installation. This manual
Contents
1. Instruction Manual Machine P N 1000830 amp 1000831 1 INFORMATION oh 3 1 MOJU OMen 3 5 Electrical Installation 4 6 Plumbing Installation 22 2 4 7 4 9 DeScaling 10 Operating the SP9 Head For The First Time 11 Operating the SP9 Boiler For The First Time 12 Dispense Volume 0 5 13 Boiler Modes Of Operation 25 na R 6 142 Setup ModE 6 15 User SeUUp 6 16 Service User Set Up Options 17 Display Information Descriptions 2 CUTTING TEMPLATE 9 Du INSTALLATION 10 22 5 12 5 CALIBRATION2. 13 GO BREWING 14 16 INFORMATION Introduction The information provided in this manual is intended to assist in the installation and maintenance of the SP9 Head amp SP9 Boiler Please read the instructions carefully to prevent accidents and ensure an efficient installation This manual is not a substitute for any safety instructions or technical data affixed to the machine or its packaging All information in this manual is current at the time of publication and is subject to change without notice The company accepts no responsibility for any damage or injury caused by incorrect or unreasonable installation and operation Safety When using electrical appliances basic safety precautions should always be followed to prevent the risk of fire electric shock burns or other injuries or damages Read all operating and safety instructions carefully This appliance must be placed installed on a horizontal flat stable surface ambient temperatures this appliance should operate within are 5 C 35 C This appliance may be placed in self service areas if attended to by trained personnel Risk of flooding the hose supplied with the boiler is non toxic food quality tested to 190psi However hose is not a permanent connection It is therefore advisable to switch off boiler and close the stopcock valve when boiler is not in use e g overnight etc
3. Head SP9 Head is powered only through the connection of the head to the boiler with the electrical con nection provided e DO NOT turn on the boiler or engage the brew switch until head and boiler are plumbed together G ust 337347 NSF ANSI 4 INFORMATION Contact Marco Beverage Systems Limited 63d Heather Road Sandyford Industrial Estate Dublin 18 Tel 353 0 1 295 2674 email sales marco ie www marcobeveragesystems com Electrical Installation Procedure When installing the machine always observe the local regulations and standards The appliance is supplied with a moulded power cord A suitable mains power supply socket should be available within easy access of the appliance so that it can be disconnected easily after install Plumbing Installation Procedure Ensure that the equipment is installed according to local plumbing amp water regulations Mains water pressure required limits 14 5 145psi 100 1000kPa 0 1 1MPa Fit a stop valve on a cold water line and attach a 3 4 BSP male fitting E g 3 4 x 1 2 311 or washing machine type stop valve The SP9 Head has a drip tray attached with a drain outlet which should be plumbed to waste Maintenance This machine has been designed to give many years of trouble free service The only regular maintenance required is occasional de scaling Descaling Procedure Isolate machine from power supply Isolate machine from water supply
4. ALLOW TO COOL COMPLETELY Drain water from machine Remove all lids Remove as much scale as possible by hand paying particular attention to level probes White plastic with steel tab Be very careful not to damage any attachments Use ScaleKleen Marco part No 8000270 or similar Follow instructions carefully Thoroughly clean and flush the machine before re use Follow installation and first time operation instructions Run the brew cycle a minimum of two times using only water to fully flush the de scale solution through the SP9 Head Operating the SP9 Head for the first time The SP9 Head is connected to the SP9 Boiler by silicone hoses and a flying lead The SP9 Head s silicone hoses should be connected to the SP9 5 hose adapters and secured with the supplied hose clips connections on both machines are marked A amp connect A to A and to The SP9 Boiler vent should be connected to a hose adaptor marked vent on a SP9 Head The SP9 Boiler ideally should be positioned directly below the SP9 Head installed position Please refer to installation diagrams on pages 10 and 11 of this booklet Once the SP9 Head installation procedure has been carried out calibrate the SP9 Head The calibration should only be conducted by a trained service engineer see guideline on the following page INFORMATION Operating the SP9 Boiler for the first tim
5. and probes All actions cancelled CUTTING TEMPLATE NOT TO SCALE The above drawing illustrates where to position the counter cut outs if two SP9 Heads are being installed For a 1 1 scale cutting template please see the back page of this manual Option 1 Using an 80mm hole saw drill two holes as per the drawing Option 2 Use a jig saw or similar cutting device to cut out the full obround shape 080 INSTALLATION gt 100mm gt 700mm 4 Underside of SP9 Boiler Mains Water Input INSTALLATION 5 Attaching SP9 Head to the counter standard counter 6 Attaching SP9 Head to the counter thin counter thickness thickness 25 40mm lt 25mm The 2 standard braces can accommodate counter thicknesses up to 40mm Where the counter thickness is less than 25mm the hard plastic legs on the front brace must be removed and reattached to the other side of the brace using a screwdriver The rubber inserts in the brace should be removed and repositioned in the plastic legs as shown above 7 SP9 Head amp Boiler Connections HEAD ONE HEAD TWO POWER VENT FEED TO HEAD RETURN FEED BOILER Basket Holder Display Screen Power Ready Status Indicator Set Button Drip Tray DIAGRAM OF PARTS Head Boiler Head Box Contains SP9 Head amp mounting brackets Hos
