DEMOQE8 User Manual 1_01.book
Contents
1. 19 7 1 System Power 19 7 2 RS232 Communications 21 7 3 LED Display Port 23 7 4 Input and Reset Switches 23 7 5 3 Axis Accelerometer Jumper Settings 25 7 6 Buzzer 27 7 7 IIC Pull up 27 7 8 Analog Input Potentiometer 28 7 9 Optional External Crystal Circuitry Jumper Enable 28 7 10 Optional Jumpers For Various VDD And VSS 28 8 DEMO9S08QE8 CODE DEVELOPMENT SOFTWARE 29 8 1 Using CodeWarrior With The DEMO9S08QE8 29 8 2 Using P amp E Software With The DEMO9S08QE8 29 9 TRANSITIONING TO YOUR OWN TARGET2. 29 9 1 Hardware Solutions At A Glance 30 9 2 Working With P amp E s USB Multilink 31 9 3 Working With P amp E s Cyclone PRO 32 10 TROUBLESHOOTING 33 10 1 DEMO9S08QE8 Is Undetected 33 10 2 CodeWarrior Installation Fails WinDriver Error 34 DEMO9S08QE8 User Manual 1 1 INTRODUCTION 1 1 Overview The DEMO9S08QE8 is a low cost development system designed for demonstrating evaluating and debugging the Freescale MC9S08QE8 microcontroller P amp E s Embedded Multilink circuitry on the DEMO9S08QE8 board allows the processor on the DEMO9S08QE8 to be debugged and programmed via USB from the PC In addition the demo board can be powered using the USB bus 1 2 Package Contents The DEMO9S08QE8 package includes the following items DEMOQE Base Board with a MC9S08QE8 Daughter Card installed 2 cell AAA battery package USB Cable Quick Start Guide Freescale Warranty Card 1 3 Supported Devices The DEMO9S08QE8 supports the MC9S08QE8CLC device 1 4 Recommended Materials On
3. 10 4 1 Overview 10 4 2 Debug Mode 10 4 3 Run Mode 11 4 4 External BDM Mode 11 5 DEMOQE TOOLKIT PC APPLICATIONS 11 5 1 DEMOQE Logic Analyzer Application 11 5 2 DEMOQE Terminal Application 12 5 3 DEMOQE Unsecure Application 13 5 4 DEMOQE Accelerometer Demo Application 14 5 5 DEMOQE Serial Grapher Application 15 6 DEMONSTRATION MICROCONTROLLER APPLICATIONS 18 6 1 Quick Start Application 18 6 2 Serial Accelerometer Application 19 iii DEMO9S08QE8 User Manual 7 JUMPER SETTINGS
4. On board Logic Analyzer On board Virtual Serial Port Asymmetrically positioned 4 8x2 male connectors for interchangeable daughter cards P amp E s Embedded Multilink circuitry populated on the bottom RS 232 Serial Port w DB9 F Connector SCI signals connected to P amp E s Embedded Multilink through jumpers DEMO9S08QE8 User Manual 3 ON OFF Power Switch w LED indicator A 5VDC to 8VDC power supply input barrel connector Note The DEMOQE board power connector is incorrectly labelled as 5 12VDC The maximum voltage is 8VDC Power Input Selection Jumpers for selecting the input voltage source Power Input from Embedded Multilink to LDO regulator Power Input from DC Power Jack to LDO regulator Regulated VDD Output at 3 0V Regulated VDD Output at 2 1V Power Input from Battery Power Input from MCU_PORT connector RESET Push Button and LED indicator w Enable Optional External Crystal Circuitry Layout not populated User Features 3 axis Accelerometer w Enable 8 User LED s w Enable 4 User Push Buttons w Enable 1 Piezzo Buzzer w Enable IIC Pullups w Enable 10K Ohm POT w Enable Option Jumpers COM_EN for 1 8V to 4 25V RS232 Transceiver TXD_EN for SCI_TXD to Embedded Multilink RXD_EN for SCI_RXD to Embedded Multilink INPUT_EN for two input chan
5. Below is an overview of the features and intended use of the USB Multilink and Cyclone PRO 9 1 1 USB Multilink Key Features Direct user control of target s execution Programming and debugging capabilities Read write registers and memory values Compact and lightweight Communication via USB 2 0 Supported by P amp E software and Freescale s CodeWarrior 9 1 2 Cyclone PRO Key Features Advanced programming and debugging capabilities including DEMO9S08QE8 User Manual 31 PC Controlled and User Controlled Stand Alone Operation Interactive Programming via Host PC In Circuit Debugging Programming and Testing Compatible with Freescale s ColdFireV1 HCS08 RS08 and HC S 12 X microcontroller families Communication via USB Serial and Ethernet Ports Multiple image storage LCD screen menu interface Supported by P amp E software and Freescale s CodeWarrior 9 2 Working With P amp E s USB Multilink Figure 9 1 P amp E s USB Multilink USB ML 12 shown 9 2 1 Product Features amp Implementation P amp E s USB Multilink Interface USB ML 12 connects your target to your PC and allows the PC access to the Background Debug Mode BDM on Freescale s ColdFireV1 HCS08 RS08 and HC S 12 X microcontrollers It connects between a USB port on a Windows 2000 XP 2003 machine and a standard 6 pin debug connector on the target
6. INPUT_EN J11 The DEMO9S08QE8 has 4 switches that are connected to signals PTA2 PTA3 PTD2 and PTD3 respectively and are enabled or disabled by the 4 corresponding jumpers KEY_ENABLE J12 The DEMO9S08QE8 has one Reset switch and one Reset LED associated with it These are enabled or disabled by the two corresponding jumpers RESET_EN J18 24 DEMO9S08QE8 User Manual 7 4 1 J11 P amp E s Logic Analyzer Inputs IN0 IN1 The logic analyzer inputs are marked on one side of the J11 jumper The inputs allow P amp E s PC based logic analyzer application to display these signals in real time By installing both jumpers the logic analyzer pins IN0 and IN1 will be connected to PTC0 and PTC1 respectively By removing these jumpers IN0 and IN1 will be unconnected The user may connect these signals via wires to any other signals on the processor which they wish to view on the PC Figure 7 8 Jumper Settings for Input Signals to P amp E s Embedded Multilink P amp E INPUT_EN J11 7 4 2 J12 Light Touch Switch Enable Jumper KEY_ENABLE Enables the corresponding switch Each jumper may be individually installed or removed By default all jumpers are installed to enable all the switches Figure 7 9 Jumper Settings for Light Touch Switches KEY_ENABLE J12 Note PTD2 and PTD3 have no effect on QE8 devices 7 4 3 J18 Reset Switch Enable and Reset LED Display Enable Jumper DEMO9S08QE8 User Manual 25 RESET_EN
