Cybex Eagle® Leg Extension Owner`s and Service Manual Strength
Contents
1. 11050 407 11050 408 a 11050 413 11050 414 12050 377 11050 776 11050 610 11050 999 11090 314 11090 374 11090 376 11090 385 11090 392 3900 441 4605 381 X 11100 360 11100 400 4605 511 4613 320 4613 328 4613 594 4705 332 k a 4 a iii 4715 336 51198 8500 026 AA033904 BR030213 BR030214 5070201 000211 2000006 FB030232 Cybex Eagle 11050 Leg Extension Owner s Manual Cybex Eagle Leg Extension DESCRIPTION PIN DETENT CLAMP BLOCK INSERT WT ROD 625 47 50 KNOB EXT INC WT CHANNEL EXTRUDED GUARD EXT INC WT CHANNEL COVER TOP COVER TOP CHASSIS TRAY BOTTOM COVER PULLEY PANEL SHROUD BACK PANEL SHROUD FRONT DECAL WEIGHT PLATE 10 290 FRAME FRAME DETENT PLATE HANDLE CUSHION PLATE LINK DETENT LINK CAM PLATE INPUT ARM CUSHION BAR DETENT HOUSING CAM STOP ECCENTRIC PLATE CAM SHAFT PIVOT PIVOT PIN PIVOT PIN PLATE ROUND MOUNTING GUARD COUNTERWEIGHT 3 87 COVER SHEET REMOVED 5 06 RETAINER SPACER REMOVED 5 06 PLATE DECAL CAM ADJUSTMENT DECAL DECAL START RLD CHASSIS PLACARD EAGLE LEG EXTENSION OWNER S MANUAL PIN DETENT END CAP RING HANDLE GRIP GRIP FOOT COVER DECAL CYBEX INTERNATIONAL WARNING LABEL END CAP BEARING HOUSING ROTATION DECAL INSERT PLASTIC 5 94 PIN DETENT ADJUSTMENT DECAL DECAL TOTAL RLD INSERT THREADED 375 16 x 562. 5 Maintenance Daily Procedures 5 1 Weekly Procedures 5 4 Yearly 5 6 Environment 5 7 Storage 5 7 6 Service Parts ListS ie Baas 6 4 Exploded View Diagram 6 5 Page i Cybex Eagle 11050 Leg Extension Owner s Manual 1 Safety Safety Read the Owner s Manual carefully before assembling servicing or using the equipment It is the responsibility of the facility owner and or owner of the equipment to instruct users on proper operation of the equipment and review all labels A WARNING Serious injury could occur if these safety precautions are not observed User Safety Precautions Obtain a medical exam prior to beginning an exercise program Read and understand warning labels and user manual prior to exercising Obtain instruction prior to use AR Keep body and clothing free from and clear of all moving parts Inspect machine prior to use DO NOT use if it appears damaged or inoperable DO NOT attempt to fix a broken or jammed machine Notify floor staff Use the machine only for the intended use DO NOT modify the machine Be sure that the weight pin is completely inserted Use only the pin provided by the manufacturer If unsure seek assistance Never pin the weights in an elevated position DO NOT use the machine if found in this condition See assistance from floor staff Childr
3. J Place lower snap ring and wave washer onto guide rod about 3 from the top end of guide rod K Raise guide rod up through mounting hole and install the upper snap ring Increment L Lower guide rod and secure lower snap ring Weight Repeat steps 6J 6L for the other guide rod Adjusting Knob 7 Belt Routing A Verify belt is routed through top of pulley bracket Figure 7 and then route end of belt down to the top weight B Verify the belt clamp on the top weight is positioned properly with the top pulley NOTE The belt must have a straight path from the pulley to the belt clamp See Figure 7 NOTE Figure 7 shows the top view looking from the top pulley down to the top plate Assembly Page 4 3 Cybex Eagle 11050 Leg Extension Owner s Manual Slide belt through slot in belt clamp Verify belt and insert are installed properly as shown in Figure 8A NOTE Do not install the insert backwards as shown in Figure 8B Pull belt tight and secure belt to clamp with the two set screws NOTE Torque set screws 300 350 in Ibs See Figure 9 Place weight stack pin in each plate to verify proper installation Without selecting any resistance lift top weight up and down simulating normal operation Have an assistant verify that the belt is moving smoothly and is routed straight from the top pulley bracket to the top weight belt clamp Reinstall the six increment weights that were removed in step
4. Extension Owner s Manual This page intentionally left blank Service Page 6 2 Cybex Eagle 11050 Leg Extension Owner s Manual LEG EXTENSION PRODUCT NO 11050 NOTE See exploded view diagram for location of J serial number decal N belt and O 52 DESCRIPTION PART NO DESCRIPTION PART NO A Caution Decal eseeeeee 8500 026 11090 385 Warning 4605 381 J Serial Number Decal Placard 2608 11050 610 Wear Cover Item F 4800 134 D Eagle 8006 11040 789 L Wear Cover Item E 4800 093 E Leg Pad w Wear Cover 4800 006 Weight Selector Pin BH030207 F Seat Pad w Wear Cover 4800 131 N n GB000202 Back 4800 176 Cybex 3900 441 4605 507 Increment Weight Decal 11000 407 Service Page 6 3 PART NO 08229 11040 301 11040 401 11040 440 11040 750 11040 754 11040 751 11040 771 11040 768 11040 776 11040 777 11040 775 11040 760 11040 762 11040 560 11050 200 11050 201 11050 202 11050 203 11050 204 11050 205 11050 206 11050 208 11050 209 11050 210 11050 211 11050 213 11050 332 11050 333 11050 364 11050 374 11050 375 11050 387 11050 395 11050 400 11050 402 1 1 2 3 2 2 2 1 1 1 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 a
