SERVICE MANUAL FOR MODEL WPP-531-FD
Contents
1. PROPRIETARY 8 0 SPECIFICATIONS INPUT POWER LOOP CURRENT IMPEDANCE SIGNALING OUTPUT ENVIRONMENTAL PROGRAMMING MEMORY RETENTION DIMENSIONS SSP MOUNTING WEIGHT WEATHERPROOF HOUSING DIMENSIONS WPP MOUNTING WEIGHT FCC REGISTRATION RINGER EQUIVALENCY TYPE JACK UL LISTED NO ISSUE 4 0 C O LINE POWERED 48v 52v Loop 30ma MIN 80ma MAX 600 Ohms DTME 70ms tone 50ms spacing 4 0 to 6 0dbm Temperature 0 C to 50 C Humidity 20 90 non condensating Via DTMF keypad Non volatile storage does not require power 7 1 6 Wide x 11 1 4 High x 4 1 4 Deep Handset on hook Vertical Surface Mount Approximately 4 Pounds Cast Aluminum 9 Y2 Wide x 12 5 8 High x 8 deep including door 4 holes spaced 8 x 5 7 8 x 13 32 or optional pole mounting bracket Approximately 12 pounds BW88T7 13716 TE T 0 4A RJ11C 6OF5 CEECO 16 Communication Equipment amp Engineering Company PROPRIETARY 9 0 PARTS LIST QUANTITY PART NUMBER ISSUE 4 0 DESCRIPTION 4 331 006 Outer Cover Locking Screw l 301 018 Modular Line Cord 301 054 Modular Connector RJ11C l 531 200 Service Manual l 700 008 Keypad Cable 660 000 CEECO SPK Board l 705 110 Connectorized Keypad 2 6020 Momentary Panel Switch l 14123 Speaker l 331 005 Weatherproof Housing l 12017 Ringer ACCESSORIES l 301 064 Security Tool CEECO 17 Communication Equipme2. 7 1 Always 1 for this model Digit 8 O Do not dial PBX access number 18 Default 1 Dial PBX access number stored in Location 18 For Call Button Digit 9 O Do not dial PBX access number 02 Default 1 Dial PBX number stored in location 02 For Emergency Button Digit 10 O No Wink Detect 1 9 Length of the Wink 1 50ms incremental to 450ms entering a 5 is recommended CEECO 7 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 PROGRAMMING CONTINUED 18 EXAMPLE DIAL 00 0152000015 Phone will be set as follows DIGIT 1 CALL RESTRICTIONS IN EFFECT DIGIT 2 INCOMING CALLS ALLOWED DIGIT 3 5 MINUTE TIME OUT FOR EMERGENCY CALLS DIGIT 4 2 MINUTE TIME OUT FOR BLACK CALL BUTTON DIGIT 5 ALWAYS 0 DIGIT 6 ALWAYS 0 DIGIT 7 ALWAYS 0 DIGIT 8 DO NOT DIAL PBX NUMBER STORED IN LOCATION DIGIT 9 DIAL THE PBX ACCESS NUMBER FIRST FROM LOCATION 02 SHORT PAUSE THEN DIAL EMERGENCY NUMBER DIGIT 10 250MS WINK LOCATION 01 EMERGENCY NUMBER RED BUTTON This location holds the Emergency number to be dialed Enter 01 followed by the desired emergency number The number can be in the range of to 11 digits Whenever a caller pushes the EMER RED button the number in location 01 will be dialed If caller wants to hang up then he or she must push the CALL button The automatic time out disconnect features will begin to work after the number has been dialed The
3. and handset the telephone has a Press to start Press to stop button for initiation and termination of phone calls The Emergency Auto Dial button is also provided for one button dialing of a preprogrammed emergency number of up to 11 digits Manual volume control is also provided inside the telephone The microphone is muted during periods of dial tone to deter the use of hand held dialers Incoming calls may be allowed or blocked depending on the programming Programming is accomplished via the DTME keypad CEECO 5 Communication Equipment amp Engineering Company PROPRIETARY 3 0 ISSUE 4 0 PROGRAMMING NOTE It is recommended that you ground yourself to prevent ESD 3 1 3 2 3 3 3 4 3 5 3 6 damage to the PCB s Connect the phone to a working telephone line or a DTMF test set to begin programming Move the mini jumpers located on the CEECO SPK Printed Circuit Board to the ON position as depicted on the last page of this manual Press the CALL button and wait for dial tone before programming any digits Each location is accessed by dialing the sign and a two digit code The valid program locations are 00 01 02 18 30 69 speed dial locations and 70 89 allowed call locations The previous contents of the location are automatically erased when the location code is accessed NOTE Once the pound key has been entered you may get an operator recording or a fast busy ple
4. call will also disconnect when the called end hangs up provided the PBX gives the proper wink back on the line Be sure to record your number above for future reference LOCATION 02 PBX EMERGENCY NUMBER RED BUTTON This location holds any PBX number to be dialed for Emergency Calls If this 1s desired enter 02 followed by the desired PBX number The number can be from to 11 digits Any number stored in location 02 will automatically dial first followed by a pause and then the phone will automatically dial the number stored in location 01 Be sure to record you number above for future reference CEECO 8 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 PROGRAMMING CONTINUED LOCATION 18 PBX BLACK CALL BUTTON This location holds any PBX number to be dialed for normal Calls If this is desired enter 18 followed by the desired PBX number The number can be from 1 to 11 digits Any number stored in location 18 will automatically dial when the black call button is pressed The keypad is then available for use Be sure to record your number above for future reference If the 18 Location is not utilized the phone will simply deliver dial tone and an enabled keypad when the Black Call button is pushed LOCATION 30 69 SPEED DIAL LOCATIONS If Speed Dialing is desired enter any of the Speed Dial Locations 30 69 followed by the desired speed dial number for that location The