7. By using the USB Multilink Interface the user can take advantage of the background debug mode to halt normal processor execution and use a PC to control the processor The user can then directly control the target s execution read write registers and memory values debug code on the processor and program internal or external FLASH memory devices The USB Multilink enables you to debug program and test your code on your board 32 DEMO9S08QE8 User Manual 9 2 2 Software The USB Multilink Interface works with Codewarrior as well as P amp E s in circuit debugger and flash programmer to allow debug and flash programming of the target processor P amp E s USB Multilink Development Packages come with the USB Multilink Interface as well as flash programming software in circuit debugging software Windows IDE and register file editor 9 3 Working With P amp E s Cyclone PRO Figure 9 2 P amp E s Cyclone PRO 9 3 1 Product Features amp Implementation P amp E s Cyclone PRO is an extremely flexible tool designed for debugging testing and in circuit flash programming of Freescale s ColdFireV1 HC08 HCS08 RS08 and HC S 12 X microcontrollers The Cyclone PRO connects your target to the PC via USB Ethernet or Serial Port and enables you to debug your code program and test it on your board After development is complete the Cyclone PRO can be used as a production tool on your manufacturing floor For production the Cy
8. DEMO9S08QE8 and are ready to build your own target you will need a hardware tool to allow you to develop using your own board P amp E s USB Multilink and P amp E s Cyclone PRO offer two effective solutions depending on your needs Both work with Freescale s 30 DEMO9S08QE8 User Manual CodeWarrior as well as P amp E software and both provide a seamless transition to working with your own hardware The USB Multilink is a development tool that is functionally comparable to the Embedded Multilink circuitry on the DEMO9S08QE8 It will enable you to debug your code and program it onto your target The Cyclone PRO is a more versatile and robust development tool with advanced features and production capabilities More information is available below to assist you in choosing the appropriate development tool for your needs 9 1 Hardware Solutions At A Glance The USB Multilink offers an affordable and compact solution for your development needs and allows debugging and programming to be accomplished simply and efficiently Those doing rapid development will find the USB Multilink easy to use and fully capable of fast paced debugging and programming The Cyclone PRO is a more complete solution designed for both development and production The Cyclone PRO featues automated power switching multiple communications interfaces including USB Ethernet and Serial stand alone programming functionality and many other advanced capabilities
9. Enables the Reset Switch and the Reset LED Display Each jumper may be individually installed or removed This is the default setting Figure 7 10 Reset Switch and Reset LED enable Jumper J18 7 5 3 Axis Accelerometer Jumper Settings The DEMO9S08QE8 integrates a 3 axis accelerometer Its enable or disable sensitivity levels and output signal connections are all jumper settable Jumpers J13 J14 J15 and J16 are associated with the accelerometer 7 5 1 J13 Accelerometer g Select1 Jumper G SEL1 Selects g Select1 to be logic low This is the default setting Selects g Select1 to be logic high A user may control PTD0 in firmware to set g Select1 TABLE 1 Accelerometer G Select Pin Descriptions G SEL2 G SEL1 g Range Sensitivity 0 0 1 5g 800 mV g 0 1 2g 600 mV g 1 0 4g 300 mV g 1 1 6g 200 mV g 26 DEMO9S08QE8 User Manual Figure 7 11 Accelerometer g Select1 Jumper settings J13 7 5 2 J14 Accelerometer g Select2 Jumper G SEL2 Selects g Select2 to be logic low This is the default setting Selects g Select2 to be logic high A user may control PTD0 in firmware to set g Select2 Figure 7 12 Accelerometer g Select2 Jumper settings J14 7 5 3 J15 Accelerometer Sleep Mode Select Jumper SLEEP J15 Enables the 3 axis accelerometer This is the default setting Puts the 3 axis accelerometer into sleep mode The user may control PTC4 in firmware to enable or disable the accelerometer In t
10. four waveforms An example graph is shown here Figure 5 6 Serial Grapher Graphing Component 5 5 2 Data Format The data format is broken into two sections depending upon whether the incoming data is in byte format or word format 5 5 2 1 Byte Formatted Data There are two commands which may be accepted Both commands must end in the special characters 0D and 0A which are CR carriage return and LF line feed The accepted commands are WnnZnnYnnXnn The nn values are 00 FF and correspond in order to the data displayed on the following graph lines W Z Y X AnnBnnCnnDnn The nn values are 00 FF and correspond in order to the data displayed on the 18 DEMO9S08QE8 User Manual following bar graphs lines A B C D 5 5 2 2 Word Formatted Data There are three commands which may be accepted All commands must end in the special characters 0D and 0A which are CR carriage return and LF line feed The accepted commands are nnnn nnnn nnnn nnnn The nnnn values are 0000 FFFF and correspond in order to the data displayed on both the graph and bar graphs as follows X A Y B Z C W D nnnn nnnn nnnn nnnn The nnnn values are 0000 FFFF and correspond in order to the data displayed the graphing component as follows X Y Z W nnnn nnnn nnnn nnnn The nnnn values are 0000 FFFF and correspond in order to the data displayed on the bar graph component as follows A B C D 6 DEMONSTRATION MICROCONTRO
