User Manual - Video Management Solutions
Contents
1. USER MANUAL VIDEO h soray Windows Based Network Video Recorders NW 8 Inspect the packaging carton Make sure the Windows Based NVR is properly delivered Remove all items from the box and make sure the box contains the following items Windows Based NVR Setup Guide Power Adaptor Power Cord F Q C ae 0o00 000000000 E Ga Q00000000000 90000 v Front Panel Local Display Models 10 9 8 7 65432 1 Network Video Recorder USB AUDIO OUT 11 Non Local Display Models 9 8 7 6543 2 1 Network Video Recbrder l LAN WAN Blue The NVR system is on The power key will not respond while the system is running Power Key Green They NVR system is shutdown but PoE switch is still alive Press the power key to startup the system OFF The power cord is disconnected Reset Switch Insert a pin to force restart the system The PoE LED will start to blink when the output power is reaching to the FOEREN limit 1 Blink The HDD CF Card is running HDD LED 2 OFF No storage device is found we h WANLED 4 Orange Network speed is 10 100 Mbps Uplink LED LED Uplink LED 2 Green Network speed is 1000 Mbps With different models of NVR the number of Camera LEDs is also Camera LEDS different The following is description of the lightened LEDs 1 Orange The power is supplied by the camera itself i 2 Green The power is supplied by the PoE switch at the rear panel The USB 2 0 po2. Click lt OK gt to save the setting System Restore It is recommended to create a restore point when users first start up the system Once unexpected system errors occur users can restore the system to the restore point The following describes how to create a restore point and restore the system e Click on lt Start gt menu and right click on lt Computer gt Click on lt Properties gt gt lt System Protection gt lt System Properties gt will be displayed e Click on lt Create gt button below to setup a restore point Users will be asked to name the restore point After users input a name click on lt Create gt button A message window will indicate a restore point is being created Users will be notified that the setting is completed and can click lt Close gt to exit e Click on lt System Restore gt under System Restore section lt System Restore gt will pop out Click on lt Next gt button and a list of restore points will be displayed Select a preferred restore point and click on lt Next gt button Click on lt Finish gt button to start restoring the system e Awarning window will be displayed Select lt Yes gt to start restoring the system This process may take a while so please wait patiently The system will reboot by itself An information window will pop out indicating the system restore has finished For more details please visit http windows microsoft com en US windows 7 products features sys
3. Required Devices and Power on the NVR Before power on the NVR connect the following devices first e USB Mouse amp USB Keyboard e IP Cameras via PoE Ports e Monitor VGA or HDMI e Internet WAN Lastly connect the power cord to the NVR and login the Windows system Note that the power source should be between AC 110V AC 240V Startup the NVR on Standby When the system is shutdown but the power is still on Green LED users can press the power key to restart the NVR A NOTE Due to security concern the Power key will not respond while the Windows is running A NOTE If USB hub and KVM switch are required for application insert these devices AFTER THE SYSTEM SUCCESSFULLY BOOTS UP Otherwise the unknown devices may cause boot up failure Windows System Setting Internet Information Server IIS lf users have any software that needs to use port 80 users have to change the setting of IIS and VSS connection port Refer to the following instructions e Switch ON the IIS via lt Control Panel gt gt lt System and Security gt gt lt Administrative Tools gt gt lt Services gt gt lt World Wide Web Publishing Service gt gt lt Startup type gt gt lt Enable gt e At VSS click on the lt Setting gt button of VSS and select lt Client Setting gt tab Change the port number at lt Connect Port gt at top right Note that the port number must be changed to a different number that is not often used such as 20000
