PDF Manual - Walsh & Ford
Contents
1. DO NOT KINK FAILURE WILL RESULT IN TIGHTNESS IN THROTTLE CONTROL 3 17 MOTOR WILL BE COMMISSIONED AT FACTORY 3 1 8 BELT TENSION AND ALIGNMENT HAS BEEN FACTORY SET 3 1 9 ALL LIFTS BY CRANE UTILIZING THE INTERNAL LIFT LUGS IN UNIT TO PREVENT PAINT DAMAGE FORKLIFTS MAY BE USED HOWEVER THE BALANCE IS SET TO THE LEFT AS YOU FACE THE AUGER SEE INDICATOR ALSO THE AUGER MUST BE FOLDED TO TRANSPORT POSITION DISENGAGED AND NEVER ATTEMPT TO LIFT UNIT FROM OPPOSITE SIDE TO AUGER TOPPLE FACTOR WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 7 OF 24 COMBINATION BIN TRANSPORT KEY POINTS 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 TRANSPORT COMBINATION BIN A SAFETY COMES FIRST B KNOW YOUR STATE S TRANSPORT REQUIREMENTS C BE AWARE OF ELECTRICAL POLES AND LOW SLUNG WIRES D USE APPROPRIATE TRUCK WITH CORRECT LOAD RATING FOR TRANSPORT EMPTY AND FULL ENSURE AUGER DOORS ARE IN SHUT OFF POSITION AND AUGER IS FOLDED BACK INTO REST POSITION WITH CLAMP ENGAGED TELESCOPIC CHUTE IS TO BE SECURED BY HOOK PROVISION FOR BOLT DOWN TO DECK IS IN FEET FOR LEGS USE FLAT WASHER WITH HOLES TO LAYER IF TIMBER DECK ALSO USE NYLOC NUT IN ASSEMBLY ALSO USE CHAINS AND CHAIN BINDERS TO SECURE UNIT TO RAILS OF TRUCK THE NON AUGER SIDE SHOULD BE IN LINE WITH THE PASSENGER SIDE AND HARD UP AGAINST THE COMB RAIL MOVEMENT OVER CONTOUR BANKS GUTTERS SHOULD BE APPROACHED WITH CARE AND ON THE APPROPRIATE ANGLE WITH BIN FULL2. 20 OF 24 COMBINATION BINS JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET 10 JOB SAFETY AND ENVIRONMENTAL ANALYSIS JSEA WORKSHEET C Risk Assessment Likelihood that the accident will follow to completion A Almost certain Most likely and expected result if the selected complete sequence of events takes place 1 in 10 B Likely Quite possible not usual 1 in 10 to 100 chance C Moderate Would be unusual but possible sequence of events or coincidence 1 in 100 to 1 000 chance D Unlikely Would be a remotely possible coincidence 1 in 1 000 to 10 000 chance E Rare Never happened after many years exposure but is conceivably possible 1 in 10 000 to 100 000 Injury IlIness Damage Environmental Impact First aid minor damage contained spill Disabling injury damage up to 5 000 small uncontained spill Permanent disability injury damage 5 000 500 000 spill or release requiring notifying EPA Fatality damage 500 000 I million major spill or release with minor offsite impact Multiple fatalities damage lt 1 million major spill or release with major offsite impact WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 21 OF 24 COMBINATION BINS JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET 10 JOB SAFETY AND ENVIRONMENTAL ANALYSIS JSEA WORKSHEET To determine the risk choose the Likelihood and the Consequence Likelihood Consequence 3 Serious 4 Very Serious 5 Extreme A Almost certai
3. 3 DO NOT REACH IN UNDER UNIT WHILST IN OPERATION AT IDLE 2 14 DISABLE MOTOR IF UNIT IS NOT TO BE USED FOR AN EXTENDED PERIOD 2 15 ENSURE RISK ASSESSMENT IS COMPLETED PRIOR TO USE 2 16 USE P P E i e EAR PROTECTION WHILST USING THIS PRODUCT WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 6 OF 24 COMBINATION BIN ASSEMBLY 3 ASSEMBLY COMBINATION BIN KEY POINTS SAFETY COMES FIRST B THE AGENT OR DEALER IS RESPONSIBLE FOR COMMISSION ASSEMBLY C WALSH 8 FORD CAN ASSEMBLE AND COMMISSION IF REQUIRED COSTS WILL OCCUR 3 1 COMBINATION BIN 3 1 1 ALL UNITS ARE FACTORY RUN FOR DRIVE AND PERFORMANCE AND THEREFORE ARE FACTORY SET 3 1 