Z-Wave® Lamp Dimmer User`s Manual - Pepper
Contents
1. Z Wave Lamp Dimmer N User s Manual Table of Contents Safety Instructions eere 3 CopyrigliL 2 eicere eer niter trennen s 3 Trademarks 1 5 2 2 2 eiie cscvedeticessve 3 Introd ction hee 4 II B anaana 4 Package Contents esee 4 Connection Diagram pp 5 1 Product Overview ee 6 2 Solo Mode eie hene 7 Connection 7 Operation 2 ne cete ice 7 LED Indicator Solo 3 Remote mode 5 n ererernire treten Connection edoceri cese eet dee das Pairing the Controller LED Indicator 4 11 4 Remote the Slave Device 12 Connectionin 55 oa doe LIP ND ect ah ee 12 Operation M 12 Addition Information 13 PANE RR EIER 13 Wireless Range pp 13 Regulatory Compliance Stes FCC Conditions intei tn 14 WEEE Information teretes 14 Specification eese 15 Before attempting to connect operate or adjust this product please save and read the User s Manual completely The style of the product shown in this User s Manual may be different from the actual unit due to various models Safety Instructions Always read the safety instructions carefully m Keep this User s Manual for future r2. 5 To turn off the lamp dimmer press Dim button again LED Indicator Solo Lights up Q Lights f Flashing gt EJ po Green LED Lamp s light is on Lamp s light is off A t ap go Adjust the brightness of lamp al 3 Remote mode Connection Local control mY Z Wave d Connection Z Wave Computer USB Dongle Remote control Z Wave USB Dongle o Z Wave Connection Computer SD gt Turn on off or adjust the Broadband brightness of the lamp Modem Note To avoid any dangerous incidents from happening DO NOT plug this device onto extension nor use as extension The Z Wave controller such as Z Wave Dongle is not included in this package To install this lamp dimmer an enabled Z Wave controller is necessary Pairing the Controller 1 Plug the lamp dimmer into an available wall outlet in your desired location 2 Short press the Dim button three times to pair with the controller Before the pairing a Z Wave network and controller must be enabled To enable the Z Wave controller refer to it s instruction manual for more details 3 Once the lamp dimmer has been detected the confirm information will display on the control panel of the Z Wave controller 4 Configure it to a specific button or other else on the control panel of Z Wave controller Refer to the controller s instruction manual for more details 5 Pl
3. eference Keep this equipment away from humidity m If any of the following situation arises get the equipment checked by a service technician The equipment has been exposed to moisture The equipment has been dropped and damaged The equipment has obvious sign of breakage The equipment has not been working well or cannot get it to work according to the User s Manual Copyright This document contains proprietary information protected by copyright All right are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer Trademarks All trademarks and registered trademarks are the property of their respective owners or companies Introduction The lamp dimmer allows you to turn on off and adjust the brightness of the connected lamp wirelessly using a Z Wave protocol remote control With this technology you can remote control the connected lamp which located at your home through a computer s connectivity with Z Wave USB dongle when you are away from home Features m Simple plug and play installation m Support incandescent or dimmable halogen lamp up to 300W m Control on off dimming function manually with dim button or remote control by PC equipped with Z Wave certified USB dongle m Fully compatible with Z Wave enabled network and capable of communicating with any Z Wave certified device m All prod
4. fication Item Description Protocol Z Wave Multilevel Command Class Module Type Plug connection Max Loading 300W Operating Voltage AC110 120V 60Hz LED Indicator Bicolor LED Green Red Switch On Off Dim button Frequency 908 42MHz US Operating Rang Up to 100 feet 30m Data Rate 40kbps Application Indoor use Working Operating Temperature 0 40 C Environment Storage Temperature 10 80 C Dimensions 67 9 x 89 3 x 57mm Included the LxWxH height of wall outlet plug Weights 120g Housing PC8600 Flame Class UL 94 V 0 Compliance FCC UL Z Wave Lamp Dimmer User s Manual 0328 v1
5. or gateway It uses simple reliable low power radio waves that easily travel through walls floors and cabinets All products featuring the Z Wave logo are certified to work with one another Wireless Range The lamp dimmer is made wireless by Z Wave technology Typically the transmission distance is approximately 100 feet 30m When installing the module consider an open area with little obstruction for the best signal and performance Avoiding the obstruction between the module and controller may make a negative effect on wireless performance and range Regulatory Compliance FCC Conditions This equipment has been tested and found to comply with Part 15 Class B of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference FE received and include interference that may cause undesired operation WEEE Information For EU European Union member users According to the WEEE Waste electrical and electronic equipment Directive do not dispose of this product as household waste or commercial waste Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country For information on recycling of this product please contact your local authorities your household mmm waste disposal service or the shop where you purchased the product Speci
6. ucts other than this Lamp Dimmer itself are sold Separately Package Contents Z Wave Lamp Dimmer x1 m User s Manual x1 Connection Diagram Local control Lamp Dimmer Z Wave Connection Z Wave Computer USB Dongle Remote control Connection Computer d 1r 4 Turn on off or adjust the Broadband brightness of the lamp Modem The diagram shown here is an example only The application may be different from the actual conditions 1 Product Overview Dual LED Indicator Dim Button Indicates the status of connection or operation refer to the LED Indicator section for more details Press to turn the connected device on off or adjust the brightness of the lamp El Z Wave Enabled Outlet This outlet is used to plug in the device you wish to operate such as a floor lamp DO NOT exceed the wattage more than 300 watts when using the lamp dimmer El Plug Plug the lamp dimmer into any available wall outlet 2 Solo Mode Connection Lamp Lamp Dimmer Note To avoid any dangerous incidents from happening DO NOT plug this device onto extension nor use as extension Operation 1 Connect the lamp to a wall outlet with the lamp dimmer 2 Short press the Dim button to turn the lamp on 3 Press and hold the Dim button to increase the brightness of the lamp 4 Short press the Dim button twice and hold the second to decrease the brightness of lamp
7. ug a desired lamp into the Z Wave enable outlet on the lamp dimmer then switch and remote the lamp using your PC 6 To unpair with the Z Wave network disconnect from the controller s setting For more disconnection details refer to the controller s user manual Alternatively short press the Dim button three times and the third for over two seconds The lamp dimmer will unpaird and reset to the factory default LED Indicator Remote Lights up Q Lights off fli Flashing Q gt gt gt Green LED Red LED Unpairing 0 0 gt gt Transmitting Receiving 0 gt Adjust the brightness of lamp Lamp s light is on i D gt cf cu Lamp s light is off 11 4 Remote the Slave Device Connection Z Wave USB Dongle a Connection Computer Lamp Within 60m approx Operation 1 The lamp dimmer can be used as a brouter bridge router which allows you to remote the slave device using controller Note The slave device must support the standard Z Wave protocol 2 Connect the lamp dimmer slave device and controller to the same network To pair the slave device refer to it s instruction manual Addition Information Z Wave Z Wave is a state of the art wireless technology used as a standard for wireless home control It is a next generation wireless ecosystem that lets all your home electronics talk to each other and to you via a controller
Download Pdf Manuals
Related Search