Home

T9840 Tape Drive User`s Reference Manual

Contents

1. Loading A cartridge tape is loading None Locating The tape drive is doing a high speed None seek emory Err The IPL failed IPL the tape drive again If the problem persists contact authorized service personnel TReady A A write enabled VolSafe data cartridge is None in the process of a manual unload TReady F A write protected tape is in the process of None a manual unload TReady U A write enabled tape is in the process of None a manual unload Offline The tape drive is offline Perform offline menu operations or exit the alternating menu system with 82 19840 User s Reference Manual September 2008 Revision YA 95739 Messages TABLE 5 2 Operator Panel Display Messages Continued Display Meaning Recommended Action Online The tape drive is online None OnLn Pend The online state is pending completion of None IPL diagnostics Power Fail The power supply failed Contact authorized service personnel Reading The tape drive is reading data None Ready A The loaded cartridge tape is a VolSafe None cartridge Ready F The loaded cartridge tape is write None protected Ready H A loaded high density data cartridge is Reload with low density cartridge or write enabled by the cartridge write intentionally over write from BOT protect switch in the unlocked position Note High density data cannot be read by a T9840A B drive T9840D data can
2. 4 il gt Osun a o Comm Status UserID service iV Librany10 7 19 11 50 19840 User s Reference Manual September 2008 Revision YA 95739 CHAPTER 3 Menus The menu system provides the operator and service representative a means to determine drive configuration settings access drive utilities and display the drive firmware level at the drive operator panel The menu system consists of information or values submenus and options that appear in the display section of the operator panel see Display on page 42 You navigate through the menu system by pressing the Menu and Select switches on the operator panel see Switches on page 44 The menu system information and guidelines are provided in the following order 1 Menu Structure Overview 2 Online Menu Operation on page 53 3 Offline Menus on page 62 Menu Structure Overview The drive has two main menus m When the drive is online you will use the main menu primarily for viewing the drive configuration settings m When the drive is offline you will use the main menu primarily for changing the drive configuration settings or for performing drive operations The illustration below is a high level depiction of the common elements comprising the main menu system The left column shows the first item in the menu while the right column shows the last item in the menu system Online Port View Change
3. 2 Unload any data cartridge in the tape drive 3 Insert a cleaning cartridge in the tape drive Once loaded the activity light flashes When the activity and clean indicators turn off cleaning is complete and the tape drive unloads the cleaning cartridge Note The tape drive might immediately eject the cleaning cartridge and show the message Exp ClCart in the front panel display This indicates that the cleaning cartridge has been used its maximum number of cleaning cycles Discard the worn cleaning cartridge and insert a new cleaning cartridge into the tape drive The cleaning cartridge can be used about 100 times before you must discard it If CHK xxxx appears in the tape drive s front panel display where xxxx is the fault symptom code FSC a cleaning cartridge failure occurred Try the procedure again with a different cleaning cartridge If the problem persists contact your service representative 4 Remove the cleaning cartridge from the tape drive 95739 Revision YA Chapter 4 Operator Tasks 73 Menu System Tasks Menu System Tasks The remaining operator tasks are accomplished by using the drive menu system Some tasks can be performed from the offline menu system only Place the Drive Online To change the tape drive state from offline to online 1 Press the operator panel Menu switch until Offline appears in the display window Note If you are within a submenu press the Menu switch un
4. Elevator Folder 1 0 0 0 0 11 114 017 0 51 online Stk9840c 3590 500000002205 1 42 507 5 10 o iV Power Supply Folder 1 0 0 0 Internal Addr HL PRC Addr Bay Access State Drive Type Drive SIN Code Ver 0 1 14 0 53 online stkgs40d 3590 570001000016 1 42 707 5 10 gt Pto Folder 1 0 0 0 0 49 online 5tk9940b 479000014343 1 36 407 4 09 43 online IbmUltrium2 11110123512 67U1 amp Robot Folder 1 0 0 0 0 149 joni IbmUltriu 4111 12 7U1 SP Rovot Folder 1 0 0 0 pe onine IbmUltrium2 1110123342 67U1 di 29 fonine Stka84Dc 3590 500000013257 1425071510 15 online lbmUltrium2 1110123233 67U1 4 T T Ki J Osun comm Status UserID service Library 10 7 19 11 95739 Revision The right window pane summarizes drive data in a tabular format whether you expand or collapse the drive folder tree view You can customize how the data is displayed by sorting the rows relative to a selected column and or reordering resizing the columns Notes The HLI PRC Addr column displays the host software logical address for the drive relative to the specific host software The Access State column is online offline relative to the library drive controller and not relative to the drive menu driven online offline YA Chapter 2 Operator Controls 47 Library Controls Indicators The Code Ver column displays the drive s cur
5. OOOO IPL FromTP MakeDumpTp MakeCodeTp otot i i d Zz o O 0 Ld IPL Tp Yes Ld Dump Tp 9 Yes Ld Code Tp x nm MakeDataTp 2 o g d MIR w c ae 2 o O ia SS W u Q No ReadCustTP Ld Data Tp x n 9 Ld Cust Tp x n E LdScrtchTp Yes Ld Cust Tp 9 Yes LdScrtchTp E Uda ou a nsert Write Enabled tape y Yes nsert tape requiring MIR f using a CSL to build the MIR Menu Gelect Yes on a tape press the start switch o load a tape after inserting into the feed channel Insert known good scratch tape ds C53631 64 19840 User s Reference Manual September 2008 Revision YA e 95739 CHAPTER 4 Operator Tasks This chapter discusses operator tasks primarily for desktop and rack mounted tape drives Most of these tasks rely on the physical operator panel switches alphanumeric display and the drive menu system Note For operator tasks relating to drives within a library consult the appropriate library operator guide Power on the Drive Power off the Drive IPL the Drive Write protect Enable a Data Cartridge Load a Data Cartridge Unload a Data Cartridge Clean the Drive Place the Drive Online View Drive Configuration View Firmware Release Level Place the Drive Offline Reformat a Cartridge Build MIR Exit the Menu System You can use the Virtual Operator Pa
6. ss amp SUN microsystems StorageTek M 19840 Tape Drive User s Reference Manual Part Number 95739 Revision YA Qe Sun microsystems StorageTek T9840 Tape Drive User s Reference Manual Sun Microsystems Inc www sun com Part No 95739 September 2008 Revision YA Submit comments about this document at SLSFS Sun com Copyright 2008 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 U S A All rights reserved Sun Microsystems Inc has intellectual property rights relating to technology that is described in this document In particular and without limitation these intellectual property rights might include one or more of the U S patents listed at http www sun com patents and one or more additional patents or pending patent applications in the U S and in other countries This document and the product to which it pertains are distributed under licenses restricting their use copying distribution and decompilation No part of the product or of this document might be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the product might be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and in other countries exclusively licensed through X Open Company
7. system T tape tape drive TCP IP 95739 Revision YA In Fibre Channel technology a device that connects Fibre Channel devices together in a fabric A combination of functionally interrelated interacting mechanical and electrical elements designed to work as a coherent entity See magnetic tape A device for moving magnetic tape and controlling its movement T Transmission Control Protocol Internet Protocol Glossary 103 transmission control protocol internet protocol TCP IP V vary offline vary online VolSafe VOLSER W wrap write enabled write operation write protected 104 19840 User s Reference Manual September 2008 A set of communication protocols that support peer to peer connectivity functions for both local and wide area networks IBM To change the status of a device from online to offline When a device is offline no data set may be opened on that device IBM To restore a device to a state where it is available for use by the system IBM VolSafe volume safe is a special StorageTek feature that provides write once read many WORM technology to VolSafe designated tape cartridges VolSafe permits new data to only append the tape media while it prevents erasure or overwrite of previously written data 1 VOLume SERial Number It is usually six characters long and is both the paper label stuck on the back edge of the cartridge and in the VOLID label that is rec
8. 10 000 minimum 1x 10 18 Zero 1 VR is a trademark of Overland Storage VR technology is used to achieve T9840C and T9840D capacity 95739 Revision YA Appendix A Specifications 93 Performance Specifications 94 19840 User s Reference Manual September 2008 Revision YA e 95739 APPENDIX B Cartridge Care 9840 cartridges require care to ensure proper operation and longevity Handling Caution Tape cartridge damage or data loss Handle tape cartridges properly Follow these guidelines to handle tape cartridges properly m Never open a data cartridge or touch the tape Never carry data cartridges loosely in a container Never expose the tape or cartridges to direct sunlight or moisture Never expose a recorded data cartridge to magnetic fields Always maintain a clean operating working and storage environment Storing Always store tape cartridges in an environment with the specified range of temperature and humidity found in Tape Cartridge on page 91 When storing tape cartridges follow these recommendations m Never take data cartridges out of their protective wrapping until they are needed Always use the tear string not a sharp instrument to remove the wrapping m Store data cartridges in a dirt free environment that if possible duplicates the conditions of the data processing center m Before using data cartridges that have been in tape storage acclimate the cartridges
9. Ltd Sun Sun Microsystems the Sun logo Java StorageTek StorageTek logo L Series SL8500 PowderHorn VolSafe and Solaris are trademarks or registered trademarks of Sun Microsystems Inc in the U S and in other countries U S Government Rights Commercial use Government users are subject to the Sun Microsystems Inc standard license agreement and applicable provisions of the FAR and its supplements DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 2008 Sun Microsystems Inc 4150 Network Circle Santa Clara Californie 95054 Etats Unis Tous droits r serv s Sun Microsystems Inc a les droits de propri t intellectuels relatants a la technologie qui est d crit dans ce document En particulier et sans la limitation ces droits de propri t intellectuels peuvent inclure un ou plus des brevets am ricains num r s http www sun com patents et un ou les brevets plus suppl mentaires ou les applications de brevet en attente dans les Etats Unis et dans les autres pays Ce produit ou document est prot g par un copyright et distribu avec des licences qui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit o
10. 999 0444 FRENCH TAIWAN 886 2 25185735 THAILAND 662 344 6855 TURKEY 90 212 335 22 00 e UNITED KINGDOM 44 1276 416 520 UNITED STATES 1 800 422 8020 VENEZUELA 582 905 3800 VIETNAM 65 216 8333 WORLDWIDE HEADQUARTERS 1 650 960 1300 SU N THE NETWORK IS THE COMPUTER 2006 Sun Microsystems Inc All rights reserved Sun Sun Microsystems and the Sun logo are trademarks or registered trademarks of Sun Microsystems Inc in the United States and other countries
11. Chapter 3 Menus 55 Online Menu Operation Fibre Channel View Configuration Menu Tree T9840D Use the online view configuration menu tree as a brief guide Online Offline Press Select to toggle then press Menu to set View CFG View Configuration Press Select to enter press Menu to bypass Intf XXXXX FICON FCP View PrtA view current port attributes A xxxxxxay 24 bit address ID when port login is complete B xxxxxxay when viewing port B SFP module parameters 2G MM0300m 2G SM10 0k Hard PA x Y N Physical Address PA xx ddd PA hex decimal index only when Hard PA is yes Soft PA XX HI LO only when Hard PA is no MaxSz xxxx 2112 2048 maximum data frame size H xxxxxxxx first half 64 bit port node world wide name L xxxxxxxx second half 64 bit port node world wide name WWN Custom only when custom or dynamic WWN is set View PrtB current port B attributes same sub menus as port A Emul xxxxx STD 3590 3490E 9940A displays the active emulation mode special modes used only when directed by Engineering Tech Support Cmprss Xxx Yes Off No compression mode Full DSE x Y N data security erase mode SL Prot x Y N standard label protection mode English Espanol Francais Italiano Deutsch current language Tape Bar x Y N tape completion indication VolSafe x Y N enable VolSafe write once read many Full Code x Y N drive memory contains full code load Lib Ad
12. CodCrFaillmessage 81 CodCrFail2 message 81 CodeUpDate message 81 CodUpFaill message 81 CodUpFail2 message 81 CodUpFail3 message 81 CodUpFail4 message 81 compatibility read write 31 compliance statements FCC 19 Japanese 20 Taiwan 20 configurations cartridge scratch loader 27 library attached 28 manual load units 26 Customer Initiated Maintenance CIM 17 D damaged cartridge identification 95 data cartridge load 71 make 76 shipping 96 unload 72 DatCrFaill message 81 dimensions tape drive 87 88 display folder 50 display tape drive 42 DmpCrFaill message 81 DmpCrFail2 message 81 DmpWrFaill message 81 DmpWrFail2 message 81 document conventions blue 15 bold 15 105 initial cap 15 italic font 15 drive configurations cartridge scratch loader 27 library attached 28 manual load drive 26 interfaces 29 load unload slot 40 manual unload device 41 Operations menu 64 read write compatibility 31 DumpA gain message 82 DumpToHost message 82 E encryption description of 24 status LED 25 Exp Cl Cart message 82 F fault LED 46 FCC compliance statement 19 firmware release level determination 75 Fix Cfg Err message 82 folder display 50 properties 49 SLC 47 status 48 G glossary 97 H handling cartridges 95 l indicator activity 41 clean 41 encryption status 25 operator panel 40 power 41 service 41 user actions 79 Init xxxx message 82 interface of the drive 29 internal code license 21 I
13. IP address IP L library link loader 95739 Revision YA All or part of the physical components of an information processing system such as computers or peripheral devices T A The primary computer on a network with which other computers interact An interface between a network and host computer T A Fibre Channel Arbitrated Loop switching device that allows multiple servers and targets such as storage systems to connect at a central point A single hub configuration appears as a single loop A device that provides a visual or other indication of the existence of a defined state T The initialization procedure that causes an operating system to commence operation The operations required for setting a device to a starting state before the use of a data medium or before implementation of a process T Pertaining to a device process or channel involved in data input data output or both IBM A protocol used to route data from its source to its destination in an Internet environment IBM A four byte value that identifies a device and makes it accessible through a network The format of an IP address is a 32 bit numeric address written as four numbers separated by periods Each number can be from 0 to 255 For example 129 80 145 23 could be an IP address See internet protocol A robotic system that stores moves mounts and dismounts data cartridges that are used in data read or write op
14. Level 75 Place the Drive Offline 75 Reformat a Cartridge 76 Build MIR 77 Exit the Menu System 78 95739 Revision YA Contents 7 5 Indicators and Messages 79 Indicators 79 Messages 80 Potential Operator Recovery Scenarios 84 Translated Messages 85 A Specifications 87 Physical Specifications 87 Tape Drive Only 87 Desktop Configuration 88 Rack Mount Configuration 88 Library attached Configuration 88 Power Specifications 89 Environmental Requirements 90 Tape Drive and Power Supply 90 Tape Cartridge 91 Performance Specifications 92 Tape Drive 92 Tape Cartridge 93 B Cartridge Care 95 Handling 95 Storing 95 Identify a Damaged Cartridge 95 Cleaning 96 Shipping 96 Glossary 97 Index 105 8 19840 User s Reference Manual September 2008 Revision YA 95739 Figures FIGURE 1 1 FIGURE 1 2 FIGURE 1 3 FIGURE 1 4 FIGURE 1 5 FIGURE 1 6 FIGURE 2 1 FIGURE 2 2 FIGURE 2 3 FIGURE 2 4 FIGURE 2 5 FIGURE 2 6 FIGURE 2 7 FIGURE 2 8 FIGURE 3 1 FIGURE 3 2 FIGURE 3 3 FIGURE 4 1 T9840 Tape Drive Front Panel 23 Encryption Status LED SL8500 Library Drive Tray 25 T9840 Desktop and Rack mount Units 27 CSL Desktop and Rack mount T9840A 27 T9840 Tape Drive Library Attached Configurations 28 9840 Tape Cartridge 30 T9840 Operator Panel 40 Tape Bar 43 Virtual Operator Panel 45 SL8500 T9840 Drive Tray Rear Panel 46 SL8500 SLC Drive Folder Display 47 SL8500 SLC Drive Status Tab 48
15. MIR and reads it into drive memory invalid flag is not set The T9840C drive uses the memory resident MIR for user data pointers for read only functions During the first mount session the drive captures statistical counters from the MIR into a memory area called the Format Identity Burst FIB and continues to build it with drive activity Note The FIB is written in a special format which can also be read by T9840A B drives with the appropriate drive firmware level During the unload routine the T9840C drive writes the FIB to the high density MIR designated tape location The tape resident low density MIR remains intact and valid Notes a The T9840C drive identifies the tape cartridge as low density data format which results in the display of Ready L low density on the T9840C operator panel a The T9840C tape drive cannot cause nor correct an invalid MIR on a low density data cartridge A low density MIR can only become invalid during a mount on a T9840A B tape drive 34 19840 User s Reference Manual September 2008 Revision YA 95739 Mixed Media Management a If a low density data cartridge MIR is invalid it is not read into the T9840C drive memory and not available for user data pointer information Therefore T9840C performance for a low density data cartridge with an invalid MIR is degraded a Since a T9840C tape drive cannot correct nor rebuild a low density data cartridge invalid MIR the only options for