2 DISCHARGE CHUTE IS STANDARD LENGTH AND CAN BE MODIFIED TO SUIT CLIENTS REQUIREMENTS BY CUTTING DOWN PULL CHUTE AND CHANGE CHAIN LENGTH AT THIS STAGE ENSURE YOUR SAFETY BY PERFORMING THIS ON A SECURE PLATFORM TO THE CORRECT HEIGHT 3 1 3 AUGER CLEAN OUT DOOR SHOULD BE LUBRICATED WITH LIGHT OIL DIESEL TO PREVENT FERTILIZER SWEAT OF STEEL IN SLIDE 3 1 4 AUGER HINGE POINT IS PRE LUBED AND WOULD REQUIRE GREASE SEASONALLY 3 1 5 DOOR ACTIVATION TO BIN CAN ONLY BE ACHIEVED WHEN THE AUGER IN IT S FIXED DELIVERY POSITION ONCE IN THIS POSITION IT S ADVISED SEASONALLY AND BEFORE FIRST LOAD IS PLACED IN UNIT THE DOORS ARE TO BE OPEN CLOSED TO ENSURE FREE MOVEMENT LUBRICATION WITH LIGHT OIL DIESEL IS STRONGLY ADVISED 3 1 6 TAKE EXCEPTIONAL CARE WITH THE CONTROL CABLE ALONG AUGER
4. AS YOUR NUMBER ONE PRIORITY IN THE USE OF ANY AGRICULTURAL PRODUCT WHETHER IT BE WALSH 8 FORD OR ANY OTHER SUPPLIER TAKE NOTE OF ANY RECOMMENDATIONS WE ADVISE IN THE SAFE USE OF ANY EQUIPMENT AND PLEASE INDUCT ANY WORKERS CONTRACTORS OF THEIR RESPONSIBILITY AND SAFETY IN THE USE OF THIS UNIT ENSURE THAT THEY SIGN OFF AS A MATTER OF RECORD IN THIS BOOKLET NOTE THIS DOCUMENT SHOULD BE USED INCONJUNCTION WITH MANUAL PHOTOS ON THE WEBSITE BE SAFE THINK SAFE AND CARE FOR YOUR WORKERS PETER WALSH SERIAL NUMBER OF UNIT THIS DOCUMENT HAS BEEN SENT TO YOU BY DELIVERY CONFIRMATION AUSTRALIA POST OR ATTACHED TO UNIT OR PROVIDED BY AGENT RESELLER WE REQUEST YOU ACKNOWLEDGE THIS BY RETURNING THE PRE PAID ENVELOPE WITH THE SIGNED ACKNOWLEDGMENT FORM ON LAST PAGE IN THIS DOCUMENT FAILURE TO DO SO WILL RESULT IN ALL LIABILITY ONUS UPON YOU AND NIL WARRANTY ON PRODUCT WE AIM TO CONFORM TO THE AUSTRALIAN STANDARDS AS NZS 1554 1 2004 STRUCTURAL STEEL WELDING AS 4024 1 1996 SAFEGUARDING OF MACHINERY AS 1121 1983 GUARDS FOR AGRICULTURAL PTO DRIVES AS 1755 2000 CONVEYORS SAFETY REQUIREMENTS WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 4 OF 24 COMBINATION BINS SIGN OFF FORM SIGN OFF FORM DATE EMPLOYEE EMPLOYEE NAME SIGNATURE EMPLOYEE SUPERVISOR SIGNATURE WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 5 OF 24 COMBINATION BINS SAFETY 2 SAFETY COMBINATION BINS KE
5. CENTRE OF GRAVITY OF TRUCK BIN COMBINATION VARIES FROM NORMAL SO APPROACHES TO DIFFICULT TERRAIN SHOULD BE APPROACHING WITH CARE AND IDEALLY WITH NO TILT TO THE AXIS OF TRUCK BE ALERT FOR OVERHEAD CABLES WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 8 OF 24 COMBINATION BINS SET UP UNIT FOR WORK 5 SET UP UNIT FOR WORK COMBINATION BINS KEY POINTS A SAFETY COMES FIRST B KNOW THE AREA AND CONDITIONS THAT YOU ARE GOING TO WORK WITH FOR HAZARDS C FORMULATE AND DOCUMENT JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET FOR UNIT S INTENDED USE 5 1 COMBINATION BINS OPERATIONAL CHECK 5 1 1 CLEAR AREA OF UNAUTHORIZED PEOPLE 5 1 2 SECURE UNIT TO TRAY OF TRUCK VIA CHAIN BINDERS BOLT DOWN 5 1 3 ENSURE WHEN LIFTING UNIT ALL PRECAUTIONS ARE TAKEN AS WELL AS APPROPRIATE LIFTING DEVICES ARE USED AND EQUIPMENT IS CAPABLE CERTIFIED FOR JOB USE INTERNAL LIFT LUGS 5 1 4 FUEL SERVICE ENGINE PRIOR TO COMMENCEMENT OF WORK 5 1 5 TRANSFER GRANULAR PRODUCTS TO APPROPRIATE BINS 5 1 6 MOVE UNIT TO SITE THAT S APPROPRIATE FOR DISCHARGE REQUIREMENTS WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 9 OF 24 COMBINATION BINS OPERATION 6 OPERATION KEY POINTS A SAFETY COMES FIRST B BE AWARE OF OPERATIONAL CHECK 6 1 COMBINATION BINS 6 11 ENSURE UNIT ON LEVEL GROUND 6 12 EXTEND OUT AUGER UNIT AND CLAMP HINGE THIS MAY REQUIRE THE OPERATOR TO UTILIZE SAFETY HARNESS FOR WORK ON THE TRUCK 6 13 E
