Home
Service Manual - Appliance Factory Parts
Contents
1. Filter system this is the introduction of only the filter part Filter name Function Cleaning and replacement frequency Nano silver Nano silver antibacterial This filter enables 2 roles of antibacterial process and removal antibacterial Pre filter of large dust particles with only one filter to extent the washing Clean frequency of about 1 month Big gust removal miter frequency of the washable filter Nano silver antibacterial The washable HEPA filter removes the minute dust particles HEPA filter Washable HEPA filter including dead ticks flower powder cigarette smoke particle Clean frequency of about 6 months minute dust minute particle floating fungus animal fur etc Deodorizer filter Antibacterial mesh This removes the smell of animal fur NO4 bathroom smell Clean frequency of about 6 months G Washable deodorizer filter alkali amp acid smell volatile oil compound VOCs Copyright 2007 LG Electronics Inc All right reserved 10 LGE Internal Use Only Only for training and service purposes 4 Operations Functions Manual Operation Mode Bf Air Purifying Operation puiyindoorair MM Press Operation Mode Button e Turns the unit on and off Press once to turn on again to turn off e A confirmation tone will sound to indicate that the unit is powering on or turning off The unit will also produce a tone when the unit is first plugged in What is Start up Operation When
2. e Do not place the power cord or unit near a heater radiator or any other heat source e This unit is not designed for use by children Children should be supervised to ensure that they do not play with or climb on the unit e Do not use your unit to remove hair spray and insecticides from a room These chemicals not only clog the filters but could damage the unit e Secure the unit to prevent it from rolling on smooth floors When moving the unit insure that the power cord is unplugged from the wall e Do not move the unit by pulling or pushing on the front panel e Do not use the top of the unit for storage Keep liquids away from the top of the unit e Other than cleaning and replacing the filters there are no user replaceable components in your unit Serve of this should be referred to a qualified service technician e Do not apply pressure to the front panel of the unit e Keep hands and objects away from the air inlet and outlet e Do not clean the unit by submerging in water Water in the unit will damage the insulation and create an electrical shock hazard If water enters the unit unplug immediately and contact Customer Service Copyright O 2007 LG Electronics Inc All right reserved 4 LGE Internal Use Only Only for training and service purposes When Installation o When using the unit maintain a distance of at least 3 feet between the unit and any television or audio product e Avoid installing the unit in d
3. Do not use the unit near water sources that could allow moisture to enter the unit Overheating and or water infiltration could lead to a fire or a shock hazard and could result in failure to the product LGE Internal Use Only 3 Copyright 2007 LG Electronics Inc All right reserved Only for training and service purposes 1 Safety instructions Operation o e Make sure the power cord is plugged firmly and completely into the outlet e Do not operate with wet hands e If the power cord ever becomes frayed or damaged do not attempt to repair The cord should be replaced by a qualified technician e Never pull the power plug away from the outlet by pulling on the wire Always grasp the cord by the receptacle end e Do not install a place where there are much industrial Oil dust or metallic dust It may cause fire and failure of product e When the power code is damaged it should be repaired by the qualified person to prevent any risk Otherwise it may cause electric shock fire or failure of product e Never pour or allow water to run onto or into the unit It could damage internal components and create a shock and fire hazard e Keep objects such as curtains away from the air opening in the unit The openings must be free from obstruction for the unit to work efficiently e Do not run power cords under carpeting or other coverings which could fray the cord and expose the wires Frayed cords are a shock and fire hazard
4. absolutely necessary Do not disassemble any part that is not on the disassemble instruction i Major components Disassemble Remove the Door Assembly 1 Open the door Assemble 2 Loosen the screw 1 position 3 Push the Hook Remove the door assembly by pulling up LGE Internal Use Only 15 Copyright 2007 LG Electronics Inc All right reserved Only for training and service purposes Major components Disassemble Assemble and Repair instruction Remove the Body Assembly 1 Please remove 6 screws from the Back Case using a Screw Driver 2 Separate the Front Case from Body Assembly Remove the Connector 3 Replace remove the necessary parts Key PCB Micro Switch Bracket Bracket Gas Sensor Copyright 2007 LG Electronics Inc All right reserved 16 Only for training and service purposes Key PCB Rope Micro Switch LGE Internal Use Only 4 Removing a Main PCB Switch Assembly on Harness Separate Control Cover from the Rear Case Remove 1 Screw Screw Remove Switch Assembly Remove 2 Screw Screw AY Waki Switch Assembly Motor Wir