16. Operating 26 C 79 F 3 05 km 10 000 feet Shipping 26 C 79 F 15 2 km 50 000 feet Storing 26 C 79 F 3 05 km 10 000 feet Air Flow Requirement Operating Heat Output Drive and power supply operating 73 2 Calories hr 290 2 Btu hr 90 19840 User s Reference Manual September 2008 Revision YA 95739 Environmental Requirements Tape Cartridge TABLE A 7 lists the T9840 tape cartridge environmental requirements TABLE A 7 19840 Tape Cartridge Environmental Requirements Temperature Operating 15 to 32 C 59 to 90 F Storage up to four weeks 5 to 32 C 41 to 90 F Storage archival 18 to 26 C 65 to 79 F Shipping unrecorded 23 to 49 C 10 to 120 F Shipping recorded 4 to 40 C 40 to 104 F Relative Humidity Non condensing Operating 20 to 80 Storage up to four weeks 5 to 80 Storage archival 40 to 60 Shipping unrecorded 5 to 80 Shipping recorded 5 to 80 Wet Bulb Maximum Operating 26 C 79 F Storage nonarchive 26 C 79 F Storage archival 26 C 79 F Shipping unrecorded 26 C 79 F Shipping recorded 26 C 79 F 1 The acclimation time before use is 24 hours 2 The shipping environment must not exceed the limit of the storage environment archive or nonarchive for longer than 10 days 95739 Revision YA Appendix A Specifications 91 Performance Specifications Performance Specifications This sect
17. SL8500 SLC Drive Properties Tab 49 SL8500 SLC Drive Display Tab 50 Online Menus 54 Offline Menus Interface Menu Tree 62 Drive Operations Menu Tree 64 T9840 Data Cartridge Write Protect Switch 70 95739 Revision YA 10 T9840 User s Reference Manual September 2008 Revision YA 95739 Tables TABLE 1 1 TABLE 1 2 TABLE 2 1 TABLE 2 2 TABLE 5 1 TABLE 5 2 TABLE 5 3 TABLE 5 4 TABLE A 1 TABLE A 2 TABLE A 3 TABLE A 4 TABLE A 5 TABLE A 6 TABLE A 7 TABLE A 8 TABLE A 9 Encryption Status LED State Descriptions 26 Cartridge Read Write Compatibility 31 Operator Panel Indicators 41 Operator Panel Switches 44 Operator Panel Indicators 79 Operator Panel Display Messages 80 Selected Check Message Meanings 84 Translated Display Messages 85 T9840 Tape Drive Physical Specifications 87 T9840 Tape Drive Desktop Physical Specifications 88 T9840 Tape Drive Rack mount Physical Specifications 88 T9840 Tape Drive Weights Library attached 88 T9840 Tape Drive Power Specifications 89 T9840 Tape Drive and Power Supply Environmental Requirements 90 T9840 Tape Cartridge Environmental Requirements 91 T9840 Tape Drive Performance Specifications 92 T9840 Data Cartridge Physical and Performance Specifications 93 95739 Revision YA 11 12 19840 User s Reference Manual September 2008 Revision YA 95739 Preface This manual contains information about the StorageTek T9840A T9840B T9840C a
18. U No Prnt U N Bereit U Overtemp Caliente Overtemp Temperat Heiss Processing Procesar Traitement Processo Verarbeitn Reading Leer Lecture Lettura Lesen Ready A Listo A Pret A Pronto A Bereit A Ready F Listo F Pret F Pronto F Bereit F Ready H Listo H Pret H Pronto H Bereit H Ready L Listo L Pret L Pronto L Bereit L Ready U Listo U Pret U Pronto U Bereit U Rewinding Rebobinar Rebobinage Riavvolgi Spulen Unloading Descarga Dechargemt Scarico Entladen Writing Excritura Ecriture Scrittura Schreiben 95739 Revision YA Chapter 5 Indicators and Messages 85 Messages 86 19840 User s Reference Manual September 2008 Revision YA 95739 APPENDIX A Specifications This appendix lists the physical power and performance specifications for the T9840 tape drive plus the environmental requirements for the drive and data cartridges Physical Specifications This section lists the physical specifications for T9840 tape drives in three configurations desktop rack mount and library attached Tape Drive Only TABLE A 1 lists the T9840 tape drive physical specifications TABLE A 1 19840 Tape Drive Physical Specifications Measurement Specification Width 146 mm 5 75 in Depth 381 mm 15 in Height 82 5 mm 3 25 in 95739 Revision YA 87 Physical Specifications Desktop Configuration The T9840 desktop configuration is a single enclosed assembly TABLE A 2 T9840 Tape Drive
19. View Change Drive Drive CSL Enable Offline Disable Configuration TCP IP Operations Firmware Firmware Toggles Toggles Configuration TCP IP Drive Current Current CSL Exits menu Online Enable submenus submenus utilities firmware firmware system Offline Disable submenus release release level level no no Online View Online View Offline no no no submenus submenus Offline Offline only submenus submenus submenus Change Change 95739 Revision YA 51 Menu Structure Overview The drive is available with several data path interfaces The main menu items do have some variation based upon the particular interface and those variations are presented in later sections of this chapter Note The Port Enable Disable item does not appear as a main menu item for all drive interfaces Although the illustration menu titles contain full words the actual presentation on the display is an abbreviation because the display is limited to ten characters The Configuration TCP IP and Drive main menu items contain a as the last character in the display The signifies that a submenu is available You will use the Menu and Select switches to navigate through the menu system a Press Menu No to bypass and advance to the next menu a Press Select Yes to enter the submenus When you press the Menu switch on the operator panel the first menu provide
20. a partially valid MIR is mounted for long periods of time 95739 Revision YA with locates to different locations locate times will be inconsistent depending on whether the locate is to a record already in the rebuilt MIR or if some low speed locate is required The longer the tape cartridge is mounted and the more activity occurs the more rebuilt the memory resident MIR becomes Once the EOD is reached the MIR is complete and valid Chapter 1 Overview 37 Mixed Media Management 38 19840 User s Reference Manual September 2008 Revision YA 95739 CHAPTER 2 Operator Controls Several methods are available that enable you to determine the state of the tape drive perform operator tasks or view and alter drive configuration settings All T9840 drives have a physical operator panel You can use this panel to access the drive menu system to view drive indicators to access front panel switches and to load a tape cartridge In the rack mounted drive you should always have clear access to the panel For a library attached drive you must open the library door to access the drive operator panel Several library models provide the capability to obtain information about the drive from the library or a software application The library console for the SL8500 and SL3000 libraries is introduced in this chapter The T9840D tape drive is supported by the Virtual Operator Panel application release 1 0 12 or higher The VOP appli
21. all Maintenance Code and or replace Microcode which includes both Internal Code and Maintenance Code with Microcode that consists only of Internal Code Revision YA 95739 CHAPTER 1 Overview This chapter provides an overview of the T9840 Tape Drive family Tape Drive The T9840 Tape Drive is designed for fast access to data stored on a midpoint loading tape cartridge Four drive models are available for the enterprise and client server environments The T9840A and T9840B have a 20 GB uncompressed cartridge capacity The T9840C has a cartridge capacity of 40 GB uncompressed The encryption capable T9840D has a cartridge capacity of 75 GB uncompressed For more information about the tape cartridge see Cartridges on page 30 The drive front panel FIGURE 1 1 has a tape load unload slot and an operator panel for manual control See Chapter 2 Operator Controls for detailed information on operator panel controls and indicators The drive rear panel has connectors for power host interface library interface and maintenance not available on the T9840A An encryption status LED is present on the rear panel of the T9840D FIGURE 1 1 T9840 Tape Drive Front Panel TAPE LOAD UNLOAD SLOT N PANEL C53070 95739 Revision YA 23 Tape Drive Use of the RJ45 maintenance port on a non encrypiton drive is restricted to Sun service personnel only Note Customer attachment to the maintenan
22. increasing performance are i Migrate the data to a high density format cartridge using a copy utility with a second T9840C drive ii Rebuild the MIR with a T9840A B tape drive iii Operate with degraded performance On subsequent mounts the T9840C drive first sees the tape resident FIB identifies the tape cartridge as low density and reads the low density MIR into drive memory At dismount the T9840C updates the tape resident FIB with cumulative data including newer Statistical data from the MIR if the cartridge had been loaded into a T9840A B drive since the last mount in a T9840C drive T9840A B Tape Drives When a high density data cartridge is loaded into a T9840A B drive with appropriate level firmware the drive looks for a low density MIR at the default location but finds a Format Identity Burst FIB which identifies the cartridge as formatted in a high density Since the T9840A B drive cannot read nor write higher density data subsequent normal read write attempts will fail unless the cartridge is being reclaimed A T9840A B drive cannot update statistical data such as the mount dismount count in the FIB Therefore cumulative statistical data will not include mounts into a T9840A B drive as long as the tape cartridge is in high density format The tape cartridge could be deliberately over written in low density data format from the beginning of tape point or reformatted to low density data format by the offline Drive
23. it is written This map provides an index between user block ID s and the physical block on the tape media Once the data is written the drive accesses this map to optimize access to the user data A read to a user block ID is translated to the physical location on the tape media and the drive determines the quickest method to read the block If the block is some physical distance from the current location a calculation results in a high speed locate to the block location and is followed by a normal speed read The existence of the MIR is usually transparent to the user unless the MIR has a problem This could occur if the MIR update fails during a dismount The impact of an invalid MIR occurs in several areas Since the MIR enables high speed positioning an invalid MIR forces all operations to a slow speed mode This has no impact on a sequential read from the beginning of the tape However an operation that could use high speed locate defaults to a sequential slow speed read to the requested block which can result in a longer processing time An invalid MIR might be suspected if you observe poor performance on a specific tape cartridge The T9x40 drive also posts a 36B2 informational FSC whenever a tape cartridge with an invalid MIR is loaded The following sections describe MIR processing and some potential implications of MIR problems T9840 User s Reference Manual September 2008 Revision YA 95739 Mixed Media Management Norma
24. pressed during a write operation the drive attempts to write the remaining data before it unloads A display of UnWr xxxx meaning Unwritten Data where xxxx is a fault symptom code means that the attempt failed and some data remains unwritten to tape Note Pressing Unload a second time causes the unwritten data to be lost Before you press Unload again see UnWr xxxx on page 83 Front panel switches are color coded by drive model T9840A Yellow T9840B Purple T9840C Green T9840D Deep Purple 44 T9840 User s Reference Manual September 2008 Revision YA 95739 Virtual Operator Panel Virtual Operator Panel The Virtual Operator Panel provides a graphical user interface to the T9840D tape drive The interface contains several menus a set of indicators two small display areas and a text The Drive pane see FIGURE 2 3 Operations menu provides commands to perform actions that are similar to the physical operator panel switches The Retrieve and Configure menus provide commands to allow you to access functions that are equivalent to the online and offline drive menu system FIGURE 2 3 Virtual Operator Panel E File Drive Operations Retrieve Configure Help Drive IP 10 0 0 1 Load Tape Unload Tape Set Offline IPL Drive Force Dump 38 PM Sep 4 2008 38 PM Sep 4 2008 38 PM Sep 4 2008 38 PM Sep 4 2008 39 PM Sep 4 2008 Format Tape Empty MOnline Cle
25. related anomalies a Pressing the SL8500 drive tray PWR switch while the tray is powered does not cause an interrupt signal to the library firmware Wait at least 10 seconds before you press the PWR switch to manually power on the drive Otherwise the library s drive audit will be corrupted When the red FAULT LED comes on after power off it is safe to re push the PWR switch to reapply power to the drive tray FIGURE 2 4 SL8500 T9840 Drive Tray Rear Panel PWR Switch PWR i FAULT l ES Q LED 054096 46 19840 User s Reference Manual September 2008 Revision YA 95739 Library Controls Indicators StorageTek Library Console Although you cannot access the T9840 Tape Drive Operator Panel to view menu items you can use the StorageTek Library Console SLC local or remote to display data pertinent to the attached drives Note General guidance on using the SLC application is available within the SLC Help function click the button Drive Folder Top Level Display FIGURE 2 5 shows an overall summary of the Drive Folder The left window pane displays library folders in a tree format which you can expand or collapse FIGURE 2 5 SL8500 SLC Drive Folder Display MStreamline Library Console Tools Help System Detail Apply Refresh Library 1 0 0 0 0 Drive Folder gt CAP Folder 1 0 0 0 0 E o Y Drive Folder 1 0 0 0 0 amp
26. switch No to repeat the utilities submenu sequence 11 Press the Menu switch until Exit Drv appears in the display 95739 Revision YA Chapter 4 Operator Tasks 77 Menu System Tasks 12 Press either the Select switch to enter the main menu or the Menu switch to repeat the drive operations menu 13 Press the Menu switch until Exit Menu appears in the display 14 Press either the Select switch to exit the menu system or the Menu switch to repeat the Online Offline selection Note It is a best practice to return the drive to the online state See Place the Drive Online on page 74 Exit the Menu System To exit the menu system 1 Press the Menu switch repeatedly until Exit Menu appears in the display window Note If you are within a submenu press the Menu switch until Exit XXX appears in the display window and press the Select switch to enter the main menu 2 Press the Menu switch to determine the current drive state Offline or Online appears in the display 3 If the present state is offline press the Select switch Online appears in the display 4 Press the Menu switch repeatedly until Exit Menu appears in the display 5 Press the Select switch an or Online appears in the display 78 19840 User s Reference Manual September 2008 Revision YA 95739 CHAPTER 5 Indicators and Messages This chapter summarizes the operator panel indicator lights and display message
27. this edition for a description of changes EC000690 September 2008 YA Updated the SLC information to include the SL3000 library and replaced the drive tab images with ones that reflect the current code levels Changed the order of the operator tasks and moved the cartridge care and handling information to Appendix B Revised the menu system information to reflect the current microcode Replaced most of the menu system illustrations with a text based representation of the menu system 95739 Revision YA 4 T9840 User s Reference Manual September 2008 Revision YA 95739 Contents Revision History 3 Contents 5 Figures 9 Tables 11 Preface 13 Organization 13 Alert Messages 14 Mensajes de alerta 14 Typographical Conventions 15 Related Publications 15 Sun s External Web Site 16 Customer Initiated Maintenance 17 Notices 19 United States FCC Compliance Statement 19 Japanese Compliance Statement 20 Taiwan Warning Label Statement 20 Internal Code License Statement 21 1 Overview 23 Tape Drive 23 Encryption 24 Encryption Resources 24 95739 Revision YA Encryption Status LED 25 Configurations 26 Desktop and Rack mountable Drive Units 26 Cartridge Scratch Loader Drive Units 27 Library Attached Configurations 28 Interfaces 29 Cartridges 30 Mixed Media Management 31 Media Information Region 32 Normal MIR Processing 33 Cross Density MIR Processing 33 T9840D Tape Drive Loaded With a Lower Density C
28. to manually remove a tape cartridge from the drive when m The Unload switch action fails m Power is not available for the drive You use a screwdriver to engage the MUD and position the cartridge to be manually pulled out of the load unload slot Note Only qualified service personnel should operate the MUD 95739 Revision YA Chapter 2 Operator Controls 41 Front Panel Display The operator panel has a 10 segment alphanumeric display that indicates m Drive status Menu selections and configuration choices Error messages and fault symptom codes Host generated messages Tape bar if activated The display is formed by a horizontal array of 10 segments Each segment is formed by an array of 35 dots five wide and seven high FIGURE 2 2 on page 43 Each array can form an uppercase or lowercase alpha character a numerical digit or a special character such as an asterisk When the tape bar is not activated the lighted segments and dots form text messages The text messages may display steadily flashing or alternating with other messages Tape Bar The tape bar uses the operator panel display to show the amount of tape that has been written and read The tape bar is a configuration option that must be activated by authorized service personnel Once activated it appears on the operator panel display when the drive is reading or writing When the tape bar is activated the segments and dots simultaneously
29. 000 e oe o 0008 e n o c ce e0 0 00000 oceceo O00000 00000 10 20 30 WRITE BAR 50 UNWRITTEN AREA m mm mam a 60 70 80 90 100 o O 020 0 00006 00606060 00000 00060 00000 006060 eo 00060000 00000090 0000000 00000090 00600000 000006 000086 40 5 Oo aL 053412 95739 Revision YA Chapter 2 Operator Controls 43 Front Panel Switches TABLE 2 2 describes T9840 operator panel switch functions TABLE 2 2 Operator Panel Switches Switch Description Menu Pressing the Menu switch accesses the menu system steps through a series of submenus or answers No to a displayed question Pressing the Menu switch the first time causes the Online Offline selection to display See Chapter 3 Menus for information guidance with the menu system Select Pressing the Select switch accesses a displayed submenu steps through possible options of a submenu or answers Yes to a displayed question When the drive is Online and in a view only submenu pressing Select is the same as pressing Menu IPL Pressing the IPL switch causes the drive to execute an initial program load IPL sequence During IPL the drive firmware loads from non volatile memory in an EEPROM to RAM The same process occurs at power on Unload Pressing the Unload switch causes the tape cartridge to rewind unthread and unload ending with the tape cartridge ejected and retrievable If this switch is
30. 0A B written data cartridge has an invalid MIR its contents cannot be read into the T9840D drive s memory and the user data pointer information will be unavailable This causes a performance degradation T9840C tape Drive Loaded With a T9840D Data Cartridge The T9840C drive will not be able to read the MIR written by a T9840D drive Because it was written by a T9840D there will be no T9840A B MIR The T9840C drive will read the Format Identity Burst FIB written by the T9840D tape drive Note The T9840C drive identifies the tape cartridge as high density data format and Ready H high density appears in the T9840C operator panel display Since the T9840D written data cannot be read by the T9840C tape drive the only actions available to the drive are m Unload the data cartridge m Reclaim the data cartridge If the data cartridge is reclaimed the T9840C drive will include the statistical information from the T9840D FIB when it writes the T9840C MIR and FIB T9840C Tape Drive Loaded With a T9840A B Data Cartridge When a data cartridge is loaded into a T9840C the drive first looks for a MIR at the high density MIR designated location and will not find a MIR if the data cartridge is in low density data format The high density MIR location will be blank if it is the first time the low density data cartridge is loaded into a T9840C drive This causes the drive to look at the low density MIR designated location where it finds a
