091218_D42A_DRL_INSTALLATION INSTRUCTIONS
Contents
1. GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION LED Daytime Driving Lights 2 APPLICATION ALTIMA SEDAN COUPE 2010 w o Foglamp PART NUMBER B66MO JAOOB Installation of this accessory requires installation of additional Nissan Genuine Part s OG for Sedan without foglamps OG Fog Lamp Bracket LH RH 26916 ZXOOA 26911 ZXOOA OG for Coupe without foglamps Bumper Finisher LH RH 62257 ZX10B 62256 10 4 KIT CONTENTS N X Uu Service Part Number amp Module RH B6600 JA001 amp Module LH B6600 JA002 ontrol Unit Accessory Engine Room Harness Accessory Main Harness Accessory Jumper Harness Tie Wrap L 150mm Tie Wrap L 200mm Double Sided Tape Butyl Tape Urethane Foam Tape Description 17 1 V U Cy O D lt U Z O c AJAN ejeje Njeje 2 Installation Instructions TOOLS REQUIRED Nylon removal tool Wire cutter 10mm Socket 21mm Deep Socket and driver Phillips screw driver Masking tape Flash light Scissors 100 alcohol Soap water Soft non linting towel Awl Page 1 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 6 PRE INSTALLATION CAUTIONS NOTES A CAUTION Dealer Installation Recommended Instructions refer to Service Manual Please read this instruction carefully before installing this product for correct installation Please DO NOT use or ins2. Hand Parking Brake Models only Disconnect parking brake connector PO1FB as shown in Fig 52 30 Hand Parking Brake Models only Connect parking brake connector PO1FB to Accessory Main Harness as shown in Fig 52 Accessory Main Harness Parking brake connector PO1FB m Accessory Main Harness Connection Detail Accessory Main Male Harness connector Female n connector Parking brake connector PO1FB Parking brake Female connector terminal Male terminal Page 18 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 11 LAMP MODULE INSTALLATION Sedan models only 1 Remove bolt and pull bumper finisher rearward at Pawl location as shown in Fig 53 2 Attach fog lamp bracket using bolt and pawl as shown in Fig 54 3 Attach Lamp Module LH with Bolts 2 and Nuts 2 as shown in Fig 55 Note Please take care of LED Daytime Driving Lights facial when installing brackets to avoid scratches 4 Repeat steps 1 through 3 for right hand side Accessory Engine Room LL LN 5 Reinstall vehicle parts and connect Lamp Harness to Harness connector k F ae Accessory Engine Room Harness as shown in Fig 56 1 IFA uk I Lamp Harness connector Page 19 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 11 LAMP MODULE INSTALLATION Coupe models only 1 Remove bumper finisher without
3. 8 Remove energy absorber from bumper reinforcement as shown in Fig 8 Energy absorber Page 5 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 9 VEHICLE PARTS REMOVAL CONT D 9 Remove USM module cover by pushing pawls 2 at locations shown in Fig 9 and pulling up on cover ps AL 7 33 S Fy 1 Af 77 m LL a 9 S Jf 3 Al F424 LL d IJ L r uU y j Jj FID Nn Or EI ES S Oar te P P Ae A Wl 10 Remove USM module harness cover by pushing pawls 2 at locations shown in Fig 10 and pulling up on cover Page 6 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 9 VEHICLE PARTS REMOVAL CONT D Fig 11 11 Remove instrument side mask LH as shown in Fig 11 Nylon EL T a Apply masking tape to prevent scratching trim removal 4 side mask LH Apply decas j ol parts b Use nylon removal tool to detach pawls clips and remove instrument side mask LH Masking tape 12 Remove instrument lower cover as shown in Fig 12 a Open fuse block cover and remove instrument lower cover screw b Pull downward at pawl locations to disengage pawls and clips C Pull back instrument lower cover and disconnect harne nn r clips Instrument ss connector clips lower cover 13 For Hand Parking Brake Models On
