Hydraulic Slideout-Web.pmd
Contents
1. 3 Plug opening on manifold to prevent drawing air into the system 4 Energize the Power Unit to retract close room 5 Continue to run the room in and watch for fluid flow from hose port Fluid flow greater than a few drops will indicate internal cylinder leaking bypassing of piston seal If there is no fluid flow reconnect hose to E port and tighten WARNING Be sure to reconnect and tighten hose at the E port before attempting to extend open the room or the system will experience RAPID FLUID LOSS Contact qualified technician if there is excessive fluid flow The cylinder should not be repaired in the field Refill the Power Unit Reservoir as recommended on Page 10 of this manual 12 WIRING DIAGRAM YOLOW 595 9 ADNVHO 3SN4 ANY 3ONVS TIVLSNI OL HAIWOLSND AOYNOS 5 15 JO PIS SIU O ON 5 359 QT1O4INVIN y LL 5 IEM HOLIMS2. 49 LIPPERT COMPONENTS HYDRAULIC SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL TABLE OF CONTENTS 9 Prior to Preventative sees eeeseeeeeeeeeeeeneneneneeeeees Extending Slideout Retracting Slideout Auxiliary Ao Filling Adjustment Syncronizing Replacing Wiring LIMITED Warranty SYSTEM WARNING FAILURE TO ACT IN ACCORDANCE WITH THE FOLLOWING MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH The Lippert Hydraulic Slideout System is intended for the sole purpose of extending and retracting the slideout room I
3. is the one that is not powered The active slide tube is the one that has the cylinder attached If one side of the room fails to seal adjust as follows 1 Loosen bolts Fig 9A on top of the passive slide tube Fig 9B 2 Push or pull room on the passive side to align with the active side REMOVING AND REPLACING ACTUATOR To replace actuator 1 Take measurements A and B 2 Remove both nylock nuts 2 total from threaded shafts on actuator 3 Take note of jam nut locations and remove 4 After everything is disconnected slide actuator out of frame To replace with new actuator follow previous directions in reverse TROUBLESHOOTING CHART The following troubleshooting chart outlines some common problems their causes and possible corrective actions When reference is made to a Power Unit the term includes the motor and the actuator as a complete unit All Power Units are shipped from the factory with a serial number and date code which should be given to the service technician when asking for assistance ROOM DOESN T MOVE WHEN SWITCH IS PRESSED PROBABLE CAUSE CORRECTIVE ACTION Restrictions both inside and outside of unit Check for and clear restriction Low battery voltage blown fuse defective wiring Check battery Charge battery or add auxiliary power source Check battery terminals and all other wiring Look for loose or corroded connections Power Unit not functioning See Power Unit Troubleshooting
4. SYSTEM MAINTENANCE The Lippert Hydraulic Slideout System has been static tested to over 4 000 continuous cycles with out any noticeable wear to rotating or sliding parts It is recommended that when operating in harsh environments road salt ice build up etc the moving parts be kept clean and can be washed with mild soap and water No grease or lubrication is necessary and in some situations may be detrimental to the environment and long term dependability of the system Electrical System Maintenance For optimum performance the slide out system requires full battery current and voltage The battery must be maintained at full capacity Other than good battery maintenance check the terminals and other connections at the battery the control switch and the electric actuator motor for corrosion and loose or damaged terminals Check motor leads under the trailer chassis Since these connections are subject to damage from road debris be sure they are in good condition NOTE The Lippert Hydraulic Slideout System is designed to operate as a negative ground system A negative ground system utilizes the chassis frame as a ground and an independent ground wire back to battery is necessary see page 19 for wiring diagram It is important that the electrical components have good wire to chassis contact Over 90 of unit electrical problems are due to bad ground connections Mechanical Maintenance Although the system is designed to be almost main