5. Manual for inspection and maintenance activities If you do not have a CYBEX Eagle Owner s Manual or if you have any questions or concerns call CYBEX Customer Relations at 888 462 9239 10 Verify proper operation 11 Anchor machine to the floor A NOTE NOTE NOTE Securely anchor machine to the floor using the anchor holes provided in each machine Cybex is not responsible for the actual anchoring of equipment Consult with a professionalcontractor Use fasteners having a minimum of 500 Ibs tensile capacity 3 8 grade 2 bolts or better If legs frame does not contact surface DO NOT pull down with anchors Shim any leg or frame not in contact with surface using flat washers Weight Stack SN Figure 15 Assembly Page 4 5 Cybex Eagle 11050 Leg Extension Owner s Manual This page intentionally left blank Assembly Page 4 6 Cybex Eagle 11050 Leg Extension Owner s Manual Chapter 5 Maintenance All preventive maintenance activities must be performed on a regular basis Performing routine preventive maintenance actions can aid in providing safe trouble free operation of all Cybex Strength Systems equipment NOTE Cybex is not responsible for performing regular inspection and maintenance actions for your machines Instruct all personne in equipment inspection and maintenance actions and also in accident reporting recording Cybex phone representatives are ava
6. and contact name your account number is helpful but not required The Return Material Authorization RMA system outlines the procedures to follow when returning material for placement repair or credit The system assures that returned materials are properly handled and analyzed Follow the following procedures carefully Contact your authorized Cybex dealer on all warranty related matters Your local Cybex dealer will request a RMA from Cybex if applicable Under no circumstances will defective parts or equipment be accepted by Cybex without proper RMA and an Automated Return Service ARS label Customer Service Page 3 1 Cybex Eagle 11050 Leg Extension Owner s Manual Call the Customer Service Hot Line listed above for the return of any item that is defective 2 Provide the technician with a detailed description of the problem you are having or the defect in the item you wish to return 3 Provide the model and serial number of your Cybex equipment 4 At Cybex s discretion the technician may request that you return the problem part s to Cybex for evaluation and repair or replacement The technician will assign you a RMA number and will send you an ARS label The ARS label and the RMA numbers must be clearly displayed on the outside of the package that contains the item s to be returned Include the description of the problem the serial number of the equipment and the name and address of the owner in the package along wi
7. risk of injury Perform the maintenance requirements as specified in the manual STANDARD COMPLIANCE Cybex products meet or exceed applicable ASTM and EN Standards A Warning Caution Decals Warning decals indicate a potentially hazardous situation which if not avoided could result in death or serious injury Caution decals indicate a potentially hazardous situation which if not avoided could result in minor or moderate injury The warning and caution decals are shown on the following page The diagrams following the decals show where each decal is located Safety Page 1 3 Safety Page 1 4 Cybex Eagle 11050 Leg Extension Owner s Manual A WARNING SERIOUS INJURY COULD OCCUR IF THESE PRECAUTIONS ARE NOT OBSERVED 1 Obtain a medical exam prior to beginning an exercise program 2 Read and understand warning labels and user manual prior to exercising Obtain instruction prior to use 3 Keep body and clothing free from and clear of all moving parts 4 Inspect machine prior to use DO NOT use if it appears damaged or inoperable 5 DO NOT attempt to fix a broken or jammed machine Notify floor staff 6 Use the machine only for the intended use DO NOT modify the machine 7 Be sure that the weight pin is completely inserted Use only the pin provided by the manufacturer If unsure seek assistance 8 Never pin the weights in an elevated position DO NOT use the machine if found in this conditio