4. as shown in Fig 19 LH RH Page 8 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 9 VEHICLE PARTS REMOVAL CONT D 20 For Hand Parking Brake Models Only Remove center console assembly rear mounting screws as shown in Fig 20 a Remove screw covers 2 b Remove screws 2 2 Screws 21 For Hand Parking Brake Models Only Lift center console assembly disconnect harness clips connectors and remove assembly as shown in Fig 21 Page 9 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 10 WIRING HARNESS INSTALLATION ACCESSORY JUMPER HARNESS INSTALLATION Altima Base Model Only in case of no blue wire in place 1 below po _YX 220 1 If there is no Blue wire at NSO8MW CS oa F lt a um inserting male terminal from Accessory Jumper SEN 2s L tae c EEEA Harness into the place D necessary 3 Place f Joint connector of engine room harness and FEM harness See Fig 22 module a l aa s M ae FEM harness P a Engine room harness Engine room 2 Remove NSO8MW CS connector d N Q N N AN Blue wire NS08MW CS 3 Unlock Pin lock as shown in Fig 23 4 Insert male pin of Accessory Jumper Harness Accessory gt shown with climp side down as shown in Fig 24 Jumper Harness Engine room harness Crimp side facing downward a M aM R Male terminal 5 Push in b
5. fog lamp opening as shown in Fig 57 t ax Tr m py ed Bumper finisher without fog lamp opening 2 Attach Lamp Module LH with Bolts 2 and Nuts 2 as shown in Fig 58 3 Attach bumper finisher with fog lamp opening as shown in Fig 59 Note Please take care of LED Daytime Driving Lights facial when installing brackets to avoid scratches Bumper finisher with fog opening 4 Repeat steps 1 through 3 for right hand side 5 Reinstall vehicle parts and connect Lamp Harness to Accessory Engine Room Harness as shown in Fig 60 Harness connector Lamp Harness connector Page 20 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 12 O 1 O 2 O 3 4 13 O 1 O 2 O 3 4 14 O 1 CHECK AFTER INSTALLATION All connectors connections are secure Wire harness is properly secured No moving loose parts will cause a rattling noise Harness is protected not pinched or resting on sharp edges FUNCTION CHECK Re connect battery negative terminal Confirm daytime driving light is on when ignition switch is on and parking brake is off Confirm daytime driving light is off when position lamp is on Confirm daytime driving light is off when parking brake is on REINSTALLATION OF REMOVED PARTS All removed vehicle parts have been reinstalled A CAUTION Use caution when re installing vehicle par
6. shown in Fig 35 until vinyl grommet tape contacts grommet as shown in Fig 45 eS 17 Push Accessory Engine Room Harness Terminal WS vinyl tape 18 Seal hole and secure Accessory Engine Room Harness a Cut a 10mm wide strip of Butyl Tape b Seal hole in grommet with Butyl Tape as shown in Fig 46 C Clean panel with 100 alcohol and attach harness with Tape as shown in Fig 46 Corrugate tube Page 15 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 10 WIRING HARNESS INSTALLATION INSIDE WIRING HARNESS INSTALLATION Foot Parking Brake Models only Fig 47 19 Foot Parking Brake Models only Extra Connect plug on Accessory Main Harness to harness ZMS Accessory Engine Room Harness as shown in Fig i 47 20 Foot Parking Brake Models only Disconnect parking brake connector TBO1FB as shown in Fig 48 21 Foot Parking Brake Models only T A Connect the connector PO1FB and Accessary terminal y Parking brake Harness connector PO1MB as shown in Fig Pedal wo ee oe y Fig 48 22 Foot Parking Brake Models only aK f gt Parking brake Secure extra harness with Tie Wrap as shown in Sa ONS Fig 47 B N S LY XV 23 Foot Parking Brake Models only Secure Accessory Main Harness with Tie Wraps at N the positions shown in Fig 47 48 Parking brake Pedal MA L Accessory Main Harness Connection Detail Accessory Main Male Harness connect
7. 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 7 INSTALLATION OUTLINE Hand Parking Foot Parking Brake Models Brake Models 8 STANDARD CONNECTION METHOD USM ILL 0 5 Lg R NSO8MW TH16MW Connector of vehicle USM NS08MW 1B 0 5 Lamp module Parking brake PO1FB PKB Q ae e DE Control H Lamp P E module Connector of vehicle Parking brake d S O GND Page 3 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 9 VEHICLE PARTS REMOVAL 1 Apply protective tape to front fender and bumper LH RH as shown in Fig 1 2 Remove clips 6 from top surface of bumper as shown in Fig 2 3 Remove wheel and tire LH as shown in Fig 3 Fig 4 4 Remove screws 6 and clips 5 from bottom of bumper as shown in Fig 4 Front bumper Screws 3 View A Screws 3 Page 4 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 9 VEHICLE PARTS REMOVAL CONT D 5 Remove clips 9 and screws 2 from front fender protector front rear LH as shown in Fig 5 6 Remove bolt LH RH holding front bumper to front fender as shown in Fig 6 Front bumper 7 Pull out on upper corners of front bumper to disengage from side bracket as shown in Fig 7 and remove front bumper Front bumper side bracket A CAUTION Take care to not damage the pawls on the Front bumper front bumper and side bracket