5. page 20 Hydraulic Slideout Manual online at www lci1 com POWER UNIT RUNS ROOM DOES NOT MOVE Restrictions both inside and outside of unit Check for and clear restriction POWER UNIT RUNS ROOM MOVES SLOWLY Low battery poor ground extremely low Charge battery and check ground wire outdoor temperature Leaking cylinder See Checking for Bad Cylinder page 12 ROOM DRIFTS IN BOTH IN amp OUT POSITIONS Check for leaks in the hydraulic system Tighten fittings Air in system After checking all connections cycle pump several times in and out IN THE CLOSED POSITION ROOM DRIFTS OUT Leaking cylinder seal See Checking for Bad Cylinder page 12 Fluid bypassing cylinder piston See Checking for Bad Cylinder page 12 Hose from pump is leaking Tighten fitting or replace hose Air in system After checking all connections cycle pump several times in and out Loose mounting bolts Tighten mounting bolts IN THE OPEN POSITION ROOM DRIFTS IN Hose from pump is leaking Tighten fitting or replace hose Leaking cylinder seal See Checking for Bad Cylinder page 12 Fluid bypassing cylinder piston See Checking for Bad Cylinder page 12 11 TROUBLESHOOTING CHECKING FOR BAD CYLINDER 1 Retract close the slideout room completely 2 Loosen hose from E extend port on the manifold of the Power Unit WARNING Do not attempt to run room out with the E port hose loose The system will experience RAPID FLUID LOSS
6. racket located at the end of each guide tube 2 Loosen jam nut 3 For vertical adjustment turn vertical adjustment bolt B up or down to locate room height Once room is located tighten A and Jam Nut bolts Bolt MECHANICAL ROOM ADJUSTMENT CONT Nylock Nut Jam Nut 1 2 3 FREE TRAVEL Jam Nut 2 Adjusting room so it seals in the IN position 1 2 3 4 location Locate cylinder coming through the frame On the end of the cylinder there is a threaded shaft mounted to the drive bracket with 3 nuts Loosen the Jam Nut 1 and set Jam Nut 2 to desired location Tighten down the Nylock Nut against bracket Make sure Jam Nut 2 is adjusted for FREE TRAVEL see above Secure assembly by tightening Jam Nut 1against Jam Nut 2 This will change the of your seal going to the in position Adjusting room so it seals in the OUT position 1 2 3 4 Locate actuator coming through the frame On the end of the cylinder there is a threaded shaft mounted to the bracket with 3 nuts Adjust Jam Nuts 1 amp 2 one way or the other this will change the location of your seal going to the out position Make sure all nuts are tight SYNCHRONIZING ROOM TRAVEL The Lippert Electric Slideout System room travel both sides of the room traveling the same distance can be adjusted with specially designed synchronizing bracket mounted on the passive slide tube The passive slide tube
7. tch Fig 1C in the IN position until the room is fully retracted and stops moving 3 Release the switch which will lock the room into position NOTE If the slideout switch is held after the room in fully retracted the control will sense that the room has stopped and will shut off the motor after a few seconds 4 Install the transit bars if so equipped Fig 1 AUXILIARY OPERATION The Lippert Hydro Sync Slideout System can be run with auxiliary power devices like electric drills ratchet wrenches or cordless screwdrivers In the event of electrical or system failure this manual method of extending and retracting the slideout room can be used A standard handheld drill is all that is required A standard 38 room will take approximately 45 seconds to retract See the instructions below 1 Remove protective label See Fig 2 2 Using a standard hex bit insert into auxiliary drive device i e cordless drill or screwdriver or ratchet wrench 3 Insert hex bit into coupler found under protective label See Fig 3 4 Run drill forward or clockwise to extend slideout room and in reverse or counterclockwise to retract slideout room FLUID FILLING PROCEDURE Fig 4 Breather Cap The Lippert Hydraulic Slideout System uses automatic transmission fluid ATF Any ATF can be used A full synthetic or synthetic blend works best such as Dexron or Mercon 5 For best operation fill system within 12 of the