5. by plugging or unplugging the power cord Always turn off and unplug the unit when it will not be used for extended periods of time This conserves energy and reduces the chance of accidents e Clean filters on a regular basis Improper filter maintenance can cause premature failure of the product Warn the user to unplug or disconnect the appliance from the power supply before servicing e A damaged filter can create an electrical hazard e If a humidifier is used in the same room as your unit keep the humidifier a safe distance away from the humidifier could clog the filters and create an electrical shock hazard e Do not use your unit to remove food odors while cooking Airborne oils that are released during cooking will clog the filters Wait until cooking is completed before operating your unit Do not open the front panel during the operation of the product Opening the front panel stops the operation e After washing your filters make sure they are completely dry before reinserting them into the unit Do not run your unit with wet filters e Keep flammable products away from your unit Failure to keep flammable products away from your unit could lead to premature failure or create a fire hazard Copyright O 2007 LG Electronics Inc All right reserved 6 LGE Internal Use Only Only for training and service purposes 2 Logics Terminology 1 VOCs Volatile organic compounds 1 What is VOCs Carcinogenic substance
6. Inhale system side surface inhale system Purifying system Three dimension filter system Major Filter System Nano silver Pre Filter Washable HEPA Filter Washable Deodorization Filter Filter composition Washable part Sensor Display Digital 1 Sensor smell Easy Picto display Display Information Purity level Operation Mode Operation Mode Automatic Turbo Sleep Wind Speed Turbo Strong Weak Copyright O 2007 LG Electronics Inc All right reserved Only for training and service purposes 8 LGE Internal Use Only 4 Operations Functions Manual Spare part Name Mainframe Pre filter A i Power plug Front panel Deodorizer sensor Operation Mode Button Display and Control Panel indicator AUTO TURBO SLEEP is Operation Mode Button NE Clean Air Indicator Light This is the button to change The indicator light will show the quality of the the operating mode air in the surrounding area Operation mode A white indicator light indicates clean air and a low fan speed A red indicator light indicates a poor air quality and will run the fan on a high speed LGE Internal Use Only 9 Copyright 2007 LG Electronics Inc All right reserved Only for training and service purposes 4 Operations Functions Manual Pre filter HEPA filter G Deodorizer filter
7. Only for training and service purposes Troubleshooting and inspection direction LED Display Malfunction Are Main PCB ASM and Power PCB ASM CONNECTOR correctly connected e Check CN DSP connection Is voltage on both C12 terminals of Main PCB ASM 12V e Replace Main PCB ASM YES Replace Main PCB ASM i Cleanness lamp Display blinking Are Main PCB ASM and Gas Sensor CONNECTOR correctly connected e Check CN GAS connection Is the voltage of CN GAS PIN 1 3 CN DUST PIN 5V e Replace Main PCB ASM Replace Gas Sensor ASM Copyright 2007 LG Electronics Inc All right reserved 20 LGE Internal Use Only Only for training and service purposes Troubleshooting and inspection direction i Fan Malfunction Is the voltage of Main PCB CN MOTOR PIN 1 4 310V e Replace Main PCB ASM Is the POWER PCB ASM CN MOTOR CONNECTOR plugged in properly e Check CN MOTOR connection Check after power off Replace MOTOR LGE Internal Use Only 21 Copyright 2007 LG Electronics Inc All right reserved Only for training and service purposes PCB Circuit Diagram Parts Layouts a COMPONENT SIDE RO4 co BEY Copyright O 2007 LG Electronics Inc All right reserved 22 LGE In
8. Website http biz lgservice com LG AIR PURIFIER MODEL PS S200CW PS S200RP CAUTION BEFORE SERVICING THE UNIT READ THE SAFETY PRECAUTIONS IN THIS MANUAL February 2008 P NO MFL37942805 Printed in Korea SECTION 1 PAGE 3 6 SECTION 4 PAGE 9 14 SECTION 5 PAGE 15 17 SECTION 6 PAGE 18 SECTION 7 PAGE 19 21 SECTION 8 PAGE 22 23 SECTION 9 PAGE 24 26 Safety instructions Logics Major Specifications of each Model Operations Functions Manual Main Components Disassemble Assemble and Repair Instruction Electric diagram Troubleshooting and inspection direction PCB Circuit Diagram Parts Layout Exploded View Svc Components inventory Copyright 2007 LG Electronics Inc All right reserved 2 Only for training and service purposes O a mi a a UY LGE Internal Use Only 1 Safety instructions For your safety the information in this manual must be followed to minimize the risk of fire or explosion electric shock or to prevent property damage personal injury or death AN This symbol will alert you to any product detail or operation that could lead to a safety hazard if the instructions in the manual are not followed properly NM Warning If not followed it can cause death or major injury to the user NM Caution This symbol will alert you to the possibility of improper use that may result in damage Read instruct
