENSEE 5 Public Software Name and Description Table 3 Public Software Name and Description
32. hold the button for at least 5 seconds and then release it until the PWR LED gives a blink 5 5 Reboot You can reboot your WNAP 7300 from Configuration File in Management as below Click Reboot and hit Yes upon the appeared prompt to start reboot process This takes a few minutes gt PLANET 802 11a n Outdoor Wireless Access Point System Wireless Management SNMP Configuration Configuration File This page allows you to save current settings to a file or load the settings from the file which was h saved previously Besides you could reset the current configuration to factory default or reboot Configuration File the device Firmware Upload Password Settings Save Settings to File Load Settings from File Browse Upload Reset Settings to Default Reboot The Device Figure 38 Reboot 5 6 Password From Password Settings in Management you can change the password to manage your WNAP 7300 Enter the new password respectively in New Password and Confirm Password fields click Apply to save settings J PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management SNMP Configuration Password Settings Firmware Upload Use this page to set the password of this Access Point Configuration File New Password Confirm Password Password Settings gt
33. ient mode could be enhanced greatly with this option enabled however if your wireless clients don t support A MPDU A MSDU aggregation it is not recommended to enable it Short Gl Under 802 11n mode enable it to obtain better data rate if there is no negative compatibility issue RTS Threshold The WNAP 7300 sends RTS Request to Send frames to certain receiving station and negotiates the sending of a data frame After receiving an RTS that STA responds with a CTS Clear to Send frame to acknowledge the right to start transmission The setting range is O to 2346 in byte Setting it too low may result in poor network performance Leave it at its default of 2346 is recommended Fragmentation Length Specify the maximum size in byte for a packet before data is fragmented into multiple packets Setting it too low may result in poor network performance Leave it at its default of 2346 is recommended Beacon Interval Specify the frequency interval to broadcast packets Enter a value between 20 and 1024 DTIM Interval DTIM which stands for Delivery Traffic Indication Message is contained in the data packets It is for enhancing the wireless transmission efficiency The default is set to 1 Enter a value between 1 and 255 IGMP Snooping IGMP snooping is the process of listening to IGMP network traffic By enabling IGMP snooping the AP will listen to IGMP membership reports queries and leave messages to identify the ports that are mem
34. ing Dst Port Filtering Port Forwarding DMZ Setting gt gt Figure 26 DMZ 3 8 Basic Wireless Settings Open Basic Settings in Wireless as below to make basic wireless configuration Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management Basic Settings Wireless Basic Settings Security Settings l l Use this page to configure the parameters for wireless LAN clients which may connect to your i Access Point Here you may change wireless mode as well as wireless network parameters Advanced Settings Access Control O Disable Wireless LAN Interface Wireless Mode fap Wireless Network Name WDS Settings SSID Wireless Broadcast SSID O Enabled Disabled 802 11 Mode 802 11a n Y HT protect O Enabled Disabled Channel Number 149 Y Antenna Internal 16 dBi SMA Connector Output Power Ful Data Rate Auto Y Channel mode 20MHZ Extension channel protection mode None Figure 27 Basic Wireless Settings Disable Wireless LAN Interface Check this option to disable WLAN interface then the wireless module of the WNAP 7300 will stop working and no wireless device can connect to it Wireless Mode Four operating modes are available on the WNAP 7300 AP The WNAP 7300 establishes a wireless coverage and receives connectivity from other wireless devices Wireless