6. NGAGE MOTOR TO RUN WARM UP FOR SHORT PERIOD OF TIME ENGAGE MOTOR TO RPM TO SUIT DELIVERY ENGAGE THROTTLE LEVER AT SPOUT END TO ENABLE CENTRIFICAL CLUTCH USE LEVERS AT AUGER TO OPEN AUGER DOOR FOR DELIVERY DISCHARGE IS VARIABLE TO DOOR OPENING AND MOTOR RPM 6 14 USE CHUTE TO DIRECT FLOW INTO COMBINE OR AIR SEEDER BIN 6 1 5 USE THROTTLE AT CHUTE TO BACK OFF DELIVERY BY USE OF CENTRIFICAL CLUTCH 6 1 6 CLOSE OFF DOOR BY LEVER HANDLE AND LET RESIDUAL PRODUCT IN AUGER RUN INTO APPROPRIATE RECEIVAL POINT 6 17 FOLD AUGER BACK AND CLAMP IN APPROPRIATE MANNER BY IT S RESTRAINTS 6 1 8 ENSURE ALWAYS DOORS ARE CLOSED OFF AND AUGER IS FOLDED BACK BEFORE MOVING OFF TO A NEW DISCHARGE SITE WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 10 OF 24 COMBINATION BINS HYDRAULICS 7 HYDRAULICS COMBINATION BINS NIL HYDRAULICS WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 11 OF 24 COMBINATION BINS MAINTENANCE KEY POINTS A B 8 MAINTENANCE AUTHORIZED PERSONNEL ONLY TO PERFORM MAINTENANCE ENSURE LOCK OUT PROCEDURES AREIN PLACE IF MAINTENANCE REQUIRES GUARDS TO BE REMOVED ENSURE THEY ARE REPLACED BACK ONTO MACHINE AT END OF SERVICE DO NOT ATTEMPT TO ENTER BIN WITHOUT BACK UP PERSONNEL AND MEANS BY WHICH TO REMOVE A PERSON ENSURE NOTIFICATION TO YOUR SUPERVISOR AS TO YOUR INTENSIONS TO ENTER UNIT UNIT IS TO BE IN A STAND ALONE SITUATION BEFORE ANY ATTEMPT TO SERVICE UNIT PLATFORM I E
7. NIT PLEASE SEND BACK DUPLICATE COPY TO WALSH amp FORD IN SUPPLIED ENVELOPE
8. OPERATIONS amp SAFETY MANUAL EFFECTIVE 1 SEPTEMBER 2013 VERSION IV WALSH amp FORD Established 1949 BULK HANDLING SPECIALISTS COMBINATION BINS REPLACES VERSION 2010 Version III PETER WALSH INVESTMENTS PTY LTD ABN 48144741748 FACTORY OFFICE 4 DAN STREET P O BOX 272 DALBY QUEENSLAND 4405 AUSTRALIA FACTORY PHONE NUMBERS 07 46626174 07 46626110 FACTORY FAX NUMBER 07 46622435 A HRS SALES MOBILE NUMBER 0412836938 WALSH amp FORD E MAIL ADDRESS admin walshandford com au WALSH amp FORD WEBSITE www walshandford com au N B OWNERS OPERATORS OF MODELS PRIOR TO SEPTEMBER 2013 ARE ADVISED TO UPDATE SAFETY REQUIREMENTS AS PER DESCRIPTION IN THIS DOCUMENT ADDITIONAL DETAILED PHOTOS ARE INCLUDED ON THE WEBSITE UNDER MANUALS IMAGES COMBINATION BINS WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 2 OF 24 COMBINATION BINS TABLE OF CONTENTS 10 11 TABLE OF CONTENTS INTRODUCTION SIGN OFF FORM SAFETY P P E ASSEMBLY TRANSPORT SET UP OF UNIT FOR WORK OPERATION MAINTENANCE AND STORAGE MAINTENANCE SHED WARRANTY JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET PARTS OWNER CONFIRMATION WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 3 OF 24 COMBINATION BINS INTRODUCTION 1 INTRODUCTION TO THE CUSTOMER IN THIS BRIEF INTRODUCTION TO YOUR NEW WALSH amp FORD PRODUCT WE WOULD LIKE TO ACKNOWLEDGE SAFETY
9. SH amp FORD Dealer Agency freight prepaid 4 On sale of the implement Equipment Dealer must disclose and supply details of Warranty in written form This warranty shall be void if any part or parts not manufactured or approved by WALSH amp FORD are used either in the maintaining or servicing of the implement equipment covered by this Warranty No Warranty whatsoever is given on modified altered or rebuilt machinery Any arbitrary modification alteration or rebuilding carried out on the implement equipment will relieve WALSH amp FORD of any liability whatsoever for and resulting loss damage or injury This Warranty