Mimaki JV3
Contents
1. www nazdar com AR Requirements e Full set of Lyson 1300 Series Inkset cartridges 2 x CMYK or 1 x CMYKLcLm Plus 2 x Cleaning Cartridges Step 1 Before commencing with the ink conversion it is essential you obtain a good nozzle check procedure for performing nozzle check is in appendix 1 No warranty dispute regarding the conversion can be supported or defended if a pre nozzle check is not supplied If several nozzles are permanently missing even after several cleans you can proceed providing the customer agrees to signing a disclaimer stating the condition of the nozzle check before conversion A copy of the disclaimer is located in appendix 2 of this conversion procedure Empty waste bottle before commencing this is usually located on the underside on the printer Dispose of the ink safely as guided in your Mimaki user manual Consult your user manual if you are unsure of the waste tanks location Step 2 Next remove each Mimaki SS2 cartridge one by one replacing with the Lyson 1300 series inkset taking care that the colour removed is replaced with the identical colour from the Lyson series inkset If a bulk feed system or refillable system is being used please refer to next page If a cartridge fails to install correctly consult the Cartridge fails to install section in appendix 1 Make sure the printer is in Local mode An explanation on Local Remote mode and the display panel is explained2. Department Www nazdar com
3. machine Return to the conversion procedure Www nazdar com Appendix 1 JOG keys a v lt gt They are used to shift the carriage X and the medium under the LOCAL mode In addition they are used to select a set value HEATER key Used to set the temperature of the printer heater and preheater and check the current tempera ture of the platen FUNCTION key Enter to the setting function menu END key Used to cancel the last set item that TEST amp CLEANING key Plots the test pattern for checking Display Displays a set item a guidance f error etc POWER lamp It lights up in green when the power to the device is tumed on DATA CLEAR key Erase the data has been received REMOTE key Change the operation mode between the REMOTE mode and the LOCAL mode ENTER key Used to move to the lower level menu and establish the settings has been input or to return to the Nozzle clogging and performs previous selling menu head cleaning when ink clogging occurs Local Remote Mode Selection Press the Remote key to toggle between Local and Remote mode Performing a Nozzle Test Print Press the Test amp Cleaning key once in local mode When Test Draw is displayed on the display panel press Enter Key Press End key to return to Local mode after the print has finished Performing a Clean Function Press the Test amp Cleaning key t
4. ance procedure as documented in your Mimaki user manual Failure to do so may cause irreparable damage to your printer There is a guide on the procedures in appendix 1 for basic maintenance www nazdar com The use of a bulk feed system or refillable cartridges Triangle or similar bulk feed system Pinch clips to stop flow of ink Complete a nozzle test print to insure that all nozzles are firing properly Note any defective nozzles Print control images with the existing ink system Power down machine Close ink lines pinch control located below the bulk ink tanks Disassemble ink line at bulk ink tank Open the bulk ink tank cap and drain the bulk ink tank and ink lines of existing ink system Clean any remaining ink in the bulk ink tank with DCA04 solvent and deposit into an appropriate waste container Assemble bulk ink tank onto stand and reattach the ink lines Secure ink tanks into place and fill each tank with approximately 34 of ink from the Lyson 1300 litre container 10 Close bulk ink tank cap 11 Return back to the conversion procedure Pet Oe eee Refillable cartridges Complete a nozzle test print to insure that all nozzles are firing properly Note any defective nozzles Print control images with the existing ink system Remove the ink cartridges from the machine and drain the existing ink from the cartridges Fill the Lyson 1300 inks into the cartridges to about 3 4 full Place the cartridges into the
5. fi AR Ver 3 0b May 2007 Ink conversion procedure Mimaki J V3 Converting from Mimaki SS2 to Lyson 1300 Series Inkset Www nazdar com Rev 2 0 May 2007 THIS DOCUMENT MAY NOT IN WHOLE OR IN PART BE COPIED STORED ELECTRONICALLY OR COMMUNICATED TO A THIRD PARTY WITHOUT WRITTEN AGREEMENT OF NAZDAR Nazdar reserves the right to make changes without notice to the specifications and materials herein and shall not be responsible for any damages including consequential caused by reliance on the materials presented including but not limited to typographical arithmetic or listing errors Please address any questions comments and suggestions to your nearest Nazdar Technical service department USA Nazdar 8501 Hedge Lane Terrace Shawnee KS 66227 U S A Ph 1 913 422 1888 Fax 1 913 422 2296 www nazdar com E mail custserv nazdar com Europe Middle East and Asia Nazdar Ltd Barton Road Heaton Mersey Stockport Cheshire SK4 3EG United Kingdom Ph 44 161 442 2111 Fax 44 161 442 2611 www nazdar com E mail technicalserviceuk nazdar com Www nazdar com IMPORTANT I NFORMATION TO READ BEFORE PROCEEDING WITH YOUR INSTALL The following conversion procedure is designed to convert over your Mimaki printer to Lyson 1300 series inkset whether 4 or 6 colour The Lyson 1300 series inkset has been specifically formulated to be a fully compatible colour match thereby alleviating the need to flush t