4. added IP cameras e Click on lt OK gt at the bottom to save the setting Default IP Addresses for IP Cameras and VSS The connected IP cameras will each be automatically assigned a unique IP address for connection from other devices in the same local area network The default IP address for CH1 is 192 168 50 11 for CH2 is 192 168 50 12 and so on Note that the network setting of the IP cameras need to be set to DHCP or the NVR will not be able to assign the default IP addresses to them In the mean time VSS also has a default IP for LAN connection which is 192 168 50 27 for 16CH models and 192 168 50 35 for 24CH models This IP address can be found when users check lt Control Panel gt gt lt Network and Sharing Center gt gt lt Local Area Connection gt gt lt Details gt AN NOTE The IP address of the VSS for WAN connection can be found via lt Control Panel gt gt lt Network and Sharing Center gt gt lt Local Area Network 3 gt gt lt Details gt O NVR Remote and Mobile Apps Support Users can also connect to VSS via NVR Remote the remote monitoring software and or Apps such as NetGuard NetGuardHD iOS or DroidGuard DroidGuardHD Android on portable handy devices After VSS is connected users can view both Live Playback videos and can search the video database Refer to the User s Manual of VSS and the App s Help info for detailed description NSW Silverwater Unit 4 52 Holker Street Silver
5. ll sites at all times VMS will automatically add VSS as the start group and videos from the connected IP cameras will be automatically retrieved and displayed Auto HDD Management The Auto HDD Management function of VSS helps to automatically add all connected HDDs except the C drive as the storage folders of the recorded videos If the system has detected any portable HDD at any time it will be added to the folder list as well Click on the lt Setting gt button and select the lt File Path gt tab to see the folder list Check the box in front of lt Hard Disk Auto Detection gt to enable or disable this function AN NOTE WD RED and WD Se series HDDs are recommended for the Windows Based NVR Add More IP Camera Sites If any PoE port is not connected to IP cameras users can add IP camera connections via internet Follow the steps below e Click on the lt Setting gt button Right click on lt New Group gt in the site tree and select lt Add a site gt to add another connected IP camera Input the IP address of the IP camera or find it via lt Device Search gt Input the username and password to complete adding the IP camera site e Alternatively users can also right click on lt New Group gt in the site tree and select lt Add sites gt to add multiple IP camera sites at once Press and hold the Ctrl key to select IP cameras Then input username and password for each site e Enable auto streaming configuration for the
6. ndows is updated users MUST turn off Windows Updates by following the same steps in Turn Off Windows Updates section Local Display NVR vs Non Local Display NVR For NVR with CPU supporting local display Video Storage Server VSS and Video Management Solutions VMS are pre installed Startup the NVR system and VSS amp VMS will automatically startup as well For NVR requiring Live video display at a different PC only Video Storage Server VSS will be pre installed Startup the NVR system and VSS will automatically startup as well The following sections with VMS contents do not apply to the non local display NVR Users can install and operate VMS at a different PC according to the User s Manual of VMS A NOTE If users turn on the Windows Firewall please add VSS and VMS to the exception list of the Windows Firewall to avoid them from being block by the firewall A NOTE If users already have any familiar backend software other than VSS please refer to the software s manual for installation and operation Auto Connection of VSS and VMS Refer to the following for details of auto connection and auto setting of VSS and CMS e VSS and VMS will be automatically login with the username admin and the password 1234 e P cameras connected via the PoE ports are plug and play They will be automatically added to the start group of VSS e The lt Schedule Record gt setting will be unavailable VSS is preset to record a