is not applicable to engines electrical motors clutches universal joints tyres and tubes hydraulic motors hydraulic wheel drives and hydraulic hose rims or any other component parts not manufactured by WALSH amp FORD This Warranty does not extend to any consequential loss or damage however caused or arising including failure in operation or performance of goods sold or repaired or replacement work or service performed thereon or thereto or any loss incurred inter alia for hire or unauthorized labour supplies substituted machinery or rented machinery or for any loss or damage incurred because of delay in harvesting or removal of crops or grain or for any event resulting in loss of crops livestock or other losses nor shall WALSH amp FORD be liable for any injury or negligence howsoever caused This Warra
10. TRUCK IS TO BE DISABLED 8 1 COMBINATION BINS 8 1 0 DISABLE POWER SUPPLY AND LOCK OUT BEFORE ANY MAINTENANCE 8 1 1 CHECK V BELT FOR TENSION AND CONDITION REPLACE AT 2 YEAR INTERVALS 8 1 2 ENSURE DOOR HANDLE MOVES FREELY AND LUBE WITH LIGHT OIL AT SLIDES AT BOTTOM OF BIN 8 1 3 CHECK CONDITION OF BOTTOM BEARING LIFE SPAN IS PROPORTIONAL TO TONNAGE CYCLED THROUGH UNIT 8 1 4 MAINTAIN PETROL MOTOR AS PER MANUAL PROVIDED BY ITS MANUFACTURE 8 15 GREASE AUGER HINGE SEASONAL GREASE BOTTOM PILLOW BLOCK BEARING DAILY WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 12 OF 24 COMBINATION BINS MAINTENANCE MAINTENANCE SIGN OFF FORM 6 MONTHS 12 MONTHS 18 MONTHS 24 MONTHS 30 MONTHS 36 MONTHS 42 MONTHS 48 MONTHS 54 MONTHS 60 MONTHS 66 MONTHS 72 MONTHS 78 MONTHS 84 MONTHS 90 MONTHS 96 MONTHS 102 MONTHS 108 MONTHS 114 MONTHS 120 MONTHS 126 MONTHS 132 MONTHS 138 MONTHS 142 MONTHS 148 MONTHS WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 13 OF 24 COMBINATION BINS MAINTENANCE MAINTENANCE SIGN OFF FORM 160 MONTHS 166 MONTHS 172 MONTHS 184 MONTHS 190 MONTHS 178 MONTHS WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 14 OF 24 COMBINATION BINS WARRANTY 9 WARRANTY WALSH amp FORD as suppliers of agricultural implements equipment provides this warranty for implements equipment manufactured at Dalby Queensland Subject to such other conditions warranties
11. Y POINTS SAFETY COMES FIRST B SAFETY OF OTHERS IS IMPERATIVE C ITIS YOUR RESPONSIBILITY TO KNOW THE OPERATIONAL REQUIREMENTS OF THE UNIT AND TO ADVISE OTHERS IN YOUR CARE D IT WILL BE CONSIDERED AS MISUSE OF THE EQUIPMENT IF YOU THE OPERATOR ARE UNFAMILIAR WITH THE SAFETY OPERATION AND ITS ORIGINAL INTENTION OF USE 2 1 FAILURE TO READ THESE INSTRUCTIONS AND FAILURE ACKNOWLEDGE THEM IS CONSIDERED AS MISUSE OF THE PRODUCT 22 DO NOT OPERATE UNIT WITHOUT SAFETY GUARDS SHIELDS IN PLACE 2 3 DO NOT REMOVE ANY PROTECTIVE MEASURES FOR ANY REASON 2 4 KEEP PEOPLE WHO ARE NOT INDUCTED IN THE USE AND SAFETY MEASURES AWAY FROM THE UNIT AT ALL TIMES BY A MINIMUM PHYSICAL DISTANCE EQUAL TO THE SIZE OF THE MACHINE CHILDREN AT ALL TIMES ARE NOT ALLOWED IN THE VICINITY AS DESCRIBED ABOVE 2 5 ENSURE BODY LIMBS HANDS FEET CLOTHING ARE CLEAR OF DRIVE LINE AS WELL AS PULLEYS AND BELTS 2 6 KEEP WELL CLEAR OF OVERHEAD ELECTRICAL HAZARDS AND POLES 2 7 DO NOT MODIFY ANY PROTECTIVE MEASURES 2 8 DO NOT CLIMB UPON UNIT WHILST IN OPERATION 2 9 DO NOT CLIMB UPON BIN WHILST TRUCK IS RUNNING AND NEVER BE ON TRA Y OR ON IN BIN WHILST TRUCK IS IN TRANSIT 2 10 UTILIZE SAFETY HARNESS WHILST WORKING ON TRAY AND AROUND BIN 2 11 KEEP CLEAR OF BIN TRUCK BY A MINIMUM PHYSICAL DISTANCE EQUAL TO THE SIZE OF THE COMBINATION WHILST THE UNIT IS MOVED OR OPERATED 2 12 DO NOT CLEAN ADJUST LUBRICATE THE UNIT WHILST OPERATING OR MOVING 2 1