11. 08QE8 User Manual 13 Figure 5 2 DEMOQE Terminal Application The terminal window may be set for full duplex or half duplex In full duplex mode only received characters are displayed in the terminal window In half duplex mode both transmitted and received characters are displayed This PC based application is included on the CD ROM that accompanys the DEMOQE and may also be found at http www pemicro com fixedlinks demoQEtoolkit html 5 3 DEMOQE Unsecure Application This application allows secure HCS08 microcontrollers to be unsecured The Unsecure application will erase a secure device to make it unsecure This application works with the DEMOQE board as well as other user hardware connected to the PC via the USB Multilink or Cyclone PRO hardware interfaces 14 DEMO9S08QE8 User Manual Figure 5 3 DEMOQE Unsecure Application This PC based application is included on the CD ROM that accompanys the DEMOQE and may also be found at http www pemicro com fixedlinks demoQEtoolkit html 5 4 DEMOQE Accelerometer Demo Application This PC based application will graph serial data output from the microcontroller based serial accelerometer application documented in Section 6 2 Serial Accelerometer Application The graphed data includes the magnitude of the X Y and Z accelerometer signals as well as the current processor loading For this application to work properly the microcontroller based serial accelerometer applicatio
12. 8QE8 through the Embedded Multilink circuitry Either the CodeWarrior Development Studio or P amp E s HCS08 software tools will work with the DEMO9S08QE8 Please refer to DEMO9S08QE8 User Manual 11 Section 8 DEMO9S08QE8 CODE DEVELOPMENT SOFTWARE for more information 4 3 Run Mode The DEMO9S08QE8 s rich component list empowers it to perform a variety of tasks Once an application is developed debugged and programmed properly into the QE8 internal flash memory it can run with or without connecting to a host 4 4 External BDM Mode The DEMO9S08QE8 has an optional BDM header for debugging and programming the on board QE8 device using an external BDM hardware tool such as P amp E s USB Multilink or Cyclone PRO Please refer to Section 9 TRANSITIONING TO YOUR OWN TARGET for more information A user can take advantage of this mode to develop a target specific QE8 system and compare it with the DEMO9S08QE8 when necessary 5 DEMOQE TOOLKIT PC APPLICATIONS P amp E provides several Windows PC based applications which work with the DEMO9S08QE8 board These applications are collectively referred to as the DEMOQE Toolkit The following applications are included in the toolkit 5 1 DEMOQE Logic Analyzer Application The DEMOQE board has a built in two channel logic analyzer This analyzer allows the IN0 and IN1 signals to be captured by the PC and displayed for the user The IN0 and IN1 signals may be connected to any of the MCU
13. DEMOQE Resources CD DEMO9S08QE8 Embedded Multilink hardware interface driver DEMO9S08QE8 User Manual this document DEMO9S08QE8 Quick Start Guide DEMO9S08QE8 Quick Start Application Source Code 2 DEMO9S08QE8 User Manual DEMO9S08QE8 Base Board and Daughter Cards Schematics DEMO9S08QE8 Component Breakdown List DEMOQE Toolkit Applications Links to P amp E Evaluation Software Links to Freescale documentation P amp E Discussion Forums and DEMO9S08QE8 FAQs 1 5 Handling Precautions Take care to handle the package contents including the DEMOQE base board and MC9S08QE8 daughter card in a manner such as to prevent electrostatic discharge 2 HARDWARE FEATURES The DEMO9S08QE8 is a demonstration and development system for Freescale s MC9S08QE8 microcontroller Application development is quick and easy using P amp E s Embedded Multilink circuitry and the included software tools and examples An optional BDM port is provided to allow use of an external BDM interface such as P amp E s Cyclone PRO automated programmer or USB Multilink The USB Multilink is functionally comparable to the DEMO9S08QE8 s Embedded Multilink circuitry Note The DEMO board s onboard Embedded Multilink circuitry is intended to function with the onbaord processor and any daughter cards that may be included It cannot be used to communicate with other devices 2 1 DEMOQE Base Board Features
14. LLER APPLICATIONS The following microcontroller applications are designed to run on the QE8 processors 6 1 Quick Start Application The function of the Quick Start microcontroller application is to play a different tone and illuminate a different LED for each of the buttons which may be pressed on the DEMO9S08QE8 board The potentiometer controls the intensity of two LEDs on the DEMO9S08QE8 board via PWM signals This application comes pre programmed into the memory of the QE8 processor The source code for this Quick Start Application is included on the CD ROM included with the DEMOQE and may also be found at http www pemicro com fixedlinks demoQEtoolkit html DEMO9S08QE8 User Manual 19 6 2 Serial Accelerometer Application This microcontroller application samples the state of the on board three axis accelerometer using on chip A D converter channels This data is converted into ASCII characters and sent out using the serial pins of the QE8 processor These serial pins may be connected to either serial port hardware or to P amp E s virtual serial port which is part of the Embedded Multilink design This connection is controlled by jumpers J6 and J7 P amp E has two PC based DEMOQE Toolkit applications which allow the serial port data generated by this application to be graphed These are documented in Section 5 4 DEMOQE Accelerometer Demo Application and Section 5 5 DEMOQE Serial Grapher Application The source code
