MultiSpot® HT3012
Contents
1. The pre programmed soft fade or hard switching patterns can be chosen by means of CH1 whilst CH2 is used as a level channel CH3 allows to set the fade time or pattern speed from slow value 50 to very fast value 255 If channel 4 reaches a DMX value of 50 or above a tact function will be added to the chases The tact speed can be adjusted from slow value 50 to 23 pulses per second value 255 Note Whether the unit works in static mix mode or pattern mode only depends on the value of channel 3 So make sure the value of channel 3 is lower than 50 to be in static mix mode Otherwise you will be in pattern mode In this mode the potentiometer 1 is disabled Display on off If you wish the display to be lit only when a change in operation is made the DIP switch 10 should be in the position off Now if any of the buttons is not pressed for more than approximately 25 seconds the display is switched off As soon as one of the buttons is pressed again the display switches on immediately Key lock Pressing the MODE button 5 for longer than 3 seconds locks all the buttons 5 7 and the potentiometer 1 The display shows LOC in alteration to the mode changing V3 00 08 2013 14 User Manual Multispot GI HT3012 WW MULTIFORM every 2 seconds Pressing the MODE button again for more than 3 seconds unlocks the button and potentiometer functions Please note If the display is in OFF mode it will take approximately 25 seconds2. C5 Pink C15 Leaf C6 Turquoise C16 Purple C7 Lime C17 Barbie C8 Orange C18 Breeze c9 Marine C19 White V3 00 08 2013 11 User Manual Multispot GI HT3012 WM MULTIFORM d3 Mode DMX 3 Channel RAW Mode Press the MODE button 5 until the display shows d3 indicating operation in d3 3 channel DMX mode Shortly after that the display shows the DMX starting address You can choose any DMX starting address by simply using the UP DOWN buttons 6 7 The chosen DMX address comes effective approximately 3 seconds later and will show up on the display 2 in alternation to the d This allows control of the unit by any external DMX signal sending on the chosen channel In this mode the potentiometer 1 is disabled The unit receives DMX values on a packet of three channels and mirrors the received data on the DMX output 13 If a DMX signal is present the DMX LED 3 will turn on The three channels control the unit as follows DMX channel Value Range Function CH1 000 255 Red Intensity CH2 000 255 Green Intensity CH3 000 255 Blue Intensity This setting is stored even if the device is switched off Note For master slave operation the slave units shall be set to d3 mode d4 Mode DMX 4 Channel Combined Master Strobe Mode Press the MODE button 5 until the display shows d4 indicating operation in d4 4 Channel DMX mode Shortly after that the display sh
3. 012 in environments with more than 35 degrees environmental temperature or more than 75 relative humidity Do not operate the Multispot GI HT3012 in any position inclined or reclined more than 45 degrees from being upright heatsink on top Do not operate the Multispot GI HT3012 in any closed environment smaller than 10cbm unless forced air convection is provided V3 00 08 2013 6 User Manual Multispot GI HT3012 WW MULTIFORM m Getting started secure mounting The Multispot GI HT3012 can be positioned for operation in various ways Floor standing operation Turn the bracket to the lower side of the unit and fold out the second inlaying bracket Place the unit in a secure position where it can neither be touched by anyone or could possibly become an objective for anyone to stumble Make sure to comply with cooling reguirements of the used power supply if any Hanging Rigging ceiling mounted operation calculating working load limits knowledge installation materials and periodic safety inspection of all installation material and the unit If you lack such gualifications do not attempt the installation yourself Improper installation can result in body injury Be sure to complete all rigging and installation procedures before applying power to the unit 1 Risk of injury Overhead mounting reguires extensive experience like Leave the inner and outer bracket folded The unit should be installed out of reach of people and o
