Pulse AR III Brochure
Contents
1. 1 Attach the battery charger to the connection socket which is to be found at the backside of the electronic housing the same connection socket as mentioned under X Electronic unit back 2 The red LED displays the loading process Please note that this LED has to be active during the whole loading time 3 The green LED signalizes the end of the loading process The charging time normally takes 2 3 hours 4 After the loading process is completed remove the charging cable plug by pressing the lever under the connection socket The plug should be pulled out after every loading To prevent damages at the accumulator e g by overheating always pay attention to the loading times Close the loading process immediately after the accumulator is fully loaded Never load the metal detector without attendance or overnight KTS Electronic PULSE AR III XIII Technical data Search system Pulse indication Pl technic Depth efficiency Maximum search capacity with 2x2m searchcoil approx 6 m The metal indication is to be effected auditorially through loudspeaker headphone socket visually through display and colored LEDs Dimensions and weight Electronic unit 18 x 22 x 7 cm 1450 g Carrying case 42 x 36 x 9 cm 1550 g Aluminum telescope bar and searchcoil 1250g Smooth transportation The aluminum telescope bar is adjustable in hight and can also be demounted into 3 pieces Therefore th2. 6105 9111 50 Fax 49 0 6105 9111 55 www kts electronic com eMail mail kts electronic com Copyright 2008 by KTS ELECTRONIC Germany A duplication or usage of visual and textual content of this publication is not allowed without explicit consent KTS Electronic PULSE AR III 14 gem
3. not necessary Dictate your own speed during the search To search a large area within a very short time we recommend a speedy pace no jogging V Adjustment The metal detector PULSE AR III can be adjusted in no time 1 By using the turning knob MODE you activate the metal detector 2 Briefly press the RESET button in order to obtain a zero balance which is necessary for a failure free search 3 Adjust the FREQ regulator until a slow ticking signal is hearable This signal is acoustically similar to a seconds counter KTS Electronic PULSE AR III I VI Application of the RESET button The function of the RESET button is very important the button should be implemented after every modification After every turn on procedure after every change of MODE function after every swap of the searchcoil during the search if sound gets unstable due to poor soil conditions or earth magnetism While searching it must be observed that the sound is constant If this not should be the case it is possible that a magnetic field caused a misadjustment It also must be ensured that during zero balance no metal objects are located in the immediate vicinity of the metal detector This can produce a false calibration and unwanted indication effects Vil Indication of metal The indication of a metal will be shown through the left hand LED and the pulse tone Your device has a sound location system With the ap
4. CE PULSE AR Ill Metal Detector on the basis of pulse induction Instruction Manual KTS Electronic Germany VII VIII IX X Xl XII XIII XIV XV XVI XVI Table of Content MEF OGUICHON ptc ET 3 Volume of dellVGry eoocu idis eee iet Sota ee nne reel 3 DEiciripJI Mee 3 Appropriate handling eco eel cede tat nane beenden 4 hj rfe 4 Application of the RESET button 5 Indication of Metal 2 5 21 12 Ieoc ire eio esee ee prn nanana disaat 5 Search DIOCESS ge 6 Electronic unit front side eeeeee esses 6 Electronic unit Dack ce ener ern r eon eoo nenne rr nna nune nona arancE 8 Usage of appropriate searchcoils 9 Accumulator and battery charger 11 H ddemtrcpee m 12 uber mee 12 erc m M 13 L gal MOUCE e c 13 fugi B 14 XMIIEGCOnDISCGCL oh sssesxodescuuu x UredeRw corre cu O Ma FOROR e n eda OSProU OHIO E MKENC NUS 14 Introduction Dear customer Congratulations to your purchase of PULSE AR Ill a professionally built metal detector with discrimination and a depth lo
5. bject other metal parts are existent 5 Strongly magnetic interference fields within residential areas and in the proximity of ground cables can influence the measured values especially during the utilization of the large search coil 6 Disturbances often occur in the peripherals of radio stations 7 Strongly magnetic fields particularly in the proximity of high voltage masts can cause disfunctions XV Care Your PULSE AR III does nt need much care yet there are some points which you should consider in order to receive its optimal readiness for operation Protect the electronic housing with a plastic bag in case you should get caught by rain fog or dust Always keep your equipment clean and dry and wipe off sand and dirt Avoid extreme temperatures since it is not to be excluded that electronic units are damaged thereby Note Metal detectors produce magnetic fields in the searchcoil and can cause disturbances in the closer environment of certain industrial plants or electronic devices XVI Legal notice Before you start searching please note that the monument protection as well as other legal standards are relevant KTS ELECTRONIC assumes no responsibility for possible legal violations In case of doubts we recommend a comprehensive consultation with an attorney or national monument offices KTS Electronic PULSE AR III C2 XVII Warranty According to the following conditions see below we remedy d
