APWR106 User Manual - RTD Embedded Technologies, Inc.
Contents
1. AFW version only C 12 VDC 1 17 Amp 12 VDC 1 17 Amp 14 Watts Max Nl FS AN FS PC 104 BUS APWRI06 11 RTD Embedded Technologies Inc Chapter 5 RETURN POLICY AND WARRANTY Return Policy APWR106 If the utilityModule requires repair you may return it to us by following the procedure listed below Caution Failure to follow this return procedure will almost always delay repair Please help us expedite your repair by following this procedure 1 Read the limited warranty which follows 2 Contact the factory and request a Returned Merchandise Authorization RMA number 3 On a sheet of paper write the name phone number and fax number of a technically competent person who can answer questions about the problem 4 On the paper write a detailed description of the problem with the product Answer the following questions e Did the product ever work in your application What other devices were connected to the product was power supplied to the product e What features did and did not work What was being done when the product failed What were environmental conditions when the product failed 5 Indicate the method we should use to ship the product back to you e We will return warranty repairs by UPS Ground at our expense Warranty repairs may be returned by a faster service at your expense e Non warranty repairs will be returned by UPS Ground or the method you select2. Chapter 3 CONNECTING THE UTILITYMODULE The following sections describe connectors of the utilityModule Finding Pin 1 of Connectors Pin of connectors is indicated by a square solder pad visible on the bottom of the PC board Component Locations The figure below shows locations of major components including connectors Connector Dimension CNI XT PC 104 bus 64 pin CN2 32 pin TBI 2 terminal TBS 2 terminal TB3 2 terminal TB2 2 terminal TB4 2 terminal APWR106 6 RTD Embedded Technologies Inc User s Manual PC 104 Bus Connectors CN1 and CN2 Connectors CN1 and CN2 provide PC 104 bus connections CN1 carries XT bus signals and CN2 carries additional signals for the AT bus The signals on CN1 and CN2 conform to the IEEE P966 standard for PC 104 bus The APWR106 series power only supplies the 5V OV Gnd 12V APWR106 and 12V pins All other pins are not connected The following tables list the connector pinouts PC 104 XT Bus Connector CN1 Pin Row A 1 IOCHCHK 2 SD7 3 SD6 4 SD5 5 SD4 6 SD3 7 SD2 8 SD1 9 SDO 10 IOCHRDY 11 AEN 12 19 13 SA18 14 SA17 15 SA16 16 SA15 17 SA14 18 SA13 19 SA12 20 SA11 21 SA10 22 SA9 23 SA8 24 SA7 25 SA6 26 SAS 27 SA4 28 SA3 29 SA2 30 SAl 31 SAO 32 OV 7 Row B OV RESETDRV 5V IRQ9 5V DRQ2 12V ENDXFR 12V KEYING PIN SMEMW SMEMR IOW IOR DACK3 DRQ3 DACKI DRQI REFRESH SYSCLK IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 DAC
3. and will be billed to you 6 Clearly specify the address to which we should return the product when repaired 7 Enclose the paper with the product being returned 8 Carefully package the product to be returned using anti static packaging We will not be responsible for products damaged in transit for repair 7 Write the RMA number on the outside of the package 8 Ship the package to RTD Embedded Technologies Inc 103 Innovation Blvd State College PA 16804 0906 USA 12 RTD Embedded Technologies Inc User s Manual Limited Warranty APWR106 RTD EMBEDDED TECHNOLOGIES INC WARRANTS THE HARDWARE AND SOFTWARE PRODUCTS IT MANUFACTURES AND PRODUCES TO BE FREE FROM DEFECTS IN MATERIALS AND WORKMANSHIP FOR ONE YEAR FOLLOWING THE DATE OF SHIPMENT FROM RTD EMBEDDED TECHNOLOGIES THIS WARRANTY IS LIMITED TO THE ORIGINAL PURCHASER OF PRODUCT AND IS NOT TRANSFERABLE DURING THE ONE YEAR WARRANTY PERIOD RTD EMBEDDED TECHNOLOGIES WILL REPAIR OR REPLACE AT ITS OPTION ANY DEFECTIVE PRODUCTS OR PARTS AT NO ADDITIONAL CHARGE PROVIDED THAT THE PRODUCT IS RETURNED SHIPPING PREPAID TO RTD EMBEDDED TECHNOLOGIES ALL REPLACED PARTS AND PRODUCTS BECOME THE PROPERTY OF RTD EMBEDDED TECHNOLOGIES BEFORE RETURNING ANY PRODUCT FOR REPAIR CUSTOMERS ARE REQUIRED TO CONTACT THE FACTORY FOR AN RMA NUMBER THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY PRODUCTS WHICH HAVE BEEN DAMAGED AS A RESULT OF ACCIDENT MISUSE ABUSE SUCH AS USE OF INC
4. LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE 13 RTD Embedded Technologies Inc