4. MultiSpo HT3012 Exclusive USA Distributor e VV MULTIFORM e gt X RS APOLL DESIGN Introduction Since 1992 Apollo Design Technology Inc has been one of the world s leading innovators manufacturers and distributors of gobos color filters lights and related eguipment and accessories for the lighting industry We are continually engineering new products to help you create and execute the designs of your dreams for theaters bands advertising touring companies television motion pictures museums retail and architecture Apollo Design is recognized for creating innovative and award winning products of superior quality and value Focused on you our goal is to ensure unparalleled support from the initial conversation to after sales service Our lighting experts and engineers will consult with you on ways to use our standard products or engineer custom solutions Allow your imagination to run free Let the Apollo Design team help you create the lighting design you only imagined There is virtually no limit to what we can do together flor Joel Nichols Owner CEO Apollo Design Technology Product Description Congratulations on the purchase of your MultiSpot HT3012 Apollo Design is proud to be the exclusive USA distributor The MultiSpot HT3012 provides medium flood dispersion massive power density and quiet operation packed into a road ready all metal construction c
5. abinet USER MANUAL MULTISPOT GI HT3012 High Power RGB LED Lighting Fixture For firmware 50 010 0018 00111 1 00 RevL ENGLISH Page 2 15 sAN MULTIFORM Updated versions of this document may be available at WWW MULTIFORM LIGHTING COM RevB 08 2013 Order code 12 010 0253 80102 1 01 User Manual Multispot GI HT3012 WW MULTIFORM z Introduction Dear customer congratulations on the purchase of a Multiform branded item and the trust having been put in us with this decision Multiform is one of the leading global manufacturers of professional lighting eguipment and has decades of experience in design production and guality assurance To meet your reguirements this unit has been designed and built to the highest standards so that we can assure you that you have made a good and satisfying investment To take full advantage of all possibilities and for your own safety and the safety of your environment please read these operating instructions carefully before you start using the unit m Description The MultiSpot GI HT3012 is a powerful yet compact RGB color mixing light fixture for indoor applications which range from architectural purposes to stage lighting With its compact design high efficiency drive electronics and advanced cooling system this fixture has been designed for both flexibility and reliability SAFETY INFORMATION Read the safety precautions in this chapter before installing powering up operating or s
6. any values from the DMX input but generates related DMX values on the output according to the selected pattern so that other similar units can show the same pattern if they are connected by DMX signal cables and set to mode d3 If you leave mode A for any reason and come back later into mode A the unit will recall the last chosen pattern even if the unit was switched off in between Pattern list Description Function of Knob 1 AO All off none A 1 Static scene Colour A 2 Soft fade red green Speed A 3 Soft fade green blue Speed A 4 Soft fade red blue Speed A 5 Soft fade red yellow Speed A6 Soft fade candy lime Speed AT Soft fade pink blue Speed A 8 Soft fade turquoise pink Speed AQ Soft fade red green blue RGB Speed A10 Hard switch red green Sound to light Speed A11 Hard switch green blue Sound to light Speed A12 Hard switch red blue Sound to light Speed A13 Hard switch red yellow Sound to light Speed A14 Hard switch candy lime Sound to light Speed V3 00 08 2013 10 User Manual Multispot GI HT3012 VY MULTIFORM A15 Hard switch pink blue Sound to light Speed A16 Hard switch turquoise pink Sound to light Speed A17 Hard switch red green blue Sound to light Speed A 18 Hard switch red yellow green turquoise blue pink Sound to light Speed A19 Random speed red yellow F
7. before the display switches off It will be switched on again if any key is touched and will switch off again after 25 seconds if the keys are not unlocked by the procedure mentioned above Termination To avoid interference the last unit of a DMX chain should be terminated Therefore the DIP switch 9 of the last unit in the DMX chain must be switched ON Switch on condition The unit always returns to the last mode before it was switched off in DMX modes however DMX values are cleared if power is switched off DMX signal drop condition The device will retain the status that it was in before the DMX signal got lost but potential tact settings will be automatically cleared m Maintenance This unit does not need regular maintenance The internal circuit is protected by a 250V 2A slow blow fuse 5x20mm fuse If this fuse fails this usually indicates an internal fault requiring servicing by a qualified engineer V3 00 08 2013 15 User Manual Multispot GI HT3012 WW MULTIFORM a Technical data MULTISPOT GI HT3012 PanelS OutpUl siisi nno aa la r o 1 panel 1680 Im LED configuration 12x3W RGB 3 in 1 12x1W red 12x1W green 12x1W blue OP CS s s train b at or Secondary 25 degrees DMX Control 8 protocol ooosornrnnn nn ee nen 3 5 Channels DMX 512 1990 IP Rathgar aaa e ainen 20 indoor Mains In pute sincsen E E EE AC100 250V 50 60Hz Power supply type max consumption 0c cceceeeeseee