35. lone Available only under wireless client mode it hides the MAC address of the WNAP 7300 while displays the one of associated wireless client or the MAC address designated manually 3 9 Site Survey Under wireless client mode the WNAP 7300 is able to perform site survey through which information on the available access points will be detected Open Basic Settings in Wireless by clicking the Site Survey button beside Wireless Mode option the wireless site survey window will pop up with a list of available wireless networks around Select the AP you would like to connect and click Selected to establish connection The wireless site survey window can also be viewed by opening the Site Survey page in Tools A http 192 168 1 1 Wireless Site Survey Microsoft Internet Explorer Wireless Site Survey This page provides tool to scan the wireless network If any Access Point or IBSS is found you could choose to connect it manually when client mode is enabled Signal Strength FO wnap 7300 2 149 00 30 4f 30 52 00 ain A8 NONE Select SSID Channel MAC Address Wireless Mode Security DD Internet Figure 28 Site Survey Chapter 4 Advanced Settings 4 1 Advanced Wireless Settings Open Advanced Settings in Wireless to make advanced wireless settings Y PLANET 802 11a n Outdoor Wireless Access Point wt pi AP y Networking amp Communication Status System
36. mmunication Status System Wireless Management Information Association List This table shows the MAC Address IP Address and RSSI for each associated wireless client Connections Flow Statistics ARP Table ee 0 0 0 0 2010 10 8 14 27 56 Bridge Table DHCP Clients Figure 44 Connection 6 3 View Network Flow Statistics Open Flow Statistics in Status to check the data packets received on and transmitted from the wireless and Ethernet ports Click Refresh to view current statistics gt PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status system Wireless Management Information Flow Statistics This page shows the packet counters for transmission and reception regarding to wireless and Ethernet networks Connections Flow Statistics gt gt ARP Table Poll Interval 5 0 8 8534 sec _Set Interval Bridge Table Received Transmitted DHCP Clients Unicast Packets 0 0 Broadcast Packets 0 0 Multicast Packets 0 D Total Packets 0 0 Total Bytes 0 0 Received Transmitted Total Packets 7013 3309 Total Bytes 679845 955965 Received Transmitted Total Packets 0 0 Total Bytes 0 0 Figure 45 Network Flow Statistics a Poll Interval Specify the refresh time interval in the box beside Poll Interval and click Set Interval to save settings Stop help
37. n the drop down list according to your situation Antenna By default the WNAP 7300 uses its built in antenna for directional transmission however if you prefer to use an external antenna for your case dependent applications you can switch from Internal 16 dBi to SMA Connector Note You are able to choose SMA Connector only from the WEB UI when you have well done installing the external antenna otherwise it might damage the unit itself Output Power Specify the signal transmission power The higher the output power is the wider the signal can cover but the power consumption will be greater accordingly Usually Full is preferred Data Rate Usually Auto is preferred Under this rate the Wireless Outdoor WNAP 7300 will automatically select the highest available rate to transmit In some cases however like where there Is no great demand for speed you can have a relatively low transmit rate for compromise of a long distance Channel Mode Four levels are available 20MHz and 40MHz The last one can enhance data throughput but it takes more bandwidth thus it might cause potential interference Extension Channel Protection Mode This is to avoid conflict with other wireless network and boost the ability of your device to catch all legacy devices transmissions However it may decrease wireless network performance Compared to CTS Self the transmission amount of CTS RTS is much lower Enable MAC C
38. ned IP address MAC address and time expired for each DHCP leased client Connections Flow Statistics ARP Table Bridge Table DHCP Clients gt Figure 48 DHCP Client Table Chapter 7 Troubleshooting This chapter provides troubleshooting procedures for basic problems with the WNAP 7300 For warranty assistance contact your service provider or distributor for the process Q 1 How to know the MAC address of the WNAP 7300 MAC Address distinguishes itself by the unique identity among network devices There are two ways available to know it e Each device has a label posted with the MAC address which located in the back of the device e On the WNAP 7300 s Web based management interface you can view the MAC Address from View Basic Information Q 2 What if would like to reset the unit to default settings You may restore factory default settings in Configuration File from Management Q 3 What if would like to backup and retrieve my configuration settings You may do the backup by generating a configuration file or retrieve the settings you have backed up previously in Configuration File from Management Q 4 What if can not access the Web based management interface Please check the followings e Check whether the power supply is OK Try to power on the unit again e Check whether the IP address of PC is correct in the same network segment as the unit e Login the unit via