8. ach Control Unit RH at location shown in Fig 32 3i T ets Nl l Mu 3 Remove tape liner and attach Control Unit LH at location shown in Fig 33 Side View c 4 Secure Control Units with 200mm Tie Wraps iti Ti i RH LH as shown in Fig 34 A Y ie wrap Control s jll 200mm connect three ties reinforcement Double Sided Tape Page 12 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 10 WIRING HARNESS INSTALLATION OUTSIDE WIRING HARNESS INSTALLATION SJ am tdi 3 E i i N Control Unit 5 Fig 35 6 LH Head Lamp Tie s Control Unit Fig 36 ux terminal ANN Lower side ae NS dH Efe Accessory Engine Room Harness Fig 37 nt Ground TH16FW NSO0SFW Accessory Engine Room aeos NSO8FW FAT IT E HI M UMM Ms ral us Accessory Engine Room Harness Electrical tape b lt Page 13 of 21 Feed Accessory Engine Room Harness through bumper reinforcement Attach Accessory Engine Room Harness to control unit RH and secure with 150mm Tie Wrap as shown in Fig 35 7 Attach Accessory Engine Room Harness using 150mm Tie Wraps 6 and secure ground terminal to lower bolt at locations shown in Fig 36 8 Remove USM module connectors by pulling upward as shown in Fig 37 9 Unwrap electrical tape engine room harness as shown in Fig 38 10 Feed A
9. ccessory Engine Room Harness through engine room harness COT as shown in Fig 38 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 10 WIRING HARNESS INSTALLATION OUTSIDE WIRING HARNESS INSTALLATION 11 Connect Accessory Engine Room Harness to power Fig 39 supply harness and USM module as shown in Fig TH16FW 39 NSOSFW 7 Ze TH16FW NSOSFW NSOSFW NSO8FW Fuse Case Accessory Engine Room Harness 12 Attach Accessory Engine Room Harness using Accessory Engine 150mm Tie Wrap as shown in Fig 40 Room Harness 13 Attach Accessory Engine Room Harness using 150mm Tie Wrap as shown in Fig 41 Accessory Engine Room Harness Tie Wrap dis PeT USM module m E yx a a S D MN lt k i Sl 00000 CST aar Accessory Engine Room Harness 14 Attach Accessory Engine Room Harness to Hood lock cable using Urethane Foam Tape 2 places as shown in Fig 42 Tape Cut Cut Urethane Foam Tape Page 14 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 10 WIRING HARNESS INSTALLATION OUTSIDE WIRING HARNESS INSTALLATION Fig 43 15 Make hole in hood release cable grommet using awl as shown in Fig 43 Grommet CAUTION When piercing grommet use caution and do not cut wire 16 Enlarge hole using Phillips screw driver as shown in Fig 44 Terminal Fig 45 through grommet as
10. lack cover to lock pin as shown in Fig 25 Push in black cover to lock pin Page 10 of 21 B66M0 JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 10 WIRING HARNESS INSTALLATION ACCESSORY JUMPER HARNESS INSTALLATION 6 Unlock pawl on lever and disengage connector by USM module A pushing down front tab and pulling in the up um direction as shown in Fig 26 Connector TH20FW CS12 M4 7 Partially disengage connector cover lock so terminal from Accessory Jumper Harness can lock in place as shown in Fig 27 Connector TH20FW CS12 M4 8 Insert female pin into 3rd slot with climp side down as shown in Fig 28 rimp side facing ownward Female terminal Connector side EB seer ae eee Connector TH20FW CS12 M4 9 Push in cover to lock pin lock as shown in Fig 29 Connector TH20FW CS12 M4 USM module 10 Secure extra harness with Tie Wrap as shown in Accessory Fig 30 Jumper Harness Extra harness Tie Wrap Page 11 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 10 WIRING HARNESS INSTALLATION OUTSIDE WIRING HARNESS INSTALLATION Control Unit Fig 31 1 Attach Double Sided Tape 4 to Control Unit and Spacer as shown in Fig 31 Spacer Ay CAUTION Clean control unit surface and vehicle Double Sided u F mounting surface with 100 alcohol Tape 2 Remove tape liner and att