15. PTB0 RXD signal to the Embedded Multilink SCI circuitry This is the default setting Figure 7 4 SCI RXD Signal Selection Jumper RXD_EN J6 7 2 2 J7 SCI TXD Signal Selection Jumper TXD_EN J7 Connects the microcontroller PTB1 TXD signal to the RS232 transceiver Connects the microcontroller PTB1 TXD signal to the Embedded Multilink SCI circuitry This is the default setting Figure 7 5 SCI TXD Signal Selection Jumper TXD_EN J7 7 2 3 J8 SCI Transceiver Enable COM_EN J8 Enables the SCI Transceiver The user may control PTC5 in firmware to enable or disable the transceiver DEMO9S08QE8 User Manual 23 Disables the SCI Transceiver This is the default setting Figure 7 6 SCI Transceiver Enable Disable Selection COM_EN J8 7 3 LED Display Port The DEMOQE Base Board has 8 LEDs connected to signals PTC0 PTC1 PTC2 PTC3 PTC4 PTC5 PTE6 and PTE7 They can be enabled or disabled by installing or removing the corresponding jumper J9 in the LED_ENABLE header 7 3 1 J9 LED Display Enable Port LED_ENABLE Enables all LED outputs This is the default setting Figure 7 7 LED Display Enable Header LED_ENABLE J9 Note PTE6 and PTE7 have no effect on QE8 devices 7 4 Input and Reset Switches The DEMO9S08QE8 has an option to connect two signals PTC0 and PTC1 to the Embedded Multilink for signal processing The two signals are connected or disconnected to IN0 or IN1 correspondingly via jumpers P amp E
16. Purchase Agreement P amp E Microcomputer Systems Inc reserves the right to make changes without further notice to any products herein to improve reliability function or design P amp E Microcomputer Systems Inc does not assume any liability arising out of the application or use of any product or circuit described herein This software and accompanying documentation are protected by United States Copyright law and also by International Treaty provisions Any use of this software in violation of copyright law or the terms of this agreement will be prosecuted All the software described in this document is copyrighted by P amp E Microcomputer Systems Inc Copyright notices have been included in the software P amp E Microcomputer Systems authorizes you to make archival copies of the software and documentation for the sole purpose of back up and protecting your investment from loss Under no circumstances may you copy this software or documentation for the purpose of distribution to others Under no conditions may you remove the copyright notices from this software or documentation This software may be used by one person on as many computers as that person uses provided that the software is never used on two computers at the same time P amp E expects that group programming projects making use of this software will purchase a copy of the software and documentation for each user in the group Contact P amp E for volume discounts and site licensin
17. T_EN The regulator can output either a 2 1VDC or 3VDC voltage for the DEMO9S08QE8 The VOLT_EN jumper J4 selects the voltage Figure 7 2 shows the regulator output selection details Select regulator output to be 2 1V Select regulator output to be 3V Figure 7 2 Regulator Voltage Output Selection VOLT_EN J4 7 1 3 J5 VDD Source Selection Jumper VDD_SELECT Select the regulator to supply microcontroller VDD This is the default setting DEMO9S08QE8 User Manual 21 Select the battery pack to supply microcontroller VDD Select the MCU_PORT to supply microcontroller VDD This setting also allows power to be supplied to the target connected to the MCU_PORT By default this jumper is installed Figure 7 3 VDD_SELECT Option Header J5 7 2 RS232 Communications The DEMO9S08QE8 integrates an RS232 transceiver for the microcontroller SCI signals The transceiver operates from 1 8V to 4 25V and it can be enabled or disabled via jumper settings or through firmware control The DEMO9S08QE8 also integrates the SCI signal into the Embedded Multilink circuitry A user can communicate with the microcontroller SCI module via either the on board DB9 connector or the Embedded Multilink circuitry There are three jumpers associated with SCI communication 7 2 1 J6 SCI RXD Signal Selection Jumper RXD_EN Connects the microcontroller PTB0 RXD signal to the RS232 transceiver 22 DEMO9S08QE8 User Manual Connects the microcontroller
18. an be accepted and displayed either as incoming byte values 00 FF or word values 0000 FFFF The data format indicates whether the data is byte or word data The graphical components automatically size their range depending upon the incoming data 5 5 1 Visual Components The Bar Graph has four separate bars A B C and D On each bar a percentage value is displayed which indicates the current value relative to the full range A byte value of 7F max is FF would show up as approximately 50 as would a word value of 7FFF max is FFFF As can be seen in the data formatting section all four bars must be written at the same time The bars are shown here Figure 5 5 Serial Grapher Bar Graph The graphing component shows four waveforms X Y Z and W The magnitude axis either has a range of 00 FF if byte values are incoming on the serial port or 0000 FFFF if word values are incoming Each new set of values which comes through the serial port is added to the far right side of the graph and the rest of the data values move to the left The vertical axis displays the incoming data as the magnitude of each waveform and the horizontal axis displays the number of samples The graph has a limited size DEMO9S08QE8 User Manual 17 so older samples will eventually fall off the left part of the graph As can be seen in Section 5 5 2 Data Format each incoming data command affecting the graphing component must have new data for all