12. and or undertakings which may apply from time to time under the laws of Australia and or any applicable State or Territory thereof WALSH amp FORD warrants with respect to each new item of agricultural implement equipment that for a period of twelve months on agricultural implements equipment from the date of the original retail sale thereof WALSH amp FORD will repair or replace free of charge any part of such agricultural implements equipment found to be defective in factory materials of workmanship under normal use and operation within Australia PROVIDED THAT 1 The agricultural implement equipment as the case may be has been properly a set up and operated strictly in accordance with the recommendations set forth in the Owner s and or Service Manual provided with the implement equipment b Used and operated strictly within the capacity and operation limitations specified by WALSH amp FORD and c Properly maintained and cared for d Used solely for the purpose for which it was designed in customary agricultural operations intended use Use in any other way is considered contrary to intended use e All regulations rules practices on safety and or occupational medicine and or road traffic Acts and Regulations are observed at all times and 2 The repair and replacement is carried out by an authorized WALSH amp FORD Dealer Agency and 3 The defective part is returned at the request of the authorized WAL
13. e authorized WALSH FORD Dealer through whom the equipment was purchased the selling Dealer has primary responsibility for performing WALSH amp FORD Warranty repairs and replacements under the WALSH amp FORD Warranty 3 What should I do to obtain WALSH amp FORD Warranty service Contact the selling Dealer or if that is inconvenient any authorized WALSH amp FORD Dealer explain the problem you have encountered and arrange with the Dealer a mutually convenient time for the warranty repairs or replacement to be effected Alternatively contact may be made direct to Factory Headquarters at 4 Dan Street Dalby Queensland P O Box 272 Telephone 07 46626174 Facsimile 07 466 22435 Email admin walshandford com au WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 16 OF 24 COMBINATION BINS JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET 10 JOB SAFETY AND ENVIRONMENTAL ANALYSIS JSEA WORKSHEET Unit Site Date Name s of employee s completing this JSEA Tick Type of permit required Confined Space Excavation 1 Hot Work Fall Risk Control Other Special PPE Requirements WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 17 OF 24 COMBINATION BINS JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET 10 JOB SAFETY AND ENVIRONMENTAL ANALYSIS JSEA WORKSHEET Special Tools or Equipment Required consider such things as gas detection ventilation fans lighting scaff
14. n Extreme Extreme B Likely Extreme Extreme C Moderate Extreme Extreme Your assessment Before controls Likelihood Consequence Risk Score After controls Likelihood Consequence Risk Score WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 22 OF 24 COMBINATION BINS JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET 10 JOB SAFETY AND ENVIRONMENTAL ANALYSIS JSEA WORKSHEET D Approvals Extreme Immediate action activity Manager Risk discontinued until risk is Safety and minimised Training Co ordinator High Risk Immediate action activity Manager discontinued until