11. ly Remove control device selector plate as shown in b Lock pin Fig 13 a Put selector lever in drive D position and pull downward on knob cover Fig 13 b Remove lock pin c Pull up to remove control lever knob d Use nylon removal tool to remove control device selector plate 14 For Hand Parking Brake Models Only Remove control device selector plate as shown in Fig 14 a Put selector lever in neutral b Screw the gear handle counter clockwise and remove c Remove the control device selector plate with nylon removal tool Pass t s Pawl Control device selector Page 7 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 9 VEHICLE PARTS REMOVAL CONT D 15 For Hand Parking Brake Models Only Remove cluster lid D as shown in fig 15 Cluster lid D 4 Pawl 16 For Hand Parking Brake Models Only Remove storage bin or CD changer finisher as shown in fig 16 Storage bin CD changer S Pawl finisher Metal clip 17 For Hand Parking Brake Models Only Remove console side finisher LH RH as shown in Fig 17 Console side finisher LH 2 L32 Kor 18 For Hand Parking Brake Models Only o Remove center console assembly upper mountin D CCLI E SPP g screws 2 as shown in Fig 18 N MM Sb RES Sce n PERS NE J 4 Screws 19 For Hand Parking Brake Models Only Remove center console assembly side mounting screws LH RH
12. or Female M connector Parking brake connector PO1FB Parking brake Female connector terminal Male terminal Page 16 of 21 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 10 WIRING HARNESS INSTALLATION INSIDE WIRING HARNESS INSTALLATION Hand Parking Brake Models only Plug Room Harness 4 Tie Wraps Accessory Main Harness Hand Parking f Brake Models only T P Hand Parking W 2 Fig 51 2d Ig Brake Models only CCAir Accessory Main A n l I s o N DM Tie Wrap to vehicle bracket Page 17 of 21 24 Hand Parking Brake Models only Connect plug on Accessory Main Harness to Accessory Engine Room Harness as shown in Fig 49 25 Hand Parking Brake Models only Attach Accessory Main Harness using 150mm Tie Wraps 2 as shown in Fig 49 26 Hand Parking Brake Models only Pull back carpet as shown in Fig 50 27 Hand Parking Brake Models only Secure Accessory Main Harness on foaming agent using Urethane Foam Tapes and 150mm Tie Wrap as shown in Fig 51 B66MO JAOOB II REV 12 15 2009 INSTALLATION INSTRUCTIONS LED Daytime Driving Lights 10 WIRING HARNESS INSTALLATION INSIDE WIRING HARNESS INSTALLATION Hand Parking ATi 28 Hand Parking Brake Models only Brake Models only ait V BE Attach Accessory Main Harness using 150mm Tie Wraps 4 as shown in Fig 52 29
13. tall the part in ways other than what is described in this instruction manual If problem occurs during installation please contact Nissan dealer where you purchased the product Q Pay attention when removing trim parts to avoid breaking clips 1 Apply Parking Brake 2 Make sure the shift lever is engaged in P or N position 3 Record customer Radio Presets Preset 1 2 3 4 5 6 A S S S S e 4 Use seat and floor protection B Y T S 5 Open the hood of the vehicle C A J J T 6 Disconnect the negative battery terminal to prevent short circuits during installation 7 This part is to be installed at a vehicle body surface temperature of 65 100 F 8 Do not wash the vehicle for 24 hours after installing to prevent the double sided tape from peeling A CAUTION Care must be taken not to scratch or damage any components during the removal or replacement process 9 Remove the following vehicle parts in the sequence shown below 1 Tire and wheel 2 Front bmpr e 0l 3 3 Fender protector front LH tia 4 Fender protector rear LH 5 USM module cover 6 Instrument side mask LH 7 Instrument lower cover LH 8 Kicking LH 9 Dashboard side lower panel 10 Cluster lid D 11 Console finisher 12 Storage bin or CD changer 13 Instrument side panel LH 14 Instrument side panel RH 15 Center console assembly Page 2 of 21 B66MO JAOOB II REV 12 15
14. ts to avoid damage scratches breaking of mounting clips or pinching of the vehicle harness C 2 Clean interior of vehicle 15 O 1 O 2 O 3 O 4 O 5 O 6 O7 VEHICLE CHECK Remove all tools from the vehicle Inspect reinstalled vehicle parts for proper panel fit Turn ignition to ON position Reset radio presets to the recorded setting Confirm proper radio operation Initialize sun roof and power window operation Turn ignition to off position Page 21 of 21 B66M0 JAOOB II REV 12 15 2009
Download Pdf Manuals
Related Search