700 lbs High Lift Telescopic Transmission Jack
Contents
1. on top of the upright post 2 and secure with M10x25 bolts and washers 8 amp 9 4 Attach saddle assembly 10 above the ram of hydraulic unit 7 using pin and spring pin 11 amp 12 5 Attach all four bracket supports 13 onto the saddle plate with bolts and wing nuts 14 amp 15 6 Attach saddle brackets 16 to bracket support 13 with provided nuts 17 7 Finally attach chains 18 with bolts and nuts 19 amp 20 N A oS Ov Figure 2 Assembly Reference for Model BH7000 SAFETY INSTRUCTIONS BEFORE USE 1 Verify that the product and the application are compatible if in doubt call Blackhawk Automotive Technical Service 816 891 6390 2 Read the operator s manual completely and familiarize yourself thoroughly with the product and the hazards associ ated with its improper use before using this product 3 With ram fully retracted remove oil filler plug This will help release any pressurized air which may be trapped within the reservoir 3 Check for and tighten any loose assemblies Ensure that casters move freely Read and understand all printed material provided with and on this product before use e Do not exceed rated capacity e Use only on hard level surfaces capable of supporting rated capacity loads e Use of this jack is limited to the removal installation and transportation of transmissions transfer cases and transaxles e Do not use a transmission jack to tilt or su2. N Pomona Ave Kansas City MO 64153 U S A Tel 816 891 6390 Fax 816 891 6599 E Mail sales blackhawk automotive com BH7000 Replacement parts mem Pari Description J oy a lso On Filer Pug o 2 BLeA10000000 Hydraulic ni 7 3 BL80 20000 000 Pump Hande 7 4_____ 250 01000 000_ BaseHa o o s 250 90037 001 Caster Assy a 6 BL80 16002 000 Release Vave Levr 1 Cid z 250 90037 0083 Bont Assy gt e M2000000 MmSoew 2 9_ L100 05000 000___ Ghain Asy 2 mo T250 04000 000 Saade Bracket 4 m 250 08000 000___ Saddle Assy i t 2509000901 Hardware Kit all bois amp nuts S E e moomo Mawa oo BR PO PO Po AYP N sp SS T TORIES lt SS Figure 3 Replacement Parts Illustration for Model BH7000 7 Fw ts A OF
3. AME n A ZT OF Blackhawk Hutomo tive Blackhawk Automotive is a Licensed Trac lark Made by SFA Companies Kansas City MO 700 Ibs High Lift Telescopic Transmission Jack Operating Instructions amp Parts Manual BH7000 SFA Companies 2005 10939 N Pomona Ave Kansas City MO 64153 816 891 6390 sales blackhawk automotive com Before using this product read this manual and follow all its Safety Rules and Operating Instructions Made in PRC ONE YEAR LIMITED WARRANTY For a period of one 1 year from date of purchase SFA Companies will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclusive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to SFA Companies Warranty Service Department 10939 N Pomona Ave Kansas City MO 64153 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 SFA COMPANIES SHALL NOT BE LIABLE FORANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHAT SOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO ONE YEAR OTHERWIS
4. E THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT CCOVERED BY THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SFA Companies 2005 10939 N Pomona Ave Kansas City MO 64153 816 891 6390 sales blackhawk automotive com SAVE THESE INSTRUCTIONS For your safety read understand and follow the information provided with and on this jack The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use The owner and operator shall be aware that use and repair of this product may require special skills and knowledge Instructions and safety information shall be conveyed in the operator s native language before use of this jack is authorized If any doubt exists as to the safe and proper use of this jack remove from service immediately Inspect before each use Do not use if the
5. is centered on the saddle and load is stable before moving jack Lower saddle Caution Be sure all tools and personnel are clear before lowering load Dynamic shock loads are created by quickly opening and closing the release valve as the load is being lowered The resulting of overload may cause hydraulic system failure Slowly gently turn release valve counterclockwise to lower saddle MAINTENANCE Important Use only a good grade hydraulic jack oil Avoid mixing different types of fluid and NEVER use brake fluid turbine oil transmission fluid motor oil or glycerin Improper fluid can cause premature failure of the jack and the poten tial for sudden and immediate loss of load We recommend Hein Werner HW93291 or equivalent Adding oil 1 With saddle fully lowered set jack in its upright level position Remove oil filler plug 2 Fill until oil is level with the filler hole reinstall oil filler plug Changing oil For best performance and longest life replace the complete fluid supply at least once per year 1 With saddle fully lowered set jack in its upright level position Remove the oil filler plug 2 Lay the jack on its side and drain the fluid into a suitable container Note Dispose of hydraulic fluid in accordance with local regulations 3 Set jack in its level upright position 4 Fill with oil until level with the filler hole reinstall oil filler plug Lubrication A periodic coating of light lubricating oi