5. APWR106HR Filtered Avionics Power Supply Module User s Manual RTD Embedded Technologies Inc Accessing the Analog World BDM 61002007 1 RevA APWR106 Filtered Avionics Power Supply Module User s Manual RTD Embedded Technologies Inc 103 Innovation Blvd State College PA 16804 0906 USA Phone 814 234 8087 FAX 814 234 5218 E Mail sales rtd com techsupport rtd com Website www rtd com Revision History 08 August 2008 Rev A Initial release Published by RTD Embedded Technologies Inc 103 Innovation Blvd State College PA 16804 0906 Copyright 2008 by RTD Embedded Technologies Inc All rights reserved Printed in U S A The RTD Logo is a registered trademark of RTD Embedded Technologies cpuModule and utilityModule are trademarks of RTD Embedded Technologies PhoenixPICO and PheonixPICO BIOS are trademarks of Phoenix Technologies Ltd PS 2 PC XT PC AT and IBM are trademarks of International Business Machines Inc MS DOS Windows Windows 95 Windows 98 and Windows NT are trademarks of Microsoft Corp PC 104 is a registered trademark of PC 104 Consortium All other trademarks appearing in this document are the property of their respective owners User s Manual Table of Contents CHAPTER 1 INTRODUCTION cccccssssseeeccensseeeccensseseccensseseccenssesenceassesescenssesesees 2 APWR106 Filtered Avionics Power 2 Feat
6. K2 TC BALE 5V OSC OV OV RTD Embedded Technologies Inc Note PC 104 AT Bus Connector CN2 Pin Row C 0 OV 1 SBHE 2 LA23 3 LA22 4 LA21 5 LA20 6 LA19 7 LA18 8 LA17 9 MEMR 10 MEMW 11 SD8 12 SD9 13 SD10 14 SD11 15 SD12 16 SD13 17 SD14 18 SD15 19 KEYING PIN Row D OV 16 IOCS16 IRQ10 IRQ11 IRQ12 IRQ15 IRQ14 DACKO DRQO DACK5 DRQ5 DACK6 DRQ6 DACK7 DRQ7 45V MASTER OV OV Two locations on the bus have mechanical keying pins to help prevent misconnection of the PC 104 bus These keying pins are a part of the PC 104 standard and we strongly recommend you leave them in place If you have other modules without keying pins we suggest you modify them to include keying 16 50 VDC Input TB1 Terminal block TB1 is the input power connection for the APWR106 The input range is 16 50 VDC Fully loaded this input can require 10 amps therefore 18 gauge wire is recommended APWR106 Pin Signal Vin 16 50 VDC input Vin RTD Embedded Technologies Inc User s Manual Filtered Vout Output TB5 Terminal block TB5 is the output of the filter This is 4 Amps on APWRI106HR 50W Pin Signal 1 Vout Filtered Vout 2 Ground Ground 5 VDC Output TB2 The 5 VDC output is supplied to the 5 V pins on the PC 104 bus and to terminal block TB2 This supply is capable of providing 6 amps total that is shared by the PC 104 bus devices and any device
7. ORRECT INPUT VOLTAGES IMPROPER OR INSUFFICIENT VENTILATION FAILURE TO FOLLOW THE OPERATING INSTRUCTIONS THAT ARE PROVIDED BY RTD EMBEDDED TECHNOLOGIES ACTS OF GOD OR OTHER CONTINGENCIES BEYOND THE CONTROL OF RTD EMBEDDED TECHNOLOGIES OR AS A RESULT OF SERVICE OR MODIFICATION BY ANYONE OTHER THAN RTD EMBEDDED TECHNOLOGIES EXCEPT AS EXPRESSLY SET FORTH ABOVE NO OTHER WARRANTIES ARE EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND RTD EMBEDDED TECHNOLOGIES EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED HEREIN ALL IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES FOR MECHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS WARRANTY IN THE EVENT THE PRODUCT IS NOT FREE FROM DEFECTS AS WARRANTED ABOVE THE PURCHASER S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE UNDER NO CIRCUMSTANCES WILL RTD EMBEDDED TECHNOLOGIES BE LIABLE TO THE PURCHASER OR ANY USER FOR ANY DAMAGES INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXPENSES LOST PROFITS LOST SAVINGS OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS AND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC
8. STALLING THE UTILITYMODULE Since the utilityModule uses a PC 104 stackthrough bus the only hardware installation you will do is placing the module to the PC 104 stack To do this you will connect the PC 104 bus connector with the matching connector of another module Recommended Procedure APWR106 We recommend you follow the procedure below to ensure that stacking of the modules does not damage connectors or electronics e Turn off power to the PC 104 system or stack e Select and install standoffs to properly position the utilityModule on the PC 104 stack e Touch a grounded metal part of the stack to discharge any buildup of static electricity e Remove the utilityModule from