39. ng sleeved shirt or jacket 5 When the system is operational avoid standing directly in front of it Strong RF fields are present when the transmitter is on 2 1 3 Installation Precautions To keep the WNAP 7300 well while you are installing it please read and follow these installation precautions 1 Users MUST use a proper and well installed surge arrestor with the WNAP 7300 otherwise a random lightening could easily cause fatal damage to the unit EMD Lightning DAMAGE IS NOT COVERED UNDER WARRNTY 2 Users MUST use the Power cord POE Injector shipped in the box with the WNAP 7300 Use of other options will cause damage to the unit 3 Users MUST power off the WNAP 7300 first before connecting the external antenna to it Do not switch from built in antenna to the external antenna from WEB management without physically attaching the external antenna onto the WNAP 7300 otherwise damage might be caused to the device itself 2 1 4 Product Package The product package you have received should contain the following items e The WNAP 7300 x 1 Pole Mounting Ring X2 PoE Injector x 1 Power Adapter x 1 Quick Installation Guide QIG x 1 e Product CD User s Manual amp QIG included X 1 Note e lf any of them are not included or damaged please contact your local vendor for support Pole Mounting Ring dh Warning e Users MUST use the Power Adapter amp POE Injector shipped in the box
40. nnnnconnnccocccoonccannncnnnncnnnnnnnnncnnrrnnnnnnnnnnnrnrrrnnnnnnnnrnrrrnnnnannn 3 2 1 Preparation berore INSANIHON ensen didas dd E 3 2 1 1 Professional Installation Required ccooonccccoconnncccocnonoconnonononnnonononnnconnnnononnanncononcnnnnnananess 3 22 Sale PLECAUILIOINS seo amet cate ee ace a ea ipbcid 3 2 1 3 Installation PreCcautiONS ccoocccccocnccccnncocononononncnnnnnononononnnnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnnnncnnnnnos 4 UE ios Me CE 4 22 HardWare nstallati enan e ad ande 6 ZAN CONNEC TUD gat hela etic ste lard ives hs tt taal rine a a 6 222 Usno ines External Amten usa a eked 10 2230 FOIS MOUNUN tetesa natten a Savin enden a a orcas swans 11 Chapter 3 Basic SOI Sian a 13 3 1 Factory Deau Seting S osito lidad 13 3 2 OV SIEM MOCUINCINGINS niendo lei alce cia idas 14 3 3 How to Login the Web based Interface oooonccccccccnnconccocoonconnonnonncnnnonnncnnononancnnnononancnnnononanenss 14 3 4 Basic System oeg acesa aseos Ene Ets essa lata 17 SS A CE ee 20 3 0 RADIUS SONGS cities 21 3 IRC Wall Settings a a es o e dl eeen eden ade 23 38 Basie WIEN o 27 A eeen benen sedis tiaccan ode nee neben santen nlet 30 Chapter 4 Advanced Settings aiii ib eeden iedeen inden anken ene eaaa a 31 4 1 Advanced Wireless SettingS ccccccocconocccnncconocconnnnnnnnnnnocnannnnnononononnannnnnnnnnononnnnnnnnnnnnnnonananess 31 4 2 Wireless Security SENOS rr renee AS 34 A 2 Ne SO CUPILY SOLUS E a enne 34
41. ntrol Mode Disable vi WDS Settings MAC Address MAC Address Select Figure 31 Access Control Access Control Mode If you select Allow Listed only those clients whose wireless MAC addresses are in the access control list will be able to connect to your AP While when Deny Listed is selected those wireless clients on the list will not be able to connect the AP a MAC Address Enter the MAC address of the wireless client that you would like to list into the access control list click Apply then it will be added into the table at the bottom Delete Selected All Check the box before one or more MAC addresses of wireless client s that you would like to cancel and click Delete Selected or Delete All to cancel that access control rule 4 2 3 WDS Settings Extend the range of your network without having to use cables to link the bridges by using the Wireless Distribution System WDS Simply put you can link the bridges wirelessly Open WDS Settings in Wireless as below Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management Basic Settings WDS Settings Wireless Distribution System uses wireless media to communicate with other APs like the Ethernet does To do this you must set these APs in the same channel and set MAC addresses of Advanced Settings other APs which you want to communicate with in the t