31. 2 Health State ok Drive 1 3 2 1 2 Device State Ready Drive 1 3 2 1 1 Access State online eta Drive State empty Y Drive 1 4 1 1 1 Drive needs cleaning false o Y Elevator Folder 1 0 Host Activity false o iV Power Supply Folde amp Y Pto Folder 1 0 0 0 0 gt Robot Folder 1 0 0 1 o Q Safety Door Folder 4 Ill gt Esun Comm Status UserID service Library 10 7 19 11 48 19840 User s Reference Manual September 2008 Revision YA 95739 Library Controls Indicators Properties The General block in the Properties tab FIGURE 2 7 displays some of the data from the drive folder summary plus the drive interface type not displayed in the summary The Drive Configuration block displays selected configuration items such as World Wide Name this is a dynamic value WWN that is auto set by the library relative to the drive bay number FIGURE 2 7 SL8500 SLC Drive Properties Tab Streamline Library Console Tools Help System Detail Apply Refresh Library 1 0 0 0 0 Drive gt 9 CAP Folder 1 0 0 0 Status Display 9 Drive Folder 1 0 0 0 Q Drive 1 1 1 1 4 General Drive 1 1 2 1 3 Drive Type Stk9840d 3590 Drive 1 2 1 1 2 Code Version 1 42 707 5 10 ye O Vendor StorageTek Drive 1 3 2 1 2 Serial Number 570001000016 Y Drive 1 3 2 1 1 Interface Type Ficon Drive 1 4 1 1 1 amp Elevator Folder 1 0 Drive Config
32. 3161951xx Crypto Key Management System Version 2 0 Systems Assurance Guide 316194803 Virtual Operator Panel User s Guide 96179 Most of the documentation listed in the previous table can be found online at the following URL http docs sun com app docs prod tape storagetthic 95739 Revision YA Preface 15 Publications regarding Sun Microsystems tape device software products Sun Microsystems Software Products A list of Sun Microsystems tape device software products can be found online at http docs sun com app docs prod tape devicetthic Sun s External Web Site Sun s external Web site provides marketing product event corporate and service information The external Web site is accessible to anyone with a Web browser and an Internet connection The URL for the external Web site is http www sun com The URL for StorageTek brand specific information is http www sun com storagetek 16 T9840 User s Reference Manual September 2008 Revision YA 95739 Customer Initiated Maintenance Customer initiated maintenance begins with a telephone call from you to Sun Microsystems StorageTek Support You receive immediate attention from qualified personnel who record problem information and respond with the appropriate level of support To contact Sun Microsystems StorageTek Support about a problem http www sun com storagetek support index jsp This section describes what to do if proble
33. 840 User s Reference Manual September 2008 Revision YA 95739 Interfaces Interfaces Host interfaces for the T9840 Tape Drive include m Enterprise Systems Connection ESCON single port connector m Fibre Channel FC m Fibre Connection FICON m Small computer system interface SCSI T9840A B only single port connector Note Not all interfaces are available for all configurations see TABLE A 8 on page 92 The T9x40 tape drives support connection of both ports in accordance with ANSI Fibre Channel specifications Refer to the InterNational Committee on Information Technology Standards INCITS documents m SCSI Primary Commands 3 Section 5 6 m Fibre Channel Protocol 3 Note The drive will support two hosts provided that they honor the reserve release or the persistent reserve release specifications 95739 Revision YA Chapter 1 Overview 29 Cartridges Cartridges The 9840 data cartridge shown in the figure below has the supply and takeup reels inside the cartridge which permits midpoint loading and fast access to data files FIGURE 1 6 9840 Tape Cartridge CUSTOMER MANUFACTURER LABEL LABEL AREA WRITE PROTECT SWITCH FORWARD MEDIA ID POSITION IS LABEL FINGER WRITE PROTECTED VOLSER GRIPS LABEL REAR VIEW C53069 The 9840 data cartridge has a typical capacity of m 20GB uncompressed when written by a T9840A or T9840B drive m 40 GB when written by a
34. 90 displays current emulation mode special modes used only when directed by Engineering or Tech Support Cmprss Xxx Yes Off No compression mode Full DSE x Y N data security erase mode Drv Adr xy 2 character hexidecimal logical drive address usually 00 SL Prot x Y N standard label protection mode English Espanol Francais Italiano Deutsch current language Tape Bar x Y N tape completion indication VolSafe x Y N enable VolSafe write once read many Full Code x Y N drive memory contains full code load CSL Xxxxxx Y N CSL operating mode System Auto Manual Lib Adr xy FF 00 13 2 character hexidecimal library address manufacturing setting is FF and it must be changed to a valid address when the drive is installed in a 9310 library H xxxxxxxx first half 64 bit drive node world wide name L xxxxxxxx second half 64 bit drive node world wide name WWN Custom only when custom dynamic WWN is set S N xxxxxx drive serial number last six characters of drive DMOD Exit CFG exit view configuration Press Select to exit press Menu to return to the View CFG submenu 60 19840 User s Reference Manual September 2008 Revision YA 95739 Online Menu Operation TCP IP View Configuration Menu Use the following menu tree as a brief guide to view the TCP IP settings of the T9840D tape drive Online Offline Press Select to toggle then press Menu to set View CFG Press Menu to bypas
35. A note usually but not always follows the information to which it pertains Caution A caution informs you of conditions that might result in damage to hardware corruption of data or corruption of application software A caution always precedes the information to which it pertains Warning Possible Physical Injury A warning alerts you to conditions that might result in long term health problems injury or death A warning always precedes the information to which it pertains Mensajes de alerta Los mensajes de alerta llaman la atenci n hacia informaci n de especial importancia o que tiene una relaci n espec fica con el texto principal o los gr ficos Note Una nota expone informaci n adicional que es de inter s especial Una nota puede se alar excepciones a las normas o procedimientos Por lo general aunque no siempre las notas van despu s de la informaci n a la que hacen referencia Precauci n Una precauci n informa sobre situaciones que podr an conllevar da os del hardware de los datos o del software de aplicaci n Las precauciones van siempre antes de la informaci n a la que hacen referencia Warning Possible Physical Injury Una advertencia llama la atenci n sobre condiciones que podr an conllevar problemas de salud cr nicos lesiones o muerte Las advertencias van siempre antes de la informaci n a la que hacen referencia 14 19840 User s Reference Manual S
36. Code now in your possession or use or which you hereafter acquire from either StorageTek or another party 22 T9840 User s Reference Manual September 2008 You acknowledge that copies of both Internal Code and Maintenance Code might be installed on the Equipment before shipment or included with the Equipment and other material shipped to you all for the convenience of StorageTek s service personnel or service providers licensed by StorageTek and that during the warranty period if any associated with the Equipment and during periods in which the Equipment is covered under a maintenance contract with StorageTek or service providers licensed by StorageTek both Internal Code and Maintenance Code might reside and be executed in or used in connection with such Equipment and you agree that no rights to Maintenance Code are conferred upon you by such facts StorageTek or the licensed service provider might keep Maintenance Code and service tools and manuals on your premises but they are to be used only by StorageTek s customer service personnel or those of service providers licensed by StorageTek You further agree that upon i any termination of such warranty period or maintenance contract period or ii transfer of possession of the Equipment to another party StorageTek and its authorized service providers shall have the right with respect to the affected Equipment to remove all service tools and manuals and to remove or disable
37. Desktop Physical Specifications Characteristic Manual Load Drive Chassis dimensions 230 mm 9 1 in wide 160 mm 6 5 in high 483 mm 19 in deep Cartridge Scratch Loader 483 mm 19 in wide 197 mm 7 7 in high 630 mm 24 8 in deep Weight 9 3 kg 20 5 Ib 23 kg 50 lb 1 Plus 76 mm 3 in for cables Rack Mount Configuration TABLE A 3 lists the physical specifications for the T9840 rack mount configuration TABLE A 3 T9840 Tape Drive Rack mount Physical Specifications Characteristic Value Chassis dimensions 483 mm 19 in wide 177 mm 7 0 in high 630 mm 24 8 in deep plus 76 mm 3 in for cables Weight single drive 14 1 kg 32 1b dual drive 20 4 kg 45 1b Cartridge Scratch Loader 18 kg 39 lb Library attached Configuration TABLE A 4 lists the weights of the library tape drives and accessories including trays power supplies and cables TABLE A 4 19840 Tape Drive Weights Library attached Library Drive and Accessory Weights 9310 9740 L5500 7 30 kg 16 1 1b L180 L700 L1400 7 39 kg 16 3 1b SL8500 8 85 kg 19 5 Ib The T9840 Tape Drive library attached configuration trays fit inside the m StorageTek L180 L700 L1400 libraries m StorageTek SL8500 Modular Library System m 9741 drive cabinet that attaches to StorageTek 9310 and 9740 libraries m 9741E drive cabinet that attaches to StorageTek 9310 9740 and L5500 libraries 88 19840 User s Refere
38. Drive Offline To change the drive state to offline 1 Cease all I O activity from the host In mainframe environments vary all host paths to the tape drive offline by entering one of the following commands a MVS V lt address gt offline a VM Vary off lt address gt 95739 Revision YA Chapter 4 Operator Tasks 75 Menu System Tasks ND g FP WwW N In open systems environments this is usually done by either a Stopping the job that is using that tape drive a Or in a multi host setting by making sure that any job using that tape drive has been stopped and then blocking disabling the switch port to that tape drive if there is a switch unit in use Press the operator panel Menu switch Online appears in the display window Press the operator panel Select switch to toggle the drive state Offline appears in the display window to indicate a successful transition to the offline state Press the Menu switch until Exit Menu appears in the display window Press either the Select switch to exit the menu system or the Menu switch to return to the first main menu item use the offline main menu as appropriate see Offline Menus on page 62 Note If you select Exit Menu the display alternates between Offline and the normal message after a cartridge has been loaded as a reminder that the drive is still in the offline state Reformat a Cartridge You can reformat a data cartridge for new data recordi
39. ED State Mode Description Green Safe Encryption capable but not enabled Normal unencrypted drive write read cartridge operations Red Armed Encryption enabled active Ready to encrypt Slow flashing Green Reset Encryption previously enabled but requires keys Drive is capable read only unencrypted cartridge operations Slow flashing Red Encryption read write cartridge operation in progress Amber Requires media key Slow flashing Amber Requires device key Cycling Zeroed Media device and enabling keys missing The drive is unusable and must be returned to manufacturing 1 Slow flash 1 cycle per second 2 Drive is no longer capable of unencrypted write operation once encryption has been enabled 3 The LED continuously cycles through all three colors at the slow flash rate Configurations T9840 Tape Drives are available in desktop rack mountable and library attached configurations Desktop and Rack mountable Drive Units Both the desktop and rack mount configurations shown in FIGURE 1 3 on page 27 feature manual tape cartridge loading The desktop version T9840A B only comprises a single drive and a power supply mounted within a cabinet with rubber feet The rack mount version includes a single drive or dual drives plus power supplies in a chassis tray 26 19840 User s Reference Manual September 2008 Revision YA 95739 Configurations FIGURE 1 3 T9840 Desktop and Rack mount Units Deskto
40. Fragile 96 19840 User s Reference Manual September 2008 Revision YA 95739 Glossary This glossary defines terms and abbreviations in this publication Some of the definitions are taken from other glossaries The letters in the parentheses that follow some definitions indicate the source of the definition A The American National Standard Dictionary for Information Systems ANSI X3 172 1990 copyright 1990 by the American National Standards Institute ANSI E The ANSI Electronic Industries Association EIA Standard 440 A Fiber Optic Terminology I The Information Technology Vocabulary developed by Subcommittee 1 Joint Technical Committee 1 of the International Organization for Standardization and International Electro technical Commission ISO TEC JTC1 SC1 IBM The IBM Dictionary of Computing copyright 1994 by IBM T Draft international standards committee drafts and working papers being developed by the ISO IEC JTC1 SC1 A access time The time interval between the instant at which a call for data is initialized and the instant at which the delivery of data is completed T address A character or group of characters that identifies a register a particular part of storage or some other data source or destination A alphanumeric Pertaining to data that consist of letters digits and usually other characters such as punctuation marks T A B beginning of tape BOT The location on a t
41. ITH THE TERMS OF THIS AGREEMENT DO NOT OPEN THE PACKAGE AND USE THE EQUIPMENT IF YOU DO NOT HAVE THE AUTHORITY TO BIND YOUR COMPANY DO NOT OPEN THE PACKAGE AND USE THE EQUIPMENT IF YOU HAVE ANY QUESTIONS CONTACT THE AUTHORIZED STORAGETEK DISTRIBUTOR OR RESELLER FROM WHOM YOU ACQUIRED THIS EQUIPMENT IF THE EQUIPMENT WAS OBTAINED BY YOU DIRECTLY FROM STORAGETEK CONTACT YOUR STORAGETEK REPRESENTATIVE 1 Definitions The following terms are defined as licensor s retain s ownership of all Microcode follows as well as all copies thereof that might execute a Derivative works are defined as works based in or be used in the operation or servicing of the upon one or more preexisting works such as a Equipment and that such Microcode is translation or a musical arrangement or any other copyrighted by StorageTek or its licensor s form in which a work might be recast transformed 3 or adapted A work consisting of editorial revision annotations elaboration or other modifications which as a whole represent an original work of authorship is a Derivative work StorageTek hereby grants you the end user of the Equipment a personal nontransferable except as permitted in the transfer terms below nonexclusive license to use each copy of the Internal Code or any replacement provided by StorageTek or your b Internal Code is Microcode that i is an integral authorized StorageTek distributor or reseller which part of Equip
42. Menu Tree T9840D on page 60 The basic format is a text based representation of the menu structure with indention levels to indicate second and third levels submenus There is also a listing of options and other pertinent information Note Code level 1 42 x07 was used as the basis for documenting the View Configuration menu Specific menu item order and options might differ if your drive is using an older or newer code level View TCP IP Menu The online view TCP IP menu is presented on on page 61 95739 Revision YA Chapter 3 Menus 53 Online Menu Operation FIGURE 3 1 Online Menus View ASIC I View Drive View Drive View Drive View Drive View TCP IP View Drive View CSL Exit Configuration Configuration Configuration Configuration Configuration Firmware Firmware Firmware Menu Fibre Channel SCSI ESCON FICON NA T9X40A Level l Level l Level Compress Compress Compress Interface See Note Drive Stratix and CSL Exits Menu Mode Mode Mode Selection Firmware Excaliber l id System DSEMode DSEMode DSE Mode Compress Release Level da a dd Port A and B SCSI ID Leea AE Release PRES None No CSL Attributes SCSI Target rane ode Leve Level Cee Tape Bar Negotiation ___ Logical T9840C amp D Usage Mode Stender Drive i FICON ONLY abe Address Language SCSI Protect La l Selection Speed E IS ad SCSI Limit Error Label VolSafe Width Re
43. Online Offline selection Note It is a best practice to return the drive to the online state See Place the Drive Online on page 74 Build MIR This process rebuilds an MIR from the operator panel 1 Set the drive to the offline state 2 Press the Menu switch until Drv Menu appears in the display window 3 Press the Select switch Yes once The first drive utilities submenu appears in the display window 4 Press the Menu switch until Build MIR appears in the display window 5 Press the Select switch to begin the MIR rebuilding process Ld Cust Tp appears in the display window Note Any loaded cartridge unloads at this time If present remove any unloaded cartridge 6 Inspect the cartridge for damage see Identify a Damaged Cartridge on page 95 7 Insert a write enabled cartridge with a defective MIR see Load a Data Cartridge on page 71 The drive rebuilds the MIR and ejects the data cartridge Note Rebuilding the MIR could take up to 40 minutes for a full data cartridge 8 Remove the cartridge from the drive load unload slot If there are other cartridges for MIR rebuilding repeat Step 6 and Step 7 for each cartridge When the drive has rebuilt all cartridges with defective MIRs continue with Step 9 9 Press the Menu switch once Exit Drv appears in the display window 10 Press either the Select switch Yes to exit the drive utilities submenus or the Menu
44. Operation Make Data Tape submenu Either case over writes the FIB with a low density MIR and erases the high density MIR Such a reformatted data cartridge is no longer identifiable as a high density data cartridge but does include the statistical data read from the FIB When a low density data cartridge with a tape resident FIB created by a T9840C or T9840D drive is loaded into a T9840A B drive with appropriate level firmware the MIR is read into drive memory and an invalid flag is written to the tape resident MIR During the unload routine the T9840A B drive compares statistical data in the tape resident MIR with statistical data in the tape resident FIB and uses the latest data to calculate the statistical data update into the new tape resident MIR Notes a The T9840A B drive shows Ready H on the operator panel when a cartridge written by a T9840C or T9840D drive is loaded a If the last load was into a T9840A B drive the tape resident MIR will contain the latest statistical data whereas if the last load was into a T9840C or T9840D drive the tape resident FIB contains the latest data a In order to recognize a high density data cartridge written by a T9840C or T9840D drive and to properly handle a low density data cartridge that has been previously loaded into a T9840C or T9840D drive T9840A B drives must have the appropriate drive firmware level see Mixed Media Management on page 31 95739 Revision YA Chapter 1 Over