5. WPP 531 FD OR SSP 511 FD SPK1 07UNVLr1 ISSUE4 0 SERVICE MANUAL FOR MODEL WPP 531 FD HANDS FREE WEATHERPROOF TELEPHONE AND MODEL SSP 511 FD STAINLESS STEEL PANEL TELEPHONE EQUIPPED WITH SPK1 07 UNVLr1 FIRMWARE B CEECO Serving the Telephone Industry Since 1930 Communication Eguipment 519 W South Park Street amp Engineering Company Okeechobee FL 34972 Voice 863 357 0798 Fax 863 357 0006 ISSUE 4 0 IMPORTANT INFORMATION FOR CUSTOMER Please fill in before you continue The following information is necessary when calling CEECO for assistance MODEL NUMBER MODEL WPP 531 FD OR SSP 511 FD EQUIPPED WITH SPK1 07UNVLrl SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you please have this information available when calling for technical support CEECO Communication Equipment amp Engineering Company 519 W South Park Street Okeechobee FL 34972 863 357 0798 telephone 863 357 0006 facsimile info ceeco net www ceeco net CEECO 2 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 TABLE OF CONTENTS SECTION PAGE 10 INTRODUCTION OE EE ceases 5 D gt EENER ES die ee teo 5 30 II 6 PROGRAMMING CONTINUED eeuse sees ee ee ee ee 7 PROGRAMMING CONTINUED iese sesse ee ee ee ee 8 PROGRAMMING CONTINUED cscssssscsssccssscscscssecsssccseccssesscecssscssscsssesscesseeesees 9 PROGRAMMING CONTINUED cscssssscssscssscssscsssccssecssscssecssscssces
6. ase disregard and continue programming It is important to be slow and deliberate when pressing the keys during programming A missed or partial tone could result in improper programming Utilizing the keypad enter 97 18 This will clear all user programmable memory to begin programming Enter 00 Location 00 is the telephone options location It is comprised of ten digits all of which must be filled to render the phone functional By entering 0 through 9 into each of the 10 digits the phone is customized to a particular installation The 10 Digits and corresponding options are located on the following page Review your options and then make the appropriate entries on the keypad one right after the other Be sure to record your entries in the Location 00 Option Table for future reference CEECO 6 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 PROGRAMMING CONTINUED LOCATION 00 OPTION TABLE 00 0 0 Digi 1 2 3 4 5 6 l 7 8 9 10 Digit 1 0 Call restrictions are in effect Default 1 No call restrictions Digit 2 O No incoming calls allowed Default 1 Incoming calls allowed Digit 3 O No Conversation Time Out Default For Emergency Button 1 9 Minutes Conversation Time Out Digit 4 O No Conversation Time Out Default For Call Button 1 9 Minutes Conversation Time Out Digit 5 O Always 0 for this model Default Digit 6 O Always 0 for this model Digit
7. be or carbon station protector is recommended The station ground should not exceed 50 ohms Plug the modular line cord from the PC board into the RJ11C terminal block Dress the line cord away from the locking screws and seat the telephone assembly into the housing or mounting Secure the telephone assembly by inserting and tightening the security screws A Never install telephone wiring during a lightning storm B Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations C Never touch uninsultated telephone wires or terminals unless the telephone line has been disconnected at the network interface D Use caution when installing or modifying telephone lines OVER VOLTAGE PROTECTION DIAGRAM CEECO 13 Communication Equipment amp Engineering Company PROPRIETARY FUSE 0 29 AMP ISSUE 4 0 ON oe LI SA k 90 Y PHONE NA O LJ OTA OR x c 2 O Le hwy NO FIN S CONFIDEN VY OF LEEG TIA A CEECO Communication Equipment amp Engineering Company PROPRIETARY ANY PURPOSE OR WHICH VA V Ka 14 7 0 ISSUE 4 0 TESTING Assuming that the phone was programmed to automatically dial an emergency number and also allow use of the keypad for normal calls without automatically dialing a number when the bla
