2018 Users Guide 610..
Contents
1. Hart Scientific 2018 Thermometer Carousel Rev 610401 Limited Warranty amp Limitation of Liability Each product from Fluke s Hart Scientific Division Hart is warranted to be free from defects in mate rial and workmanship under normal use and service The warranty period is one year for the Carousel Holding Fixture The warranty period begins on the date of the shipment Parts product repairs and ser vices are warranted for 90 days The warranty extends only to the original buyer or end user customer of a Hart authorized reseller and does not apply to fuses disposable batteries or to any other product which in Hart s opinion has been misused altered neglected or damaged by accident or abnormal conditions of operation or handling Hart warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non defective media Hart does not warrant that software will be error free or operate without interruption Hart authorized resellers shall extend this warranty on new and unused products to end user customers only but have no authority to extend a greater or different warranty on behalf of Hart Warranty support is available if product is purchased through a Hart authorized sales outlet or Buyer has paid the applicable international price Hart reserves the right to invoice Buyer for importation costs of repairs replacement parts when pro2. Warning and Caution e WARNING identifies conditions and actions that may pose hazards to the user e CAUTION identifies conditions and actions that may damage the in strument being used WARNINGS To avoid personal injury follow these guidelines GENERAL Appropriate personal safety protection should be worn by the operator at all times while using the instrument and calibration bath 1 Before You Start Safety Information DO NOT use the instrument for any application other than calibration work The instrument was designed for use with a Hart Scientific Model 6055 bath for temperature calibration Any other use of the unit may cause unknown haz ards to the user DO NOT use the instrument in equipment other than a Hart Scientific Model 6055 calibration bath DO NOT use the instrument in environments other than those listed in the user s guide DO NOT overfill the bath Allow for thermal expansion As some fluids heat up they expand which can cause overflowing of extremely hot fluid which may be harmful to the operator See calibration bath manual for specific instructions Typically the instrument is installed in the calibration bath and never removed If the instrument is to be removed from the bath DO NOT wipe instrument down with a towel or other flammable medium If the bath set point is high the salt can ignite causing severe injury to the technician or extreme danger of fire or exp
3. directly into the bath fluid if required The wheel shaped handle above the carousel allows liquid in glass thermome ters to be rotated into position for proper viewing of each instrument s meniscus by the user Symbols Used Table 1 lists the International Electrical Symbols Some or all of these symbols may be used on the instrument or in this manual Table 1 International Electrical Symbols Symbol Description Z AC Alternating Current AS AC DC Battery CE Complies with European Union Directives A MA DC Double Insulated Electric Shock 1 r Fuse 2018 Thermometer Carousel User s Guide 1 3 1 3 1 Symbol Description PE Ground Hot Surface Burn Hazard A Read the User s Manual Important Information Off On Canadian Standards Association c US OVERVOLTAGE Installation CATEGORY II Pollution Degree 2 per IEC1010 1 re fers to the level of Impulse Withstand Voltage protection provided Equipment of OVERVOLTAGE CATEGORY II is energy consuming equipment to be supplied from the fixed installation Examples include household office and laboratory appliances C TIC Australian EMC Mark m The European Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC mark Safety Information Use this instrument only as specified in this manual Otherwise the protection provided by the instrument may be impaired The following definitions apply to the terms
4. REACH OF WARRANTY OR BASED ON CONTRACT TORT RELIANCE OR ANY OTHER THEORY Since some countries or states do not allow limitation of the term of an implied warranty or exclusion or limitation of incidental or consequential damages the limitations and exclusions of this warranty may not apply to every buyer If any provision of this Warranty is held invalid or unenforceable by a court of com petent jurisdiction such holding will not affect the validity or enforceability of any other provision Fluke Corporation Hart Scientific Division 799 E Utah Valley Drive American Fork UT 84003 9775 USA Phone 1 801 763 1600 Telefax 1 801 763 1010 E mail support hartscientific com www hartscientific com Subject to change without notice e Copyright 2006 Printed in USA 1 Before You Start Introduction 1 1 1 2 Before You Start Introduction The 2018 carousel is designed for use with Model 6055 calibration bath It mounts into the bath access opening and is secured into place using the two shoulder screws supplied with the carousel The 2018 is designed for use with either liquid in glass thermometers or metal sheathed probes The carousel is constructed of stainless steel and can be safely used with all bath fluids over the entire range of the 6055 It can hold up to twelve thermometers or probes with out exposing them to the bath fluid One open well is located in the center of the device for placing a reference probe
5. bes used with it are sensitive instru ments that can be easily damaged Always handle these devices with care Do not allow them to be dropped struck stressed or overheated When removing probes from the bath DO NOT wipe probes down with a pa per towel If the bath set point is high the salt can cause the paper towel to ig nite in your hand Provide a safe surface and situation for the probes to cool prior to cleaning the salt from the probes DO ensure the fluid is cleaned from the probes prior to immersing the probe in the next bath Clean your probe be tween each bath to avoid contamination between bath fluids Under filling the bath in which this instrument is used may reduce the bath per formance and may possibly damage the bath When calibrating PRTs always follow correct calibration procedure and cali brate from high temperatures to low temperatures with the appropriate triple point of water checks Never immerse a wet or cold PRT into a bath filled with hot fluid Severe damage to the PRT may result as well as personal injury to the calibration technician 1 Before You Start Authorized Service Centers 1 4 Authorized Service Centers Please contact one of the following authorized Service Centers to coordinate service on your Hart product Fluke Corporation Hart Scientific Division 799 E Utah Valley Drive American Fork UT 84003 9775 USA Phone 1 801 763 1600 Telefax 1 801 763 1010 E mail support harts