7. rts allow users to connect external USB devices such as USB 2 0 Ports 2 USB mouse a USB keyboard a USB storage device etc Local display models contain three USB 2 0 ports and non local display models include two USB 2 0 ports The USB 3 0 ports support all 3 0 2 0 and 1 0 devices Users can connect USB 3 0 Ports external USB devices such as a USB mouse a USB keyboard a USB storage device etc e SATA Local Display Users can connect an e SATA storage device via this port Models Only Audio Out Local Display An audio out connector is provided to output sounds Models Only Rear Panel Local Display Models a VGA Monitor The VGA output connector is offered for connection to a VGA monitor 2 e SATA Users can connect an e SATA storage device via this port 3 HDMI Monitor A HDMI connector is provided for connection to a HDMI monitor UbLink SEP Users can connect an SFP module that expands the NVR s private p network connection by fiber ports This port has absolute priority over the Ru 45 port for uplink and they will not function simultaneously This is for connection to a router or switch within the NVR s private UpLink RJ 45 network to share the network connection The RJ 45 port will not function when the SFP hhh scat is connected no matter before or after WAN RJ 45 This This port is for network connection tothe internet 0000 is for network connection to the internet The PoE s
8. tem restore Turn Off Windows Updates To prevent the NVR from stopping recording due to automatic system restart after Windows updates it is recommended to turn off Windows Updates Follow the steps to disable this function e Go to lt Control Panel gt gt lt System and Security gt gt lt Windows Update gt gt lt Change Settings gt e Select lt Never check for updates not recommended gt under Important updates section e Uncheck the selections under Recommended updates section and Who can install updates section Then click lt OK gt to save the settings and exit e After the above setting is done click on lt Start gt menu right click on lt Computer gt and then select lt Manage gt Select lt Service gt under lt Services and Applications gt on the left e Double click on lt Windows Update gt Select lt Disabled gt next to Startup type and click lt Stop gt under Service Status section Click lt OK gt to apply the setting and exit Conditionally Turn On Windows Updates lf users wish to update Windows system follow the steps below to enable this function e Go to lt Control Panel gt gt lt System and Security gt gt lt Windows Update gt gt lt Change Settings gt e Select lt Install updates automatically recommended gt under Important updates section e Click lt OK gt to save the settings and exit Automatic Windows Updates will begin AN NOTE After Wi
9. water NSW 2128 E vmssales opticalsolutions com au P 61 2 9395 1400 F 61 2 9647 0014 NSW Sydney City Unit 10 10 Bradford Street Alexandria NSW 2015 E vmssales opticalsolutions com au P 61 2 9304 4555 F 61 2 9700 8055 OPTICAL SOLUTIONS AUSTRALIA VIC Unit 3 1 Rocklea Drive Port Melbourne VIC 3207 P 61 3 9646 4166 F 61 3 9646 4155 QLD Unit 2 40 Borthwick Ave Murarrie QLD 4172 P 61 7 3399 5280 F 61 7 3399 9805 3 Years Advanced Replacement Warranty E vmssales opticalsolutions com au E vmssales opticalsolutions com au ACT 22 Isa Street Fyshwick ACT 2609 E vmssales opticalsolutions com au P 61 2 6162 4600 F 61 2 6162 4605 WA 28a Teddington Rd Burswood WA 6100 E vmssales opticalsolutions com au P 61 8 9361 7000 F 61 8 9361 7011 Conditions Apply Ph 1300 130 423
10. witch provides connection to IP cameras With different models of NVR the number of PoE switch is also different a lower sae Connect the power cord and the power adaptor shipped with the NVR Use of other power supply may cause overloading Non Local Display Models EN i UPLINK e SATA HDMI AUDIO OUT hn ne 2 VGA Monitor The VGA output connector is offered for connection toa VGA monitor a HDMI Monitor AHDMI connector is provided for connection to a HOMI monitor Ca eSATA Users can connect an e SATA storage device viathis por s Rs292 This port provides connection to a RS282 device Users can connect a SFP module that expands the NVR s private UpLink SFP network connection by fiber ports This port has absolute priority over the RJ 45 port for uplink and they will not function simultaneously This is for connection to a router or switch within the NVR s private 7 UpLink RJ 45 network to share the network connection The RJ 45 port will not function when the SFP EE on or is connected no matter before or after 8 WAN RJ 45 This This port is for network connection to the internet 000 is for network connection to the internet The PoE switch provides connection to IP cameras With different models of NVR the number of PoE switch is also different 10 Power Jack Connect the power cord and the power adaptor shipped with the NVR Use of other power supply may cause overloading Connect
Download Pdf Manuals
Related Search