6. he cartridge is a new cartridge and not a used or empty cartridge and it has a chip on the side 5 If all of the above fail to rectify the issue consult your nearest Nazdar Technical Department A list of your nearest Nazdar Technical department is listed on page 2 Www nazdar com Reference of Ink cartridge Installation 4 color ink set e color ink set Front side rE Head 2 Head 3 Head 4 4 color ink set Two ink cartridges for each color 6 color ink set One ink cartridge of each color Set the washing fluid cartridges SPC 0352 for the left spaces of ink station Preventative Maintenance Measures Gently wipe down around the cap station and the wiper arm any dried ink which may contaminate the new setup Using a swab and some of the Lyson flush solution gently wipe down the area around the cap station followed by wiping down the wiper blade and underneath the carriage on the fascia of the printheads Dispose of any gloves swabs and empty cartridges used during the conversion in a proper manner Recommended parts to perform general maintenance Latex Gloves Safety glasses Cleaning Swabs Lint free cloths Lyson 1300 Flush Solution NOTES The cartridges used in the preparation do not signify that these are the Ink Cleaning cartridges used during your procedure They have merely been used to assist putting this document together Any further issue please contact your nearest Nazdar Technical
7. he printer or generate new profiles Failure to proceed with the correct method may cause damage to your printer Nazdar cannot be held responsible due to lack of care during this procedure If you require any further information on what method you need to perform please contact your nearest Nazdar technical service department for further information or instruction The list of your nearest Nazdar technical team can be found on page 2 of the conversion procedure To ensure safe Use Pictorial Signs Pictorial Signs are used to as a visual reference throughout the industry to quickly inform everybody of a certain safe practise that is needed to be carried out or to warn of pending danger For your own Safety wear safety glasses This symbol indicates a prohibited behaviour refrain from doing This symbol gives you a caution advising of possible error or harm For your own Safety wear safety gloves gt e When handling ink containers be careful that ink does not get in your eyes or on any e your skin However if this happens flush immediately with water Otherwise 8 r your eyes may become congested or inflamed slightly If you feel discomfort a r consult a doctor immediately m e Do not disassemble ink Containers Otherwise ink may get in your eyes or on i your skin e Only use Nazdar Lyson Solvent ink and appropriate cleaning liquid Using other ink E g dye or pigment will cause permanent damage to the printer 3
8. in Appendix 1 On the display screen the Function button can be seen Press the Y key until ee is Displayed Once displayed Press the Enter key Www nazdar com AR Step 4 Next press the w key until is Displayed Again press the Enter key E The printer will now perform an ink fill This will automatically replace the Mimaki SS2 inks with your new Lyson 1300 series inkset through the ink lines and takes approx 3 5 minutes to perform Once the ink fill has finished press the Enter key once more to repeat the process You have almost completed the conversion Step 5 When the second ink fill has finished revert it back to LOCAL mode by pressing the End KEY until Local is again displayed in the display screen You need to perform a nozzle test print and compare it against the nozzle test print previously performed with the Mimaki SS2 inkset If there are nozzles missing which were present before the ink conversion perform a strong clean The method to perform a clean is explained in appendix 1 Again perform a nozzle test print Repeat this procedure until all the nozzles are restored If you fail to restore any nozzles lost during the conversion procedure consult your nearest Nazdar technical support team as shown on page 2 for further instruction and guidance Even though you have converted your Mimaki printer to Lyson 1300 series inkset you must still carry out the general mainten
9. wice in local mode Cleaning and Type will be displayed on the display panel Pressing the w key will switch between Normal Strong or Soft clean Select the strength of clean you require and press Enter After the clean has finished press End to return to Local mode Cartridge fails to install 1 Check the cartridge is being inserted into the correct cartridge slot 2 Check the chip on the side of the cartridge is clean from any grease Gently wipe the chip surface with some alcohol and a lint free cloth Make sure the chip is fully dry before reinserting it into the cartridge slot 3 Has the cartridge size been changed i e 220ml 440ml or Vis versa If you were previously running 220ml cartridges and you have changed to 440ml you will need to reset the new cartridge size on the display panel 220ml cartridges are set as SS Sol in the menu system 440ml cartridges are set as SS2 Sol To allow the change the printer has to be reset to read the new cartridge from SS Sol4 or 6 to SS2 sol4 or SS2 sol6 Sol4 and Sol6 being 4 or 6 colour This function is found within the maintenance mode on the display panel The procedure for changing between SS2 lt gt SS inks is located in maintenance mode Press Function key in Local mode When Maintenance is displayed Press Enter Key Next press v key until SS2 lt gt SS CHG lt ENT gt is displayed Pressing Enter toggles between the two options 4 Make sure t
Download Pdf Manuals
Related Search