8. each or exceed the limits of EN62471 risk group 2 and may hence reach to risk group 3 To avoid eye injury do not look into the beam from a distance of less than 8 5 m 27 ft 11 ins from the front surface of the fixture without protective eyewear such as shade 5 welding goggles At larger distances light output is harmless to the naked eye provided that the eye s natural aversion response is not affected Do not view the beam directly with optical instruments such as magnifiers telescopes binoculars or similar optical instruments that may concentrate the light output Ensure that during setup and DMX programming no persons are inside a 8 50m 27 ft 11 ins vicinity of the device s front surface to avoid that they may accidently be exposed to the light beam User Manual Multispot GI HT3012 WV MULTIFORM 2 Where the mains plug or an appliance coupler is used as a dis connect device such device shall remain readily operable 3 To pull the AC Cord out of the wall outlet or the uni s AC socket never pull the cable itself but only the AC plug 4 Disconnect the unit from AC supply before any kind of cleaning on the product Use smooth and dry cloth only for cleaning 5 Do not expose this unit to any dripping or splashing liquids and do not place objects filled with liquids such as vases on the unit 6 Do not operate this unit near to open water or in high humidity 7 Choose the position of the AC cord according to the l
9. eeee eee ees switch mode 45W DMX ConnectionS 6 cc cece eee e eee eee e eee eee ee tees teeta ed 3 pin XLR Male Female Modulation Type ccccceceeeeee eens nn Pulse Density Modulation PDM Dimensions with straight bracket WxHxD 269 0 x 275 7 x 115 0mm AN a a E EA E a EEE ASEE 2 8kg m Standards This product complies with the following standards EU electrical safety nosnnnesnnneeeneerrnr eerren EN60598 1 2008 EN60598 2 1 1989 EU general safety eirinen akor riia k v sika kika EN60598 2 17 EU photobiological safety ooooonnn conn nooo EN 62471 2008 EU EMC 2isiissrr niinna infra EN55015 2006 A1 2007 EN61547 1995 A1 2000 P EE E con vania EN61000 3 2 2006 This product meets both the EMC Directive 2004 108 EC and the Low Voltage Directive 2006 95 EC Ask your dealer or visit www multiform lighting com for more information V3 00 08 2013 16 MultiSpo HT3012 NA APOLLO DESIGN Apollo Design Technology Inc 260 497 9191 ApolloDesign net Copyright 2015 Apollo Design Technology Inc 1 15
10. er carriage and correct grounding to ensure safe operation The AC power source must be eguipped with a circuit breaker and earth leakage detector Make sure to only use compliant AC supply lines gt B gt B gt m Getting started making DMX control connections Connect the Multispot GI HT3012 to a suitable DMX controller where needed and interconnect several units by means of their DMX In Outputs as reguired The last unit shall be eguipped with a proper 120 Ohm termination resistor eguipped DMX plug as shown in below drawing Please make sure that all used DMX cables comply to below standard DMX output DMX output DMX input DMX input TERMINATION AR feet g fs AN d f 055X 442 ae gt 6 3 5 Pin 3 Pin 5 Pin 3 Pin WIRE SIGNAL SHIELD GROUND RETURN OV INNER CONDUCTOR DATA COMPLEMENT INVERTED INNER CONDUCTOR DATA TRUE NON INVERTED V3 00 08 2013 8 User Manual Multispot GI HT3012 AN MULTIFORM m Operation All user controls are located on the rear bottom and side of the backpanel of the unit User interface overview 1 In A Mode Speed Control except A1 Mix Control In C Mode Level Control 2 Display showing the Mode DMX address LOC function etc 3 Indicates presence of a DMX signal 4 Indicates the sound activated mode internal microphone 5 MODE selection button 6 UP button 7 DOWN button 8 Internal microphone 9 Switches on the termination for the last unit in the DMX cha
11. er of this unit 2 Choose a location for operation where the unit is protected from vibration and where a fixed mounting position is provided In case of overhead mounting follow applicable rigging requirements 3 Before plugging the AC cord in the wall outlet check whether the AC plug the mains voltage and frequency are the same as this product is specified for If not contact you dealer immediately V3 00 08 2013 4 User Manual Multispot GI HT3012 WW MULTIFORM 4 The surface of the device may get hot during operation and heat sink areas may reach to or exceed the limits of EN60950 Do not touch heat sink areas of the device during operation and allow 20 minutes of cool down time after powering off before