42. oot If the ping timeout packets reached the value the WNAP 7300 will reboot automatically Chapter 6 Status 6 1 View Basic Information Open Information in Status to check the basic information of the WNAP 7300 which is read only Click Refresh at the bottom to have the real time information Y PLANET Networking 4 Communication 802 11a n Outdoor Wireless Access Point Status System Wireless Management Information gt gt Information This page shows the current status and some basic settings of the device Connections Flow Statistics System Information ARP Table Bridge Table DHCP Clients Device Name MAC Address CountryRegion Firmware Version LAN Settings IP Address Subnet Mask Gateway IP Address MAC Address Wireless Settings Operation Mode Wireless Mode SSID Channel Encryption TX Rate ACK Timeout WM Enable Interface Status Figure 43 Basic Information ap4e28a0 00 30 4f 4e 28 a0 United States 2 0 3 PL 1 192 168 1 1 255 255 255 0 0 0 0 0 00 30 4f 4e 28 a0 AP 802 11a n Wireless 149 Open System Auto 27 microsecond 6 2 View Association List Open Association List in Connection from Status to check the information of associated wireless clients All is read only Click Refresh at the bottom to view the current association list Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Co
43. ork 4 2 Wireless Security Settings To prevent unauthorized radios from accessing data transmitting over the connectivity the WNAP 7300 provides you with rock solid security settings 4 2 1 Security Settings Open Security Settings in Wireless as below Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management Basic Settings A Security Settings Security Settings gt gt Custom WLAN s security profile settings Advanced Settings Network Authentication Access Control Data Encryption WDS Settings Key Type Default Tx Key WEP Passphrase WPA amp WPA2 with Radius WPA PSK WPA amp 2 PSK Encryption Key 1 WPA PSKSWPA2 PSK Encryption Key 2 Encryption Key 3 Encryption Key 4 Apply cancel Figure 30 Security Settings e Network Authentication Open System lt allows any device to join the network without performing any security check Shared Key Data encryption and key are required for wireless authentication Legacy 802 1x As an IEEE standard for port based Network Access Control it provides the rights to access the wireless network and wired Ethernet With User and PC identity centralized authentication as well as dynamic key management it controls the security risk of wireless network to the lowest To serve the 802 1x at least one EAP type should be supported by the RADIUS Server AP and
44. os cache on the client computer by running the nbtstat r command before using the device name of the WNAP 7300 to access its Web Management page Use Fixed IP Address Check this option You have to specify a static IP address subnet mask default gateway and DNS server for the WNAP 7300 manually Make sure the specified IP address is unique on your network in order to prevent IP conflict If the WNAP 7300 is configured as Router mode you need to configure some additional TCP IP parameters for accessing the Internet PLANET 802 11a n Outdoor Wireless Access Point Status System Wireless Management Basic Settings TCP IP Settings TCP IP Settings B Use this page to configure the parameters for local area network which connects to the LAN port of your Access Point Here you may change the setting for IP address subnet mask DHCP etc Time Settings nn RADIUS Settings WAN Settings Firewall Settings WAN Access Type IP Address Subnet Mask 255 255 255 0 Default Gateway 1192 168 0 254 DNS 1 0 0 0 0 DNS 2 0 0 0 0 LAN Settings IP Address 192 168 1 1 Subnet Mask 255 255 255 0_ DHCP Server Disabled DHCP IP Address Range 192 168 11 1921681200 Lease Time E 20 15 44640 Minutes Figure 18 TCP IP Settings Router WAN Settings Specify the Internet access method to Static IP DHCP or PPPOE Users must enter WAN IP Ad