45. PL 69 switch 44 IPL From Tp command 64 IPL Pend message 82 106 19840 User s Reference Manual September 2008 J Japanese compliance statement 20 L label media ID 30 LED activity 41 clean 41 encryption status 25 fault 46 operator panel 40 power 41 PWR 46 service 41 library attached drive description 28 license internal code 21 load a data cartridge 71 Load CC message 82 Load ESCON message 82 Load FIBRE message 82 Load FICON message 82 Load SCSI message 82 Load xxxx message 82 load unload slot 40 Loading message 82 Locating message 82 M MakeCodeTp command 64 MakeDataTp command 64 MakeDumpTP command 64 management of mixed media 31 manual containing related information 15 organization 13 manual load drive description 26 manual unload device 41 media cartridge management 31 Memory Err message 82 mensajes de alerta en el manual 14 menu operations offline 62 online 53 overview 51 structure overview 51 switch 44 messages asterisk 80 ASIA Diags 80 Bank n Bad 80 Boot Fail 80 Revision YA 95739 BT Monitor 80 CC Diags 80 Chk xxxx 80 Cleaning 80 CodCrFaill 81 CodCrFail2 81 CodeUpDate 81 CodUprFaill 81 CodUpFail2 81 CodUpFail3 81 CodUpFail4 81 DatCrFaill 81 DmpCrFaill 81 DmpCrFail2 81 DmpWrFaill 81 DmpW rFail2 81 DumpAgain 82 DumpToHost 82 Exp Cl Cart 82 Fix Cfg Err 82 Init xxxx 82 IPL Pend 82 Load CC 82 Load ESCON 82 Load FIBRE 82 Load FICON 82 Load SCSI 82 Loa
46. RE HHLBLESERRSAEMAHBBS VCCI ORE CEDC VFAZATRAREERCT COREA RERE CHAT SCRE HEA KERIO FCEPHV EFSF COBRAMOS SKDPBRKANSACCPHVETF English translation This is a Class A product based on the Technical Requirement of the Voluntary Control Council for Interference by Information Technology VCCI In a domestic environment this product may cause radio interference in which case the user may be required to take corrective actions Taiwan Warning Label Statement The following warning label statement pertains to BSMI regulations in Taiwan R O C RAC AS CLP MH RMR AEH PRA gt TRE is RATE AE MRE RAS GREER A RA English translation This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures 20 19840 User s Reference Manual September 2008 Revision YA 95739 Internal Code License Statement The following is the Internal Code License Agreement from StorageTek NOTICE INTERNAL CODE LICENSE PLEASE READ THIS NOTICE CAREFULLY BEFORE INSTALLING AND OPERATING THIS EQUIPMENT THIS NOTICE IS A LEGAL AGREEMENT BETWEEN YOU EITHER AN INDIVIDUAL OR ENTITY THE END USER AND STORAGE TECHNOLOGY CORPORATION STORAGETEK THE MANUFACTURER OF THE EQUIPMENT BY OPENING THE PACKAGE AND ACCEPTING AND USING ANY UNIT OF EQUIPMENT DESCRIBED IN THIS DOCUMENT YOU AGREE TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT IF YOU DO NOT AGREE W
47. T9840C drive PRML data format m 75 GB when written by a T9840D drive PRML data format See TABLE 1 2 on page 31 for information regarding read and write compatibility The 9840 cleaning cartridge is capable of 100 cleaning operations The media identification labels for 9840 Tape Cartridges have unique letters m R 9840 standard and VolSafe data tape cartridges m U cleaning cartridge used with T9840A T9840B and T9840C drives m Y cleaning cartridge used with the T9840D drive only A variation of the data cartridge is available for VolSafe append only use m The manufacturer and media identification labels are yellow 9840A B green 9840C or purple T9840D m The write protect switch is yellow 9840A B green 9840C or purple T9840D Model unique dimple pattern on the bottom of the cartridge case Call 1 877 STK TAPE 785 8273 to order media from the local Sun reseller or for media pre sales support To place orders electronically send an e mail to us mediaorders sun com EMEA mediaorders sun com or LA mediaorders sun com 30 19840 User s Reference Manual September 2008 Revision YA 95739 Mixed Media Management Mixed Media Management Since T9840A T9840B T9840C and T9840D drives use the same 9840 standard data cartridge you should take extra media management measures when m T9840C drives co exist in the same library system with T9840A B drives m T9840D drives co exist in the same library system wit
48. activity relative to tape movement such as reading writing or locating 2 Make sure a data cartridge is not loaded in the tape drive see Unload a Data Cartridge on page 72 as necessary 3 Set the power switch on the rear panel to off O 68 19840 User s Reference Manual September 2008 Revision YA 95739 IPL the Drive IPL the Drive To IPL initial program load a drive that is already powered on 1 Make sure the tape drive is not in use Checking for the following elements a There are no active jobs applications or programs using this drive b The operator panel activity indicator is steady and not flashing c The display window does not indicate any activity relative to tape movement such as reading writing or locating 2 Make sure a data cartridge is not loaded in the tape drive see Unload a Data Cartridge on page 72 as necessary 3 Press the operator panel IPL switch Once the IPL starts the following things happen a The drive power indicator flashes a The operator panel display window shows various messages relative to the IPL sequence These messages do not require any action from you When the drive successfully completes an IPL The drive power indicator is steady a An asterisk appears in the operator panel display window Note If there is a dump present the operator panel display window alternates between the asterisk and the dump message The dump present indication
49. an Dump amp Sun Wino Ecpt microsystems Connecting to 10 0 0 1 Tape drive is ON LINE Tape Cartridge is NOT INSERTED Connection to 10 0 0 1 Start View Drive Parameters End View Drive Parameters See the Virtual Operator Panel User s Guide P N 96179 for a full description of the application 95739 Revision YA Chapter 2 Operator Controls 45 Library Controls Indicators Library Controls Indicators When a T9840 Tape Drive is attached to the SL3000 or SL8500 Modular Library System you cannot access the drive operator panel on the front of the drive without opening the library door The drive tray rear panel does provide some indicators and an Ethernet port SL8500 T9x40 Drive Tray FIGURE 2 4 illustrates the power switch and indicators on the rear panel of the SL8500 T9x40 drive tray m The power PWR switch is a momentary push switch that manually changes the state of the internal power supply PWA m The green PWR LED indicates the power state of the tray Not lit Power is not on nor is 48 Vdc input power applied to the tray Blinking Power is not on but 48 Vdc input power is applied to the tray Steady Power is on and power supply output voltages are normal m The red FAULT LED indicates anomalies within either the internal power supply PWA or with the drive tray fan assembly Notes a Library firmware controls the drive tray power and indicators a The red FAULT LED does not indicate drive
50. ape where written data begins 95739 Revision YA 97 block buffer burst C capacity capacity raw capacity user cartridge cartridge scratch loader cc cleaning cartridge compress condition conditioning time configuration connector D data error rate data rate 98 19840 User s Reference Manual September 2008 A collection of contiguous records recorded as a unit Interblock gaps separate blocks and each block can contain one or more records A routine or storage that compensates for a difference in the rate of data flow or the time of occurrence of events when transferring data from one device to another In data communication a sequence of signals counted as one unit in accordance with a specific criterion or measure A Total amount of User Data stored on one data cartridge in 8 bit bytes Synonymous with User Capacity or Native Capacity This is the capacity that the user sees after the ECC Format ERP and other overhead has been assessed no compression Total amount of data stored on one data cartridge in 8 bit bytes before any ECC Format ERP and other overhead has been assessed no compression Total amount of data stored on one data cartridge in 8 bit bytes that is sent by the host computer This is the capacity that the user sees after the ECC Format ERP and other overhead has been assessed no compression A storage device that consists of magnetic tape on a
51. artridge 33 T9840C tape Drive Loaded With a T9840D Data Cartridge 34 T9840C Tape Drive Loaded With a T9840A B Data Cartridge 34 T9840A B Tape Drives 35 Exceptional MIR Processing 36 Invalid MIR Correction 36 2 Operator Controls 39 Front Panel 40 Load Unload Slot 40 Indicators 41 Manual Unload Device 41 Display 42 Tape Bar 42 Write Bar 42 Read Bar 42 Switches 44 Virtual Operator Panel 45 Library Controls Indicators 46 SL8500 T9x40 Drive Tray 46 StorageTek Library Console 47 Drive Folder Top Level Display 47 Drive Specific Displays 48 Status 48 6 19840 User s Reference Manual September 2008 Revision YA 95739 Properties 49 Display 50 3 Menus 51 Menu Structure Overview 51 Online Menu Operation 53 View Configuration Menu 53 View TCP IP Menu 53 Fibre Channel View Configuration Menu Tree T9840A B C 55 Fibre Channel View Configuration Menu Tree T9840D 56 SCSI View Configuration Menu Tree 57 ESCON View Configuration Menu Tree 58 FICON View Configuration Menu Tree T9840B C 59 FICON View Configuration Menu Tree T9840D 60 TCP IP View Configuration Menu 61 Offline Menus 62 Configuration Changes 63 Drive Operations Menu 64 4 Operator Tasks 67 Power on the Drive 68 Power off the Drive 68 IPL the Drive 69 Write protect Enable a Data Cartridge 70 Load a Data Cartridge 71 Unload a Data Cartridge 72 Clean the Drive 73 Menu System Tasks 74 Place the Drive Online 74 View Drive Configuration 74 View Firmware Release
52. cal ess Tape j None Attributes Drive DSE Mode Make Code j eee A ESOS Mae e adress Tape Bar Negotiation 22 ogical Tape ee E Usage Mode Standard Drive Make Data Cd sa Y E Address Language SCSI Protect Tape view ore Selection Speed 2 Standard Rebuild MIR Firmware r Eo Label VolSaf SCSI Level olSate a Recovery Protect Write Read Usage Process Laser Diagnostic a Ma A ae a Full Code re ne PRML Attributes Servo Head Stratix and l E N AAA Emaon PRML Diagnostic i Excaliber T9840 A St ASIC Mode Sante rH pe Emulation Servo Load Firmware T9840A B Unload Release Library VolSafe Tape Bar only Diagnostic Level Address Usage Usage Ae SS Tape Bar Exit or Loop I rosaoc ap oer Full Code Language Usage FICON ONLY l a r Selection Mode Emulation E Language l Ea Mode lecti WorldWide m pao 1 A Name H ra EE ee ress World Wide gt Full Code Usage Name L CSL Emulation Full Code PowerUp Mode Custom Serial Mode ee culation Number 3590 __ Library Mode Mode only World Wide Pass Il Name H E Library Save if o CSL Address Needed World Wide Power Up PA E A o clo A austere Me Power Up Note oo Number 3590 Needed Mode The TCP IP Configuration Mode only submenus are for use by 2 ExitorLoop World Wide authorized service Save if Name H personnel only Needed Exit or Loop u
53. cation is introduced in this chapter Information in chapters 3 and 4 of this document rely on use of the physical operator panel 95739 Revision YA 39 Front Panel FIGURE 2 1 Front Panel The T9840 tape drive front panel is the operator s interface with the drive The panel features a cartridge load unload slot four indicator lights four switches a manual unload device and an alphanumeric display with an optional tape bar FIGURE 2 1 T9840 Operator Panel ACTIVITY SERVICE INDICATOR INDICATOR MANUAL POWER CLEAN IPL UNLOAD INDICATOR SWITCH DEVICE LOAD UNLOAD UNLOAD MENU TAPE SLOT SWITCH DISPLAY SWITCH SELECT CARTRIDGE SWITCH 053117 40 19840 User s Reference Manual September 2008 Chapter 4 Operator Tasks describes how to use the switches to perform operations Chapter 5 Indicators and Messages describes how to interpret the indicators and display messages Load Unload Slot The load unload slot is the opening in the front panel that accepts 9840 Tape Cartridges that you load by hand that a T9840A CSL loads or that a library robotic hand loads After a tape cartridge is inserted the loader mechanism raises to engage the tape cartridge and draw it into the loaded position After an unload command the loader mechanism rewinds the tape to the mid point and ejects the cartridge into the slot for removal Revision YA 95739 Indicators Front Panel TABLE 2 1 d
54. ce port of a non encrypiton drive has caused problems Sun neither supports nor assumes any responsibility for unauthorized use of the maintenance port by non Sun personnel Encryption Encryption is based on the science of cryptography and is one of today s most effective ways to achieve data security To read an encrypted file you must have access to the key that enables the drive to decipher the data The T9840D tape drive employs a device based or data at rest encryption solution The drive is shipped from the factory encryption capable but not encryption enabled You must explicitly enable the drive for encryption Note A tape drive that has not been enabled for encryption can neither read nor append to any encrypted data cartridge An encryption enabled drive can m Write to the data cartridge in encrypted mode only by using its assigned write key m Read an encrypted data cartridge if it has the proper read key m Read non encrypted data cartridges m Format tape cartridges An encryption enabled drive cannot m Append write to a non encrypted data cartridge m Mix encrypted and non encrypted data on the same cartridge Encryption Resources For additional information on the encryption capabilities and features refer to m Crypto Key Management System Installation and Service Manual PN 3161949xx m Crypto Key Management System System Administrator Guide PN 3161951xx 24 19840 User s Reference Manual Sept
55. covery Protect Usage l Process ml a ME Port A and B Full Code Usa PRML Attributes ge rn ae Emulation PRML Emulation Language T9840A B eras Mode Selection only mu aon T9840A B rae VolSafe Tape Bar only ess d Usage Usage Tape Bar Sn i Full Code Language Usage ower A A Mone p mEn Selection ones Mode VolSafe Selection World Wide F Usage Name H Library PSA VolSafe qq Full Code Usage World Wide las A Name L CSL Emulation Full Code Power Up Mode e Serial Mode T Emulation a ibrary Mode _ Number World Wide Address O Etuk f et oa ES The TCP IP Configuration World Wide Power Up submenus are for use Name L Mode CSL by authorized service er a P U personnel only Serial Serial ower Up Number Number Mode Exit or Loop Exit or Loop World Wide TT Name H World Wide Name L Serial Number Exit or Loop 053411 Revision YA e 95739 54 19840 User s Reference Manual September 2008 Online Menu Operation Fibre Channel View Configuration Menu Tree T9840A B C Use the online view configuration menu tree as a brief guide Online Offline Press Select to toggle then press Menu to set Port X YYY A B and ENA DIS View CFG View Configuration Press Select to enter press Menu to bypass Cmprss xxx Yes Off No compression mode Full DSE x Y N data security erase mode SL Prot x Y N standard label protection mode View PrtA view current port attributes Hard PA xx Y N Physical Address PA xx ddd PA hex
56. ct authorized service personnel data onto the data cartridge tape or the tape drive cannot position the data cartridge tape DatCrFaill The tape drive cannot create reformat or Ensure that the data cartridge tape is write reclaim a cartridge tape enabled or try to reformat the tape on another drive If the problem persists contact authorized service personnel DmpCrFaill The tape drive cannot create reformat or Ensure that the data cartridge tape is write reclaim a diagnostic dump tape enabled If the problem persists contact authorized service personnel DmpCrFail2 The tape drive cannot read the format of Retry the operation or try another cartridge the data cartridge tape tape If the problem persists contact authorized service personnel DmpWrFaill The tape drive cannot write diagnostic Contact authorized service personnel DmpWrFail2 There is no diagnostic dump data to process Contact authorized service personnel XXXX Dmp y Alternates with an asterisk after completion of IPL where xxxx the FSC of last dump data collected and Y number of uncollected dumps in non volatile memory Contact authorized service personnel who accesses the diagnostic data and collects it to tape or to the host 95739 Revision YA Chapter 5 Indicators and Messages 81 Messages TABLE 5 2 Operator Panel Display Messages Continued Display Mean
57. d into the Equipment and executes below the decompile or otherwise reverse engineer the external user interface of such Equipment Internal Code except as decompilation might be Microcode includes both Internal Code and expressly permitted under applicable European Maintenance Code and might be in magnetic or law solely for the purpose of gaining other storage media integrated circuitry or other information that allows interoperability when media such information is not otherwise readily 2 The Equipment you have acquired by purchase or available or lease is manufactured by or for StorageTek and contains Microcode By accepting and operating this Equipment you acknowledge that StorageTek or its 95739 Revision YA Notices 21 iii sublicense assign or lease the Internal Code 8 or permit another person to use such Internal Code or any copy of it Nothing in the license set forth above or in this entire Notice shall convey in any manner to you any license to or title to or other right to use any Maintenance code or any copy of such Maintenance Code Maintenance Code and StorageTek s service tools and manuals might be kept at your premises or they might be supplied with a unit of Equipment sent to you and or included on the same media as Internal Code but they are to be used only by StorageTek s customer service personnel or those of an entity licensed by StorageTek all rights in and to such Maintenance Code service to
58. d xxxx 82 Loading 82 Locating 82 Memory Err 82 NTReady A 82 NTReady F 82 NTReady U 82 Offline 76 Offline alternating with asterisk 82 Online 83 OnLn Pend 83 operator panel display 80 operator panel display translated 85 Power Fail 83 Reading 83 Ready A 83 Ready F 83 Ready H 83 Ready L 83 Ready U 83 Rewinding 83 Save Fails 83 Saving Dump 83 Start Init 83 Trapped 83 Unloading 83 UnWr xxxx 83 Write Prot 83 Writing 83 xxxx Dmp y 81 95739 Revision YA messages tape drive display 42 MIR build 77 N notes description 14 NTReady A message 82 NTReady F message 82 NTReady U message 82 O offline menu system 62 setting the drive 75 Offline alternating with asterisk message 82 Offline message 76 online menu 53 setting the drive 74 Online message 83 OnLn Pend message 83 operator panel display messages 80 menu system 51 switches 44 tape drive 40 organization of this manual 13 overview menus structure 51 P package a cartridge for shipping 96 place the drive offline 75 place the drive online 74 Power Fail message 83 power indicator 41 power off the drive 68 power on the drive 68 precauci n mensajes en el manual 14 properties folder 49 publication containing related information 15 organization of this manual 13 PWR LED 46 R ReadCustTp command 64 Reading message 83 Ready A message 83 Ready F message 83 Ready H message 83 Ready L message 83 Ready U message 83 related publication