8. ck CALL button is pressed the following should apply Action With the phone connected to a working phone line Press the black CALL button Reaction The LED lights red and dial tone is received Any number programmed in the 18 Location will automatically dial out Otherwise the phone will allow normal calls to be made with the keypad Remember that if call restrictions are set the phone will only allow those calls to be made that have been programmed into the 70 89 Locations Action Dial a number Reaction The called party answers A normal speakerphone conversation is allowed Action Finish the conversation Press the CALL button or wait until time out occurs if programmed as such The LED goes out Reaction The call 1s terminated Action Press the EMER button The LED lights red Reaction The preprogrammed number is automatically dialed SEE SECTION 2 LOCATION 01 and will not disconnect unless the black CALL button is pushed the called party hangs up and a wink back is received or a programmed time out disconnect occurs at which time the LED goes out NOTE If you experienced any trouble during the testing phase please refer back to the appropriate section s of the manual Remember that the mini jumpers must be moved to ON for programming and to OFF for operation If trouble persists refer to section 11 2 please CEECO 15 Communication Equipment amp Engineering Company
9. erial only PRINTED CIRCUIT BOARDS Printed circuit boards should not be repaired in the field If a unit is found to be faulty replace it with another unit and return the faulty unit to CEECO for repair Modifications by any one other than CEECO will void the warranty CEECO 20 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 13 0 DIAGRAM Locate the mini jumpers on the corner of the PCB Move the mini jumpers to the ON position BEFORE ON going off hook When programming is completed move the mini jumpers to the OFF position NOTE Do not leave the mini jumpers in the ON position this will decrease battery life CEECO 21 Communication Equipment amp Engineering Company PROPRIETARY
10. es not press the CALL button when he or she is finished using the phone the phone will hang up after detecting a WINK momentary open or when the timer times out if it was so programmed If digit 1 of Location 00 is 0 then call restrictions are in effect The numbers that may be dialed are restricted to the numbers entered into Location 70 89 If the number dialed is not in the Location 70 89 then the phone gives three tones and drops the line If digit 1 of Location 00 1s 1 then there are no restrictions and any number may be dialed RECOMMENDED TOOLS AND TEST EQUIPMENT DTMF Test Set Volt Ohm Meter 3 8 Nut Driver 5 16 Nut Driver Flat Blade Screw Driver Security Tool CEECO Part Number 301 064 CEECO 12 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 6 0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 6 1 6 2 6 3 6 4 6 5 6 6 6 7 6 8 6 9 Using a 301 064 security tool sold separately to remove the four locking screws The security tool is for a standard 5 32 button head screw generally used on the framework of the phone booths Separate the telephone assembly from its housing or mounting Run the inside station wire through the housing or mounting and terminate on to the RJ11C modular jack inside as depicted in the diagram on the following page The CEECO provided jack must be used as it contains required over voltage protection The use of a gas tu
11. nt amp Engineering Company PROPRIETARY ISSUE 4 0 10 0 FCC NOTICE 10 1 10 2 10 3 FCC REGISTRATION AND REPAIR INFORMATION Your new telephone has been registered with the Federal Communication Commission FCC in accordance with Part 68 of its rules The FCC requires that you be advised of certain requirements involving the use of this telephone CONNECTION WITH THE NATIONWIDE TELEPHONE NETWORK The FCC requires that you connect this telephone to the Nationwide Telephone Network through a registered jack provided by the Telephone Company in your area This jack is a modular outlet which you can order from your local telephone company NOTIFICATION TO THE TELEPHONE COMPANY Before connecting this telephone the FCC requires that you notify your local telephone company business office The number is in the front of your phone book Tell them The line to which you will connect the telephone that is your phone number and the telephone s FCC registration number and ringer equivalence number These numbers are listed in Section 11 00 The FCC further requires that you notify your local telephone company when permanently disconnecting this telephone CEECO 18 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 11 0 REPAIR AND RETURN INFORMATION 11 1 11 3 WARRANTY REPAIR Any device returned requiring warranty service repair or credit must be accompanied with a Return Material Autho
