CAUTION GENUINE PARTS INSTALLATION INSTRUCTIONS
Contents
1. 3 white clips and fold back into foot well Fig 6 NOTE Repeat on opposite side of vehicle Page 5 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue 7 Rear Kicking Plate Outer LH Removal a Start at Rear Edge and pull up by hand May need to use tool to pry up end Fig 7 b There are 2 clips that secure the part NOTE Repeat on opposite side of vehicle 8 Remove Instrument Panel Side Mask RH a Pull the Instrument Panel Side Mask toward the door opening to release Fig 8 9 Remove Glove Box Assembly a Remove the 7 phillips screws A All screws inside glove box 3 across top 1 LH and RH bottom and 2 deep inside b Starting at top right side pull toward the seat There are 7 clips that secure the part Fig 9 c Disengage lamp harness connector and then remove the glove box assembly Page 06 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue 10 Remove the BCM from the dash assembly a Remove the 4 phillips screws securing the BCM bracket to the dash assembly Fig 10 b Rotate BCM so wiring connectors are visible Phillips Screws NOTE BCM located behind Glove Box assembly visible Phillips Screws CAUTION e Color s given in illustration s are for reference only Use location s where color deviates e If a vehicle wire is being used by another accessory and a posi Tap is present tap the accessory wire NOT the vehicle wire 112. text is illuminated with either Front door in the opened position REINSTALLATION OF REMOVED PARTS 1 All removed vehicle parts have been reinstalled 2 Clean interior of vehicle L_ 3 Verify all 4 kick plates are properly installed with no gaps to body A CAUTION e Use caution when re installing interior components to avoid damage scratch or breaking of mounting clips VEHICLE CHECK 1 Remove all tools from the vehicle 2 Inspect re installed interior trim parts for proper panel fit 3 Turn ignition to ON position 4 Reset radio presets to the recorded setting _ 5 Confirm proper radio operation 6 Initialize sun roof and power window operation 7 Turn ignition to OFF position 8 Check and clear trouble codes CAUTION e During restoring please use caution as not to cause the stacking of the vehicle harness or damage any parts Page 16 of 16 999G6 GX010 II REV 11 01 2013
3. GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION Illuminated Kick Plate APPLICATION Rogue 2011 PART NUMBER 999G6 GxX010 KIT CONTENTS mem orv Descripton Service Part Number 999G6 GCO01 99966 GX000 99966 GX003 ei iat RRR E E Te i _WireHamess Notaservicepat Te o oira OO Notaservice pat Ce s ewa O O Notaservicepat 6 Urethane Foam Tape Nota service pat xxx Components E thru H in are located in Harness Bag T e A gt ROGUE ROGUE lt TOOLS REQUIRED e Nylon Removal Tool e Flash Light e 100 alcohol e Phillips Head Screw Driver e Soft cloth e Soap water PRE INSTALLATION CAUTION NOTES e Dealer installation recommended Instructions may refer to Service Manual e This part is to be installed at a surface temperature no warmer than 65 100F Ay CAUTION e This accessory must only be installed as specified in these instructions e Ensure at all times that parts are securely fitted and will not compromise the safe function of vehicle systems Page 1 of 16 999G6 GX010 II REV 11 01 2013 INSTALLATION OVERVIEW Plate Kicking FR RH Plate Kicking RR RH j Plate Kicking FR LH Plate Kicking RR LH CRITICAL STEPS e Locate LH mark on back side of part for LH side install
4. Tap the Red wire of the Kick Plate Harness to the Dark Green wire located in cavity 57 Of the M67 connector at the BCM Fig 11 a See steps 12 16 for Posi Tap installation instructions f park Green q Yellow Cavity View Green larger dia Page 07 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue i Straight and evenly spaced all the way around ii Tight and minimize gap wire jacket should be crushed Fig 14 e Insert wire to here c a a gt Tighten i Straight and evenly spaced all around li Tight and no gap iii Test the signal P e o ot FSF k ay ath gr p Accessory Existing harness harness E O O ammm 12 Tap Vehicle Wire Fig 12 a Remove cap slot side from tap body b Slide cap around vehicle wire c Tighten the tap TIGHT with finger pressure NOTE Do not re use the tap for subsequent re installation 3 13 Inspect the tap to ensure correct installation Fig 13 NOTE Avoid putting pressure on the vehicle wire and tap for the rest of the installation 14 Tap accessory wire Fig 14 a Remove tap non pierce side from tap b Remove protective stub from black wire c Insert the black wire through the non pierce side opening d Spread individual strands into a fan shape e Insert wire into the tap body and ensure that it is all the way in f Tighten the tap TIGHT with finger pressure 15 Confirm