59. decimal index valid only when Hard PA is yes Soft PA xx HI LO only when Hard PA is no MaxSz xxxx 2112 2048 1280 1024 768 maximum data frame size A _I xxxxxx 24 bit address ID when port login is complete H xxxxxxxx first half 64 bit port node world wide name L xxxxxxxx second half 64 bit port node world wide name WWN Custom only when custom or dynamic WWN is set View PrtB current port B attributes same sub menus as port A Tape Bar x Y N tape completion indication English Espanol Francais Italiano Deutsch current language VolSafe X Y N determines the VolSafe capability of the drive FullCode X Y N determines whether a full code image is in drive memory Emul xxxxx STD 3590 3490E displays the active emulation mode special modes used only when directed by Engineering or Tech Support Lib Adr xy FF 00 13 2 character hexidecimal library address manufacturing setting is FF and it must be changed to a valid address when the drive is installed in a 9310 library CSL Xxxxxx System Auto Manual CSL power up mode H xxxxxxxx first half 64 bit drive node world wide name L xxxxxxxx second half 64 bit drive node world wide name WWN Custom only when custom dynamic WWN is set S N xxxxxx drive serial number last six characters of drive DMOD Exit CFG exit view configuration Press Select to exit press Menu to return to the View CFG submenu 95739 Revision YA
60. densitry tape was attempted to be read on a drive only capable of reading lower density tapes Retry with a low density tape CHK A74E A high density tape was loaded on a low density drive or a low density tape was loaded on a high density drive In either case the drive cannot write to the tape The MIR cannot be written on the tape during the unload process so there is no point in running the build MIR function If it is a high density tape rebuild the MIR on a high density drive If it is a low density tape rebuild the MIR on a low denisty drive 84 19840 User s Reference Manual September 2008 Revision YA 95739 Translated Messages Messages TABLE 5 4 lists operator panel display messages that are translated when the drive configuration Language option is set to something other than English TABLE 5 4 Translated Display Messages English Espanol Francais Italiano Deutsch CLEANING LIMPIEZA NETTOYAGE PULIZIA REINIGEN CHK XXXX ERR XXXX ERR XXXX ERR XXXX PRUEF XXXX ERASING BORRANDO EFFACEMENT CANCELLA LOESCHEN Locating Localizar Recherche Ricerca Suchen LOAD XXXX CARGA XXXX CHARG XXXX CARIC XXXX ADEN XXXX Loading Cargando Chargement Carico Laden NT Ready A No Listo A NPret A No Prnt A N Bereit A NT Ready F No Listo F NPret F No Prnt F N Bereit F NT Ready U No Listo U NPret
61. determines the VolSafe capability of the drive FullCode X Y N determines whether a full code image is in drive memory Emulation Mode displays current emulation based on active interface Emul STD standard 3590 3490E special modes used only when directed by Engineering Tech Support Lib Adr xy 2 character hexidecimal library address CSL Xxxxxx System Auto Manual CSL power up mode H xxxxxxxx first half 64 bit drive node world wide name L xxxxxxxx second half 64 bit drive node world wide name WWN Custom only when custom dynamic WWN is set S N Xxxxxx Normal Custom appears only when in 3590 or 3590s emulation mode S N xxxxxx drive serial number last six characters of drive DMOD Exit CFG exit view configuration Press Select to exit press Menu to return to the View CFG submenu Chapter 3 Menus 57 Online Menu Operation ESCON View Configuration Menu Tree Use the online view configuration menu tree as a brief guide Online Offline Press Select to toggle then press Menu to set Port xxx ENA DIS enables or disables the ESCON port View CFG View Configuration Press Select to enter press Menu to bypass Cmprss Xxx Yes Off No compression mode Full DSE X Y N data security erase mode Drv Adr xy 2 character hexidecimal logical drive address usually 00 SL Prot X Y N standard label protection mode Lmit ERP X Y N limit error recovery process to 10
62. dress when the drive is installed in a 9310 library H xxxxxxxx first half 64 bit drive node world wide name L xxxxxxxx second half 64 bit drive node world wide name WWN Custom only when custom dynamic WWN is set S N xxxxxx drive serial number last six characters of drive DMOD Exit CFG exit view configuration Press Select to exit press Menu to return to the View CFG submenu Chapter 3 Menus 59 Online Menu Operation FICON View Configuration Menu Tree T9840D Use the online view configuration menu tree as a brief guide Online Offline Press Select to toggle then press Menu to set View CFG View Configuration Press Select to enter press Menu to bypass Intf XXXXX FICON FCP View PrtA view current port attributes A xxxxxxay 24 bit address identifier connection type and port speed when port log in is complete B xxxxxxay when viewing port B SFP module parameters 2G MM0300m 2G SM10 0k Hard PA x Y N Physical Address PA xx ddd PA hex decimal index only when Hard PA is yes Soft PA XX HI LO only when Hard PA is no Rate xxxx Auto fixed rate 2Gb or 1Gb interface speed negotiation MaxSz xxxx 2112 2048 maximum data frame size H xxxxxxxx first half 64 bit port node world wide name L xxxxxxxx second half 64 bit port node world wide name WWN Custom only when custom or dynamic WWN is set View PrtB current port B attributes same sub menus as port A Emul xxxxx 3490 35
63. ect switch Yes to enter the view configuration submenus The first configuration setting appears in the operator panel display window 4 Press either the Menu or the Select switch to step through the configuration settings Note In the drive online state the Select switch has the same stepping function as the Menu switch except when answering a displayed question 5 Press either the Menu or Select switch until Exit CFG appears in the display window 6 Press either the Select switch Yes to exit the submenu or the Menu switch No to repeat the view configuration sequence 7 Press the Menu switch until Exit Menu appears in the display window 8 Press either the Select switch Yes to exit the menu system or the Menu switch No to return to the online offline selection menu View Firmware Release Level To view the firmware release level 1 Press the Menu switch to enter the menu system 2 Press the Menu switch until a number in the form of Rx yy zzzc appears in the display Where x is the major revision level yy is the minor revision level zzz is the integration level c is the channel type f is Fibre Channel s is SCSI e is ESCON FICON 3490 image m is ESCON FICON 3590 image 3 Press the Menu switch repeatedly until Exit Menu appears in the display window 4 Press either the Select switch to exit the menu system or press the Menu switch to repeat the Online Offline selection Place the
64. ect switch to increment the value 3 Press the Menu switch when the desired value appears in the display the character stops flashing 4 The adjacent character to the right flashes Repeat steps 1 through 3 to set the proper value for the second or succeeding character When you have set all characters go to step 5 5 Press the Menu switch to advance to the next menu item Note If you press the Select switch the first character in the value sequence flashes and you can increment the value The last menu item after a change is typically Save IPL Press the Select switch to accept the change and start the drive IPL However if you press the Menu switch the display will typically advance to Exit Menu press Select to exit or Menu to return to the first item in the submenu 95739 Revision YA Chapter 3 Menus 63 Offline Menus Drive Operations Menu The Drv Menu branch of the main menu is the same for Fibre Channel SCSI ESCON and FICON interfaces FIGURE 3 3 shows an expansion of the drive operations sub menus Note that the menu items both preceding and following the Drv Menu branch vary with the type of data path interface see FIGURE 3 2 on page 62 for specific menu items FIGURE 3 3 Drive Operations Menu Tree EE ien Online Select Offline Notes See interface Menu Tree NA T9840A 3 Offline only Firmware release number nsert Firmware tape
65. ember 2008 Revision YA 95739 Tape Drive Encryption Status LED Encryption capable drives have a tri color encryption status LED on the rear panel see TABLE 1 1 on page 26 for an explanation of the status indications Drive trays that fully enclose the drive usea light pipe to transfer the LED indication to the rear of the tray see the CRYPT label in the figure below If the encryption status LED is green it indicates that the drive is encryption capable but not encryption enabled In this state the drive functions only in a non encryption safe mode and cannot read write encrypted data cartridges However the drive can function normally for non encryption tasks Once the drive is encryption enabled the LED turns red to indicate that the drive is armed and functioning in the encryption mode In this state the drive can read write encrypted data cartridges The drive can also read non encrypted data cartridges but cannot write to non encrypted data cartridges FIGURE 1 2 Encryption Status LED SL8500 Library Drive Tray 02020202 O O o QO O O O O O O QQ OO O O O O OG SOS 5 OSOS C54103 95739 Revision YA Chapter 1 Overview 25 Configurations The following table interprets the various states of the encryption status LED Refer to the Crypto Key Management documentation for additional information TABLE 1 1 Encryption Status LED State Descriptions L
66. eptember 2008 Revision YA 95739 Typographical Conventions Typographical conventions highlight special words phrases and actions in this publication Item Example Description of Convention Commands Mode Select Initial cap Document titles System Assurance Guide Italic font Emphasis not or must Italic font Menu options Exit Bold Hypertext links Figure 1 on page 25 Blue prints black in hardcopy publications URLs http www sun com Blue prints black in hardcopy publications Related Publications Publications relating to the tape drive Document Title Part Number 4410 11 20 30 and 9310 11 20 Automated Cartridge System Hardware Operator s 9206 Guide Nearline Enterprise 9310 4410 9360 LSM System Assurance Guide ML6500 L700x L1400x Tape Libraries and Pass Thru Port Ordering and Configuration Guide MT9112 L700x L1400x Tape Libraries and Pass Thru Port Operator Guide 95845 L5500 Automated Cartridge System System Assurance Guide MT9142 L5500 Automated Cartridge System Operator s Guide 96063 StorageTek SL8500 Modular Library System User s Guide 96154 TimberWolf 9740 Library Storage Module System Assurance Guide MT5001 TimberWolf 9740 Library Storage Module Hardware Operator s Guide 95693 T9x40 Tape Drive Service Reference Manual 95740 Crypto Key Management System Installation and Service Manual 3161949xx Crypto Key Management System System Administrator Guide
67. erations A physical connection electrical or optical between two nodes of a network The device that physically loads data cartridges for use Glossary 101 M magnetic tape manual operation MB menu Multiple Virtual Storage MVS Multiple Virtual Storage Enterprise Systems Architecture MVS ESA MVS MVS ESA N network O offline online operator control panel P performance 102 T9840 User s Reference Manual September 2008 A tape with a magnetizable layer on which data can be stored T Processing of data in a system by direct manual techniques IBM Megabytes or 1 048 576 bytes A list of options displayed to the user by a data processing system from which the user can select an action to be initiated T IBM s Multiple Virtual Storage consisting of MVS System Product Version 1 and the MVS 370 Data Facility Product operating on a System 370 processor IBM An extended version of IBM s MVS See Multiple Virtual Storage See Multiple Virtual Storage Enterprise Systems Architecture An arrangement of nodes and branches that connects data processing devices to one another through software and hardware links to facilitate information interchange Neither controlled by nor communicating with a computer IBM Pertaining to the operation of a functional unit when under the direct control of the computer T A functional unit that contains switches used to contro
68. escribes T9840 Tape Drive operator panel indicators TABLE 2 1 Operator Panel Indicators Indicator Indication Explanation power green Off Power is not applied Flashing Unit is powering up performing IPL or collecting dump data Flashing does not stop On steady IPL failed Power applied and IPL complete activity green Off Flashing On steady Tape cartridge is not loaded Tape cartridge is loaded and the tape is moving Tape cartridge is loaded and the tape is stopped clean amber On steady Drive requires cleaning because 1 A firmware defined length of tape has passed over the R W heads 2 A read write perm permanent error is detected and at least one half the firmware defined length of tape has passed over the R W heads See Clean the Drive on page 73 for use of cleaning cartridges service red Off Flashing On steady Error s have not been detected Error s detected and dump data has been saved to the EEPROM The message DumpAgain displays if the drive detects the same Fault Symptom Code FSC within one minute Manually initiate IPL If the IPL does not eliminate the problem contact authorized service personnel A hardware error is detected and the drive is not functional If a manually initiated IPL does not eliminate the problem contact authorized service personnel Manual Unload Device The manual unload device MUD is a mechanism
69. h T9840A B C drives The extra measures essentially involve creation and management of separate media pools sub pools for m 19840A B formatted written data cartridges m T9840C formatted written data cartridges m T9840D formatted written data cartridges Guidelines for creation and maintenance of media pools sub pools are located in ACSLS HSC and independent software vender ISV documentation sets TABLE 1 2 Cartridge Read Write Compatibility Drive Model Compatibility T9840A T9840B T9840C T9840D Read a cartridge formatted by T9840A and T9840A and T9840A T9840A T9840B T9840B T9840B and T9840B T9840C T9840C and T9840D Write or append data to a cartridge T9840A and T9840A and T9840C T9840D formatted by T9840B T9840B 95739 Revision YA T9840A B tape drives cannot read from a data cartridge written by either T9840C or T9840D tape drive because of the higher density formats and must have an appropriate drive firmware level to even identify the higher density data cartridges m T9840A a R1 33 103 or higher to identify a T9840C written cartridge a R1 41 105 or higher to identify a T9840D written cartridge m T9840B a R1 33 303 or higher to identify a T9840C written cartridge a R1 41 305 or higher to identify a T9840D written cartridge m T9840C R1 41 505 or higher to identify a T9840D written cartridge Without the appropriate drive firmware level a T9840A B drive would consider a higher de
70. ing Recommended Action DumpAgain alternating with CHK xxxx where xxxx is an FSC The tape drive detected the same error within a minute Note The Service indicator is flashing IPL the tape drive If the problem persists contact authorized service personnel DumpToHost The dump or event log is being None transferred to the host operator panel switches are locked Exp ClCart The cleaning cartridge is used up Replace the cleaning cartridge Fix CfgErr The checksum does not match after an Contact authorized service personnel IPL Init XXXX where xxxx is an FSC An initialization error occurred Contact authorized service personnel IPL Pend The IPL switch has been pressed None LOAD CC The common controller code is loading None IPL is proceeding LOAD ESCON ESCON firmware is loading IPL is None proceeding LOAD FIBRE Fibre Channel firmware is loading IPLis None proceeding LOAD FICON FICON firmware is loading IPL is None proceeding LOAD SERVO The servo code is loading IPL is None proceeding LOAD SCSI SCSI firmware is loading IPL is None proceeding LOAD xxXxX The load or unload operation failed If the load failed insert another cartridge tape If where XXXX is an FSC it loads successfully suspect the original tape If another tape fails to load IPL the tape drive If the problem persists contact your Sun service representative
71. ion describes the T9840 Tape Drive and Tape Cartridge performance Tape Drive TABLE A 8 lists the performance specifications of the T9840 tape drive TABLE A 8 19840 Tape Drive Performance Specifications Value Characteristic T9840A T9840B T9840C T9840D Capacity and Performance Capacity native 20 GB 20 GB 40 GB 75 GB Data buffer size 8 MB 32 MB 64 MB 64 MB tape speed read write 2 m s 4 m s 3 295 m s 3 4 m s Performance native head to tape uncompressed 10 MB s 19 MB s 30 MB s 30 MB s compressed maximum 35 MB s 60 MB s 60 MB s 60 MB s Burst FC amp FICON 100 MB s 200 MB s 200 MB s 200 MB s Burst ESCON 17 MB s 17 MB s 17 MB s 17 MB s Interface data Fibre Channel 1 Gb 2 Gb 2 Gb 2 Gb Ultra SCSI HVD 40 MB s 40 MB s N A N A ESCON 17 MB s 17 MB s 17 MB s 17 MB s FICON N A 2 Gb 2 Gb 2 Gb Access times Tape load and thread to ready 7 sec 7 sec 6 5 sec 8 5 sec File access first average 8 sec 8 sec 8 sec 8 sec Rewind maximum average 16 8 sec 16 8 sec 16 8 sec 16 8 sec Unload 8 sec 8 sec 11 5 sec 12 5 sec Reliability Mean time between failure MTBF Power on 100 duty cycle 290 000 hr 290 000 hr 290 000 hr 290 000 hr Tape load 10 day 100k loads 240 000 hr 240 000 hr 240 000 hr 240 000 hr Tape path motion TPM 70 duty cycle 216 000 hr 216 000 hr 216 000 hr 216 000 hr Head life 70 TPM duty cycle 5 years 5 years 5 years 5 years Uncorrected bit error rate 1 x 10 18 1x 10 18 1 x 10 18 1x 1018 U
72. ion settings of a T9840D tape drive You might prefer to use this method instead of the physical drive panel See the Virtual Operator Panel User s Guide P N 96179 for pertinent information 52 19840 User s Reference Manual September 2008 Revision YA 95739 Online Menu Operation Online Menu Operation When the drive is Online the menus shown in FIGURE 3 1 on page 54 are available Press Menu to advance to the View Configuration menu View the drive configuration View the TCP IP configuration N A for the T9840A View the drive firmware level View the ASIC firmware level FICON drives only View the CSL firmware level Note Individual submenu items in the illustration are based upon the T9840A B C drives using a code level prior to 1 42 x07 The content of the figure was created before the T9840D tape drive was available The note on the TCP IP menu does not apply to the T9840D drive because the drive Ethernet port can be used with the Crypto Key Management System 2 0 View Configuration Menu The View Configuration menu is presented in more detail in the following sections Fibre Channel View Configuration Menu Tree T9840A B C on page 55 Fibre Channel View Configuration Menu Tree T9840D on page 56 SCSI View Configuration Menu Tree on page 57 ESCON View Configuration Menu Tree on page 58 FICON View Configuration Menu Tree T9840B C on page 59 FICON View Configuration
73. ipment damage Cables that connect peripherals must be shielded and grounded refer to descriptions in the cable instruction manuals Operation of this equipment with cables that are not shielded and not correctly grounded might result in interference to radio and TV reception Changes or modifications to this equipment that are not expressly approved in advance by StorageTek voids the warranty In addition changes or modifications to this equipment might cause it to create harmful interference United States FCC Compliance Statement The following compliance statement pertains to Federal Communications Commission Rules 47 CFR 15 105 Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the interference at his or her own expense 95739 Revision YA 19 Japanese Compliance Statement The following compliance statement in Japanese pertains to VCCI EMI regulations CO