its anti static bag e Check that keying pins in the PC 104 bus connector are properly positioned e Check the stacking order make sure an XT bus card will not be placed between two AT bus cards or it will interrupt the AT bus signals e Hold the utilityModule by its edges and orient it so the bus connector pins line up with the matching connector on the stack e Gently and evenly press the utilityModule onto the PC 104 stack CAUTION Do not force the module onto the stack Wiggling the module or applying too much force may damage it If the module does not readily press into place remove it check for bent pins or out of place keying pins and try again 4 RTD Embedded Technologies Inc User s Manual APWR106 5 RTD Embedded Technologies Inc
9. ltered Avionics Power Module The APWR106 Filtered Avionics Power Module was designed to power a PC 104 system from the typical unregulated noisy 28 VDC aircraft power Features The following are major features of the APWR106 powerModule Input e 16 50 VDC Outputs e 5 VDC 6 Amps e Amps filtered input voltage 40dB attenuation at S00KHz e 12 VDC at 1 17 Amps each total max combined power 20 Watts HighRel e High input transient voltage of 80V for 1 sec per MIL STD 704A e Designed to meet MIL STD 461C CEO3 and MIL STD 461D EMC requirements Protects against conducted susceptibility specified in MIL STD 461C 01 and CS02 e 40 to 85 degrees C operation e Hermetically sealed modules e MIL PRF 38534 Element Evaluated Components APWR106 2 RTD Embedded Technologies Inc User s Manual Connectors Connectors provided are CNI and CN2 PC 104 bus e TBI 16 50 VDC input e TB2 Filtered input voltage e TB3 5 VDC output e TB4 12 VDC output e TB5 12 VDC output General Specifications Dimensions 3 8 x 4 75 x 0 6 97 x 120 x 16 mm including connectors e Weight mass e 50W version 0 42 Ib 0 19 Kg e 4 Jayer PCB combined through hole and surface mount e Operating conditions e Temperature e 40 to 85 degrees C operational e Relative humidity 0 95 non condensing e Storage temperature 65 to 150 degrees C APWRI06 3 RTD Embedded Technologies Inc Chapter 2 IN
10. s connected to TB2 Pin Signal 1 5 VDC Regulated 5 VDC Output 2 Ground 12 VDC Output TB3 The 12 VDC output of the APWRIOGHR 50W is supplied to the 12 V pins on the PC 104 bus and to terminal block TB3 This supply is capable of providing 1 17 amps total that is shared by the PC 104 bus devices and any devices connected to TB3 Note that the total power drawn from the 12 VDC and the 12 VDC supplies together cannot exceed 20 watts Pin Signal 1 12 VDC Regulated 12 VDC Output 2 Ground Ground APWR106 9 RTD Embedded Technologies Inc 12 VDC Output TB4 APWR106 The 12 VDC output of the APWRIOGHR 50W is supplied to the 12 V pins on the PC 104 bus and to terminal block TB4 This supply is capable of providing 1 17 amps total that is shared by the PC 104 bus devices and any devices connected to TB4 Note that the total power drawn from the 12 VDC and the 12 VDC supplies together cannot exceed 20 watts Pin Signal in out 1 12 VDC Regulated 12 VDC Output Out 2 Ground Out 10 RTD Embedded Technologies Inc User s Manual Chapter 4 USING THE UTILITYMODULE Using the utilityModule is straightforward Connect the input to TB1 using good wiring practices keeping the wires as short and as heavy as possible The 5 VDC is provided Below is the block diagram TB 16 50 VDC Input High Rel EMI Filter and Input Attenuator TB5 Filtered Yin 5 VDC 6 Amp TB2 30 Watts Max 5 VDC
11. ures REESE M 2 CODBeCLOISz seiten teilte Esto uter etie Eo A one fede Ho e a Meere 3 General Specifications roo eed Sere A A ode des Tere sedi linie 3 CHAPTER 2 INSTALLING THE een 4 Recommended Procedure m 4 CHAPTER CONNECTING THE UTILITYMODULE nrnna 6 Finding Pin 1 o Connectors a aee tee ito edu ken a eau ate it teret 6 PC 104 Bus Connectors CN1 and CNOQ eee e eerte esee ee sete eese 7 16 50 VDC Input TBI es 8 Filtered aO UAM R o 9 DO AN ym 9 12 VDC AAA O 9 12 VDC Output TB er S as osoa s E a Seoses 10 CHAPTER 4 USING THE 11 CHAPTER 5 RETURN POLICY AND WARRANTY 12 AA NON 12 Limited A M 13 APWR106 1 RTD Embedded Technologies Inc Chapter 1 INTRODUCTION This manual gives information on APWR106 Filtered Avionics Power Module This power supply provides filtered input power 5 VDC and optionally 12 VDC to power the PC 104 bus and external devices APWR106 Fi
Download Pdf Manuals
Related Search