8. 17mm X 19mm X 25mm BELT 95 WIDE PULLEY ASSEMBLY 3 50 BHSCS 250 20 X 625 BHSCS 375 16 X 875 BHSCS 375 16 X 1 00 BHSCS 375 16 X 2 00 BHSCS 375 16 X 2 25 BHSCS 375 16 X 2 50 BHSCS 375 16 X 2 75 S BOLT 250 X 500 190 10 24 INSERT 3 4 X 1 4 20 GROMMET NYLON SHCS 138 6 32 x 50 GR 8 LOCKNUT 190 No 10 24 NUT HEX SELF LOCKING 312 18 BLK ZINC LOCKNUT 250 20 NYLON LOCKNUT 375 16 NYLON LOCKNUT 375 16 NYLON LOCKWASHER SPLIT 312 WASHER SAE 375 WASHER USS 375 WASHER FLAT 387 ID x 1 753 OD X 06 WASHER SPRING 650 ID x 790 OD x 062 THK PHIL HEX WASHER HD TYPE 23 10 24 PN HD PHIL SC 8 X 625 BLK BALL STUD 312 18 UNC x 10 mm SET SCREW BHSCS 250 20 X 75 BHSCS 250 20 x 1 50 BHSCS 375 16 X 50 BHSCS 375 16 X 1 25 5 BOLT 375 1 25 8 FHSCS 375 16 0 FHSCS 375 16 5 INSERT PLASTIC 437 DIA 11 GA INSERT PLASTIC 1 50 x 3 00 x 11 GA INSERT PL 2 00 SQ 10 14 GA INSERT PL 1 50 SQ X 10 14 GA KNOB OVAL 375 16 x 1 25 MALE BUMPER WEIGHT BUMPER RECESS GRIP 1 38 OD X 94 ID 6 50 MOUNT CENTER BONDED STRIP FOAM 12 X 25 X ROLL DECAL INDICATOR DECAL SEAT ADJUSTING LOCKWASHER INT TOOTH 375 NUT HEX SELF LOCKING 312 18 ZINC SPRING RETAINING WASHER EAGLE PLAQUE TAP SC NO 10 24 X 50 PN HD PHIL BACK PAD SEAT PAD W WEAR COVER WEAR COVER LEG PAD W WEAR COVER WEAR COVER END CAP BUMPER RECESS SHCS 250 20X750 STUD 375 16 X 1 00 M
9. 2 12 UNC P WASHER WARRANTY BOOK NOT SHOWN DECAL CAUTION V PUSHER RETAINING RING 2 00 EXTERNAL RETAINING RING 625 DIA COM SPRING 56 x 66 1 50 LG DECAL PATENT PENDING GAS SPRING 250N BEARING RADIAL 17 mm EXT ED RACE Language Key 1 German 2 French 3 Spanish English Service Page 6 4 6 Japanese 7 Swedish 8 Russian amp e 2 3 o 4 4 4 4 4 4 nnn 0 4 6 PART NO FB030239 FB050211 FB130206 FB130207 6 000202 GP000209 HC620414 HC700416 HC700417 HC700426 HC700428 HC700430 HC700432 HD303312 HF 449063 HF540200 532812 HN575100 HN 60065 HN625200 HN704901 HN704902 HS328300 HS347600 HS347700 HS347702 HS407100 HT102214 542514 HX 60184 HY740000 JC620415 JC620422 JC700412 JC700420 JD343320 JC700922 JC700924 PP080207 PP090202 PP090210 PP090211 PP460011 PR060005 PR069400 4605 507 PR740300 PR250203 11000 394 11050 423 JS347400 HN664900 HS760100 11040 789 572512 4800 176 4800 131 4800 134 4800 006 4800 093 11100 361 PRO69400 HC622815 HP70717 13000 402 13000 400 HT552515 512517 11000 407 11040 790 DESCRIPTION CAM FOLLOWER 10mm BRG FLG 38 X 50 25 LG BEARING FLANGE 2 00 ID x 2 25 OD x 1 00 LG BRG FLG
10. 6B See Figure 10 Turn the Increment Weight Adjusting Kob to select all 15 Ibs 8 Install back shrouds A Assembly Page 4 4 Carefully place shroud assembly back into position on the two bottom screws See Figure 11 Install the top two screws securing the back shroud assembly See Figure 12 Correct belt routing Wrong belt routing Figure 9 Increment Weight Figure 10 Figure 11 QS Figure 12 6 Cybex Eagle 11050 Leg Extension Owner s Manual Install the three Phillips head screws securing the top back shroud See Figure 13 9 Install weight plate decals NOTE A NOTE You have the option to use pounds kilograms or both Slowly and carefully peel off back side of decal See Figure 14 NOTE When peeling off back cover make sure that the decals remain attached to the front sticker Align holes in decal with appropriate holes in weight stack NOTE Do not allow the adhesive to touch weight stack at this time Insert a guide pin through each hole of the template NOTE A guide pin can be anything that fits through the weight stack hole such as a weight stack selector pin Carefully align decal and rub it onto weight plates Carefully remove front side leaving decals adhering to weight plates See Figure 15 It is important that you perform regular inspection and maintenance activities on your equipment See the CYBEX Eagle Owner s
11. OLYBEX Cybex Eagle Leg Extension Owner s and Service Manual Strength Systems Part Number 11050 999 J www cybexinternational com OLYBEX Cybex Eagle Leg Extension Owner s and Service Manual Strength Systems Part Number 11050 999 J Cybex and the Cybex logo are registered trademarks of Cybex International Inc Eagle and its mark are registered trademarks of Cybex International Inc DISCLAIMER Cybex International Inc makes no representations or warranties regarding the contents of this manual We reserve the right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such revisions or changes Copyright 2010 Cybex International Inc All rights reserved Printed in the United States of America 10 Trotter Drive Medway 02053 508 533 4300 FAX 508 533 5183 www cybexinternational com techhelp cybexintl com 11050 999 J March 2010 Table of Contents 1 Safety Saey Sandie gai a edie gant 1 1 Warning Caution Decals 1 2 Regular Maintenance Activities 1 5 Using Proper Form 1 5 2 Exercises General Exercise Guidelines 2 1 3 Customer Service Contacting Service 3 1 Ordering 3 1 Return Material Authorization 3 1 Damaged Parts 3 2 4 Assembly oe latgeg ea bed te 4 1