19. ch allows the user to connect to the DEMO9S08QE8 hardware If this dialog indicates that the DEMO9S08QE8 hardware is not connected to the PC the first step is to make sure that the DEMO9S08QE8 hardware is connected to the PC via a USB 2 0 high speed cable If it is connected unplug and then plug in the USB cable on the DEMO9S08QE8 board and click refresh in the connection assistant If the hardware still does not show up try the following remedies A Re Enable the USB driver If you connected the DEMO9S08QE8 interface prior to installing P amp E s Embedded Multilink drivers Windows will not have been able to find the appropriate driver and may have disabled the device The DEMO9S08QE8 board shows up in Window s device manager as a P amp E Multilink since it contains P amp E s Embedded Multilink circuitry If you unplug and then plug in the device Windows will automatically disable it even if you have installed the drivers To force windows to try to load the driver again perform the following steps while the DEMO9S08QE8 interface is connected to the computer 1 Open the Control Panel Start Button gt Settings gt Control Panel 34 DEMO9S08QE8 User Manual 2 Double Click the System Icon 3 Select the Hardware tab 4 Click the Device Manager Button 5 The P amp E Multilink device will be shown with an exclamation mark next to it Double click this device 6 Click the Reinstall Driver button and
20. clone PRO may be operated interactively via Windows based programming applications as well as under batch or dll commands from a PC Once loaded with data by a PC it can be disconnected and operated manually in a stand alone mode via the LCD menu and control buttons The Cyclone PRO has over 3Mbytes of non volatile memory which allows the onboard storage of multiple programming images When connected to a PC for programming or loading it can communicate via the ethernet USB or serial interfaces DEMO9S08QE8 User Manual 33 9 3 2 Software The Cyclone PRO comes with intuitive configuration software and interactive programming software as well as easy to use automated control software The Cyclone PRO also functions as a full featured debug interface and is supported by Freescale s CodeWarrior as well as development software from P amp E P amp E s Cyclone PRO is also available bundled with additional software as part of various Development Packages In addition to the Cyclone PRO these Development Packages include in circuit debugging software flash programming software a Windows IDE and register file editor 10 TROUBLESHOOTING 10 1 DEMO9S08QE8 Is Undetected Q The connection assistant indicates that my DEMO9S08QE8 is undetected even though I have connected the hardware to my USB port What should I do A The connection assistant which displays in either Codewarrior or P amp E s development software is a dialog whi
21. ection By default it is connected to PTA0 Figure 7 17 Potentiometer Output Selection Jumpers POT_EN J21 7 9 Optional External Crystal Circuitry Jumper Enable The DEMO9S08QE8 provides external crystal circuitry without components populated A user may elect to populate the components and may use jumper J17 CLOCK_EN to enable the external crystal circuitry 7 9 1 J17 External Crystal Circuitry Enable Jumpers CLOCK_EN Enables or disables the external crystal circuitry Both positions must be installed to enable use of crystal circuitry Figure 7 18 External Crystal Circuitry Enable Jumper CLOCK_EN J17 7 10 Optional Jumpers For Various VDD And VSS The DEMO9S08QE8 provides 5 jumpers J22 through J25 for different VDD and VSS connections on the bottom of the board By default they are not populated and are shorted correspondingly with zero ohm resistors in parallel except J24 which is populated A user may take off the zero ohm resistor and install a corresponding jumper Note JR2 Jumper 23 and JR5 Jumper 26 have no efffect on QE8 devices DEMO9S08QE8 User Manual 29 8 DEMO9S08QE8 CODE DEVELOPMENT SOFTWARE The DEMO9S08QE8 includes P amp E s Embedded Multilink circuitry so no external hardware BDM tool is needed to debug and program the DEMO9S08QE8 A user only needs to connect the DEMO9S08QE8 to their PC to start developing code for it The DEMO9S08QE8 package comes with a special edition of Freescale
22. ection 1 4 Recommended Materials On DEMOQE Resources CD 3 4 Quick Startup Only a few steps are required to get the DEMO9S08QE8 up and running Step 1 If you do not have CodeWarrior Development Studio version 6 0 installed on your computer please install it using the accompanying CD ROM Additional information regarding CodeWarrior can be found at www freescale com Step 2 Remove the DEMO9S08QE8 demonstration board from its anti static pouch The green MC9S08QE8 daughter card should be plugged into the header on the base board Step 3 Connect the USB cable from your computer to the DEMO9S08QE8 demonstration board Depending on your operating system you may need to follow steps to install the USB driver from the DEMOQE Resources CD ROM Once the USB cable is connected properly the green USB LED on the DEMO9S08QE8 should illuminate Step 4 Turn on the DEMO9S08QE8 power switch K6 The red Power LED should illuminate Step 5 Press the buttons labelled PTA2 and PTA3 When each button is pressed a different tone will be emitted and the light intensity of the PTC0 LED will change The LEDs labelled PTC1 and PTC2 for PTA2 or PTC3 and PTC4 for PTA3 should illuminate In addition the light intensity of the LED labeled PTC1 should vary as the potentiometer is rotated Step 6 Optionally you may run the DEMOQE Logic Analyzer Application available in the DEMOQE toolkit on the CD This PC based application graphs the IN0 a