touching 5 If fluids have spilled into the unit or small parts have intruded the unit immediately switch off the unit and hand it over to the authorized service for a security check 6 Disconnect the unit from AC supply by pulling the AC plug out of the wall outlet or the uni s AC socket during a thunder storm in order to avoid any damage on the unit due to AC voltage peaks 7 In cause of not correct function of this unit or damaged AC cord or other damaged parts pull immediately the AC plug out of the wall outlet and hand the unit over to the authorized service for a security check 8 To meet all aspects of functionality and security during mainte nance work to be preformed on this unit all parts should be replaced b
12. ervicing this device Failure to do so may void the product warranty and releases the manufacturer from all product liability gt m Symbols used in this manual The following symbols are used to identify important safety information on the product and in this manual WARNING Read manual before installation operation or servicing WARNING Safety hazard Risk of injury or death WARNING Hazardous voltage Risk of severe or fatal electric shock gt gt b V3 00 08 2013 2 User Manual Multispot GI HT3012 PeDe AAN MULTIFORM WARNING Shock hazard Equipment must be properly grounded WARNING Hot surface Risk of skin burn or skin irritation WARNING Fire hazard WARNING Laser radiation Risk of surface damage WARNING LED light emission Risk of eye injury m Security advice before use gt oe oN gt V3 00 08 2013 General advice Read this manual completely before using the product Keep this manual in your records for future reference Follow all instruction printed in this manual Follow all printed security advice on the product itself Take care of enough distance between this product and sources of hum and noise like electric motors and transformers Carry this product with greatest care Punches big forces and heavy vibration may damage this product mechanically Protection from eye injury 1 Warning Depending on the configuration of the device this device may r
13. fetime is determined by the gradually declining brightness of a LED over time with a point of 50 brightness reduction marking the defined end of its lifetime The driving factor of this effect is the heat that the chip inside the LED is exposed to While a chip may under ideal circumstances reach to more than 100000 hours of lifetime the real world lifetime may only be 30000 to 50000 hours or less if the LED is exposed to excessive heat which can be caused by continuously running all LEDs inside this device at full power and operating the unit in high environmental temperatures If improving the lifespan expectancy is a priority take care of providing for lower operational temperatures This may include forced external cooling and or the reduction of overall projection intensity m Unpacking Please check that the box contains the following items and contact your dealer immediately for replacement if any part is missing Main parts 1 pc Multispot GI HT3012 passive RGB LED panel 1 pc PS020A 2 DMX controlled 3 channel power supply 1 pc Power cord 1 pc Operation manual m Getting started choosing a location Risk of fire The Multispot GI HT3012 has been designed to work in dry indoor environments at environmental temperatures up to 35 degrees Celsius For proper operation the unit must be operated with its heatsink side of the power supply up and unobstructed air convection to the heatsink Note Do not operate the Multispot GI HT3
14. in 10 Switching the display on or off with delay 11 Maintenance not in use 12 Power Input 90 250V AC 13 DMX Output connector 14 DMX Input connector V3 00 08 2013 9 User Manual Multispot GI HT3012 vyv MUL TIFORM Upon the users choice the unit can work stand alone or may be controlled by external DMX controllers Available modes A Auto Mode Press the MODE button 5 until the first digit on the display shows A indicating operation in A AUTO mode Then choose your desired pattern by using the UP DOWN buttons 6 7 see list below Changing the setting becomes effective 1 second after the new setting is made to allow stepping through presets without previewing all intermediate presets NOTE The A Mode is automatically disabled and can not be chosen when an external DMX signal is received DMX indicator LED 3 is lit Whilst being in pattern A 1 static scene turning knob 1 determines the mix whereas being in one of the other 26 patterns knob 1 controls the speed or selects the sound activated function refer to below pattern list The sound activated function can be activated by setting the knob 1 inside the first 10 degrees of its travel from left detent and it works from a built in microphone 8 which picks up the environmental sound Its activity is shown by the flashing of the right dot 4 in the display The level for all patterns is maximum In A mode the unit does not receive