12. OUNT WATER BOTTLE HOLDER HOLDER WATER BOTTLE TAP SC NO 8 16X 75 TAP SC 10 24 X 1 00 TYPE WB DECAL INCREMENT WEIGHT DECAL MADE IN USA Cybex Eagle 11050 Leg Extension Owner s Manual EAGLE 11050 11051 MAIN ASSEMBLY DETAIL SEE RLD ASSEMBLY DETAIL z Q SV RANNA ma Te TSS 9 BE Ae D 7 bist AN0 Service Page 6 5 Cybex Eagle 11050 Leg Extension Owner s Manual 11050 CAM ASSEMBLY DETAIL Service Page 6 6 Cybex Eagle 11050 Leg Extension Owner s Manual 11051 CAM ASSEMBLY DETAIL Service Page 6 7 Cybex Eagle 11050 Leg Extension Owner s Manual SHROUD AND GUIDE ROD ASSEMBLY DETAIL Service Page 6 8 Cybex Eagle 11050 Leg Extension Owner s Manual Belt Routing Assembly Detail Service Page 6 9 Cybex Eagle Leg Extension Owner s Manual Top Weight Assembly Detail QTY PART DESCRIPTION PART NO DESCRIPTION 11040 366 Top Weight Assembly Molded HS720004 Felt Washer 641 1 250 125 T 11040 367 Hub Molded HT562715 Tap SC NO 10 x 750 F Phil 11040 369 Rod Linkage HT582510 Tap SC NO 10 x 375 PN HD Phil 11040 370 Pin 11040 409 Molded Bumper Pad 11040 427 Rod 11040 572 Guard Increment Weight 11040 426 Stem 11040 573 Weight Increment 11040 424 Cover Plate 11040 216 Belt Clamp 11040 416 Cover
13. Top Weight 11040 301 Clamp Block Insert 11040 425 Knob 11040 428 Adjustment Decal BH030207 Pin Weight Selector 11040 429 Rotation Decal 4700 251 Lifting Post 15 HT552512 Screw Pan HD Phil HD Self BR030209 External Retaining Ring 188 Tapping 8 16 x 50 Type WB BR030220 Internal Retaining Ring 1 250 HY740000 Set Screw HP016820 Cotter Pin 125 X 1 25 4000 101 Weight Stack Plate HP266765 Roll Pin 125 X 938 4701 013 Weight Pack Not Shown TOURQUE SET SCREWS 300 350 IN LBS 1 1 2 2 1 1 1 1 1 1 1 4 2 1 1 NOTE Increment weights located in the increment weight channel See main assembly Service Page 6 10 OLYBEX 10 Trotter Drive Medway MA 02053 508 533 4300 FAX 508 533 5183 www cybexinternational com techhelp cybexintl com
14. ce Page 3 2 Cybex Eagle 11050 Leg Extension Owner s Manual 4 Assembly TOOLS REQUIRED 7 32 Allen wrench 3 4 Allen wrench 9 16 Wrench External snap ring pliers e Phillips screwdriver e Medium weight automotive engine oil e Torque Wrench NOTE Two people will be required for this procedure NOTE It is the responsibility of the facility owner owner of the equipment to ensure that there is appropriate clearance around each machine to allow for safe use and passage 1 Read and understand all instructions thoroughly before starting any of the procedures listed on this instruction sheet 2 Verify you have received the appropriate configuration A Verify that you received the correct color machine that you ordered B Verify you received weight plates and weight plate decals C Verify you received the Cybex Eagle Leg Extension Owner s Manual D Verify you received the warranty sheet 3 Move to desired location A Note the diminsions of the machine idle 61Lx46W x 58 H inches 154 94 x 116 84 W x 147 32 in use 61 Lx 46 W x 58 H inches 154 94 x 116 84 W x 147 32 Machine Weight 623 lbs 282 58 kg Determine if move your machine through the required doorway s If the machine fits through the the doorway s move machine to desired location and skip to step 5 If weight stacks need to be installed proceed to step 6 If the machine do
15. ear Immediately replace belt if any of the following conditions are present 3D View 3D or Side View Peeling of the belt s skin 0 Belt is necked down narrow section Replace belt if any section is over 1 32 03 Examine edge of belt narrower both sides Replace than rest belt if any section is of the belt narrower than the rest 0 gt more strands of kevlar hanging out NOTE Also replace belt if there is a significant amount of frayed kevlar Maintenance Page 5 4 Cybex Eagle 11050 Leg Extension Owner s Manual 3 Some machines use cables in addition to belts Inspect all cables for wear or damage and proper tension When inspecting cables run your fingers on the cable paying particular attention to bends in the cable and attachment points Replace all worn cables immediately The following conditions may indicate a worn cable e A tear or crack in the cable sheath that exposes the cable See Figure 1 Figure 1 Akink in the cable See Figure 2 Figure 2 A curled sheath See Figure Figure 3 e Necking a stretched cable sheath See Figure 4 Figure 4 Maintenance Page 5 5 Maintenance Page 5 6 Cybex Eagle 11050 Leg Extension Owner s Manual Inspect bars and handles for wear paying particular attention to tab area connecting points Replace all worn handles immediately Inspect
