INSTALLATION INSTRUCTIONS
Contents
1. 3 mm 2 6 mm 8 mm gt 10 mm DRILL BITS Ae FRONT RIGHTUNDER COVER 6 HOLES QA40807BD 2014 American Honda Motor Co Inc All Rights Reserved All 52391 1409 27 While wearing eye protection and using an air saw cut the right under cover as shown Remove any burrs NOTE Do not damage the insulator when cutting the right under cover FRONT A Cut RIGHT UNDER COVER QA40808BD 28 Using isopropyl alcohol thoroughly clean the under side where the hole seals will attach Clean with isopropyl alcohol FRONT Ww ADHESIVE 3 HOLE SEALS BACKINGS Remove QCD0615AA 29 Remove the adhesive backing from each hole seal and attach the seal over the holes as shown 9 of 14 30 Using isopropyl alcohol thoroughly clean the body where the hole seals will attach ADHESIVE BACKINGS Remove Clean with isopropyl alcohol FRONT 7 HOLE SEALS QCD0616AA 31 Remove the adhesive backing from each hole seal and attach the seal over the holes as shown 32 Remove the spring nut from the left side sill trim LEFT SIDE SILL TRIM Discard 33 Install the spring nut removed in step 32 to the left trim SPONGE Discard SPRING NUT QCD0617AA 34 Remove and discard the sponge from the clip removed in step 8 35 Install the new sponge to the clip and attach the clip to the left trim 36 Install the left trim to the vehicle panel with one clip2. LEFT UNDER COVER LEFT UNDER COVER FRONT 6MARKS LEFT FRONT TEMPLATE QA40802BD Remove the templates 5 of 14 17 While wearing eye protection drill the twelve holes to 10 mm First drill with a 3 mm drill bit and then with a 6 mm drill bit with an 8 mm drill bit and finish with a 10 mm drill bit NOTE Do not damage the insulator when drilling the left under cover LEFT UNDER COVER 3 mm gt 6mm gt 8 mm gt 10 mm DRILL BITS 6 HOLES LEFT UNDER COVER LEFT UNDER E N COVER aa FRONT QA40803BD 6 of 14 All 52391 1409 18 While wearing eye protection and using an air saw cut the left under cover as shown Remove any burrs NOTE Do not damage the insulator when cutting the left under cover E N LEFT UNDER AIRSAW cut QA40804BD 19 Peel the insulator as shown Do not peel VIEWED FROM TOP SIDE Do not peel RIGHT UNDER COVER INSULATOR INSULATOR QA61503BB 2014 American Honda Motor Co Inc All Rights Reserved 20 Using a pushpin pierce the right under cover as shown PUSHPIN 1 0 in RIGHT UNDER COVER QA61501AB 21 While wearing eye protection drill one mark to 10 mm First drill with a 3 mm drill bit and then with a 6 mm drill bit with an 8 mm drill bit and finish with a 10 mm drill bit Remove any burrs 22 Roll up the insulator and secure it to the right under cover with one wir
3. 909AA 16 Ibf ft COVER 2 2 kgf m 16 Ibf ft Secure the left running board to the two brackets A Torque the flange bolts 22 N m 2 2 kgf m 16 Ibf ft 2 FLANGE BOLTS 8 x 20 mm 22 N m 2 2 kgf m 16 Ibf ft VEHICLE PANEL FRONT LEFT 2 FLANGE BOLTS UNDER 8 x 20 mm COVER 22 N m 2 2 kgf m QCD0910AA 16 Ibf ft 13 of 14 50 Install the left rear wheel arch protector LEFT RUNNING LEFT REAR WHEEL ARCH PROTECTOR QCD0911AA 51 Secure the left running board to the left rear wheel arch protector with two self tapping screw removed in step 4 LEFT REAR WHEEL ARCH PROTECTOR LEFT RUNNING BOARD FRONT Ww 2 SELF TAPPING SCREWS QCD0912AA 14 of 14 All 52391 1409 52 Visually check that the left running board is installed parallel to the vehicle LEFT RUNNING BOARD Y Parallel LEFT RUNNING BOARD Parallel QCD0913AA 53 Repeat steps 28 through 52 on the right side of the vehicle 54 Reinstall all removed parts 2014 American Honda Motor Co Inc All Rights Reserved