45. other browsers such as Firefox e Hardware reset the unit Q 5 In wireless client mode what if the wireless connection is not stable after associating with an AP e Since the WNAP 7300 comes with a built in directional antenna it is recommended make it face to the direction where the AP is to get the best connection quality e In addition you can start Site Survey in Wireless Basic Settings to check the signal strength If it is weak or unstable The smaller the number is the weaker the signal strength is please join other available AP for better connection Appendix A ASCII WEP can be configured with a 64 bit 128 bit or 152 bit Shared Key hexadecimal number or ACSII As defined hexadecimal number is represented by 0 9 A F or a f ACSII is represented by 0 9 A F a f or punctuation Each one consists of two digit hexadecimal Table 2 ACSII ASCII Hex ASCII Hex ASCII Hex ASCII Hex Character Equivalent Character Equivalent Character Equivalent Character Equivalent NO O Co al bh N NO ev Ol N O N ee ev dl ev N N ce al K O O N al oO al O1 N O ev O1 O O m N N ev 7 dl N O Ti NO 00 S O dal 00 N O N de iN mb O1 de N NO iN NO O1 N N NO iN ice dal N ce N EN NO m D O dal N O N TI D N dal N N ice O iN 00 N 00 ce iN de O mb N de oP NO A A O al N Ce O
46. pgrade the device firmware to a new version Please do not power off the device during the upload because it may crash the system geleer Ge Figure 35 Upgrade Firmware a Click Browse to select the firmware file you would like to load 5 Click Upload to start the upload process a Wait a moment the system will reboot after successful upgrade k Note Do NOT cut the power off during upgrade otherwise the system may crash 5 3 Backup Retrieve Settings It is strongly recommended you back up configuration information in case of something unexpected If tragedy hits your device you may have an access to restore the important files by the backup All these can be done by the local or remote computer Open Configuration File in Management as below PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management SNMP Configuration r Configuration File This page allows you to save current settings to a file or load the settings from the file which was A ke saved previously Besides you could reset the current configuration to factory default or reboot Configuration File gt gt the device Firmware Upload Password Settings 2 Save Settings to File Load Settings from File Upload Reset Settings to Default Reboot The Device Figure 36 Backup Retrieve Settings a Save Settings to File By clicking Save a dialog box
47. power circuit Without power off or remove the DC plug the device still consuming power from the power circuit In the view of Saving the Energy and reduce the unnecessary power consuming it is strongly suggested to power off or remove the DC plug for the device if this device is not intended to be active Protection requirements for health and safety Article 3 1a Testing for electric safety according to EN 60950 has been conducted These are considered relevant and sufficient Protection requirements for electromagnetic compatibility Article 3 1b Testing for electromagnetic compatibility according to EN 301 489 1 EN 301 489 17 and EN 55024 has been conducted These are considered relevant and sufficient Effective use of the radio spectrum Article 3 2 Testing for radio test suites according to EN 300 328 2 has been conducted These are considered relevant and sufficient CE in which Countries where the product may be used freely Germany UK Italy Spain Belgium Netherlands Portugal Greece Ireland Denmark Luxembourg Austria Finland Sweden Norway and Iceland France except the channel 10 through 13 law prohibits the use of other channels Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment All guidelines of this and of
48. r local network to Internet through the WNAP 7300 Use of such filters can be helpful in securing or restricting your local network Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication status System Wireless Management Basic Settings Destination Port Filtering TCP IP Settings Entries in this table are used to restrict certain ports of data packets from your local network to R Internet through the Gateway Use of such filters can be helpful in securing or restricting your Time Settings local network RADIUS Settings O Enable Destination Port Filtering Firewall Settings Port Range a Protocol Both Src IP Filtering Dst IP Filtering Sre Port Filtering Dst Port Filtering Port Forwarding L Delete Selected j Delete All DMZ Setting Figure 24 Destination Port Filtering Port Forwarding The port forwarding allows you to automatically redirect common network services to a specific machine behind the NAT firewall These settings ne are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind the router s NAT firewall PLANET Networking amp Communication status Basic Settings TCP IP Settings Time Settings RADIUS Settings Firewall Settings Src IP Filtering Dst IP Filtering Src Port Filtering Dst Port Filtering Port Forwarding