15. ire Base speed A20 Random speed green blue Ocean Base speed A21 Random speed red blue Plush Base speed A22 Random speed red green blue RGB Burst Base speed A23 White strobe Sound to light Speed A24 Red strobe Sound to light Speed A25 Green strobe Sound to light Speed A26 Blue strobe Sound to light Speed A27 Strobe chase red green blue Sound to light Speed C Colour Mode Press the MODE button 5 until the first digit on the display shows C indicating operation in C mode Then choose by using the UP DOWN buttons 6 7 one of the 19 presets as shown in the list below Changing the setting becomes effective directly Knob 1 determines the output level In C mode the unit does not receive any values from the DMX input but generates related DMX values on the output according to the selected pattern so that other similar units can show the same behaviour if they are connected by DMX signal cables and set to mode d3 NOTE The C Mode is automatically disabled and can not be chosen when an external DMX signal is received DMX indicator LED 3 is lit If you leave mode C for any reason and come back later into mode C the unit will recall the last chosen mix even if the unit was switched off in between Available colour presets co all off C10 Frog C1 Red C11 Lavender C2 Green C12 Candy C3 Blue C13 Peach C4 Yellow C14 Aqua
16. l of the unit by any external DMX signal sending on the chosen channel In this mode the potentiometer 1 is disabled The unit receives DMX values on a packet of five channels and mirrors the received data on the DMX output 13 If a DMX signal is present the DMX LED 3 will turn on The five channels control the unit as follows DMX channel Value Range Function CH1 000 255 Red Intensity CH2 000 255 Green intensity CH3 000 255 Blue intensity CH4 000 255 Master dimmer CH5 000 255 000 049 Strobe off 050 255 Strobe rate 050 slow 255 max speed 23 Hz This setting is stored even if the device is switched off P DMX Preset Mode If you want to run the pre programmed patterns and scenes by an external DMX controller you can use the DMX Preset Mode Press the MODE button 5 until the display shows dP indicating operation in P DMX Preset mode Set the DMX starting address by simply using the UP DOWN buttons 6 7 The chosen DMX address comes effective approximately 3 seconds later and will show up on the display 2 in alternation to the dP The unit receives DMX values on a packet of four channels and mirrors the received data on the DMX output 13 If a DMX signal is present the DMX LED 3 will turn on The four channels control the unit as follows If DMX value of channel 3 is lower than 50 the unit works with static colours DMX Channel Va
17. lue Range Function CH1 000 255 Output mix choice from presets see C mode CH2 000 255 Master level CH3 000 049 Static mix mode active CH4 000 049 Tact off 050 255 Tact 050 slow 255 max speed 23 Hz V3 00 08 2013 13 User Manual Multispot GI HT3012 WW MULTIFORM Output mix presets can be activated by means of CH1 whilst the chosen mix can be adjusted with CH2 If the value of CH4 is above 50 the unit is set to tact mode The tact speed for any fixed output mix chosen on the first channel can be adjusted from zero value lt 50 to 23 cycles per second value 255 If DMX value of channel 3 is equal or higher than 50 the unit works in pattern mode CH1 Pattern CH1 Pattern 000 015 Soft fade red green 136 150 Hard switch green blue 016 030 Soft fade green blue 151 165 Hard switch red blue 031 045 Soft fade red blue 166 180 Hard switch red yellow 046 060 Soft fade red yellow 181 195 Hard switch candy lime 061 075 Soft fade candy lime 196 210 Hard switch pink blue 076 090 Soft fade pink blue 211 225 Hard switch turquoise pink 091 105 Soft fade turquoise pink 226 240 Hard switch red green blue 106 120 Soft fade red green blue RGB 241 255 Hard switch red yellow green 121 135 Hard switch red green turquoise blue pink DMX Value range Function CH2 000 255 Level CH3 050 255 Chase speed CH4 000 049 Tact off 050 255 Tact 050 slow 255 max speed 23 Hz