16. ecuring the back shroud See Figure 4 S lt SS H Carefully slide rear shroud upward and remove 6 Install the weight stack A Note how the increment weights are installed Figure 3 B With an assistant holding the increment weights move the adjusting knob to 0 Ibs and remove all six increment weights three each side Assembly Page 4 2 Cybex Eagle 11050 Leg Extension Owner s Manual C Using an external snap ring pliers remove the upper snap ring from one of the guide rods and carefully lower Upper snap ring the guide rod See Figure 5 D Remove lower snap ring and wave washer from the guide rod Repeat steps 6C and 6D to remove both snap washer rings from other guide rod Lower snap ring If possible lean guide rods outward away from machine in order to provide the most room for installing weight Guide rod plates F Slide top weight up and out of machine and carefully set Figure it aside G Wipe guide rods clean over entire length Lubricate with light coating of medium weight automotive engine oil H Carefully install each weight plate one at a time NOTE When installing weight plates position plates so wide edges of bushing face upward and narrow edges of bushing face downward See Figures 6A and 6B NARROW WIDE bushing bushing edge edge faces upward NOTE The narrow bushing edge must face downward Figure 6A Figure 6B l Slide top weight onto guide rods
17. ed immediately discontinue use until cable or belt has been replaced 3 Check for worn handles worn snap links and worn warning labeling Replace all worn parts immediately 4 Inspect for loose or worn grips Replace all loose or worn grips immediately 5 Inspect weight stacks for proper alignment and operation Correct all improper alignment and operation issues immediately 6 Lubricate guide rods using automotive engine oil only Yearly 1 Replace all cables and belts at least annually Using Proper Form Before working out read and understand the exercises located on the placard and in Chapter 2 Cybex Eagle 11050 Leg Extension Owner s Manual 2 Exercise Intended Use MUSCLES USED The intended use of this equipment is to aid or improve general physical fitness and exercise For Commercial use Instructions Read and understand all instructions and warnings prior to using this machine See Chapter 1 Safety in the Eagle Owner s Manual or consult with floor staff Quadriceps FINISH NOTE Motion Developed Knee Extension NOTE All adjustment points on the machine have yellow handles or knobs NOTE See next page for Set Up and Movement NOTE Do not turn knob when weight stack is elevated Exercise Page 2 1 Cybex Eagle 11050 Leg Extension Owner s Manual Set Up 1 Adjust back pad so that when seated your knees align with the machine s axis of rotation 2 C
18. en must not be allowed near these machines Teenagers must be supervised DO NOT use if guards are missing or damaged DO NOT use dumbbells or other incremental weights except those provided by the manufacturer Inspect all cables and belts and connections prior to use DO NOT use if any components are worn frayed or damaged DO NOT remove any labeling from equipment Replace any damaged labels Stop exercising if you feel faint dizzy or experience pain at any time while exercising and consult your physician Facility Safety Precautions Read the Owner s Manual carefully before assembling servicing or using the equipment Securely anchor each machine to the floor using the anchor holes provided in each machine NOTE Cybex is not responsible for the actual anchoring of equipment Consult with a professional contractor NOTE Use fasteners having a minimum of 500 Ibs tensile capacity 3 8 grade 2 bolts or better NOTE If legs frame does not contact surface DO NOT pull down with anchors Shim any leg or frame not in contact with surface using flat washers Safety Page 1 1 Cybex Eagle 11050 Leg Extension Owner s Manual e sure that each machine is set up and operated on a solid level surface Do not install equipment on an uneven surface sure that all users are properly trained on how to use the equipment e sure there is enough room for safe access and operation of the equipment Perf
19. es not fit through the door way s then see step 4 4 Doorway Instructions NOTE If your machine fits through the doorway then skip step 4 If your machine does not fit through the doorway then perform step 4 A Carefully remove each standard cone shaped shipping support using a 3 4 socket or wrench Assembly Page 4 1 Cybex Eagle 11050 Leg Extension Owner s Manual B With an assistant carefully remove the ten Button See a WT Head Socket Cap Screws BHSCS securing the BHSCS 4 S two halves of the frame See Figure 1 Carefully move each half through the door way to the desired location D With an assistant carefully attach each half together using the ten BHSCS removed in step 4B See Figure 1 E Continue on with step 5A 5 Replace shipping feet and remove the back 1 ge Locknut 2 shrouds BHSCS 2 A Carefully remove each standard cone shaped shipping support using a 3 4 socket or wrench Figure 1 B Carefully place rubber feet supplied with machine on each foot of the frame C Cut shipping tie securing top weight D Lift top weight and turn the Increment Weight Adjusting Knob to select all 15 lbs three increment weights each side E Remove the three Phillips head screws securing the top back shroud See Figure 2 F Loosen bottom two screws shown in Figure 3 NOTE Do not remove the bottom two screws 7 Remove the top two screws s