49. s to stop the auto refresh of network flow statistics 6 4 View ARP Table Open ARP Table in Status as below Click Refresh to view current table Networking amp Communication Logout Y PLANET 802 11a n Outdoor Wireless Access Point Status System Wireless Management Tools Information ARP Table This table shows ARP table Connections Flow Statistics PATO AA IP Address MAC Address Interface 192 168 1 100 00 11 D8 70 FF 84 bi ARP Table Bridge Table DHCP Clients Figure 46 ARP Table 6 5 View Bridge Table Open Bridge Table in Status as below Click Refresh to view current connected status Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management Information Bridge Table This table shows bridge table Connections Flow Statistics ARP Table 00 30 4f 4e 268 a0 Bridge Bridge Table 00 11 d8 70 f 84 LAN 0 00 DHCP Clients Figure 47 Bridge Table 6 6 View Active DHCP Client Table Open DHCP Client List in Status as below to check the assigned IP address MAC address and time expired for each DHCP leased client Click Refresh to view current table Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management Information DHCP Clients This table shows the assig
50. the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment _ WEEE Regulation XI To avoid the potential effects on the environment and human health as a O result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision User s Manual for PLANET 802 11a n Outdoor Wireless CPE AP Router Model WNAP 7300 Rev 1 0 January 2011 About This Manual This user manual is intended to guide professional installer to install the WNAP 7300 and how to build the infrastructure centered on it lt includes procedures to assist you in avoiding unforeseen problems Conventions For your attention on important parts special characters and patterns are used in this manual a Note This indicates an important note that you must pay attention to ele Warning This indicates a warning or caution that you have to abide Bold Indicates the function important words and so on Content Chapter HU INtOdU CU ON daa 1 MST ARTO GUC TOM art ras 1 WO DC AIAG Samir drid 1 AS A E y baceaai tains edecharaaeoushathohs saua tbucaaebeo gna en taceanian 2 14 PY DIGAl AD DIICANON dt AAA AA AA 2 Chapter 2 Hardware Installation ooonooncccccccc
51. this page to set the radius server settings TCP IP Settings Time Settings Authentication RADIUS Server RADIUS Settings IP Address 0 0 0 0 Firewall Settings Port 1812 Reauthentication Time 3600 Seconds O Global Key Update every 3600 Seconds Figure 20 RADIUS Settings a Authentication RADIUS Server This is for RADIUS authentication It can communicate with RADIUS through IP Address Port and Shared Secret IP Address Enter the IP address of the Radius Server Port Enter the port number of the Radius Server Shared Secret This secret which is composed of no more than 31 characters is shared by the AP and RADIUS during authentication Re authentication Time Set the time interval between two authentications Global Key Update Check this option and specify the time interval between two global key updates 3 7 Firewall Settings The firewall is a system or group of systems that enforce an access control policy between two networks lt may also be defined as a mechanism used to protect a trusted network from an un trusted network The WNAP 7300 has capabilities of Source IP Filtering Destination IP Filtering Source Port Filtering Destination Port Filtering Port Forwarding as well as DMZ This is available only under Router Mode Source IP Filtering The source IP filtering gives users the ability to restrict certain types of data packets from your local network to Internet through the WNAP
52. urce port filtering enable you to restrict certain ports of data packets from your local network to Internet through the WNAP 7300 Use of such filters can be helpful in 802 11a n Outdoor Wireless Access Point System Wireless Management Destination IP Filtering Entries in this table are used to restrict the computers in LAN from accessing certain websites in WAN according to IP address O Enable Destination IP Filtering ft Destination IP Address Comment Delete Selected Delete all Figure 22 Destination IP Filtering securing or restricting your local network Y PLANET Networking 4 Communication Status Basic Settings TCP IP Settings Time Settings RADIUS Settings Firewall Settings Sre IP Filtering Dst IP Filtering Sre Port Filtering Dst Port Filtering Port Forwarding System DMZ Setting Destination Port Filtering The destination port filtering enables you to restrict certain ports of data 802 11a n Outdoor Wireless Access Point Wireless Management Source Port Filtering Entries in this table are used to restrict certain ports of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network C Enable Source Port Filtering Part Range Protocol Both Y Comment Delete Selected Delete all Refresh Figure 23 Source Port Filtering packets from you