6. l to pivot points axles and hinges will help to prevent rust and assure that casters and pump assemblies move freely Cleaning Periodically check the ram for signs of rust or corrosion Clean as needed and wipe with an oily cloth Note Never use sand paper or abrasive material on these surfaces Storage When not in use store the jack with saddle in lowest position TROUBLESHOOTING Symptom Possible Causes Corrective Action e Release valve not tightly closed e Ensure release valve tightly closed SACR MIO Vode e Overload condition e Remedy overload condition e Release valve not tightly closed e Ensure release valve tightly closed Jack bleeds off after lift e Overload condition e Remedy overload condition e Hydraulic unit malfunction e Contact Blackhawk Tech Service Jack will not lower after unloading e Reservoir overftilled e Drain fluid to proper level e Fluid level low e Ensure proper fluid level Poor lift performance e Air trapped in system e With ram fully retracted remove oil filler plug to let pressurized air escape then reinstall oil filler plug Will not lift to full extension e Fluid level low e Ensure proper fluid level REPLACEMENT PARTS Not all components of the jack are replacement items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts give Model number parts number and description Call or write for current pricing SFA Companies 10939
7. pport a vehicle Ensure the center of gravity is centered on the saddle e For your safety do not exceed 10 degree tilt angle of the saddle assembly in all directions e Adequately support the vehicle before starting repairs e Use the chain provided e If loaded jack must be moved make certain that the load is secured by appropriate means is stable is in lowest position is moved over smooth hard surfaces and that the lifting platform is level Do not allow any part of your body under the load while jack is supporting a load e Use only the saddle assembly to lift Never use any other part of the jack as a lifting surface e No alterations shall be made to this product e Only attachmens and or adapters supplied by the manufacturer shall be used e This is a lifting and lowering device only Transfer load immediately to appropriate support device for service or repair e Failure to heed these markings may result in personal injury and or property damage OPERATION Raise saddle 1 Turn release valve clockwise until firm Pump handle until load is contacted To avoid crushing and related 2 Follow vehicle manufacturers recommended injuries procedures for removing the load as outlined in vehicle NEVER work on under or service manual or repair guide around a load supported only by a jack Immediately transfer the load to an appropriate work station 3 Secure load with provided chains Ensure load s center of gravity
8. re are broken bent cracked or damaged parts including labels Any jack that appears damaged in any way or operates abnormally shall be removed from service immediately If the jack has been or suspected to have been subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue to use until jack has been inspected by a Blackhawk Automotive authorized service center It is recom mended that an annual inspection be done by qualified personnel Labels and Operator s Manual are available from manufacturer PRODUCT DESCRIPTION Blackhawk Automotive High Lift Telescopic Transmission Jack is designed to be used as an aid in the removal and installation of automotive and light truck transmissions transfer cases and transaxles It is intended for use under an overhead lift or in a garage pit SPECIFICATIONS Hydraulic Lifting Min Height Max Height BH7000 700 Lbs 36 1 8 x 32 5 8 19 1 8 57 1 4 76 3 8 Saddle Bracket Saddle ETS De CRS csi Tilt Adjustment Knobs Hydraulic Unit Handle Sleeve Figure 1 BH7000 Components 3 ASSEMBLY Refer to Figure 1 amp 2 1 Attach the base halves 1 to the upright post 2 then secure using bolt rods washers and M12 nuts 3 4 amp 5 provided 2 Attach all four casters 6 to the base halves 1 using the washers and M12 nuts 4 amp 5 provided 3 Place hydraulic unit 7
Download Pdf Manuals
Related Search