74. it is used The regions of recorded tape containing user data formed as discreet longitudinal tracks similar to railroad tracks Pertaining to the detection and isolation of errors in programs and faults in equipment A drive controls the movement of the tape and records or reads the data on the tape as desired by the customer To copy the contents of all or part of storage to collect error information An IP protocol that a host uses to obtain all necessary configuration information including an IP address The use of programming techniques and special machine features to permit a computing system to execute programs written for another system IBM The translation of data into a secret code Encryption is one of the most effective ways to achieve data security To read an encrypted file you must have access to a special key or password that enables you to decipher it A representation of the goals organizational structure business processes and information resources and requirements of an enterprise IBM A set of IBM products and services that provide a dynamically connected environment within an enterprise IBM Any of the physical conditions required for the protection and proper operation of a functional unit the requirement is usually specified as a nominal value and a tolerance range For a device there may be more than one set of environmental requirements for example one set for transport another for st
75. ittee for Information Technology Standards standard that defines an ultrahigh speed content independent multilevel data transmission interface that supports multiple protocols simultaneously Fibre Channel supports connectivity to millions of devices over copper and or fiber optic physical media and provides the best characteristics of both networks and channels over diverse topologies An ESA 390 and zSeries computer peripheral interface The I O interface uses ESA 390 and zSeries FICON protocols FC FS and FC SB 2 over a Fibre Channel serial interface that configures units attached to a FICON supported Fibre Channel communications fabric A chamnel having a Fibre Channel connection FICON channel to control unit I O interface that uses optical cables as a transmission medium May operate in either FC or FCV mode To prevent the erasure or overwriting of data stored on data cartridges See also write protect switch An ordered set of instructions and data stored in a way that is functionally independent of main storage for example microprograms stored in ROM T Field replaceable unit Fault symptom code File Transfer Protocol Gigabit equal to 10 bits Gigabits per second One X 230 bytes binary or 1 X 10 decimal Revision YA 95739 H hardware host host interface hub I indicator Initial Program Load IPL initialization input output I O internet protocol IP internet protocol
76. l MIR Processing Every time a tape cartridge is loaded the MIR is read from the tape media and saved in the drive memory When the MIR is loaded in drive memory an invalid flag is written in the tape resident MIR The tape resident MIR is marked invalid because it does not reflect results of activity in the current mount session All subsequent MIR accesses during the current mount session are saved in the memory resident MIR When the tape cartridge is unloaded as part of the unload routine the memory resident MIR information is written to the tape resident MIR and the MIR invalid flag is turned off A copy of the memory resident MIR is stored in the drive s persistent memory EEPROM and used should the MIR fail to be written because of a power failure or firmware problem SNO or should not occur Cross Density MIR Processing Whenever a data cartridge is loaded that was written in a data density format that is different from the one used when the drive writes model specific MIR processing occurs The following explanations cover m T9840D tape drive loaded with a lower density cartridge m T9840C tape drive loaded with aT9840D written data cartridge m T9840C tape drive loaded with a T9840A B written data cartridge m T9840A B drive loaded with a high density tape cartridge T9840D Tape Drive Loaded With a Lower Density Cartridge When the T9840D drive detects that a data cartridge is loaded the drive first looks in the designated
77. l all or part of a computer and possibly the indicators giving information about its functioning T One of two major factors on which the total productivity of a system depends Performance is largely determined by a combination of throughput response time and availability IBM Revision YA 95739 port R R W read write head reclaim release rewind ROM S SCSI SLC small computer system interface SCSI StorageTek Library Console submenu A specific communications end point within a host A port is identified by a port number IBM Read write The data sensing and recording unit of a tape drive IBM The act of overwriting a 9840 legacy data cartridge by a newer generation drive For example a cartridge written by a T9840A drive can be overwritten reclaimed by either a T9840C or T9840D drive while a cartridge written by a T9840C drive can be reclaimed by a T9840D drive A distribution of a new product or new function and fixes for an existing product IBM To move tape from the take up hub to the supply hub IBM Read only memory See small computer system interface See StorageTek Library Console An input and output bus that provides a standard interface between devices The operator panel software application used for the SL8500 Modular Library System A menu related to and reached from a main menu IBM subsystemA system that is part of some larger system switch
78. location for a T9840D MIR If a T9840D MIR is not found the drive then checks for a T9840C MIR and if its not found it then checks for a T9840A B MIR The processing for these operations is described in the sections below If the MIR cannot be read the T9840D drive attempts to recover its contents using any portions of the MIR that can be read and the contents of the Format Identity Burst FIB Note The FIB is written in a format that can be read by T9840C and T9840A B drives if they have an appropriate level of firmware The T9840D uses a memory resident copy of the MIR to access user data pointers for read only functions Statistical counters are continuously updated in the memory resident MIR with any drive activity When the data cartridge is unloaded the T9840D drives writes the FIB to the high density MIR location Notes a When the T9840D drive identifies the data cartridge as a low density data format i e written by a T9840C or T9840A B it displays Ready L on its operator panel a The T9840D tape drive cannot correct or cause an invalid MIR on a T9840C written data cartridge A T9840C MIR can only become invalid during a mount on a T9840C drive 95739 Revision YA Chapter 1 Overview 33 Mixed Media Management a The T9840D tape drive cannot correct or cause an invalid MIR on a T9840A B written data cartridge A T9840A B MIR can only become invalid during a mount on a T9840A B drive a Ifa T9840C or T984
79. ment ii is required by such license authorizes you the end user to execute the Equipment to perform its data storage and retrieval Internal Code solely to enable the specific unit of functions and iii executes below the user interface Equipment for which the copy of Internal Code is of such Equipment Internal code does not include provided to perform its data storage and retrieval other Microcode or software including data files functions in accordance with StorageTek s or its which might reside or execute in or be used by or in licensor s official published specifications connection with such Equipment including 4 Your license is limited to the use of the Internal Code without limitation Maintenance Code as set forth You might not use the Internal Code for c Maintenance Code is defined as Microcode and any other purpose You might not for example do other software including data files which might any of the following reside or execute in or be used by or in connection with Equipment and which detects records displays and or analyzes malfunctions in the Equipment i access copy display print adapt alter modify patch prepare Derivative works of transfer or distribute electronically or pie ae r otherwise or otherwise use the Internal Code d Microcode is defined as a set of instructions software that is either imbedded into or is to be ii reverse assemble decode translate loade
80. minutes 98x Yyyyyy x c Normal Emul ID the drive as high density during an MVS swap x T9840A B only in 3590 emulation modes Tape Bar X Y N tape completion indication English Espanol Francais Italiano Deutsch current language VolSafe X Y N determines the VolSafe capability of the drive FullCode X Y N determines whether a full code image is in drive memory Emul xxxxx 3490 3590 displays the active emulation mode special modes used only when directed by Engineering or Tech Support Lib Adr xy FF 00 13 2 character hexidecimal library address manufacturing setting is EF and it must be changed to a valid address when the drive is installed in a 9310 library CSL Xxxxxx System Auto Manual CSL power up mode S N xxxxxx drive serial number last six characters of drive DMOD Exit CFG exit view configuration Press Select to exit press Menu to return to the View CFG submenu 58 19840 User s Reference Manual September 2008 Revision YA e 95739 Online Menu Operation FICON View Configuration Menu Tree T9840B C Use the online view configuration menu tree as a brief guide Online Offline Press Select to toggle then press Menu to set View CFG View Configuration Press Select to enter press Menu to bypass 95739 Revision YA Intf FICON View PrtA view current port attributes A xxxxxxay 24 bit address identifier connection type and port speed when port log i
81. ms occur with the tape drive In some cases you might be able to correct the problem In other cases you must contact your service representative as described in this chapter If you have as much of the following information as possible when you place a service call the process is much easier Account name Site location number Contact name Telephone number Equipment model number Tape drive address Tape drive code level Tape drive serial number Urgency of the problem Fault Symptom Code FSC from the tape drive s front panel display screen rack mount or as displayed on the host system display screen m Problem description m Is the tape drive in a library ___ If so which library m If the tape drive was running properly before this incident What changes has the site made recently a What software application was running at the time of the failure a Were any hardware configuration changes made recently a Were any software configuration or upgrades done recently a Were any additions or deletions to the hardware or software done at the site m If the drive was NOT running properly before this incident what was the last problem 95739 Revision YA Preface 17 18 T9840 User s Reference Manual September 2008 Revision YA 95739 Notices Please read the following compliance and warning statements for this product Caution Potential equ
82. n De Save if Needed Exit or Loop 053493 62 19840 User s Reference Manual September 2008 Revision YA e 95739 Offline Menus Configuration Changes You can change configuration settings from the drive offline menu system You will continue to use the Menu and Select switches to navigate the offline menu system You enter the configuration or TCP IP submenu when you press the Select switch while the main menu item appears in the display The first option in the submenu appears in the display to confirm your selection There are three basic types of change mechanisms m Toggles Options m Values A toggle is a choice between two values An example is the DSE mode option where you must choose between the choices of YES or NO If YES appears in the display and you wish the selection to be NO 1 Press the Select switch No appears in the display 2 Press the Menu switch to advance to the next menu item Options are similar to toggles but you must choose among three or more values An example is the Compression mode option that has the choices of Yes No or OFF 1 Press the Select switch until the desired choice appears in the display 2 Press the Menu switch to advance to the next menu item A value is typically a numeral or a hexadecimal character Often you will change an address which consists of one or more characters 1 Press the Select switch the left most character of the value flashes 2 Press the Sel
83. n is complete B xxxxxxay when viewing port B SFP module parameters 2G MM0300m 2G SM10 0k Hard PA x Y N Physical Address PA xx ddd PA hex decimal index only when Hard PA is yes Soft PA XX HI LO only when Hard PA is no Rate xxxx Auto fixed rate 2Gb or 1Gb interface speed negotiation MaxSz xxxx 2112 2048 maximum data frame size H xxxxxxxx first half 64 bit port node world wide name L xxxxxxxx second half 64 bit port node world wide name WWN Custom only when custom or dynamic WWN is set View PrtB current port B attributes same sub menus as port A Emul xxxxx 3490 3590 displays current emulation mode special modes used only when directed by Engineering or Tech Support Cmprss Xxx Yes Off No compression mode Full DSE x Y N data security erase mode Drv Adr xy 2 character hexidecimal logical drive address usually 00 SL Prot x Y N standard label protection mode English Espanol Francais Italiano Deutsch current language Tape Bar x Y N tape completion indication VolSafe x Y N enable VolSafe write once read many Full Code x Y N drive memory contains full code load CSL Xxxxxx Y N CSL operating mode System Auto Manual 98x Yyyyyy x c Normal Emul ID the drive as high density during an MVS swap x T9840B only in 3590 emulation modes Lib Adr xy FF 00 13 2 character hexidecimal library address manufacturing setting is FF and it must be changed to a valid ad
84. nce Manual September 2008 Revision YA 95739 Power Specifications Refer to the appropriate library System Assurance Guide for the physical dimensions and weights of the library and frame Power Specifications The power specifications for the T9840 tape drive are listed in the following table TABLE A 5 19840 Tape Drive Power Specifications Characteristic Value Input voltage 100 to 240 VAC Input frequency 50 to 60 Hz Power consumption T9840D T9840C m 61 7 W write m 65 W write m 43 W Idle with tape loaded m 45 W Idle with tape loaded m 35 W Idle no tape loaded m 38 W Idle no tape loaded SL8500 Power dissipation 345 Btu hr 95739 Revision YA Appendix A Specifications 89 Environmental Requirements Environmental Requirements This section lists the environmental requirements for the tape drive power supply and tape cartridge Tape Drive and Power Supply This section lists the environmental requirements for the tape drive and the power supply TABLE A 6 19840 Tape Drive and Power Supply Environmental Requirements Description Range Temperature Operating 15 to 32 C 59 to 90 F Shipping 40 to 60 C 40 to 140 F Storing 10 to 40 C 50 to 104 F Relative Humidity non condensing Operating 20 to 80 Shipping 10 to 95 Storing 10 to 95 Wet Bulb Maximum Operating 29 C 84 F Shipping 35 C 95 F Storing 35 C 95 F Altitude
85. nd T9840D tape drives Itis a guide for operating the drive and responding to operator panel messages that might occur while operating the drive The specific model suffix will be used only as required for differentiation Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Appendix A Appendix B Glossary Index Organization The organization of this guide is Overview provides an overview of the T9840 tape drive and its data cartridges Operator Controls describes the T9840 operator panel and its features Menus describes use and navigation of the T9840 tape drive s menu system Operator Tasks describes in detail the tasks the operator can perform Indicators and Messages describes the meaning and recommended action for the operator panel indicators and messages Specifications lists the physical and environmental specifications for the tape drive Cartridge Care describes the handling and care of cartridges Glossary defines some terms and abbreviations used in this guide The Index allows you to locate information in this manual 95739 Revision YA 13 gt gt A A Alert Messages Alert messages call your attention to information that is especially important or that has a unique relationship to the main text or graphic Note A note provides additional information that is of special interest A note might point out exceptions to rules or procedures
86. ndetected bit error rate 1 x 1033 1 x 1033 1 x 1033 1 x 1033 1 VR is a trademark of Overland Storage VR technology is used to achieve T9840C and T9840D capacity 2 Fibre Channel FC write and 55 MB s FICON write 92 19840 User s Reference Manual September 2008 Revision YA 95739 Tape Cartridge Performance Specifications TABLE A 9 lists the physical and performance specifications for the T9840 data cartridge The cleaning cartridges have the same physical specifications TABLE A 9 T9840 Data Cartridge Physical and Performance Specifications Characteristic Value Cartridge physical data Drive compatibility Form factor Width Length Height Weight Drop strength T9840A T9840B T9840C T9840D 1 2 in cartridge 3490 3490E 10 9 cm 4 29 in 12 5 cm 4 92 in 2 54 cm 1 0 in 262 g 9 17 oz 1 0 m 39 4 in Tape media data Capacity native uncompressed Tracks Track following servo Formulation Physical thickness Physical length Recordable length including MIR 20 GB T9840A T9840B 40 GB T9840C ZB 75 GB T9840D 288 T9840A T9840B T9840C 576 T9840D Factory pre recorded Advanced metal particle AMP 9 microns 271 m 889 ft 251 m 823 ft Reliability Archival life Short length durability Long life durability Load unloads Uncorrected bit error rate Permanent errors 15 30 years 80 000 write read passes minimum 6 500 write read passes minimum
87. nel version 1 0 12 or higher with the T9840D tape drive to perform many of the operator tasks listed above The Virtual Operator Panel provides a graphical user interface to accomplish task functions See the StorageTek Virtual Operator Panel Customer User s Guide part number 96179 for specific information 95739 Revision YA 67 Power on the Drive Power on the Drive To apply power to the desktop or rack mount configuration 1 Make sure the power cord is connected from the receptacle on the chassis rear panel to an AC power outlet or power strip 2 Make sure that all interface cables are fully seated 3 Set the power switch on the back of the drive or the rear panel to on The drive s will power on and perform an initial program load IPL m The drive power indicator flashes m Various messages relative to the IPL sequence appear in the operator panel display window These messages do not require any action from you When the drive successfully completes an IPL a The drive power indicator is steady a An asterisk appears in the operator panel display window Power off the Drive To remove power from the desktop and rack mount configuration 1 Make sure the tape drive is not in use Check for the following elements a There are no active jobs applications or programs using this drive b The operator panel activity indicator is steady and not flashing c The display window does not indicate any