5. ation Locate RH mark on back side of part for RH side installation Mis installation can cause improper fit e Follow posi tap instructions Page 2 of 16 999G6 GX010 II REV 11 01 2013 VEHICLE PREPARATION Ay CAUTION Dealer Installation Recommended Instructions refer to steps described in Service Manual Please read these instructions carefully before installing this product for correct installation Please DO NOT use or install the part in ways other than what ts described in this instruction manual If problem occurs during installation please contact Nissan dealer where you purchased the product 1 Apply Park Brake 2 Make sure the shift lever is engaged in P position 3 Record customer Radio Presets Preset 1 2 3 4 5 6 4 Use seat and floor protection 5 Open hood of the vehicle 6 Disconnect the negative battery terminal to prevent short circuits during installation 7 This part is to be installed at a vehicle body surface temperature of 65 100 F CAUTION e Take care not to scratch or damage any component during the removal or re installation process e Trim pieces found to have witness marks or broken clips are not to be re installed Removal Sequence Front Kick Plate Outer LH 9 Rear Kick Plate Outer LH Front Kick Plate Outer RH 10 Rear Kick Plate Outer RH Front Kick Plate Inner LH 11 Instrument Panel Side Mask LH Front Kick Plate Inner RH 12 Glove Box Dashboard Side Lowe
6. f 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue 19 Re Install the BCM to the dash assembly a Secure Harness to BCM Cable with 4 tie wraps Fig 19 b Rotate BCM back into position c Re install 4 phillips screws Passenger Door 20 Secure Wire Harness a Secure Harness with 2 tie wraps Fig 20 Passenger Door a ad Page 10 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue 21 Route Wire Harness across vehicle to drivers side a Wire to be positioned between hard plastic and white foam pads under carpet Route wire over transmission hump Figure 22 23 24 25 b Secure Harness with 4 pieces of Foam Tape Fig 21 5 aie Foam Tape 22 Secure Wire Harness RH a Feed harness under carpet b Loosely secure Harness at connector to vehicle harness with 1 tie wrap Fig 22 c Secure wire with 2 foam tapes NOTE Do not attach to drain pipe Passenger Door 23 Secure Wire Harness a Feed harness through hole in carpet b Feed harness under center stack to driver side c Secure Harness under center stack with 1 tie wrap Fig 23 Tie Wrap Passenger Door Page 11 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue 24 Secure Wire Harness a Apply 1 piece of foam tape to left edge of Metal Bracket Fig 24 b Route wire along left side of Metal Bracket and down under carpet 25 Secure Wire Harness LH a Loosely secure Harne
7. installation of the tapped wire Fig 15 a Inspect the tap to ensure correct installation NOTE Avoid putting pressure on the vehicle wire and tap for the rest of the installation 16 Secure the tap Fig 16 a Secure the tapped wire on the non pierced side to the body of the posi tap with electrical tape 2 revolutions b Secure the body to harness where the vehicle wire is being tapped with electrical tape 2 revolutions Page 08 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue 17 Tap the Yellow wire of the Kick Plate Harness to the Beige wire for 2013 Model year vehicles and Pink wire for 2008 2012 Model year located in cavity 12 of the M65 connector at the BCM See Fig 17 a See steps 12 16 for Posi Tap installation instructions D AT f Papa F a OO ene yi oon i A x A 7 h ae i A r re gr _ x Paaa j T d _ a Note For 2008 2012 Model year vehicles the wire color in cavity 12 of the connector is Pink For 2013 Model year the wire color in cavity 12 is changed to BEIGE M i y t A IN iI VELL UL LE ATST Ei SS i i 4 1 ty 1 moa ki Li 13 1 i yi ti Lt A 4 Vie hmhe 13 Light Green 18 Tap the Black wire of the Kick Plate Harness to the White wire located in cavity 47 of the M66 connector at the BCM Fig 18 a See steps 12 16 for Posi Tap installation instructions Cavity 47 NS White Brown ANUAUANAAAAAN Cavity View Page 09 o