8. tenance free actuate the room once or twice a month to keep the seals and internal moving parts lubricated Check for any visible signs of external damage after and before movement of the travel trailer NOTE For long term storage It is recommend that the room be closed retracted WARNING FAILURE TO ACT IN ACCORDANCE WITH THE FOLLOWING MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH ALWAYS MAKE SURE THAT THE SLIDEOUT ROOM PATH IS CLEAR OF PEOPLE AND OBJECTS BEFORE AND DURING OPERATION OF THE SLIDEOUT ROOM ALWAYS KEEP AWAY FROM THE SLIDE RAILS WHEN THE ROOM IS BEING OPERATED THE GEAR ASSEMBLY MAY PINCH OR CATCH ON LOOSE CLOTHING CAUSING PERSONAL INJURY INSTALL TRANSIT BARS IF SO EQUIPPED ON THE SLIDEOUT ROOM DURING STORAGE AND TRANSPORTATION EXTENDING SLIDEOUT ROOM 1 Level the unit 2 Verify the battery is fully charged and hooked up to the electrical system 3 Remove the transit bars if so equipped 4 Press and hold the IN OUT switch Fig 1B in the OUT position until the room is fully extended and stops moving 5 Release the switch which will lock the room into position NOTE If the slideout switch is held after the room in fully extended the control will sense that the room has stopped and will shut off the motor after a few seconds RETRACTING SLIDEOUT ROOM 1 Verify the battery is fully charged and hooked up to the electrical system 2 Press and hold the IN OUT swi
9. top when all slideouts are completely retracted The see through reservoir makes easy to check oil level It is recommended that the oil level be checked prior to operating the system Make sure the breather cap is free of contamination before removing replacing or installing FILLING DIRECTIONS Remove Breather Fill Cap Pour ATF into Breather Fill opening NOTE Do not allow any contamination into reservoir during fill process NOTE reservoir holds approximately 2 quarts 1 89 liters of ATF Fill to within 2 of top Replace Breather Fill cap when finished NOTE System is self purging By simply cycling the system 2 3 times any air in the system will be forced back to the reservoir and out of the Breather Fill cap MECHANICAL ROOM ADJUSTMENT Vertical amp Horizontal Room Adjustment NOTE All slideout room adjustments must be performed by certified service technicians Adjustments made by non certified persons may void any and all warranty claims Horizontal adjustment 1 Loosen 2 carriage bolts A on each bracket located at the end of each guide tube 2 Room is ready to be positioned horizontally by pushing on the outside sidewall or by using a prying devise inserted into the opening between the room and coach 2 CE 5 5 NOTE Use caution when using prying devise so seals do not become damaged Vertical adjustment 1 Loosen 2 carriage bolts A on each b
10. ts function should not be used for any other purpose or reason than to actuate the slideout room To use the system for any reason other than what it is designed for may result in damage to the coach and or cause serious injury or even death Before actuating the system please keep these things in mind 1 Parking locations should be clear of obstructions that may cause damage when the slideout room is actuated 2 Be sure all persons are clear of the coach prior to the slideout room actuation 3 Keep hands and other body parts away from slideout mechanisms during actuation Severe injury or death may result 4 To optimize slideout actuation park coach on solid and level ground DESCRIPTION The Lippert Hydraulic Slideout System is a rack amp pinion guide system utilizing a hydraulic actuator to move the room assembly The power unite drives the cylinder rod in a forward and backward motion to drive the slide room in and out The Lippert Hydraulic Slideout System is designed to operate as a negative ground system PRIOR TO OPERATION Prior to operating the Lippert Hydraulic Slideout System follow these guidelines Coach should be parked on the most level surface available Leveling or stabilizing system should be actuated to ensure coach will not move during operation of Bed Lift System Be sure battery is fully charged Be sure to keep all persons and pets clear of Bed Lift System during operation RO NM
Download Pdf Manuals
Related Search