88. ng using the offline drive operations menu Once a data cartridge is reformatted old data is no longer accessible because the reformatting and new data recording overwrites previous data areas Note You cannot reformat a VolSafe data cartridge with the offline drive operations submenu To reformat a cartridge Press the Menu switch to access the menu system a If the display shows Offline go to step 2 b If the display shows Online press the Select switch to place the drive offline Press the Menu switch until Drv Menu appears in the display Press the Select switch to enter the submenu Press the Menu switch until MakeDataTp appears in the display Press the Select switch Ld Data Tp appears in the display Inspect the cartridge for damage see Identify a Damaged Cartridge on page 95 Load a write enabled data cartridge in the drive load slot see Load a Data Cartridge on page 71 The drive reformats and ejects the data cartridge Remove the cartridge 76 19840 User s Reference Manual September 2008 Revision YA 95739 Menu System Tasks 9 Press the Menu switch until Exit Drv appears in the display 10 Press either the Select switch to enter the main menu or the Menu switch to repeat the drive operations menu 11 Press the Menu switch until Exit Menu appears in the display 12 Press either the Select switch to exit the menu system or the Menu switch to repeat the
89. not be read by a T9840C drive Ready L A loaded low density data cartridge is Use for read only jobs or intentionally over write enabled by the cartridge write write from BOT protect switch in the unlocked position Note Low density data files can be read but not revised by a T9840C D drive Ready U The loaded cartridge tape is write None enabled write unprotected Rewinding The tape drive is rewinding None Save Fails The new configuration cannot be saved because the read access memory RAM may be defective This message is associated with changing the tape drive configuration a task for authorized service personnel only SavingDump A dump is being saved to non volatile None memory Start Init Initialization has started None Trapped The IPL process is trapped in a loop IPL the tape drive again If the problem persists contact authorized service personnel Unloading A cartridge tape is unloading None UnWr xxxx where XXXX is an The Unload switch was pressed during a write operation Some data remains To write the unwritten data issue the command ESCON Swap in the VM MVS FSC unwritten environment Or Press the Unload switch again the unwritten data is lost Write Prot The tape drive attempted to write to a Change the switch on the data cartridge tape to write protected cartridge tape enable writing Writing The tape drive is writing data None 95739 Revision YA Chap
90. nsity formatted cartridge blank and available for scratch T9840A B drive attempts to read the data from an identified higher density data cartridge will fail Chapter 1 Overview 31 Mixed Media Management 32 The T9840C or T9840D tape drive can read data from a tape cartridge written by a T9840A B tape drive in the low density format but does not append data to that cartridge An attempt to append a low density data cartridge on a T9840C or T9840D drive will fail and sense byte data indicates an error similar to that of a file protected data cartridge Note For additional information about mixed media management see Cross Density MIR Processing Media Information Region The T9840 tape drives use information recorded on each tape cartridge to access and manage that tape cartridge while it is loaded in the drive This information is recorded at the beginning of the tape in an area known as the Media Information Region MIR The information contained in the MIR falls into two major categories m Statistical Counters Statistical counters include read write activity error activity cumulative mounts and other information that reflects tape cartridge usage m Data Pointers The data pointer information is basically a directory map used to locate the data on the physical tape media Since user data is compressed and written in drive controlled blocks on the tape a map is needed to efficiently locate the data after
91. ols and manuals being reserved by StorageTek or its licensors You agree that you shall not use or attempt to use the Maintenance Code or permit any other third party to use and access such Maintenance Code You the end user agree to take all appropriate steps to ensure that all of your obligations set forth in this Notice are extended to any third party having access to the Equipment You might transfer possession of the Internal Code to another party only with the transfer of the Equipment on which its use is authorized and your license to use the Internal Code is discontinued when you are no longer an owner or a rightful possessor of the Equipment You must give such transferee all copies of the Internal Code for the transferred Equipment that are in your possession along with a copy of all provisions of this Notice Any such transfer by you is automatically without further action on the part of either party expressly subject to all the terms and conditions of this Notice passing in full to the party to whom such Equipment is transferred and such transferee accepts the provisions of this license by initial use of the Internal Code You cannot pass to the transferee of the Equipment any greater rights than granted under this Notice and shall hold StorageTek harmless from any claim to the contrary by your transferee or its successors or assigns In addition the terms and conditions of this Notice apply to any copies of Internal
92. ons TABLE 5 2 Operator Panel Display Messages Display Meaning Recommended Action asterisk The tape drive is online but a cartridge tape is not loaded Load a cartridge tape as required ASIA Diags IPL diagnostics are running None Bank n Bad During boot a section of memory was found bad IPL the tape drive If the problem persists contact authorized service personnel BIdMIRFail Rebuild of Media Information Region MIR unsuccessful Note Code level 1 30 109 and higher displays CHK XXXX Boot Fail The IPL failed IPL the tape drive again If the problem persists contact authorized service personnel BT Monitor A sequence of switches accessed an IPL the tape drive If the problem persists engineering area contact authorized service personnel CC Diags IPL diagnostics are running None CHK xxxx where xxxx is an FSC An operational failure occurred the tape drive might automatically perform an IPL depending on the operational mode of the drive and the specific failure Wait for the IPL to complete and retry the operation If the problem persists contact authorized service personnel See TABLE 5 3 on page 84 for a list of codes that are most often caused by an operator error Cleaning Cleaning A cleaning cartridge is in the tape drive and is now cleaning None 80 19840 User s Reference Manual September 2008 Revision YA 95739 Message
93. orage and another for operation T A End of tape A discrepancy between a computed observed or measured value or condition and the true specified or theoretically correct value or condition 1 A See Enterprise Systems Connection A channel having an Enterprise Systems Connection channel to control unit I O interface that uses optical cables as a transmission medium Electrostatic Discharge Glossary 99 F fault symptom code FSC FC fiber optics fiber optic cable Fibre Channel fibre connection FICON FICON channel file protect firmware FRU FSC FTP G Gb Gbps gigabyte GB 100 19840 User s Reference Manual September 2008 A four character hexadecimal code generated in response to an error to help isolate failures within the device Some FSCs are for information purposes only See Fibre Channel The branch of optical technology concerned with the transmission of radiant power through fibers made of transparent materials such as glass fused silica and plastic E A cable made of ultrathin glass or silica fibers which can transmit data using pulses of laser light Fiber optic cables have several advantages over copper cables they have much less signal loss they allow information to be transmitted at higher speeds and over longer distances they are not affected by external electrical noise and they are better for transmissions which require security The National Comm
94. orded particularly by MVS systems at the beginning of the media 2 An alphanumeric label that the host software uses to identify a volume It attaches to the spine of a cartridge and is both human and machine readable A single pass of tape from either BOT to EOT or EOT to BOT with the heads in a fixed transverse location A setting on a data cartridge that allows data to be written on the tape An output operation that sends a processed record to an output device or output file IBM A setting on a data cartridge that prevents data from being written on the tape Reading data is still possible Revision YA 95739 Index Symbols asterisk message 80 A activity indicator 41 advertencia mensajes en el manual 14 agreement internal code 21 alert messages in manual 14 ASIA Diags message 80 B Bank n Bad message 80 Boot Fail message 80 BT Monitor message 80 build MIR 77 Build MIR command 64 button See switches 44 C cartridge care of 95 description 30 handling 95 indentify damage 95 manual unload device 41 media ID labels 30 mixed media management 31 read write compatibility 31 shipping 96 storing of 95 VolSafe 30 write protect 70 cartridge case cleaning 96 cartridge scratch loader description 27 caution description 14 shielded cables 19 CC Diags message 80 Chk xxxx message 80 95739 Revision YA clean indicator 41 clean the drive 73 cleaning cartridge overview 30 Cleaning message 80
95. p Unit Rack Mount Tray 054002 Up to six single drive and or dual drive trays may coexist in a single cabinet such as the stand alone CBNT42U rack The tray fits in a standard 483 mm 19 in rack with a depth of at least 780 mm 30 75 in Cartridge Scratch Loader Drive Units The cartridge scratch loader CSL configuration T9840A only features manual automatic system sequencing of up to six tape cartridges Both the CSL desktop and rack mountable units are shown in the following figure FIGURE 1 4 CSL Desktop and Rack mount T9840A CSL Desktop Unit T9840A CSL Rack Mount Tray T9840A C54003 The desktop version comprises a single drive power supply and loader mechanism contained in a cabinet with rubber feet The rack mountable version differs only in the cover and the addition of rail assembles for rack mounting A rack such as the CBNT42U can hold up to six CSLs or combinations of CSLs and manual load drive units 95739 Revision YA Chapter 1 Overview 27 Configurations Library Attached Configurations The drive is available in configurations for various libraries several are shown in the following figure Refer to the appropriate library documentation for additional information FIGURE 1 5 T9840 Tape Drive Library Attached Configurations Tray Assembly for 9310 9360 9740 L5510 Tray Assembly for 9710 T9840A B Tray Assembly for SL8500 Tray Assembly for Libraries L180 L700 L1400 C53886 28 19
96. quired to correct it An invalid MIR can be corrected in several ways using the drive model that created the cartridge for example a T9840A B formatted cartridge in a T9840A B drive or a T9840C formatted cartridge in a T9840C drive 1 Reading to the end of existing data EOD creates a complete and valid MIR This is done at normal read speeds and could take up to 45 minutes for a full 9840 tape cartridge 2 Appending to the tape cartridge will also create a valid MIR although a slow speed read must first be done to the end of existing user data 3 The Drive Operation Menu offline Rebuild MIR utility will sequentially read from block ID 0 to the EOD The MIR will be complete and valid when the tape cartridge is unloaded see Build MIR on page 77 4 The Drive Operation Menu offline Make Data Tape utility will reformat the tape cartridge with a valid MIR However all previous data will be lost see Reformat a Cartridge on page 76 The memory resident MIR is always rebuilt to the last block read on the fly during normal read write functions When the partially rebuilt memory resident MIR is written to the tape during the download process the invalid flag is reset because the MIR is now partially valid This can result in seemingly conflicting performance from a single tape 36 19840 User s Reference Manual September 2008 Revision YA 95739 Mixed Media Management Notes a If a tape cartridge with
97. r correspondence if they are available This expedites our response QS woe Y y Adobe PostScript Revision YA 95739 Revision History EC Date Revision Description 112188 October 1998 A Initial release 113499 February 1999 B See this edition for a description of changes 112275 April 1999 C See this edition for a description of changes 112388 September 1999 D See this edition for a description of changes 112350 November 1999 E See this edition for a description of changes 111457 March 2000 F See this edition for a description of changes 111488 May 2000 G See this edition for a description of changes 111523 August 2000 H See this edition for a description of changes 111542 August 2000 J See this edition for a description of changes 111643 May 2001 K See this edition for a description of changes 111692 November 2001 L See this edition for a description of changes 111768 November 2002 M See this edition for a description of changes 111823 March 2003 N See this edition for a description of changes 111841 May 2003 P See this edition for a description of changes 111850 July 2003 R See this edition for a description of changes 111864 September 2003 T See this edition for a description of changes 111872 September 2003 U See this edition for a description of changes 111895 May 2004 V See this edition for a description of changes 111407 May 2005 WwW See this edition for a description of changes EC000238 January 2008 Y See
98. r xy FF 00 13 2 character hexidecimal library address manufacturing setting is FF and it must be changed to a valid address when the drive is installed in a 9310 library CSL Xxxxxx Y N CSL operating mode System Auto Manual H xxxxxxxx first half 64 bit drive node world wide name L xxxxxxxx second half 64 bit drive node world wide name WWN Custom only when custom dynamic WWN is set S N xxxxxx drive serial number last six characters of drive DMOD Exit CFG exit view configuration Press Select to exit press Menu to return to the View CFG submenu 56 19840 User s Reference Manual September 2008 Revision YA e 95739 Online Menu Operation SCSI View Configuration Menu Tree Use the online view configuration menu tree as a brief guide Online Offline Press Select to toggle then press Menu to set View CFG View Configuration Press Select to enter press Menu to bypass 95739 Revision YA Cmprss xxx Yes Off No compression mode Full DSE x Y N data security erase mode SL Prot x Y N standard label protection mode SCSI ID x 0 7 or 0 F bus address of the drive for narrow or wide bus Tar Neg X Y N determines if the transmission speed is negotiable SCSI Xxxxx Ultra Slow Fast sets the drive transmission speed SCSI xxBit 16 8 selects the drive bus width Tape Bar x Y N tape completion indication English Espanol Francais Italiano Deutsch current language VolSafe X Y N
99. rent firmware level including the drive interface sub module level Interface level 4 06 or higher is required for proper SL8500 operation Drive Specific Displays When you select an individual drive in the tree pane the right pane changes to display drive specific data instead of the drive folder summary data You can view and use the SLC drive displays to develop reports to assist with the analysis of drive related problems In SLC 4 10 the Status Properties and Display tabs are available Note The drive displays are evolving New releases might contain an additional tab or expanded information elements Therefore what is presented here is for illustrative purposes only No attempt will be made to keep the examples current Status The tab shown in FIGURE 2 6 displays key drive status data Health State Device State Access State Drive State Drive needs cleaning and Host activity Note The list of states is variable based upon the drive library and SLC firmware FIGURE 2 6 SL8500 SLC Drive Status Tab Streamline Library Console Tools Help System Detail Apply Refresh Library 1 0 0 0 0 pDrive amp CAP Folder 1 0 0 0 Status Properties Display 9 Drive Folder 1 0 0 0 Drive 1 1 1 1 4 State 9 Drive 1 1 2 1 3 Transition Request select transition y Drive 1 2 1 1
100. s TABLE 5 2 Operator Panel Display Messages Continued Display Meaning Recommended Action enhndnsn The tape drive firmware level is Contact authorized service personnel Hardware insufficient to control the tape drive revision level supported by the firmware in this drive hardware CodCrFaill The tape drive cannot write code onto the data cartridge tape or the tape drive cannot position the data cartridge tape Ensure that the tape is write enabled or try another cartridge tape CodCrFail2 The tape drive cannot read code from the data cartridge tape Retry the operation or try another cartridge tape If the problem persists contact authorized service personnel CodeUpDate The firmware in the tape drive is being updated from the host the operator panel switches are locked None CodUpFaill The tape drive cannot read the data cartridge tape or the tape drive cannot position the data cartridge tape Try another cartridge tape CodU yo Tn o N The EEPROM failed Contact authorized service personnel CodUpFail3 EZ The tape drive cannot read code from the data cartridge tape Retry the operation or try another cartridge tape If the problem persists contact authorized service personnel CodUpFail4 The data cartridge tape is not a code update cartridge tape Try another code update cartridge tape If the problem persists conta
101. s View TCP Press Select to enter press Menu to bypass 95739 Revision YA DHCP x Y N must be set to N to view change the static settings IPhaaa IPlccc NMhaaa NMlccc GWhaaa GWliccc bbb IP Address high first half of static IP address ddd IP Address low second half of static IP address ddd Net Mask low second half of sub net mask bbb Gateway high first half of gateway address bbb Net Mask high first half of sub net mask ddd Gateway low second half of gateway address Exit TCP Press Select to exit press Menu to return to the View TCP submenu Chapter 3 Menus 61 Offline Menus Offline Menus With the offline menus the operator can change configuration settings reformat a data tape cartridge and build the media information region MIR on a tape cartridge FIGURE 3 2 Offline Menus Interface Menu Tree Change Drive Change Drive ChangeDrive Change Drive ChangeTCP 1P Drive View Drive View CSL Configuration Firmware Exit Menu Level Firmware Configuration Configuration Configuration Configuration Level Fibre Channel SCSI ESCON FICON Operations NA T9X40A l Compress Compress Compress Interface See Note IPL from Tape Drive View CSL Exits Menu Mode Mode Mode Selection Update MC lela dana i System DSE Mode DSE Mode DSE Mode Compress uona PA PortAandB SCSIID Logi
102. s Indicators TABLE 5 1 shows the meaning of the indicators located on the front panel and the recommended action TABLE 5 1 Operator Panel Indicators Indicators power activity clean service Meaning Recommended Action Off The drive is powered off Power on the drive as required Flashing Off The drive is in initial None program load IPL Persistent Off The drive failed IPL and Power the drive off and on Flashing cannot exit the sequence again If the problem persists contact authorized service personnel On Off Normal operation None On Off No tape cartridge is Load a tape cartridge as loaded needed On On A tape cartridge is loaded None On Flashing The tape is moving None On Off No cleaning is required None On On Cleaning is required Load the appropriate cleaning cartridge in the drive 95739 Revision YA 79 Messages TABLE 5 1 Operator Panel Indicators Continued Indicators power activity clean service Meaning Recommended Action On Flashing On Cleaning is proceeding None On On A drive error occurred Perform an IPL on the drive If the problem persists contact authorized service personnel On Flashing An error occurred and Observe the display message dump data was collected See TABLE 5 2 for more information about the message TABLE 5 2 lists operator panel display messages meanings and recommended acti