6. cation up to 6 m and most efficient to search after precious metals gold silver platinum To avoid possible operating errors please read this instruction manual carefully We wish you much success with your new PULSE AR III and will be at your disposal if any questions should arise v Yv v WV Volume of delivery Electronic unit with built in storage battery leather bag and shoulder strap Mobile microprocessor controlled quick charger with car recharger connection at cigarette lighter and 110 Volt adapter Stereo headphones 25cm searchcoil incl telescope bar depending on equipment version 45cm searchcoil depending on equipment version Cylindric coil depending on equipment version 1x1m searchcoil 8 fold fragmented incl transport bag depending on equipment version Carrying case Installation Assemble the telescope bar For that purpose the central rod aluminum tube adjustable in length has to be positioned into the aluminum tube of the arm rest Afterwards connect the telescope bar with the aluminum tube of the searchcoil Wrap the searchcoil cable around the aluminum tube The electronic unit is protected by a bag through the lower opening in the bag the jack of the search coil must be plugged into the panel jack KTS Electronic PULSE AR III IV Appropriate handling Operate the searchcoil approx 2 to 5cm parallel to the soil Due to the pulse induction method a swiveling of the searchcoil is
7. e transportation of PULSE AR III is exceptionally comfortable in the provided bags and in the carrying case Due to the leather bag with its shoulder straps the electronic unit can also be transported effortlessly Electronic power supply There is a 12 V 2400 mA nickel cadmium battery attached to the metal detector so that a 12 hour operating time is guaranteed Through the mobile microprocessor controlled quick charger the metal detector is fully loaded within 2 hours A external car recharger for the connection to the cigarette lighter is also enclosed XIV Error signals In line with the development of your PULSE AR III great emphasis was placed on stability and the avoidance of incidences Despite the multiplicity of filters and modulators it is unfortunately possible that certain soil conditions cause disturbances which can effect your measured values Apart from a wrong soil balance attitude incorrect signals can occur by following effects 1 Ferric oxide Through magnetic ferric oxide soils the conductance of the located metal can comprehend falsified data 2 Anomaly effects lead to the fact that large iron metals are indicated as precious metal 3 Small parts of bronce partially may be indicated as iron the accuracy of the measured values is therefore ensured starting from 5x5cm in dimension KTS Electronic PULSE AR III NO 4 The measured values can be falsified because in the proximity of the located metal o
8. eficiencies free of charge if they are evidently based on manufacturing errors or defects and are reported to us immediately after assessment of damage within 24 months after delivery to the ultimate buyer Defective parts will be repaired gratuitous or will be replaced by efficient parts of our choice KTS reserves the right to exchange a device by an equal valued replacement unit in case the returned product cannot be required in an appropriate budget time frame On site repairs cannot be demanded Replaced resp exchanged parts will merge into our property The guarantee claim expires in cases of improper handling gross carelessness or when repairs modifications additionally installed parts or extentions are carried out from persons which are not authorized on our part to do so Guarantee claims will neither effect an extention of the term nor they will implement a new time limit Further requirements in particular such through extraneous causes resulting damages are excluded unless a commitment is not necessarily the case We therefore are not liable for any accidential indirect or other subsequent damages of any kind which lead to limited use data loss profit setbacks or operating failures After expiry of warranty KTS can agree upon a service after expiry of guarantee In this case repairing and shipment will be charged XVIII Contact KTS Electronic Kurhessenstr 1 D 64546 Morfelden Walldorf Germany Tel 49 0