9. e Main Wire 5 Removing a Fan Remove Nut using a wrench Turn it counter clockwise 6 Removing a Motor Please remove 3 screws from the Motor Cover Remove the motor cover Take out Motor 7 Assemble them in the reverse order of the disassembly LGE Internal Use Only 17 Copyright 2007 LG Electronics Inc All right reserved Only for training and service purposes 6 Electric diagram FAN MOTOR POWER CORD Fan MOTOR CN MOTOR CN POWER Main PCB ASSY CN GAS CN DOOR GAS DOOR CN DSP SENSOR SWITCH Display Copyright 2007 LG Electronics Inc All right reserved 18 LGE Internal Use Only Only for training and service purposes Troubleshooting and inspection direction Please take a look at the panel arrangement and the circuit drawing i Complete Malfunction s input AC voltage being supplied to both Main PCB ASM C01 terminals NO e Make sure that power line is plugged in e Check the fuse in Main PCB ASM FUSE YES Is DC voltage on both Main NO PCB ASM C12 terminals 12V Replace Main PCB AM YES Is DC voltage on both NO C24 terminals of Main e Replace Main PCB ASM PCB ASM 5V YES Does the Reset alarm occur NO when the power is turned on Replace Main PCB ASM YES Check LED Display soldering LGE Internal Use Only 19 Copyright O 2007 LG Electronics Inc All right reserved
10. f AUTO gt TURBO gt SLEEP gt STOP repeatedly auto TURBO super e The cleanness lamp will be turned off after 3 seconds of sleep operation Copyright 2007 LG Electronics Inc All right reserved 12 LGE Internal Use Only Only for training and service purposes 4 Operations Functions Manual Filter Cleaning e The prefilter should be cleaned on a monthly basis Turn unit off and unplug before cleaning Open the front panel Remove the filter from the mainframe by pulling the handle near the center of the filter Align latches into the groves to reinstall Pull the HEPA filter and deodorizer filter to the front to separate from the main unit Clean the Pre filter with a vacuum cleaner or a soft brush Clean the filter every a month Clean the Pre filter with a vacuum cleaner or a soft brush and when the contamination is severe use a neutral detergent and water to clean it off To clean both the HEPA filter and the Deodorizing filter soak the filter in warm water with a mild detergent for 1 hour Remove particles from the filter by shaking the water from the filter Rinse the filter with warm water Let air dry before placing filters back in the unit Filter type Cleaning frequency Pre filter Clean frequency of about 1 month Washable HEPA filter Clean frequency of about 6 months Washable deodorizer filter Clean frequency of about 6 months e For your safety turn off and u
11. first turned on the unit will go through a Start up function which prepares the unit for operation During this two minutes period the display will fluctuate to indicate that the unit is sensing the air quality in the room MM Select Auto Mode by pressing the Operation Mode button e The Operation Mode button will switch from one setting to the SUP next by repeatedly pressing the Operation Mode button OA Y Nx AUTO gt TURBO gt SLEEP gt STOP auto TURBO SLEEP e A white indicator light indicates clean air and a low fan speed A red indicator light indicates a poor air quality and will run the fan on a high speed e The fan level will automatically adjust to the air quality of the room How to clean the odor sensor e To clean the odor sensor use a soft brush or vacuum cleaner every 6 months e Do not allow dirt to fall back into the unit LGE Internal Use Only 11 Copyright 2007 LG Electronics Inc All right reserved Only for training and service purposes 4 Operations Functions Manual I Select Turbo Mode by pressing the Operation Mode button S When you press the Operation Mode button it will switch in O A L the order of AUTO gt TURBO gt SLEEP gt STOP AUTO Suliso SLEEP repeatedly Select Sleep Mode by pressing the Operation Mode button NAL e When you press the Operation Mode button it will switch in amp the order o
12. ight 2007 LG Electronics Inc All right reserved Only for training and service purposes LG Electronics Inc
13. ions to avoid damage or injury This appliance has a polarized plug one blade is wider than the other To reduce the risk of electric shock this plug is intended to fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician Do not attempt to defeat this safety feature When Installation o e If the power cord becomes worn or damaged the cord should only be replaced by a qualified service technician using genuine replacement parts e Do not plug other appliances into the same outlet Overloading of any outlet can cause a fire or create an electrical shock hazard e Do not remove the round grounding plug prong from the plug e Do not operate this or any electrical appliance when you smell gas e Do not operate with wet hands or in a damp environment e Do not disassemble or modify the air purifier or the power cord e Do not use this or any appliance near flammable gases or liquids liquids or other combustibles such as gasoline benzene thinner etc e If you hear abnormal sounds or smell smoke immediately unplug your unit and the unit checked by a qualified service technician Make sure the unit and cord are positioned where it does not create a tipping hazard Do not roll heavy furniture over the top of the cord e Do not use near open flames e Keep this product out of the direct ray of the sun or other heat sources