18. owest risk of damage by foot steps or by squeezing it 8 Do not open the unit for service there are no user serviceable parts inside Warranty will be void in any case of unauthorized service by the user or other not authorized persons Protection from fire AAN 1 Take care of not placing the unit near sources of heat e g powerful amplifiers fog machines Protection from electric shock 1 Only connect this unit to a mains socket outlet with protective earth connection ground fault earth fault and overload protection 2 Allow at least about 0 15m 6 ins between this unit and other devices or a wall to allow for proper cooling 3 Take always care of sufficient air convection in the unit s environment to avoid overheating Make sure air convection slots are not blocked Do not operate this unit in environmental temperatures exceeding 40 degrees Celsius 4 Be sure this fixture is kept at least 0 75m 30ins away from any flammable materials decoration etc 5 Do not stick filters masks or other materials directly on the LEDs or the LED cover screen 6 Check the total maximum power of your AC wall outlet if you connect several units to one wall outlet and avoid any overloading 7 If the device itself has an AC outlet for providing power to other units make sure to not exceed the specified maximum load Protection from injury and damage A 1 Never use any accessories or modifications not authorized by the manufactur
19. ows the DMX starting address You can choose any DMX starting address by simply using the UP DOWN buttons 6 7 The chosen DMX address comes effective approximately 3 seconds later and will show up on the display 2 in alternation to the d This allows control of the unit by any external DMX signal sending on the chosen channel In this mode the potentiometer 1 is disabled The unit receives DMX values on a packet of four channels and mirrors the received data on the DMX output 13 If a DMX signal is present the DMX LED 3 will turn on The four channels control the unit as follows DMX channel Value Range Function CH1 000 255 Red intensity CH2 000 255 Green intensity CH3 000 255 Blue intensity CH4 000 127 Master dimmer 128 227 Strobe 128 slow 227 max speed 23 Hz 228 255 Master dimmer full on Strobe off This setting is stored even if the device is switched off V3 00 08 2013 12 User Manual Multispot GI HT3012 AAN MULTIFORM d5 Mode DMX 5 Channel Split Master Strobe Mode Press the MODE button 5 until the display shows d5 indicating operation in d DMX mode Shortly after that the display shows the DMX starting address You can choose any DMX starting address by simply using the UP DOWN buttons 6 7 The chosen DMX address comes effective approximately 3 seconds later and will show up on the display 2 in alternation to the d This allows contro
20. utside areas where persons may walk by or be seated Make sure that the installation area can hold a minimum point load of 10 times the device s weight In fixed installations fix the unit with self locking screws nuts to the mounting point When mounting the unit to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke Where required secure the installation with an appropriate safety cable Always use a certified safety cable according to DIN56927 that can hold 12 times the weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails Never stand directly below the device when mounting removing or servicing the fixture Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The installations should be re inspected every year Make sure to comply with applicable cooling requirements if any V3 00 08 2013 7 User Manual Multispot GI HT3012 WW MULTIFORM m Getting started making AC supply connections Risk of fire Safety risk The Multispot GI HT3012 reguires an AC power source with sufficient pow
21. y genuine spare parts Consequently take care of your dealer or maintenance company to be authorized by the manufacturer z Health advice This unit produces and absorbs electromagnetic radiation The strength of radiation and the sensitivity for disturbing interference matches the CE and FCC requirements A corresponding sign is printed on the backside of the unit Any change or modification may affect the behavior of the unit concerning electromagnetic radiation with the CE requirements eventually not to be met any more The manufacturer takes no responsibility in this case z Functional advice This unit is immune to the presence of electromagnetic disturbances both conducted and radiated up to a certain level Under peak conditions the unit is classified to show a class C performance criteria and may encounter temporary degradation or loss of function which may need manual help to recover In such case disconnect the AC power from the unit and reconnect it again to recover z Environmental advice This unit is built to conform to the ROHS standards and the WEEE directive 2002 96 EC of the European Parliament and of the Council of the European Union Under these regulations the product shall not be discarded into regular garbage at the end of its life but shall be returned to authorized recycling stations La Q V3 00 08 2013 5 User Manual Multispot GI HT3012 AN MULTIFORM z LED Lifetime advice LED li
Download Pdf Manuals
Related Search