20. ilable to answer any questions or concerns that you may have CAUTION Use only Cybex replacement parts when servicing Failure to do so could result in personal injury NOTE All inspections and repairs must be performed by trained service personnel only Cybex will void warranty if non Cybex replacement parts are used Daily Procedures 1 Upholstery Wipe down all upholstery as per the recommendations listed below for light soiling and more difficult stains Light Soiling A solution of 10 household liquid dish soap with warm water applied with a soft damp cloth If necessary a solution of liquid cleanser and water applied with a soft bristle brush Wipe away the residue with a water dampened cloth Maintenance Page 5 1 Maintenance Page 5 2 Cybex Eagle 11050 Leg Extension Owner s Manual More Difficult Stains Dampen a soft white cloth with a solution of 10 household bleach sodium hypochlorite 90 water Rub gently Rinse with a water dampened cloth to remove bleach concentration The same procedure can be used with full strength household bleach if necessary Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately 30 minutes Rinse with a water dampened cloth to remove any remaining bleach concentration Alternative Method for Difficult Stains Dampen a soft white cloth with rubbing alcohol and rub gently Rinse with a water dampe
21. n Seek assistance from floor staff 9 Children must not be allowed near this machine Teenagers must be supervised 10 DO NOT use if guards are missing or damaged 11 NOT use dumbbells or other incremental weights except those provided by the manufacturer 12 Inspect all cables and belts and connections prior to use DO NOT use if any components are worn frayed or damaged 13 DO NOT REMOVE THIS LABEL REPLACE IF DAMAGED 4605 381 4 A P 2 CAUTION Keep away from moving parts Failure to do so could result in personal injury 8500 026 4 J Cybex Eagle 11050 Leg Extension Owner s Manual Leg Extension 11050 DESCRIPTION PART NO A Warning Label 4605 381 4 B Caution Decal 8500 026 4 Safety Page 1 5 Safety Page 1 6 Cybex Eagle 11050 Leg Extension Owner s Manual Regular Maintenance Activities Preventative maintenance activities must be performed to maintain normal operation of your equipment Keeping a log sheet of all maintenance actions will assist you in staying current with all preventative maintenance activities The preventative maintenance actions are described in detail in Chapter 5 Briefly they include Daily 1 Clean upholstery Weekly 1 Inspect all nuts and bolts for looseness Tighten as required 2 Inspect all cablesand belts for damage or wear see Chapter 5 If a cable or belt is worn or damag
22. ned cloth to remove any remaining rubbing alcohol concentration NOTE To restore luster a light coat of spray furniture wax can be used Apply for 30 seconds and follow with a light buffing using a clean white cloth Please Review Carefully When using strong cleaning agents such as rubbing alcohol or bleach it is advisable to first test in an inconspicuous area Other cleaning agents may contain harsh or unknown solvents and are subject to formula changes by the product manufacturer without notice Should you desire to use other cleaning agents carefully try them in an inconspicuous area to determine potential damage to the material Never use harsh solvents or cleaners which are intended for industrial applications To clean stained or soiled areas a soft white cloth is recommended Avoid use of paper towels Cleaning products may be harmful irritating to your skin eyes etc Use protective gloves and eye protection Do not inhale or swallow any cleaning product Protect surrounding area clothing from exposure Use in a well ventilated area Follow all product manufacturer s warnings CYBEX and its vendors cannot be held responsible for damage or injuries resulting from the use or misuse of cleaning products Frames Wipe down all frames using a mild solution of warm water and car wash soap Be sure to dry thoroughly AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the equi