8. r Panel LH ee Dashboard Side Lower Panel RH Center Console Lower Panel LH Center Console Lower Panel RH CON ADU BRWN FE Page 3 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE 1 Front Kicking Plate Outer LH Removal a Start at Rear Edge and pull up by hand May need to use tool to pry up end Fig 1 b There are 4 clips that secure the part NOTE Repeat on opposite side of vehicle 2 Front Kicking Plate Inner LH Removal a Start at Rear Edge pull up and toward seat using nylon tool b Carefully lift part up moving from rear to front Fig 2 c There are 7 clips that secure the part NOTE Repeat on opposite side of vehicle 3 Weather Seal LH Removal a Start at in center of door opening and pull up b Pull seal away from the body between the b pillar lower and the side mask Fig 3 NOTE Repeat on opposite side of vehicle Page 4 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue 4 Remove Dashboard Side Lower Panel LH a Remove Black Cap by hand b Starting at the floor pull part toward the foot pedals There is 1 clip c that secures the part Fig 4 NOTE Repeat on opposite side of vehicle 5 Remove the Center Console Lower Panel LH a Pull the Center Console Lower Panel towards the foot pedals There are 4 clips that secure the part Fig 5 NOTE Repeat on opposite side of vehicle 6 Fold Back Carper LH a Pull carper off of
9. rness with 2 tie wraps Maintain a 150mm 200mm gap between tie down points Fig 29a Fig 29b d If you have excess harness loop the extra length to the vehicle harness with 1 tie wrap Fig 29b e Tighten all tie wraps f Cut excess tie wrap Excess Harness Page 14 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue The Procedure below shows the installation for LH Side Repeat Procedure for RH side Front RH amp LH parts are not interchangeable 30 Install Rear Kicking Plate Outer LH a Clean vehicle body with alcohol and allow to dry b Starting from the front align clips on the kicking plate with the body holes Fig 30 NOTE Be careful not to damage clips during installation 31 Install Rear Kicking Plate Outer LH a Place Kick Plate over holes b Cover top of the kick plate with a cloth to prevent damage c Press down directly above each clip to engage Push to snap Fig 31 NOTE Be careful to install left kicking plate to left side of vehicle Mis installation can cause improper fit Page 15 of 16 999G6 GX010 II REV 11 01 2013 CHECK BEFORE PART REINSTALLATION 1 Please check that the installation has no problem L_ a confirm connection of connectors _ b confirm wire harness attachment to the vehicle _ c confirm that there are no loose parts that would cause rattle FUNCTION CHECK 1 Re connect battery negative terminal 2 Confirm ROGUE
10. ss at connector to vehicle harness with 1 tie wraps Fig 25 b Secure wire with 2 foam tapes Foam Tape Driver Door E Tie Wrap Page 12 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue The Procedure below shows the installation for LH Side Repeat Procedure for RH side Front RH amp LH parts are not interchangeable 26 Prepare Harness Connector a Remove tape wrap from harness Fig 26 Tape Wrap 27 Install Front Kicking Plate Outer LH a Clean vehicle body with alcohol and allow to dry b Starting from the front align clips on the kicking plate with the body holes Fig 27 NOTE Be careful not to damage clips during installation 28 Install Front Kicking Plate Outer LH a Place Kick Plate over holes b Cover top of the kick plate with a cloth to prevent damage c Press down directly above each clip to engage Push to snap Fig 28 NOTE Be careful to install left kicking plate to left side of vehicle Mis installation can cause improper fit Page 13 of 16 999G6 GX010 II REV 11 01 2013 INTERIOR PROCEDURE continue Connectors Fig 29a The Procedure below shows the installation for Tie Wrap LH Side Repeat Procedure for RH side Kick Plate Controller Tie Wrap 29 Connect the Kicking Plate to the Harness a Connect the Connectors Fig 29a b Make sure that wiring passes over door flange and forward of the black plastic harness retainer Fig 29a c Secure ha
Download Pdf Manuals
Related Search