23. follow the dialog instructions to have Windows automatically install the driver B Re Install the USB driver If the Multilink device does not show up in the device manager use the driver installation utility located in the DEMOQE Resouces CD ROM After driver installation unplug the DEMO9S08QE8 from the PC and reboot the PC When the reboot has completed connect the interface to the PC with the USB 2 0 cable Run the software again to see if the interface is now detected If you have an error attempting to install the drivers please view the installation troubleshooting FAQ on P amp E s website at http www pemicro com faqs faq_view cfm id 89 C Test for installation of the USB driver files To test the driver installation use the driver test utility in the DEMOQE Resources CD ROM to make sure all files were properly installed This may give some indication of what the problem is D Using a USB Hub The DEMO9S08QE8 is a high power USB device If a USB Hub is used it must be a self powered hub i e with its own power supply If the Hub is not self powered the DEMO9S08QE8 will not work In general USB ports located directly on the PC are high power self powered ports 10 2 CodeWarrior Installation Fails WinDriver Error Q When I try to install the Codewarrior or P amp E software installation fails with this message There are currently 2 open applications using WinDriver Please close all applications and pre
24. for this microcontroller based Serial Accelerometer Application is included on the CD ROM included with the DEMOQE and also may be found at http www pemicro com fixedlinks demoQEtoolkit html 7 JUMPER SETTINGS 7 1 System Power The QE8 processor may obtain its power from either the on board regulator a 2 cell battery pack or through MCU_PORT J1 The on board regulator obtains its input from either the Embedded Multilink circuitry or a 2 5mm barrel connector The on board regulator can regulate the output to either 2 1V or 3V The DEMO9S08QE8 is fully functional at both voltages Power input and voltage selection are achieved by using 3 option headers 7 1 1 J3 Regulator Input Selection Jumper Jumper 3 determines whether the DEMO9S08QE8 s on board regulator obtains its power from the DC power jack or from the Embedded Multilink circuitry The regulator input selection is mutually exclusive It prevents power input contention from damaging the board and the host Figure 7 1 shows the regulator input selection details 20 DEMO9S08QE8 User Manual Select regulator input from DC power jack A 5 8VDC center positive power supply must be used The DEMOQE board power connector is incorrectly labelled as 5 12VDC The maximum voltage is 8VDC Select regulator input from the Embedded Multilink circuitry which derives its power from the USB bus Figure 7 1 PWR Selection Header J3 7 1 2 J4 Regulator Output Selection Jumper VOL
25. from the drop down menu Reboot your PC after the installation finishes If you are unable to disable the WinDriver system driver in the above fashion you can delete the file c windows system32 windrvr6 sys and then reboot your machine You should then re run the installer and complete the procedure Reboot your machine after the installation has finished 36 DEMO9S08QE8 User Manual
26. g agreements P amp E Microcomputer Systems does not assume any liability for the use of this software beyond the original purchase price of the software In no event will P amp E Microcomputer Systems be liable for additional damages including any lost profits lost savings or other incidental or consequential damages arising out of the use or inability to use these programs even if P amp E Microcomputer Systems has been advised of the possibility of such damage By using this software you accept the terms of this agreement 2009 P amp E Microcomputer Systems Inc MS DOS and Windows are registered trademarks of Microsoft Corporation Freescale and ColdFire are registered trademarks of Freescale Inc IBM and PowerPC are registered trademarks of IBM corporation P amp E Microcomputer Systems Inc 98 Galen St Watertown MA 02472 617 923 0053 http www pemicro com Manual version 1 01 DEMO9S08QE8 User Manual ii 1 INTRODUCTION 1 1 1 Overview 1 1 2 Package Contents 1 1 3 Supported Devices 1 1 4 Recommended Materials O
27. his configuration the user needs to pay close attention to LED PTC4 and RSTO configuration Figure 7 13 Accelerometer Sleep Mode Jumper settings J15 DEMO9S08QE8 User Manual 27 7 5 4 J16 Accelerometer 3 axis Signals Connection Jumper ACC_EN The accelerometer output signals are jumper settable to PTA7 PTA6 PTC7 and PTA1 PTA6 and PTC7 share the same Y axis signal By default the Y axis signal is connected to PTA6 Figure 7 14 Accelerometer Signal Output ACC_EN J16 7 6 Buzzer The DEMO9S08QE8 integrates a Piezo Transducer whose resonant frequency is 4 0KHz Jumper J19 connects to PTB5 to control this buzzer 7 6 1 J19 Buzzer enable jumper BUZ_EN Enables Buzzer to be controlled by PTB5 This is the default setting Figure 7 15 Accelerometer Signal Output ACC_EN J19 7 7 IIC Pull up The DEMO9S08QE8 provides external pull up resistors for SCL and SDA lines enabled by installing the corresponding jumpers on J20 By default both jumpers are installed 7 7 1 J20 IIC Pullup Enable Jumpers IIC_EN Enables IIC external pullup This is the default setting Figure 7 16 IIC External Pullup Enable IIC_EN J20 28 DEMO9S08QE8 User Manual 7 8 Analog Input Potentiometer The DEMO9S08QE8 provides an easy access 10Kohm potentiometer whose output may be connected to PTC6 and or PTA0 selectable by J21 POT_EN 7 8 1 J21 Potentiometer Output Selection Jumpers POT_EN Selects the potentiometer output conn