14. irect sunlight and never operate the unit near or around open flames or other heat sources e Never use your unit to remove toxic gasses such as Carbon Monoxide Natural or Liquefied Petroleum Gasses e Do not use your unit to remove food odors while cooking Airborne oils that are released during cooking will clog the filters Wait until cooking is complete before operating your unit e Install the unit on a stable flat surface e Maintain a minimum distance of 5 feet from any heat producing light source For proper ventilation maintain a distance of 6 inches or more from a wall e Do not use except AC 120V Otherwise it may cause fire or electrical shock e This unit is not designed to remove combustion by products such as those produced by open flame burners Toxic substances such as carbon monoxide should be ventilated from the room by either using an exhaust fan or by opening a window e Your unit is not designed to be used in moving vehicles such as cars RV s or boats LGE Internal Use Only 5 Copyright 2007 LG Electronics Inc All right reserved Only for training and service purposes Operation o To prevent damage to plants or injury to pets make sure they are not exposed to direct air flow from the unit This unit is not intended to be used for the preservation of art objects or precision machinery e Clean with a soft cloth and mild detergent Filter should be cleaned monthly e Do not start or stop operation
15. nplug the air purifier before cleaning A e Allow the filters to completely dry before using A Caution Utilizing the unit before all the filters are completely dry may result in the odors from the unit e Replace filters when unable to remove all dirt on the filter e Do not rub filters with your hands J LGE Internal Use Only 13 Copyright 2007 LG Electronics Inc All right reserved Only for training and service purposes 4 Operations Functions Manual Exterior clean and storage method Wipe the exterior of the unit with a soft cloth using warm water and a mild detergent e Do not use harsh cleaners or very hot water Do not wash in the A dishwasher A Caution Never pour water onto the unit it could damage the internal components and create a shock and fire hazard Operate the air cleaner for more than 1 hour on a clear day and then press the Operation Mode button to stop the operation Turn unit off and unplug power cord Clean and protect the unit s mainframe Cover the unit while storing for an extended period of time Copyright 2007 LG Electronics Inc All right reserved 14 LGE Internal Use Only Only for training and service purposes i Please read this before you disassemble Please unplug the power before disassemble 1 Most components are connected with bolts or mounted on the other parts Please disassemble according to the instruction 2 Please do not disassemble unless it is
16. s that cause allergies or respiratory ailments such as a paint adhesives spray construction materials wax carpet and etc Unlike the general perception that only cheap construction materials emit VOCs high quality new constructions may also emit VOCs It may stay remained in a closet or inside of furniture even after several years LGE Internal Use Only Filters Introduction 1 Nano silver Pre Filter One filter performs antibiotic treatment anti mold treatment and dust removal providing a purified air 2 Washable HEPA Filter HEPA filter polluted by acarid deadbody pollen small dust and float mildew animal bodyhair etc can be washed 3 Washable Deodorization Filter This filter was processed with activation treatment for stronger adsorption function characteristic of charcoal This deodorization filter has higher level of negative ion minerals far infrared lays generation ability than charcoal Copyright 2007 LG Electronics Inc All right reserved Only for training and service purposes 3 Major specifications on each model Model name PS S200CW PS S200RP Measurement W x H x D 372mm X 463mm X 199mm Application Space 20m Weight 7 2Kg Power Supply 120 V ac 60 Hz Color Creamy White Romantic Pink Design Easy design for convenient operation Power usage 18W Turbo Noise Turbo 43dB Wind speed CMM Turbo 2 82CMM
17. ternal Use Only Only for training and service purposes 8 PCB Circuit Diagram Parts Layouts i DC PART Circuit Diagram 1 Col Pron IRon Ton nas ds E or amon w ee aero E m ur E A El le Ju a la le 2 ls aa i wa ea a aa a a a ove Sa EE pp 005 poor PPA Feel KA Q S Copyright 2007 LG Electronics Inc All right reserved 23 LGE Internal Use Only Only for training and service purposes EV Exploded View Svc Components inventory Exploded View MODEL PS S200CW PS S200RP oH ono LGE Internal Use Only Copyr
Download Pdf Manuals
Related Search
Related Contents
VITOTRONIC 100 Montage− und Serviceanleitung MASTERVISION BH-2065 User manual(PDF Format) AllerAir AirCarbon Cab Protector User's Manual User Guide ASReml User Guide - VSN International テプ卜ム800S 取扱説明書 Copyright © All rights reserved.
Failed to retrieve file