iPR-9 proximity reader
Contents
1. 0 140 150 105 200 105 200 Wiring Reader has 8 wire colored cable intended for connection to access control panel Table 2 The wires assignment Multiwire signal cable with 0 22 mm wires cross sectional is recommended to use for connection of the reader and control panel Using this cable the maximum length of 50 meters can be obtained Type of interfaces The proximity reader is intended to be applied in different access control systems using RS232 Wiegand 26 Wiegand 37 Wiegand 42 or TouchMemory interface Table 2 Mounting fs W2w3 w4 Wws __RS232 It is recommended to mount the reader on a wall closely to a door at Color Function appropriate height Data 0 Do not mount the reader on metal surface since it causes decreasing of Data 1 reading distance Red V If two readers are mounted at a distance less than 50sm reading distance GND of a card may be reduced appreciably In such a case connect yellow Red Led wires of the readers The readers will synchronize and work in turn Green Led e Synchronization allows mounting of two readers at a small distance to the Blue Beep extent of reading distance of a card In case that two readers are mounted Yellow at a distance less than reading distance of a card the card may be read by the reader behind the wall To mount the iPR 2 iPR 3 readers proceeds as follows Connect the reader to the control panel s cable Smart Innovations 1 Using the body reade2. User manual of iPR x proximity readers A Lie i IPR3 IPR6 IPR 7 IPR 8 iIPR 9 Function iPR x proximity readers is intended to be applied in different access control systems using RS232 Wiegand 26 Wiegand 37 or Wiegand 42 interface Reader iPR 9 have with built in keypad Types of identificators Smart Innovations manufactures readers operating with amplitude modulation ASK proximity cards and tags Design The reader is placed in miniature hermetic plastic or vandal proof of polished stainless steel IPR 3 case Thanks to the small overall dimensions the reader is distinguished for its advanced reliability Specifications Warm up time 10 seconds after power start Case Material ABS plastic 1 5 mm thick stainless steel iPR 3 Dimensions IPR 2_ __ iPR 3_ __ iPR 6___ iPR 7__ iPR 8_ PRO 150x45x22 110x80x15 95x50x16 95x50x16 105 200 105 200 Weight IPR 2 __JiPR 3_ PRG _ iPR 7 __ iPR 8_ _ iPR 9 Ambient Conditions Temperature 35 65 C Humidity 100 without condensate Power supply Voltage 9 16 V of direct current Current up to 50 mA Maximal currentup to 80 mA Voltage ripple up to 500 mV Distance of reading Typical reading distance show in table 1 and depends on tag type used with it This parameter is valid for power supply voltage range from 9 to 16 VDC and ripple up to 150 MVp p Table 1 Reader type _ iPR 2__ iPR 3 iPR 6___ iPR 7__ iPR 8_ _ iPR 9 150 160 35 40 105 20
3. ground In this mode reader does not read cards thus current consumption decreases to 25mA Do not apply voltage to hold outlet Data transfer and Annunciation The reader is provided with two color LED and built in buzzer LED and buzzer function according to interface type programmed and annunciation mode Wiegand or TouchMemory Interface Engaging of LED and buzzer is possible automatically or by closing of corresponding wire to the black wire GND according to Table 2 Table 2 Annunciation mode X Buzzer Red LED Gren LED S Ponana amarg nn eee at reading at reading Beep on card read Switched OFF Blinks at reading Outside control Switched OFF Blinks at reading at reading at reading 06 Beep on card read Outside control Outside control Outside control Outside control Outside control Beep on card read Normally ON switched OFF Blinks at reading Availability to switch ON at reading Availability to Availability to switch from outside switch OFF from outside ON from outside Data transmissions from reader comply with the standard specified Protocol for TouchMemory interface from family 01 to satisfy the requirements DS1990 RS232 interface To control annunciation send three byte control packet to the reader Packets should be transmitted with 2 400 bits per second 8 bit data no parity 1 stop bit Packet format red blinks steady byte 2 green green buzzer buzzer steady blinks pulsatory uninter
4. ovations This warranty contains the entire warranty Smart Innovations neither assumes nor authorizes any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it any warranty or liability concerning this product In no event shall Smart Innovations be liable for any direct indirect or consequential damages Loss of anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure of this product Smart Innovations 3
5. r as a template mark and then drill two four openings 6mm in diameter and 35mm deep Secure the mounting plate on a wall using plastic nailing plugs and screws To mount the iPR 6 iPR 7 readers proceeds as follows Remove cover from reader Connect the reader to the control panel s cable Secure the mounting plate on a wall using plastic nailing plugs and screws Secure cover to the reader Ensure thet all locking tabs are securely To mount the iPR 8 iPR 9 readers proceeds as follows Remove the boot in the bottom part of the reader with loosing the screw Push mounting panel towards the screw and remove it from the reader Using the mounting panel as a template mark and then drill two openings 6mm in diameter and 35mm deep Pass the wire through central opening Secure the mounting plate on a wall using plastic nailing plugs and screws Connect the reader to the control panel s cable Put on the reader on the mounting plate push the case down against stop and secure the reader with the screw Put on the boot The Reader Operation Reading of identificator code The code reading is annunciated by built in buzzer and two color LED according to interface type and annunciation mode refer to Data transfer and Annunciation Repeated reading will be available after 0 8 sec if the identificator is moved away from the reader sensing area Hold Mode Reader is turned to the hold mode while yellow wire is closed to the
6. ruptedly Smart Innovations 2 1 corresponds to LED or buzzer switching on LED blinking and buzzer pulsatory control bits have the highest priority Annunciation does not change until next control packet is received Reader transmits data as follows oe po pao p e Card read 23h data C sum OD h data w e Destination Checksum exclusive OR of low nibbles of bytes from 1 to 10 high nibble of always must be 3h Example Card code 7E000460AA will be sent as 23h 37h 3Eh 30h 30h 30h 34h 36h 30h 3Ah 3Ah 3Bh ODh Limited Warranty Smart Innovations warrants that for a period of eighteen months from the date of purchase the product shall be free of defect in materials and workmanship under normal use and that in fulfillment of any breach of such warranty Smart Innovations shall at its option repair or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in parts and workmanship and not damages incurred in shipping or handing or damages due to causes beyond the control of Smart Innovations such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of the equipment The foregoing warranty shall apply only to the original buyer and is and shall be lieu of any and all other warranties whether expressed or implied and of all other obligations or liabilities on the part of Smart Inn
Download Pdf Manuals
Related Search