103. s selection of Online default or Offline menus m Press the Select switch to toggle between online mode and offline mode as desired then press the Menu switch to advance to the second menu item Note If you press the Menu switch again you will bypass the second menu item and advance to the third menu item View Change Configuration menus display drive configuration settings view only when online or allow drive configuration changes when offline Press Menu to advance the display to the next menu Press Select to enter the submenu View Change TCP Configuration menus display the drive Transmission Control Protocol Internet Protocol TCP IP configuration settings view only when online or allow TCP IP configuration changes when offline Press Menu to advance the display to the next menu Press Select to enter the submenu Drive Operations menus offline only provide drive utilities Press Menu to advance the display to the next menu Press Select to enter the submenu The Drive Firmware menu view only displays the current drive firmware release level The Exit Menu allows you the choice to either return to the Online Offline selection menu or to exit the menu system The last character in the Exit menu is a that signifies that you must make a choice Press Select to exit the menu or press Menu to repeat the main menu Note The Virtual Operator Panel application provides the capability to view the configurat
104. s 15 Index 107 Rewinding message 83 S Save Fails message 83 Saving Dump message 83 select switch 44 service indicator 41 shipping a cartridge 96 SL8500 drive tray LED 46 SLC folder 47 slot load unload 40 SrvoLdUnld command 64 Start Init message 83 status folder 48 store a data cartridge 95 structure of menus 51 Sun Web site 16 switches operator panel 44 T Taiwan warning statement 20 tape bar 42 tape drive interfaces 29 task operator build MIR 77 clean the drive 73 IPL the drive 69 load data cartridge 71 make a data cartridge 76 place the drive offline 75 place the drive online 74 power off the drive 68 power on the drive 68 unload data cartridge 72 view drive configuration 74 view firmware level 75 write protect a cartridge 70 translated messages 85 Trapped message 83 U unload a data cartridge 72 unload switch 44 Unloading message 83 UnWr xxxx message 83 user response to indicators 79 V vary the tape drive offline 75 vary the tape drive online 74 view drive configuration 74 firmware level 75 online main menu drive 53 entry point 53 exit 53 fibre channel drives 53 FICON drives 53 firmware 53 VolSafe cartridge 30 Ww W R Diag command 64 warning description of 14 WORM see VolSafe 30 Write Prot message 83 write protection cartridge 70 Writing message 83 Xx ox Dmp y message 81 108 19840 User s Reference Manual September 2008 Revision YA 95739 Sun Microsys
105. show the percentage of the total tape length that has been written and read Each dot represents 2 of the tape length each segment represents 10 Note The tape bar gets its information from the media information region MIR on the tape The MIR is written to the tape when the tape is unloaded If the MIR is bad the tape bar does not display To rewrite the MIR see Build MIR on page 77 Write Bar As data is written to tape the lighted dots forming the write bar appear at the left side of the display and advance to the right The write bar uses the full height of the display As the dots fill the display note that only every other dot is lighted The point where the write bar ends is the percentage of tape written Read Bar As data is read from the tape the read bar appears in the center of the write bar as a single row of unlighted dots This row is bordered above and below by single rows of lighted dots The read bar also begins at the left side of the display and advances to the right The point where the read bar ends is the percentage of tape that has been read FIGURE 2 2 on page 43 is a simplified and an actual view of a tape bar that shows a tape that is 50 written and 34 read 42 19840 User s Reference Manual September 2008 Revision YA 95739 FIGURE 2 2 Tape Bar Front Panel READ BAR 24 10 20 30 40 50 oc0eceo O00000 00000 c ece e0 0 e0 00 oe 0 0 0 0 009 0 000 ooooo 00000 00
106. supply reel in a protective housing A device that attaches to a tape drive to automatically load and unload tape cartridges into and out of the drive See cleaning cartridge A data cartridge that contains special material to clean the tape path in a transport or drive To save space by eliminating gaps empty fields redundancy or unnecessary data to shorten the length of records or files IBM One of a set of specified values that a data item can assume IBM The amount of time to prepare a tape cartridge for use in a T9840 Tape Drive The manner in which the hardware and software of an information processing system is organized and interconnected T An electrical or optical part that joins two or more other parts The number of errors that occur per a measurable amount of data on a tape The speed of a data transfer process usually expressed in bits per second or bytes per second IBM Revision YA 95739 Data Security Erase DSE data tape data tracks diagnostics drive dump dynamic host configuration protocol DHCP E emulation encryption enterprise Enterprise Systems Connection ESCON environmental requirement EOT error ESCON ESCON channel ESD 95739 Revision YA A random binary pattern over writing existing data from the point of an Erase command to the End of Tape point A data cartridge formatted for use as a regular data tape for the system in which
107. tems Inc 4150 Network Circle Santa Clara CA 95054 USA Phone 1 650 960 1300 or 1 800 555 9SUN Web sun com Go SUN S lo microsystems ARGENTINA 5411 4317 5636 AUSTRALIA 1 800 550 786 AUSTRIA 43 1 601 26 0 BALKANS 301 6188 111 BELGIUM 32 2 704 89 83 BRAZIL 55 11 51872100 BRUNEI 65 216 8333 CANADA 1 800 422 8020 GENERAL 416 964 2001 LEARNING MANAGEMENT SYSTEM SALES TORONTO CHILE 562 372 4500 COLOMBIA 571 629 2323 Czech REPUBLIC 420 2 33009311 DENMARK 45 4556 5040 e EGYPT 00 202 570 9442 FINLAND 358 9 525 561 e FRANCE 33 1 41 33 17 17 GERMANY 49 89 460 08 2788 GREECE 30 01 6188101 HONG KONG 852 2877 7077 HUNGARY 361 202 4415 INDIA 91 80 229 8989 INDONESIA 65 216 8333 IRELAND 353 1 668 4377 ISRAEL 972 9 9710500 ITALY 39 02 9259511 JAPAN 81 3 5779 1820 Korea 82 2 3453 6602 MALAYSIA 603 2116 1887 e MIDDLE East 00 9714 3366333 MEXICO 525 261 0344 NETHERLANDS 31 33 4515200 New ZEALAND 0800 786 338 e North West AFRICA 00 9714 3366333 Norway From Norway 47 22023950 To Norway 47 23369650 PAKISTAN 00 9714 3366333 PEOPLE s REPUBLIC OF CHINA 8610 6803 5588 PHILIPPINES 632 885 7867 POLAND 48 22 8747848 e PORTUGAL 351 21 413 4000 e RUSSIA 7 095 935 8411 SAUDI ARABIA 00 9714 3366333 SINGAPORE 65 216 8300 SOUTH AFRICA 27 11 256 6300 SPAIN 34 902 210 412 SRI LANKA 65 2168333 SWEDEN 46 8 631 22 00 SWITZERLAND 41 1 908 90 50 GERMAN 41 22
108. ter 5 Indicators and Messages 83 Messages Potential Operator Recovery Scenarios The following table contains Fault Symptom Codes FSCs that commonly result from an operator error The first column in the table lists an operator panel message at the time of the error event The description column provides insight into the error condition from which you should be able to determine a recovery action TABLE 5 3 Selected Check Message Meanings Message Description CHK 6109 This drive does not contain the key needed to decrypt this tape The ID of the missing key can be viewed from this drive using the VOP program The ID has also been written to the Operational Key Token OKT Connect the OKT to the Key Management Station KMS and view the error log for error 6109 CHK A33A The user requested a motion operation that requires a tape to be installed however a tape has not been loaded CHK A34C The user requested a write operation that requires a tape to be installed however a tape has not been loaded CHK A3FB A format override tape write operation failed The failure may not be serious Error recovery was not invoked for the failure Re attempting the test may resolve this issue CHK A733 The operator or library inserted a write protected tape into the drive while in a menu selected create tape mode If the write protect switch on the cartridge is moved to the unlocked position operation will work CHK A749 A high
109. the tape drive is not in use Checking for the following elements a There are no active jobs applications or programs using this drive b The operator panel activity indicator is steady and not flashing c The display window does not indicate any activity relative to tape movement such as reading writing or locating 2 Press the operator panel Unload switch An asterisk should appear in the display when the cartridge is unloaded Note If the drive is offline the asterisk will alternate with Offline 3 Grasp the cartridge by the finger grips and extract it from the load unload slot 4 Set the write protect switch to the locked position if applicable 72 T9840 User s Reference Manual September 2008 Revision YA 95739 Clean the Drive Clean the Drive After the tape drive transports a predetermined length of tape or records a pre determined number of errors the Clean indicator lights It is time to clean the tape drive Note Use the appropriate cleaning cartridge for the drive model see Cartridges on page 30 To clean the tape drive Caution Equipment damage Do not wet clean the tape drive Do not clean the tape drive unless the Clean indicator lights 1 Make sure the tape drive is not in use before proceeding to Step 2 Note If there is a tape loaded in the tape drive make sure the application or job that was using that tape drive is no longer running
110. til Exit XXX appears in the display window and press the Select switch to enter the main menu 2 Press the operator panel Select switch to toggle the drive state Online appears in the display window 3 Press the Menu switch until Exit Menu appears in the display window 4 Press the Select switch to exit the menu system 5 Bring the tape drive back online to the host This is accomplished by a Enterprise Vary the tape drive online for all host paths to the tape drive by keying in one of the following commands MVS V lt address gt online VM Vary on lt address gt Open Systems if there is a switch unit installed and the port to this tape drive was blocked unblock enable that switch port View Drive Configuration To view the current drive configuration settings 1 Press the operator panel Menu switch to enter the menu system a If Online appears in the tape drive s front panel go to Step 2 a If Offline appears in the tape drive s front panel shows press the Select switch to toggle the drive state Note It is important that you view configuration settings in the online state because you cannot accidently change online settings To change settings you must first set the drive to the offline state 2 Press the Menu switch until View CFG appears in the display window 74 T9840 User s Reference Manual September 2008 Revision YA 95739 Menu System Tasks 3 Press the operator panel Sel
111. to the operating environment for at least 24 hours Identify a Damaged Cartridge Caution Equipment damage Do not load a damaged cartridge Before loading a cartridge into a drive look for the following problems m Acracked or broken case m A dirty case see Cleaning on page 96 95739 Revision YA 95 A missing or broken access door A damaged file protect switch Liquid in the cartridge A loose label replace or remove the label Any other obvious damage Cleaning Wipe all dust dirt and moisture from the cartridge case with a lint free cloth Shipping Caution Data cartridge damage Ship data cartridges properly If you must ship tape cartridges especially if they are for remote system backup remote database duplication or disaster recovery follow these guidelines m Save the original factory packaging Use it or the equivalent to package tape cartridges m Wrap the tape cartridges in plastic to block moisture and contamination from entering the tape cartridges m Pad the tape cartridges on all sides m Fill voids in the packaging with padding equivalent to the original padding if you are using factory packaging to ship fewer tape cartridges than the packaging originally held or if you are using other packaging m Label the outside of the shipping carton clearly with text or accepted symbols that indicate Do not expose to magnetic fields Do not expose to moisture This end up
112. u document ne peut tre reproduite sous aucune forme par quelque moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bailleurs de licence s il y en a Le logiciel d tenu par des tiers et qui comprend la technologie relative aux polices de caracteres est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun Java StorageTek StorageTek logo L Series SL8500 PowderHorn VolSafe et Solaris sont des marques de fabrique ou des marques d pos es de Sun Microsystems Inc aux Etats Unis et dans d autres pays LA DOCUMENTATION EST FOURNIE EN L TAT ET TOUTES AUTRES CONDITIONS DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE A L APTITUDE A UNE UTILISATION PARTICULIERE OU A L ABSENCE DE CONTREFA ON We welcome your feedback Please contact the Sun Learning Solutions Feedback System at SLSFS Sun com or Sun Learning Services Sun Microsystems Inc 500 Eldorado Blvd 06 307 Broomfield CO 80021 USA Please include the publication name part number and edition number in you
113. uration gt Power Supply Folde World Wide Name Node 50 01 04 10 00 78 c2 40 Port A World Wide Name 50 01 04 10 00 78 c2 f1 Je j Fip Folder 1 0 0 0 0 pact EnaA E gt Robot Folder 1 0 0 Port A Loop ID ae o Y Safety Door Folder Port A Speed GB N A Port A Link status Uninitialized Port B World Wide Name 50 01 04 F0 00 78 c2 f2 Port B Enabled true Port A Loop ID auto Port B Speed GB N A Port B Link status Uninitialized 4 il 5 Comm Status UserID service Library 10 7 19 11 95739 Revision YA Chapter 2 Operator Controls 49 Library Controls Indicators Display The Display tab FIGURE 2 8 contains three sections Network Data Drive Virtual Op Panel and Drive LED Status FIGURE 2 8 SL8500 SLC Drive Display Tab Streamline Library Console Tools Help System Detail Apply Refresh Library 1 0 0 0 0 Drive amp Y car Folder 1 0 0 0 Status Properties Display 9 Drive Folder 1 0 0 0 Drive 1 1 2 1 3 Drive 1 2 1 1 2 Drive 1 3 2 1 2 Network Data Gateway Data Ip Address Ip Source Mac Address Subnet Mask Drive 1 3 2 1 1 Drive 1 4 1 1 1 a 9 Elevator Folder 1 0 es 7 Power Supply Folde Drive Virtual Op Panel amp Y Ftp Folder 1 0 0 0 0 Drive Display Data o Robot Folder 1 0 0 iV Safety Door Folder Drive Led Status Loaded Online Needs Clean Trace Available
114. ve loading slot Note For scratch data cartridges and other data cartridges on which the tape is written make sure the write protect switch on the data cartridge is in the unlocked position see Write protect Enable a Data Cartridge on page 70 4 Push the cartridge into the load slot Note For desktop or rack mounted tape drives when a cartridge is loaded the operator panel display window indicates one of the values in the following table Display Meaning Ready U The cartridge is ready and not file protected the drive can read write or append data Ready F The cartridge is ready and file protected or a VolSafe cartridge is loaded but the drive VolSafe option is disabled Ready A The VolSafe cartridge with the proper density is ready Ready H The data cartridge density is higher than the drive is capable of reading or writing Ready L The data cartridge is loaded into a drive that is capable of writing at a higher density the drive can read a lower density cartridge but cannot append data LOAD xxxx The cartridge load was not successful 95739 Revision YA Chapter 4 Operator Tasks 71 Unload a Data Cartridge Unload a Data Cartridge Caution Possible data corruption Do not push the Unload switch while a data cartridge is in use Doing so could cause the tape drive to stop writing and result in corrupted data on the tape To remove cartridges from the drive 1 Make sure
115. view 35 Mixed Media Management a Ifa T9840A B drive has down level drive firmware a high density data cartridge would be considered as a blank tape cartridge and a low density data cartridge would lose statistical data stored in the FIB during a previous mount into a T9840C drive Exceptional MIR Processing There are instances when the MIR process departs from the normal m Write Protect When the tape cartridge is write protected neither the MIR nor FIB is rewritten and statistical information for that mount is not captured If the tape cartridge is in a library that logically write protects the tape cartridge the MIR is updated as normal on each dismount m Major Error Power Off If a tape cartridge is mounted and the drive SNO s should not occur error or loses power the drive memory resident MIR is not written to the tape media Instead after IPL initial program load the drive will read the existing MIR on tape Special data is saved in EEPROM that will allow the existing MIR to be updated and rewritten to the media with the valid flag set Therefore the MIR will contain all positioning information up to the last mount and this tape will operate with mixed performance until EOD is found T9840A B C drives must have the appropriate drive firmware level to update the MIR after a SNO or power loss see Mixed Media Management on page 31 Invalid MIR Correction Once a tape cartridge has an invalid MIR some action is re
116. will stop when a tape cartridge is loaded 95739 Revision YA Chapter 4 Operator Tasks 69 Write protect Enable a Data Cartridge Write protect Enable a Data Cartridge To write protect or write enable a data cartridge move the write protect switch on the cartridge to the desired setting The write protect switch is located on the side of the cartridge as shown in FIGURE 4 1 The switch points to a padlock symbol on the case to indicate the following status Locked Write protected Data can only be read from the data cartridge Unlocked Write enabled unprotected Data can be read from and written to the standard data cartridge With a VolSafe cartridge data can be read from the cartridge and data can be appended if the drive VolSafe configuration option is enabled FIGURE 4 1 19840 Data Cartridge Write Protect Switch WRITE PROTECT MI SWITCH AR _ AS UNLOCKED LOCKED 053995 70 19840 User s Reference Manual September 2008 Revision YA 95739 Load a Data Cartridge Load a Data Cartridge To load a cartridge into a T9840 tape drive Note A T9840 tape drive accepts only T9840 cartridges 1 Inspect the cartridge for damage see Identify a Damaged Cartridge on page 95 2 Look into the drive load unload slot to make sure there are no obstructions 3 Hold the cartridge by the finger grips with the hub side down and insert the cartridge carefully into the tape dri

Download Pdf Manuals

Related Search

Related Contents

Omron Healthcare BP652 blood pressure unit  Guida informativa sui prodotti    Nokia DT-910  取扱説明書 (1.81 MB/PDF)    

Copyright © All rights reserved. Failed to retrieve file