53. v3User Password socccoss Confirm Password eeeeeeee Access Type Read Only i Authentication Protocol MDS Privacy Protocol None Ki Figure 34 Configure SNMPv3 User Profile User Name Specify a user name for the SNMPv3 administrator or user Only the SNMP commands carrying this user name are allowed to access the WNAP 7300 Password Specify a password for the SNMPv3 administrator or user Only the SNMP commands carrying this password are allowed to access the WNAP 7300 e Confirm Password Input that password again to make sure it is your desired one a Access Type Select Read Only or Read and Write accordingly Authentication Protocol Select an authentication algorithm SHA authentication is stronger than MD5 but is slower e Privacy Protocol Specify the encryption method for SNMP communication None and DES are available None No encryption is applied DES Data Encryption Standard it applies a 58 bit key to each 64 bit block of data 5 2 Upgrade Firmware Open Firmware Upload in Management and follow the steps below to upgrade firmware locally or remotely through the WNAP 7300 s Web SY PLANET Networking 4 Communication Status SNMP Configuration Firmware Upload Configuration File Password Settings 802 11a n Outdoor Wireless Access Point Logout system Wireless Management Tools Upgrade Firmware This page allows you u
54. wireless client WPA with_RADIUS With warrant username password and etc offered by user this kind of authentication can be realized with specific RADIUS server This is the common way to be adopted in large enterprise network WPA2 with RADIUS As a new version of WPA only all the clients support WPA2 can it be available If it is selected AES encryption and RADIUS server is required WPA amp WPA2 with RADIUS It provides options of WPA TKIP or WPA2 AES for the client If it is selected the data encryption type must be TKIP AES and the RADIUS server must be set WPA PSK It is a simplified WPA mode with no need for specific authentication server In this so called WPA Pre Shared Key all you have to do is just pre enter a key in each WLAN node and this is the common way to be adopted in large and middle enterprise as well as residential network WPA2 PSK As a new version of WPA only all the clients support WPA2 can it be available If it is selected the data encryption can only be AES and the passphrase is required WPA PSK amp WPA2 PSK It provides options of WPA TKIP or WPA2 AES encryption for the client If it is selected the data encryption can only be TKIP AES and the passphrase is required Data Encryption If data encryption is enabled the key is required and only sharing the same key with other wireless devices can the communication be established None Available only when the authentication type is open system
55. with the WNAP 7300 Use of other options will cause damage to the unit 2 2 Hardware Installation 2 2 1 Connect up 1 The bottom of WNAP 7300 is a movable cover Loosen the screw with a Phillips screwdriver Grab the cover and pull it out as the figure shown below Figure 3 Move the Cover 2 Plug a standard Ethernet cable into the RJ45 port labeled LAN 1 Do not plug the cable into the RJ45 port labeled LAN 2 Figure 4 Cable Connection The secondary Ethernet port labeled LAN 2 is for IP video integration To use it you need to enable the secondary port in advance before connecting with the IP camera from the WNAP 7300 s Web Management as shown below Y PLANET 802 11a n Outdoor Wireless Access Point Networking amp Communication Status System Wireless Management Basic Settings Basic Settings TCP IP Settings Use this page to configure the basic parameters of device Time Settings Device Settings Device Name ap4e2820 max 15 characters and no spaces cisions Settings nian GRE Ethernet 1 DataRate ato wl Ethernet 2 DataRate Country Region Spanning Tree Enabled Disabled STP Forward Delay 1 30 seconds RADIUS Settings Figure 5 Enable the Secondary RJ45 Power Press the black PWR button beside the LAN 1 Ethernet port Figure 6 Power on the device by PWR button 4 Attach and fasten the removable cover to the bottom of the WNAP 73
Download Pdf Manuals
Related Search