12. re are 40 locations to choose from and use The numbers to be speed dialed can range from 1 to 11 digits EXAMPLE Enter 3018005551212 in the programming sequence When in normal operating mode the user dials 30 and the phone will Speed Dial 1 800 555 1212 This is true for all of the Speed Dial Locations from 30 to 69 e Be sure to record your entries in the Speed Dial Table on the next page for future reference CEECO 9 Communication Equipment amp Engineering Company PROPRIETARY PROGRAMMING CONTINUED SPEED DIAL TABLE LOCATION DESCRIPTION 30 50 HS 62 os 63 64 os HOS v o o 66 _ 67 H68 609 ISSUE 4 0 LOCATION DESCRIPTION Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 PROGRAMMING CONTINUED LOCATION 70 89 CALL RESTRICTIONS ALLOWED CALLS If the phone is intended to restrict certain calling patterns then it must be programmed to tell it specifically which calls to allow Enter the allowed numbers in any of these 20 locations The numbers can range from 1 to 11 digits Enter the key followed by a two digit location code 70 89 followed by the allowed calling pattern The Asterisk symbol is defined as a wildcard A wildcard allows any digit 0 9 to be dialed in its place Be sure to record your entries in the table below for future reference EXAMPLE PIO ENE ee ane Allows all 0 minus and 0 plu
13. rization RMA FORM It must include return shipping instructions original purchase order number and special marking instruction A description of the trouble observed must be attached to the defective unit This information must be inside the shipping container DIRECT ALL INQUIRES TO CEECO Repair Department 863 357 0798 telephone 863 357 0006 facsimile info ceeco net www ceeco net NON WARRANTY REPAIR CEECO will repair equipment out of warranty for a set charge plus parts The customer must pay the shipping costs both directions RETURN FOR CREDIT Material may be returned for credit only with prior approval Material authorized for return is subject to a 20 restocking charge based on the manufacturer s list price Return RMA must be requested no later than 30 days after original shipment CEECO 19 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 12 0 WARRANTY POLICY 12 1 12 2 GENERAL CEECO products are guaranteed to be free of defects in material and workmanship for a period of 365 days from the date of original purchase CEECO s obligation under this warranty is limited to repair or replacement of any part found to be defective by CEECO Under no circumstances shall CEECO be liable for loss damage cost of repair or consequential damages of any kind which have been caused by neglect abuse act of God or improper operation of equipment This warranty 1s limited to the value of mat
14. s calls 7115551212 Allows 1 555 1212 information calls 72911 Allows 911 emergency calls 731800 5 x ee Allows 1 800 calls RESTRICTION ALLOWED CALL TABLE LOCATION DESCRIPTION LOCATION DESCRIPTION HTO LL id O VEN SEE HI NE EN EN EE me N A T2 o o EE EEN ie NE AN TERA WEN zal OE NE GEE NM TER A A FIA di E A GENE 75 o o N EN PREN 76 EE o ST sa zal WEE HIT o o N EEN oe EN EE EED 78 oo o EN EEN os OS BA HTI9 2 od AE E E CEECO 11 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 PROGRAMMING CONTINUED 4 0 5 0 3 7 When programming is finished return the mini jumpers to the OFF position Then return the phone to an on hook state no dial tone by pressing the black CALL button OPERATION 4 1 4 2 4 3 4 4 To make a call press the black CALL button located on the front of the phone The LED will light red at this time When dial tone is received the transmitter 1s muted and the phone waits for numbers to be dialed Any programmed PBX number 18 Location will automatically dial out To make an Emergency call press the red EMER button located on the front of the phone The LED will light red at this time The preprogrammed number will dial out on the line Any programmed PBX number 02 Location will automatically dial out first After the call is complete press the CALL button again to terminate the call The LED will go out If user do
15. ssecssecsseesseesee 10 PROGRAMMING CONTINUED cscssssscssscssscsssccssccssecssecssecssscssccsssesssessseesseeses 11 PROGRAMMING CONTINUED cscssssscssscssscsssccssecscecssscssscssscsssesscesssecsseenseeses 12 40 OPERATION see ee ee ee ee ee ee ee 12 50 RECOMMENDED TOOLS AND TEST EQUIPMENT cccccssscsssccesccsecssseceese 12 6 0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS nn 13 TO TESMINC ii O i nesta RE VA NE O east 15 0 SPECIFICATIONS Srl 16 A O A A OO a MT 17 100 ECONO Css 18 11 0 REPAIR AND RETURN INFORMATION sesse ese esse sees ese ee ee 19 12 0 WARRANTY POLICY i e ee ee ee ee ee ee 20 ENE DACRAM OO tios 21 CEECO 3 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 CEECO 4 Communication Equipment amp Engineering Company PROPRIETARY 1 0 2 0 ISSUE 4 0 INTRODUCTION The practices in this manual provide installation and maintenance information for the CEECO Model WPP 531 FD or Model SSP 511 FD Telephone with SPK1 07UNVLrl firmware The information in this manual is subject to change without notification For information not included in this manual please call or write CEECO Customer Service 519 W South Park Street Okeechobee FL 34972 863 357 0798 telephone 863 357 0006 facsimile info ceeco net www ceeco net GENERAL 2 1 2 2 2 3 2 4 The CEECO hands free telephone is a sturdy vandal resistant Stainless Steel Panel Speakerphone Instead of a hookswitch
Download Pdf Manuals
Related Search