View installation guide
Contents
1. DARING oe h WEU TRUT INSTALLATION BLACK ISO GRIPS FOR 1 BARS 6340 CUSTOMER SERVICE PARTS INCLUDED Right Throttle Side Grip Assembly Including INSTALLATION QUESTIONS ISO Grip Out cage Right Rubber Inserts Chrome Accent Ring End Cap 4 40 x 3 8 SHCS 18 8 Plastic Spacer Material Left Clutch Side Grip Assembly Including ISO Grip Out cage Left Rubber Inserts Chrome Accent Ring End Cap 4 40 x 3 8 SHCS 18 8 Tubes of Adhesive Installation Instructions LIMITED WARRANTY N os a ea Nanananana haana fg oe ck Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING KURYAKYN IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS WARNINGS CAUTIONS AND ATTENTION NOTES REGARDING THE USE AND CARE OF THIS PRODUCT WARNING THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY CAUTION This indication alerts you to the fact that ignoring the contents described herein can result in potential injury or material damage ATTENTION This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality ABOUT OUR CATALOG TOOLS SUGGESTED Razor Blade Sandpaper Electrical Tape STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE2. PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS PROCEDURE STEP 1 Read and understand all steps in the instructions before starting the installation Park the motorcycle on a hard level surface turn off the ignition and allow the engine to cool IMPORTANT If your bike has an open end throttle sleeve you must be very careful not to get glue between the sleeve and the bar This will permanently glue the bar to the sleeve leaving it inoperative The following instructions are written for closed ended throttle sleeves cont 6340 11 MC 0910 STEP 2 Remove the existing grips from the handlebars If unsure of procedure to remove grips consult the appropriate factory service manual When cutting away the existing grips be certain to not cut ee i through the throttle sleeve on the throttle side grip K U r Ud k U Ti STEP 3 With sandpaper or emery cloth remove all grip and adhesive residue from both the throttle sleeve right side and exposed handlebar left side If your throttle sleeve has ribbed marks or other protrusions it will have to be sanded or ground smooth to allow the grip to slide into place The surface should be completely clean and slightly roughed from the sanding With alcohol or similar degreasing agent and a clean rag wipe off the throttle sleeve and exposed handlebar STEP 4 Test fit each side The throttle side grip has a slightly larger inside diameter than the clutch side grip The grips should slid
3. d the inside of the grip to remove any contaminates Take the supplied tube of adhesive and squeeze a good amount of glue onto the throttle tube IMPORTANT The adhesive supplied sets up ALMOST INSTANTLY in the absence of air There is enough time to slide the grip into place but once it stops moving it cannot be adjusted STEP 4 In one smooth motion slide the grip onto the end of the bar all the way into position Rotate it back and forth slightly as you slide it on to help distribute the glue evenly and keep the grip from plowing the glue up against the switch housing Once in place squeeze the grip firmly to press the rubber against the bar and hold for 15 seconds INSTALLATION OF THROTTLE SIDE GRIP STEP 1 Decide if you want the grip s pads to match the clutch side when the bike is at rest or underway with the throttle slightly opened Without adhesive slide the grip into place and determine itsposition Make a mental note of the location or make a non permanent mark on the grip and or switchhousing STEP 2 Remove the grip and give it and the throttle sleeve a quick wipe to ensure they are free of contaminates Take the second supplied tube of adhesive and squeeze a good amount of glue onto the throttle tube STEP 3 Slide the grip into place rotating it clockwise as you slide it on to help distribute the glue evenly and keep the grip from plowing glue up against the switch housing Be prepared to quickly PAGE wipe away any
4. e into place with slight resistance If the grips slide on too loosely make a barber pole wrap around the bar or throttle sleeve with electrical tape PIC 1 INSTALLATION OF CLUTCH SIDE GRIP STEP 1 Some motorcycles have the switch housings pinned in place making it impossible to relocate them If the exposed handle bar on the clutch side is shorter than the length of the ISO Grip the end rubber will not be fully supported once installed Measure the length of exposed handlebar on the clutch side Measure the depth of the left grip Subtract the length of the handlebar from the depth of the grip this will give you the length of the spacer required Using a hack saw or utility knife cut the spacer to length and deburr Insert the spacer into the grip and slide it down as far as possible with your finger Slide the grip onto the handlebar to push the spacer all the way to the end STEP 2 With the left side grip still in place rotate the grip to determine the orientation that is most comfortable Make a mental note of the location or make a non permanent mark on the grip and or switch housing Remove the grip CAUTION USE EXTREME CARE WHEN USING THE GLUE INCLUDED IN THIS KIT READ ALL PRECAUTIONS AND AVOID CONTACT WITH SKIN OR EYES IT IS ALSO A GOOD IDEA TO COVER ANY AREA OF THE BIKE WHERE GLUE COULD POSSIBLY DRIP DURING INSTALLATION STEP 3 With alcohol or similar degreasing agent and a clean rag wipe off the exposed handlebar an
5. excess glue being plowed up by the grip that could be forced up against the switch housing Once in place squeeze the grip firmly to press the rubber against the bar and hold for 15 2 seconds Ride On BLACK ISO GRIPS FOR 1 BARS INSTALLATION
Download Pdf Manuals
Related Search