28. ion the following dialog box will appear DEMO9S08QE8 User Manual 9 Figure 3 3 Found New Hardware Wizard Dialog 2 of 4 Click the Finish button to exit the current Found New Hardware Wizard 7 Depending on the operating system you may see the Found New Hardware Wizard dialog again helping you to install software for PEMicro USB Serial Port i1 On Windows XP SP2 the following dialog will appear Figure 3 4 Found New Hardware Wizard Dialog 3 of 4 Select the Install the software automatically Recommended option and click the Next button 8 Windows will install the driver files to your system At the end of the installation the following dialog box will appear 10 DEMO9S08QE8 User Manual Figure 3 5 Found New Hardware Wizard Dialog 4 of 4 Click the Finish button to exit the Found New Hardware Wizard If the DEMO9S08QE8 hardware interface driver is now properly installed on your system the green USB LED on the DEMOQE Base Board should be illuminated In addition if you turn on the system power of the DEMO9S08QE8 you will see the red Power LED illuminate 4 OPERATING MODES 4 1 Overview The DEMO9S08QE8 s Embedded Multilink circuitry featured hardware components and optional external BDM header make it a versatile development tool Below are some of the featured operating modes of the DEMO9S08QE8 4 2 Debug Mode A host communicates with the DEMO9S0
29. n DEMOQE Resources CD 1 1 5 Handling Precautions 2 2 HARDWARE FEATURES 2 2 1 DEMOQE Base Board Features 2 2 2 On Board Logic Analyzer 4 2 3 On Board Virtual Serial Port 4 2 4 DEMOQE Daughter Card Features 5 3 SYSTEM SETUP 5 3 1 Overview 5 3 2 Operating System Requirements 5 3 3 Software Setup 5 3 4 Quick Startup 6 3 5 Hardware Setup 7 4 OPERATING MODES
30. n must be programmed into the microcontroller which is plugged into the DEMOQE board DEMO9S08QE8 User Manual 15 Figure 5 4 Accelererometer Demo Application The data that is graphed may come from either the PC serial port or the virtual serial port on the DEMOQE board The serial port of the microcontroller on the DEMOQE board is routed to either serial port hardware or the virtual COM port based upon the setting of jumpers J6 and J7 This PC based application is included on the CD ROM that accompanys the DEMOQE and may also be found at http www pemicro com fixedlinks demoQEtoolkit html 5 5 DEMOQE Serial Grapher Application This PC based application is a more generalized version of the accelerometer demo application It may be used with the microcontroller based serial accelerometer application or customer microcontroller code which transmits data in the correct format The serial graphing utility allows incoming data on the PC serial port or one of P amp E s virtual serial ports to be automatically graphed in time or displayed upon a series of bar graphs The virtual serial port exists on several of P amp E s embedded USB multilink designs including the DEMOQE board This PC based application is included on the CD ROM that accompanys the DEMOQE and may also be found at http www pemicro com fixedlinks demoQEtoolkit html 16 DEMO9S08QE8 User Manual All data to be displayed must be in hexadecimal format The data c
31. nd IN1 signals on the DEMOQE board If both J11 jumpers are installed IN0 shows PTC0 and IN1 DEMO9S08QE8 User Manual 7 shows PTC1 Push button PTA2 and turn the potentiometer to change these signals This application may also be found at http www pemicro com fixedlinks demoQEtoolkit html Figure 3 1 DEMOQE Logic Analyzer Application 3 5 Hardware Setup 3 5 1 First Time Connection The DEMO9S08QE8 may be connected to a PC through a USB port Connection steps are listed below in typical order 1 Install the required software as described in the previous section 2 Make sure the jumpers for USB_PWR 3V for VOLT_EN and REG_VDD for VDD_SELECT are installed 3 Plug the USB cable A M connector into a free USB port of the PC 4 Plug the USB cable B M connector into the USB connector on the DEMOQE Base Board 5 The operating system will recognize P amp E s Embedded Multilink cir cuitry and P amp E s USB to Serial circuitry Depending on the operating system you may see the Found New Hardware Wizard dialog help ing you to install software for PEMicro USB Multilink i0 On Win dows XP SP2 the following dialog will appear 8 DEMO9S08QE8 User Manual Figure 3 2 Found New Hardware Wizard Dialog 1 of 4 Select the Install the software automatically Recommended option and click the Next button 6 Windows will install the driver files to your system At the end of the installat
32. nels to Embedded Multilink Specifications Board Size 3 5 x 4 0 Power Input 4 DEMO9S08QE8 User Manual USB Cable 5VDC 500mA max DC Power Jack 2 5 5 5mm barrel connector 5VDC to 8VDC Center Positive Note The DEMOQE board power connector is incorrectly labelled as 5 12VDC The maximum voltage is 8VDC Two AAA Battery Cells Figure 2 1 DEMOQE Top Component Placement 2 2 On Board Logic Analyzer The DEMOQE board has a built in 2 channel logic analyzer which may be used to display captured data in real time on a host PC The logic analyzer channels IN0 IN1 are connected to the PTC0 and PTC1 signals on the DEMOQE board by default via the J11 jumpers The channels may be connected to any of the processor pins by wire jumpers not included The DEMOQE Logic Analyzer Utility included in the DEMOQE Toolkit on the accompanying CD ROM displays the logic analyzer signals on a PC 2 3 On Board Virtual Serial Port The DEMOQE board has a built in virtual serial port which may be connected to the QE processor s SCI RXD TXD This allows certain PC applications to DEMO9S08QE8 User Manual 5 be able to connect in a serial fashion to the microcontroller without the actual use of serial port hardware The DEMOQE Terminal Window Utility included in the DEMOQE Toolkit on the accompanying CD ROM is a generic serial port utility which works with the DEMOQE virtual serial port or actual serial p