6. cientific com Fluke Nederland B V Customer Support Services Science Park Eindhoven 5108 5692 EC Son NETHERLANDS Phone 31 402 675300 Telefax 3 1 402 675321 E mail ServiceDesk fluke nl Fluke Int l Corporation Service Center Instrimpex Room 2301 Sciteck Tower 22 Jianguomenwai Dajie Chao Yang District Beijing 100004 PRC CHINA Phone 86 10 6 5 12 3436 Telefax 86 10 6 5 12 3437 E mail xingye han fluke com cn Fluke South East Asia Pte Ltd Fluke ASEAN Regional Office Service Center 2018 Thermometer Carousel User s Guide 60 Alexandra Terrace 03 16 The Comtech Lobby D 118502 SINGAPORE Phone 65 6799 5588 Telefax 65 6799 5588 E mail antng singa fluke com When contacting these Service Centers for support please have the following information available e Model Number e Serial Number e Voltage e Complete description of the problem 2 Specifications Specifications Probe Outer Diameter Max 9 0mm 0 354 in Probe Immersion Max 427mm 16 8 in Wetted Parts 304 Stainless Steel 3 Carousel Installation 3 Carousel Installation WARNING Read all warnings and cautions is this guide and in the 6055 Calibration Bath User s Guide before installing the carousel into the bath 1 The salt must be in a liquid state before installing the carousel into the bath The volume used by the carousel is approximately 459 cubic centimeters 28 cubic inches w
7. duct purchased in one country is submitted for repair in another country Hart s warranty obligation is limited at Hart s option to refund of the purchase price free of charge re pair or replacement of a defective product which is returned to a Hart authorized service center within the warranty period To obtain warranty service contact your nearest Hart authorized service center or send the product with a description of the difficulty postage and insurance prepaid FOB Destination to the nearest Hart au thorized service center Hart assumes no risk for damage in transit Following warranty repair the prod uct will be returned to Buyer transportation prepaid FOB Destination If Hart determines that the failure was caused by misuse alteration accident or abnormal condition or operation or handling Hart will provide an estimate or repair costs and obtain authorization before commencing the work Following repair the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the repair and return transportation charges FOB Shipping Point THIS WARRANTY IS BUYER S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IM PLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE HART SHALL NOT BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSE QUENTIAL DAMAGES OR LOSSES INCLUDING LOSS OF DATA WHETHER ARISING FROM B
8. e bath that will react with the bath fluid Ensure that probes are 2018 Thermometer Carousel User s Guide 1 3 2 DRY and free of contaminants Read the MSDS Material Safety Data Sheet for the bath fluid used Precautions must be taken to prevent personal injury or damage to objects Probes may be extremely hot when removed from the bath Cautiously handle probes to prevent personal injury Carefully place probes on a heat resistant sur face or rack until they are at room temperature BATH FLUIDS Salt used may produce noxious or toxic fumes under certain circumstances Consult the fluid manufacturer s MSDS Material Safety Data Sheet Proper ventilation and safety precautions must be observed A CAUTIONS To avoid possible damage to the instrument follow these guidelines DO NOT overfill the bath in which this instrument is used Overflowing liquid may damage the electrical system Be sure to allow for thermal expansion of the fluid as the bath temperature increases See the calibration bath user s guide for specific instructions This instrument is a precision instrument Although it has been designed for optimum durability and trouble free operation it must be handled with care Position the bath before the tank is filled with fluid Most probes have handle temperature limits Be sure that the probe handle tem perature limit is not exceeded in the air above the instrument The instrument and any thermometer pro
9. hich means the fluid level in the bath has to be re duced by approximately 1 27 centimeters 0 5 inches If applicable remove the access cover not the lid from the bath The ac cess cover is the part that is placed directly over the Constant Level Flow Test Well see Figure 4 System Diagram in the 6055 Calibration Bath User s Guide WARNING Before inserting the carousel in the bath insure that it is clean dry and free of all contaminants Personal injury or death can oc cur from reaction of contaminants and bath salt Refer to the salt MSDS for more information 4 Carefully install the carousel into the bath The carousel can only be in stalled in the bath one direction The small end needs to be placed into the Flow Test Well Once the carousel is inserted in the bath install and tighten the shoulder screws 2 supplied with the carousel to secure it in place If the shoulder screws are not installed and tightened the carousel could move around due to the upward flow within the Flow Test Well
10. losion Provide a safe surface and situation for the probes to cool prior to cleaning the salt from the instrument Once the instrument and salt on the in strument have cooled to ambient 25 C the salt can be safely cleaned from the instrument Read BURN HAZARDS before re installing the instrument into a bath Follow all safety guidelines listed in the user s manual Calibration Equipment should only be used by Trained Personnel DO NOT operate high temperature baths 500 C near flammable materials Extreme temperatures could ignite the flammable material Overhead clearance is required Do not place the instrument under a cabinet or other structure Always leave enough clearance to allow for safe and easy inser tion and removal of probes The instrument is intended for indoor use only BURN HAZARD The bath in which this instrument is used may generate extreme temperatures High temperatures may be present in this equipment Fires and severe burns may result if personnel fail to observe safety precautions Before installing this unit in a bath ensure the bath DOES NOT contain any water and has been completely dried prior to filling with fluid Any trapped wa ter can cause a steam explosion resulting in personal injury If the bath has been filled with water ensure the inside of the drain tube is dry prior to filling the bath with salt When immersing any object in the bath ensure that you are not introducing anything into th
Download Pdf Manuals
Related Search