23. of high humidity such as in the vicinity of a steam room sauna indoor pool or outdoors Exposure to extensive water vapor chlorine and or bromine could adversely affect the electronics as well as other parts of the machine Temperature The unit is designed to function normally in an environment with an ambient temperature range of 50 F 10 C to 104 F 40 C degrees Storage Humidity The unit can be shipped and stored in an environment with a relative humidity range of 10 to 90 NOTE Do not store the unit an area of high humidity such as in the vicinity of a steam room sauna indoor or outdoors Exposure to extensive water vapor chlorine and or bromine could adversely affect the electronics as well as other parts of the machine Temperature The unit can be shipped and stored in an environment with an ambient temperature range of 32 F 0 C and 140 F 60 C degrees Maintenance Page 5 7 Cybex Eagle 11050 Leg Extension Owner s Manual Maintenance Page 5 8 Cybex Eagle 11050 Leg Extension Owner s Manual 6 Service Please refer to the next several pages for parts lists exploded view diagrams NOTE All inspections CAUTION Use only Cybex replacement performed by trained service personnel only parts when servicing Failure to do so could result in personal injury Cybex will void warranty if non Cybex replacement parts are used Service Page 6 1 Cybex Eagle 11050 Leg
24. omfortably position shin pad and apply light pressure 3 Grasp handles and stablize body Movement 1 Push forward and up against the pad until your legs are straight in front of you Exercise Page 2 2 Cybex Eagle 11050 Leg Extension Owner s Manual 3 Customer Service Contacting Service Hours of phone service are Monday through Friday from 8 30 to 6 00 p m Eastern Standard Time For Cybex customers living in the USA contact Cybex Customer Service at 888 462 9239 For Cybex customers living outside the USA contact Cybex Customer Service at 508 533 4300 or fax 508 533 5183 Find information on the web at www cybexintl com by e mail at techhelp cybexintl com Ordering Parts Fax order to 508 533 5183 To speak with a customer service representative call 888 462 9239 for customers living within the USA or 508 533 4300 for customers outside the USA You may also contact us through e mail at techhelp cybexintl com Having the following information ready when calling will assist our Cybex representatives in serving you e Unit Serial Number e Product Name The unit serial number and product name can be found on the serial number decal See Chapter 6 for exact location of serial number decal Part Description Part Number Part descriptions and part numbers are located in Chapter 6 of this manual e Shipping Address e Contact Name Return Material Authorization RMA In addition to your shipping address
25. orm regular maintenance checks on the equipment Also pay close attention to all areas most susceptible to wear including but not limited to cables pulleys belts and grips Immediately replace worn or damaged components If unable to immediately replace worn or damaged components then remove from service until the repair is made e Use only Cybex supplied components to maintain repair the equipment Keep a repair log of all maintenance activities Inspect all cables and belts and connections prior to use DO NOT use if any components are worn frayed or damaged NOTE It is the sole responsibility of the user owner or facility operator to ensure that regular maintenance is performed Safety Guidelines And Practices Cybex recommends that all fitness equipment be used in a supervised area It is recommended that the equipment be located in an access controlled area Control is the responsibility of the owner The extent of control is at the discretion of the owner It is the responsibility of the purchaser user of Cybex products to read and understand the owner s manual and warning labels as well as instruct all individuals whether end users or supervising personnel on proper usage of the equipment PROPER USAGE Use machine only as described in the manual Failing to follow proper instructions may result in injury Do Not Lean Against or Pull On the framework weight stack or any component whether machine is at rest or in u
26. pment Chrome Clean chrome tubes first using chrome polish and then using a car wax seal Neutral cleaners with a pH between 5 5 and 8 5 are recommended Be sure to dry thoroughly AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the equipment Cybex Eagle 11050 Leg Extension Owner s Manual 4 Guidelines for cleaning front panel e Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing Follow up the application with warm water rinse Don t use abrasives or high alkaline cleaners Don t leave cleaners for long periods wash immediately Don t apply cleaners in direct sunlight or at elevated temperatures e Don t use scrapers Squeegees or razors e Don t clean with gasoline Compatible Cleaners and Detergents e Formula 9 Top Job e Joy e Palmolive Windex with Ammonia To Minimize Fine or Hairline Scratches Mild automotive polish applied and removed with a soft clean cloth will help fill scratches Suggested Polishes e Johnson Paste Wax e Mirror Glaze 10 Plastic Polish by Mirror Bright Polish e Novus Plastics Polish 1 2 by Novus Inc Maintenance Page 5 3 Cybex Eagle 11050 Leg Extension Owner s Manual Weekly Procedures 1 Check all nuts and bolts for looseness Tighten as required 2 Inspect all belts entire length for any non uniformity and w