9. lume control 5 RIGHT HAND LED The right hand LED serves the purpose of discrimination in DISC mode the left hand LED flashes when the optical indicator appears in the ALLM and DISC mode KTS Electronic PULSE AR III X Electronic unit back There are 2 connection sockets at the back side 1 Socket for coils The connector for the coil is on the left hand side The connector plug of the search coil has to be plugged into the socket Before removing the plug the jack must be pressed then the plug can be pulled out The connector is compatible with all searchcoils 2 Headphone socket Any commercial headphones with 6 3mm jack can be plugged in If you use the headphones the speaker is turned off Matching light weight headphones are provided with this device KTS Electronic PULSE AR III XI Usage of appropriate searchcoils According to the purpose PULSE AR III is applicable with various searchcoils 25 cm searchcoil The 25 cm searchcoil is the standard tube of PULSE AR III and is particularly suitable for the search after small metal objects 45 cm searchcoil Very convenient for the search after small medium sized and large metal objects Furthermore it has the benefit of a speedy uninterrupted search process Cylindric coil Through its dimensions of 5x20cm appropriate for the search in wells narrow excavations and underwater At the same time it can be helpful to find micro objects KTS Elect
10. proach of the searchcoil at a metal object the tone frequency will rise Once the soil is exactly over the object the highest tone is reached This method not only helps to locate the exact spot of discovery but it also detects based on the duration of the sound the object s shape Examples A long lasting high tone in longitudinal direction stands for a narrow object e g a tube a high tone in any direction calls for a circular object During search it often happens that side noises appear to be disruptive Therefore we recommend the use of the provided headphones KTS Electronic PULSE AR III Vill Search process To make the search result oriented and for this reason successful the following facts should be kept in mind gt modification of the tone frequency intensity of the tone gt continuity of the tone gt level of value display The modification of the sound is the first sign for the location of a metal object The more intensive the tone the larger the metal object and the nearer it is located to earth s surface While the tone is hearable the searchcoil should be moved in the near vicinity to find out the possible shape of the metal object The concurrent adherence to sound and display value leads to a better analysis of the discovered object IX Electronic unit front side The electronic unit is installed in a high quality box Besides the display there are 4 control elemen
11. ronic PULSE AR III 1x1m searchframe Preferably used for the deep sounding after medium sized and large metal objects During the search you should hold the searchcoil between 20 to 50cm over the ground The higher the distance to the soil the less small and medium sized metal objects are displayed Assembly of the 1x1m searchframe 1 Connect the pipes 8 pieces in numeric order Please note that the numbers should be readable on the upper side 2 Arrange the searchframe on a flat surface and be sure that the frame is straight 3 Afterwards the cable has to be placed on the pipe and fixed at the corners through the provided tape Please be sure that the cable and searchframe are firmly connected to each other KTS Electronic PULSE AR III e Turn off the metal detector in case you want to switch to another searchcoil then connect the selected searchcoil Please press the RESET button after you have started the detector again XII Accumulator and battery charger Your detector is equipped with 12V 2400 mA nickel cadmium battery With the help of the BATT mode you can check the current battery condition Through the mobile microprocessor controlled quick charger the metal detector is fully loaded within a very short time Due to the connectivity at the cigarette lighter this is also possible while you are on the move The loaded accumulator allows a operating time of approx 8 hours Loading process
12. ts attached to the front side 1 MODE The MODE knob can be switched to 4 positions DISC In this search mode the discriminator comes into operation Thereby an optical and acoustical discrimination takes place The different metals will be signaled through varying tones and conductivity values KTS Electronic PULSE AR III Examples for different conductivity values light metals e g aluminum 20 copper 40 gold silver platinum 100 and over ALLM This search mode shows all metals without discrimination Here the metals will not be tested for their conductivity Without discrimination they will be shown acoustically and optically through needle deflection This has the advantage that the search will be carried out with the highest sensitivity At the same time a depth measurement takes place which is visualized by needle deflection The shorter the needle deflects the deeper the metal is located Furthermore shape and size of the located object can be determinated through needle deflection BATT Scale to control the battery condition The battery is charged if the needle points to 100 or higher OFF The metal detector is switched off 2 RESET Automatic zero balance By pressing the RESET button the device will be adjusted unto the respective ground 3 FREQ Frequency setting controller the smaller the object you are searching for the smoother the adjustment must be 4 VOLUME Vo
Download Pdf Manuals
Related Search