4. HONDA Accessory Application INSTALLATION RUNNING BOARDS T VERSION 1 P N 08L33 TOA 100B T Issue Date PARTS LIST 16 Flange nuts Left running board e A Left front template Right running board Ly BEN Left rear template Left trim 2 Right front template Right trim Right rear template Wire tie 4 Brackets A O 4 Brackets B 22 Hole seals 2 Sponge 40 Flange bolts 8 x 20 mm Q Te 2014 American Honda Motor Co Inc All Rights Reserved All 52391 1409 08L33 TOA 1B00 90 1 of 14 TOOL AND SUPPLIES REQUIRED Phillips screwdriver Ratchet 10 mm and 13 mm Sockets Torque wrench Drill 3 mm 6 mm 8 mm and 10 mm Drill bits Blanket Eye protection safety goggles face shield etc Utility knife Pushpin File Ruler Diagonal cutter Isopropyl alcohol Shop towel The following tools are available through the Honda Tool and Equipment Program On the iN click on Service Service Bay Tool and Equipment Program then enter the number under Search Or call 888 424 6857 Air Saw T N AT192A Plastic Trim Tool T N SILTRIMTL10 Illustration of the Running Boards Installed on the Vehicle RIGHT RUNNING BOARD QCD0501AA 2 of 14 INSTALLATION Customer Information The information in this installation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehic
5. LIPS One clip is reused and seven clips are discard FRONT LEFT SIDE SILL TRIM QCD0507AA 8 Remove the eight clips from the vehicle panel 9 Repeat steps 1 through 8 on the right side of the vehicle 10 Raise the vehicle off the ground and support it in the proper locations as described in the Service Manual FRONT y 5 CLIPS LEFT UNDER Qo0D2702DB 2 CLIPS COVER 11 Remove the left under cover 4 of 14 All 52391 1409 12 Remove the canister pipe guard 3 BOLTS CANISTER CLIP PIPE GUARD Q0D2703CB 13 Remove the right under cover FRONT A L A xc CAL N 2 BOLTS i 2 CLIPS RIGHT UNDER COVER 4 CLIPS QA10601BB 2014 American Honda Motor Co Inc All Rights Reserved 14 Align and attach the left front template and left rear 15 template to the under cover with the masking tape as shown LEFT UNDER LEFT REAR COVER TEMPLATE CROSS SECTION LEFT REAR TEMPLATE LEFT UNDER COVER LEFT UNDER MASKING TAPES FRONT LEFT FRONT TEMPLATE 4 CROSS SECTION LEFT FRONT TEMPLATE 16 LEFT UNDER COVER Align Align LEFT UNDER QA40801BD COVER 2014 American Honda Motor Co Inc All Rights Reserved All 52391 1409 Using a pushpin pierce all six marks in the templates PUSHPIN LEFT UNDER 6 MARKS LEFT REAR TEMPLATE
6. e tie Do not peel VIEWED FROM TOP SIDE INSULATOR INSULATOR Roll up DRILL FRONT OA Made in y A step 21 HOLE QA61504BB 7 e 3 mm gt 6 mm gt Z A 8 mm gt 10 mm DRILL BITS a Chik M D 3 e RIGHT UNDER COVER MARK QA61502AB All 52391 1409 7 of 14 2014 American Honda Motor Co Inc All Rights Reserved 23 8 of 14 Align and attach the right front template and right rear template to the right under cover with masking tapes RIGHT FRONT DE UNOER Hsu AIE CROSS SECTION RIGHT FRONT TEMPLATE MASKING RIGHT REAR TAPES TEMPLATE CROSS SECTION RIGHT REAR TEMPLATE RIGHT UNDER RIGHT UNDER Align COVER COVER QA40805BD All 52391 1409 24 Using a pushpin pierce six marks on the each templates PUSHPIN RIGHT UNDER RIGHT FRONT TEMPLATE RIGHT UNDER COVER RIGHT UNDER COVER Ae L FRONT RIGHT REAR 6 MARKS TEMPLATE QA40806BD 25 Remove the templates 2014 American Honda Motor Co Inc All Rights Reserved 26 While wearing eye protection drill the twelve holes to 10 mm First drill with a 3 mm drill bit and then with a 6 mm drill bit with an 8 mm drill bit and finish with a 10 mm drill bit NOTE Do not damage the insulator when drilling the right under cover RIGHT UNDER COVER DRILL 3 mm gt 6 mm gt 8 mm gt 10 mm DRILL BITS RIGHT UNDER COVER