27. se Inappropriate or improper use may result in injury to users or third parties bystanders Do not use machine if it is not located on a solid level surface or is improperly installed Provide an adequate safety perimeter between the machine walls and other equipment to ensure that the facility has the proper clearance for usage and training SECURING EQUIPMENT The machine has holes in the feet which allow for ease in anchoring to the floor Cybex strongly recommends that to eliminate rocking tipping or falling over due to incorrect usage and misuse equipment be secured to a solid level surface 1 The solid level surface should not deviate more than 1 8 over a 10 distance or as defined and required by local building and architectural codes 2 Anchoring of equipment must be completed by a qualified licensed contractor Safety Page 1 2 Cybex Eagle 11050 Leg Extension Owner s Manual 3 Anchoring holes are provided on the feet of the frame All anchoring locations must be used when anchoring the equipment to the floor 4 Due to the wide variation of flooring on which machines may be anchored or installed verify anchoring method and anchoring fasteners with a qualified and licensed contractor 5 Aminimum pull out force of 220 165 100 kgs is required for each anchor position 6 Do not use machine until it is properly anchored MAINTENANCE Preventative maintenance allows proper equipment operation and reduces the
28. snap links for proper latching indicates wear Replace all worn snap links immediately Inspect for loose or worn grips Replace all loose or worn grips immediately Inspect all labeling for readability This includes instructional placards warning and caution decals Replace all worn labeling immediately Inspect all weight stacks for proper alignment and operation Correct all improper alignment and operation issues immediately Wipe Weight Stack Guide Rods clean over entire length Lubricate with a light coat of medium weight automotive engine oil Yearly Procedures Replace all belts and cables at least annually Cybex Eagle 11050 Leg Extension Owner s Manual Environment Static Electricity Depending upon where you live you may experience dry air causing a common experience of static electricity This may be especially true in the winter time You may notice a static build up just by walking across a carpet and then touching a metal object The same can hold true while working out on your unit You may experience a shock due to the build up of static electricity on your body and the discharge path of the unit If you experience this type of situation you may want to increase the humidity to a comfortable level through the use of a humidifier Humidity The unit is designed to function normally in an environment with a relative humidity range of 30 to 75 NOTE Do not install or use the unit in an area
29. th the part s 5 Forward the package through UPS to Cybex Attn Customer Service Department Cybex International Inc 1975 24th Ave SW Owatonna MN 55060 NOTE Merchandise returned without an RMA number on the outside of the package or shipments sent COD will not be accepted by the Cybex receiving department Damaged Parts Materials damaged in shipment should not be returned for credit Shipping damages are the responsibility of the carrier UPS Federal Express trucking companies etc Apparent Damage Upon receipt of your shipment check all items carefully Any damage seen with a visual check must be noted on the freight bill and signed by the carrier s agent Failure to do so will result in the carriers refusal to honor your damage claim The carrier will provide you with the required forms for filing such claims Concealed Damage Damage not seen with a visual check upon receipt of a shipment but notices later must be reported to the carrier as soon as possible Upon discovery of the damage a written or phone request to the carrier asking them to perform an inspection of the materials must be made within ten days of the delivery date Keep all shipping containers and packing materials as they will be needed in the inspection process The carrier will provide you with an inspection report and the necessary forms for filing a concealed damage claim Concealed damage claim is the carrier s responsibility Customer Servi
Download Pdf Manuals
Related Search