33. ort hardware 2 4 DEMOQE Daughter Card Features Four bottom mounted asymmetrically positioned 8x2 female connectors to mate with the DEMOQE Base Board A top mounted MC9S08QE8CLC chip 3 SYSTEM SETUP 3 1 Overview P amp E s Embedded Multilink driver is required to operate the DEMO9S08QE8 using a PC The Embedded Multilink driver should be installed with the CodeWarrior Development Studio software or from the DEMOQE Resources in the CD ROM before the PC is connected to the DEMO9S08QE8 3 2 Operating System Requirements The following are the resources required to run the CodeWarrior Development Studio and the DEMO9S08QE8 A PC compatible system running Windows 2000 Windows XP or Windows Vista 128MB of available system RAM and 1GB of available hard disk space A CD ROM drive for software installation A USB port 3 3 Software Setup 3 3 1 Installing CodeWarrior Development Studio To install the CodeWarrior Development Studio insert the CodeWarrior CD 6 DEMO9S08QE8 User Manual into your computer s CD ROM drive A start up window will automatically appear Select CodeWarrior Installation and follow the on screen instructions 3 3 2 Installing P amp E Resources Use the DEMOQE Resources CD ROM to access and install P amp E resources for the DEMO9S08QE8 These materials are not required for operation The support materials contained on the DEMOQE Resources CD ROM are listed in S
34. s CodeWarrior studio In addition P amp E s evaluation software for HCS08 is available online at www pemicro com A user may use either CodeWarrior or P amp E software tools to develop code for the DEMO9S08QE8 8 1 Using CodeWarrior With The DEMO9S08QE8 The CodeWarrior studio supports Freescale s HCS08 devices It offers C C and assembly level support and provides debugging capabilities based on P amp E s debug and programming technologies A programming or debug session with the project based CodeWarrior IDE may be launched by double clicking on the project name the format is projectname mcp from your file storage Its tutorials FAQs and quick start guides are easy to follow and will allow you use pre built templates to begin creating a new project in a short time 8 2 Using P amp E Software With The DEMO9S08QE8 P amp E offers software tools for Freescale s HCS08 devices that can be used to develop code for the DEMO9S08QE8 board P amp E offers an integrated development environment which combines a command line assembler in circuit debugger and flash memory programmer The assembler includes features such as a full string replacement macro conditional assembly include files and more The debugger supports both assembly and C source level debugging The programmer can program reprogram both internal and external flash devices in circuit 9 TRANSITIONING TO YOUR OWN TARGET Once you have finished working with the
35. signals which the user would like to view By default they are connected to the PTC0 and PTC1 pins of the MCU by jumper J11 At the time of this release the logic analyzer runs at a capture rate of 10khz 12 DEMO9S08QE8 User Manual Figure 5 1 Logic Analyzer Application This PC based application is used to display the logic analyzer data on the PC The logic analyzer data is displayed in real time and each waveform may be paused zoomed and printed If the microcontroller based Quick Start Application is programmed into the MCU the IN0 channel will show the PWM output on pin PTC0 whose duty cycle is controlled by the potentiometer W1 The IN1 channel shows the PWM output on channel PTC1 which drivers the buzzer This PC based application is included on the CD ROM that accompanys the DEMOQE and may also be found at http www pemicro com fixedlinks demoQEtoolkit html 5 2 DEMOQE Terminal Application This PC based application acts as a standard serial port terminal application on the PC It works with standard serial ports as well as the virtual serial port on the DEMOQE board The application includes settings to adjust the COM port number baud rate parity and number of data bits There is a button to take a file on the PC and transmit it out of the serial port There are also delays which are automatically inserted in the transmission output to prevent overruns It is recommended that these defaults not be changed DEMO9S
36. ss Retry To reload WinDriver press Cancel and reboot How do I solve this A Some software applications on your PC are connected to the Windriver system driver which manages P amp E s USB connections This system driver needs to be disabled for the installation to continue Directions to disable DEMO9S08QE8 User Manual 35 Windriver are as follows In Windows Explorer right click on My Computer and select Properties from the drop down menu 1 Select the Hardware tab 2 Click on the Device Manager button 3 Select the System Devices in the Device Manager window 4 Expand the tree index for System Devices 5 At the bottom of the System Devices list you should see the Win Driver item 6 Right click on WinDriver and select Disable from the drop down menu 7 Click Yes OK when the confirmation dialog appears WinDriver is now disabled and you should be able to complete the installation After the installation finishes you should re enable the WinDriver system driver using the following steps In Windows Explorer right click on My Computer and select Properties from the drop down menu 1 Select the Hardware tab 2 Click on the Device Manager button 3 Select the System Devices in the Device Manager window 4 Expand the tree index for System Devices 5 At the bottom of the System Devices list you should see a WinDriver item 6 Right click on WinDriver and select Enable
Download Pdf Manuals
Related Search