7. le These procedures should not be attempted by do it yourselfers NOTE 1 All 52391 1409 These instructions show the left running board being installed The same procedure applies to installing the right running board Do not damage the body paint finish This kit should be installed only if the ambient air temperature is 15 C 60 F or above To allow the adhesive to cure do not wash the vehicle for 24 hours Please advise the customer Remove the self tapping screws and clip from the left front wheel arch protector LEFT FRONT WHEEL ARCH PROTECTOR FRONT 2 SELF TAPPING SCREWS QCD0502AA 2014 American Honda Motor Co Inc All Rights Reserved 2 Release the left front wheel arch protector 2 CORS LEFT FRONT WHEEL EA n 2 RETAINING TABS CLIP FRONT LEFT SIDE SILL TRIM QCD0503AA Remove the clip from the left side sill trim Remove the two self tapping screws from the left rear wheel arch protector LEFT REAR WHEEL ARCH PROTECTOR 2 SELF TAPPING SCREWS QCD0504AA 2014 American Honda Motor Co Inc All Rights Reserved 5 All 52391 1409 Release the left rear wheel arch protector CLIP LEFT REAR WHEEL ARCH PROTECTOR RETAINING TAB QCD0505AA Remove and discard the three clips from the left side sill trim LEFT SIDE SILL TRIM FRONT 3 CLIPS Discard QCD0506AA 3 of 14 7 Remove the left side sill trim 8 C
8. mm flange bolts BRACKET A VEHICLE PANEL FRONT BRACKET A 2 FLANGE BOLTS 2 FLANGE BOLTS 8 x 20 mm 8 x 20 mm Loosely secure Loosely secure QCD0905AA 12 of 14 All 52391 1409 45 With help from an assistant loosely secure the left running board to the two brackets A using four 8 x 20 mm flange bolts FRONT E LEFT RUNNING BOARD LEFT RUNNING LEFT RUNNING BOA BOARD BRACKET A BRACKET A QCD0906AA 2014 American Honda Motor Co Inc All Rights Reserved 46 Secure the two brackets B to the vehicle panel 48 Torque the flange bolts 22 N m 2 2 kgf m 16 Ibf ft 2 FLANGE BOLTS 8 x 20 mm VEHICLE 22 N m 2 2 kgf m 16 Ibf ft FANEE FRONI LEFT 2 FLANGE BOLTS UNDER 8 x 20 mm QCD0907AA COVER 22 N m 2 2 kgf m 16 Ibf ft 47 Secure the two brackets A to the vehicle panel Torque the flange bolts 22 N m 2 2 kgf m 16 Ibf ft 49 2 FLANGE BOLTS 8 x 20 mm VEHICLE 22 Nm 2 2 kgt m BRACKETA PANEL 16 Ibf ft FRONT We BRACKET A LEFT 2 FLANGE BOLTS UNDER 8 x 20 mm QCD0908AA COVER 22 N m 2 2 kgf m 16 Ibf ft 2014 American Honda Motor Co Inc All Rights Reserved All 52391 1409 Secure the two brackets A to the two brackets B Torque the flange bolts 22 N m 2 2 kgf m 16 Ibf ft SIDE VIEW BRACKET B FRONT BRACKET A VEHICLE PANEL 4 FLANGE BOLTS 4 FLANGE BOLTS 8 x 20 mm LEFT 8 x 20 mm 22 N m 2 2 kgf m UNDER 22N m QCD0
9. removed in step 3 LEFT FRONT WHEEL ARCH PROTECTOR SPRING NUT QAD2017AB LEFT SHE TRIM ae FRONT QCD0901AA 10 of 14 All 52391 1409 2014 American Honda Motor Co Inc All Rights Reserved 37 Reinstall the left front wheel arch protector 42 LEFT FRONT WHEEL ARCH PROTECTOR 2 SELF LR TAPPING FRONT SCREWS QCD0902AA 38 Secure the left trim to the vehicle panel with one self tapping screw removed in step1 39 Secure the left front wheel arch protector to the left front inner fender with one self tapping screw and clip removed in step1 40 Loosely secure the bracket A to the bracket B using the four 8 x 20 mm flange bolts and four flange nuts 43 4 FLANGE BOLTS 8x 20 mm 4 FLANGE NUTS QCD0903AA 41 Repeat the same procedure for the other bracket A and bracket B 2014 American Honda Motor Co Inc All Rights Reserved All 52391 1409 Insert the two brackets B into the holes on the left under cover as shown LEFT UNDER HOLE COVER BRACKET B FRONT WE BRACKET B VEHICLE PANEL 2 FLANGE BOLTS 8x 20 mm BRACKET B Loosely LEFT secure 2 FLANGE BOLTS UNDER QCD0904AA COVER 8 x 20 mm Loosely secure With help from an assistant place the left under cover close to the vehicle and loosely install the two brackets B to the vehicle panel using four 8 x 20 mm flange bolts 11 of 14 44 Loosely secure the two brackets A to the vehicle panel using four 8 x 20
Download Pdf Manuals
Related Search