risk is Safety and minimised Training Co ordinator G Moderate Risk addressed as part of Site Manager Risk risk control program G Low Risk Risk identified to Supervisor employees WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 23 OF 24 COMBINATION BINS PARTS 11 PARTS FOR PARTS PLEASE CONTACT WALSH amp FORD WITH UNIT S SERIAL NUMBER WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 24 OF 24 COMBINATION BINS OWNER CONFIRMATION 12 OWNER CONFIRMATION ARES ACKNOWLEDGE BY PURCHASE OF THIS WAESH FORD UNIT THAT I HAVE AND WILL ACCEPT INSTRUCTIONS OF ITS INTENDED USE AND WILL ALSO TRAIN AND INDUCT EMPLOYEES AND SUBCONTRACTORS IN THE MACHINE USE PLEASE ENCLOSE A MUD MAP OF DIRECTIONS FROM YOUR NEAREST TOWN INCLUDING DISTANCES AND ROAD NAMES SIGNED DATE SERIAL NUMBER OF U
15. nty does not exclude and necessarily applicable condition or warranty implied by the Trade Practices Act1974 or any such condition or warranty implied by the applicable State Laws Subject thereto no warranty guarantee or representation as to WALSH amp FORD implements equipment other than as contained herein is made or given by WALSH amp FORD WALSH amp FORD accepts no liability whatsoever for damage loss or injury howsoever resulting from misuse or non compliance with and strict adherence to the operating instructions and safety manual WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 15 OF 24 COMBINATION BINS WARRANTY CONT 9 WARRANTY cont The following are the answers to the most frequently asked questions about the WALSH 4 FORD Warranty provided with agricultural implements equipment purchased through your authorized WALSH amp FORD Dealer Distributor 1 When does WALSH FORD Warranty period commence If the equipment was purchased as new equipment the WALSH amp FORD Warranty period will commence on the date the equipment was purchased new at retail If the equipment has been purchased as used equipment the WALSH amp FORD Warranty commencement date is the date on which the equipment was first purchased new at retail 2 Who performs WALSH FORD Warranty repairs or replacements While any other authorized WALSH amp FORD Dealer may carry out WALSH amp FORD Warranty repairs or replacements th
16. olding etc Potential Environmental Hazards Air pollution dust fumes Spills to ground Dirty Water discharge Hazard flora fauna Noise pollution off site 1 Spills to water Other Hazardous Materials to be used attach MSDS pe Fire Emergency Requirements WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 18 OF 24 COMBINATION BINS JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET 10 JOB SAFETY AND ENVIRONMENTAL ANALYSIS JSEA WORKSHEET Other Potential Hazards to consider G Electrical G Occupational Noise G Work at Height G Other workers G Gas dust fumes G Chemical Access amp egress G Pressure air water gas G Manual Handling G Heat G Radiation G Light illumination G Other Special Training Requirements Prescribed Occupation Certification Requirement WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE 19 OF 24 COMBINATION BINS JOB SAFETY AND ENVIRONMENTAL ANALYSIS WORKSHEET 10 JOB SAFETY AND ENVIRONMENTAL ANALYSIS JSEA WORKSHEET Job Safety and Environmental Analysis JSEA Worksheet JSEA Number B Job steps list the major steps required to Potential Hazard Required Hazard Control Person Responsible a the task Additional comments or details of special precautions to be taken WALSH amp FORD OPERATIONS amp SAFETY MANUAL PAGE
Download Pdf Manuals
Related Search