6. utmost care has been taken in the manufacture and testing of this machine Failure to install maintain and or operate this machine according to the manufacturer s instructions may result in conditions that can cause injury or damage to property If in any doubt about the serviceability of the machine always contact the manufacturer or your own supplier for advice This machine is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or in struction concerning use of the machine by a person responsible for their safety Children should be supervised to ensure that they do not play with the machine In the event any wires are damaged such wires can only be replaced by experts or professional after service staff from the manufacturer after service department or similar function departments e CAUTION Risk of fire and electric shock Only to be used with manufacturer s specified power cord set Marco p n 1501487 USA 1501488 EU 1501489 UK lre This appliance should not be installed an area where a water jet could be used to clean it Access to the service area of the appliance is restricted to persons having knowledge and practical expe rience of the appliance and the relevant safety and hygiene requirements Warning Notes Boiler SP9 Boiler MUST be connected to a SP9 Head before use
7. e Check that all installation procedures have been carried out Ensure the water valve is on Plug in the SP9 Boiler to an appropriate electrical supply and press the power button on the front of the machine light will glow green and the machine will fill to a safe level above the elements before heating Ready Status light will cycle two red flashes while the machine is filling to the safe level After this amount of water has heated to the set point the machine will draw more water in until the temperature drops by 1 or 2 degrees The machine will then heat again This heat fill cycle continues until the SP9 Boiler is full e Whilst the machine is above the safe level and filling the Ready Status light will remain blank Ready Status light will glow green when the machine is both full and up to normal operating temperature Ensure the 5 9 Boiler is set to SP9 mode for use with the SP9 Head 5 9 Boiler takes 15 minutes to heat up initially 5 9 Boiler is now ready for use NOTE Because the machine is electronically controlled no priming is necessary Dispense Volume Calibration 1 Once all installation procedures are carried out the SP9 Head is ready to be calibrated 2 Turn the quantity dial to maximum value 3 Turn time dial to between 2 3 minutes 4 Place a large container gt 1 litre of known weight under the spray head 5 Initiate brew by togg
8. etting it to 0000 disables the pin default Default value 0000 SERV PIN 0000 PIN entry screen once PIN is set and user wants to access SER VICE SETUP this screen will pop up use top button to move through positions and bottom to scroll through the values 0 to 9 and again 0 if PIN is accepted you will gain access to the SERVICE SETUP if PIN is rejected machine will reset itself SAVE AND EXIT Press the Set button to save all the values and reset the machine INFORMATION Display Information Descriptions Status Description Boiler Off Machine off Display backlight off but temperature read out still working Fillin Water level below low level probe Machine is filling automatically Status LED 2 red blinks Fill the Tank Water level below low level probe Machine has to be refilled manually shown only in MANUAL mode Status LED 2 red blinks Wait Water is being heated Dispense valve disabled Boiler Ready Water is up to the temperature and can be used Note that this only means that the tank is heated and not that it is full Status LED green Dispense Water is being dispensed If machine is set to time dispenses there will also be a progress bar drawn underneath Dispense can always be cancelled by clicking the dispense button again Cooling Machine was set by the user to a lower temperature than the current tank temperature and is trying to cool down by taking in more c
9. ing Spray Head 4 hole factory fitted Spray Head 7 hole e Instruction Manual Wh Boiler Box Contains 5 9 Boiler Power Cord Vent Hosing Instruction Manual Water Inlet Hose Note Alternate spray head not suitable for cup by cup swapping Preferred sprayhead should be selected at install prior to calibration Toggle switch Quantity 100s Gram Time minutes 1 Turn quantity to maximum value amp time to between 2 3 2 Dispense note not using continuous dispense mode minutes 3 Weigh output BREWING 1 Select quantity 2 Select time 3 Place device with coffee under the spray head 4 Press toggle once BREWING 5 For continuious dispense double click 6 To cancel click mid brew anytime 7 Beeps 3 times once finished 1 1 CUTTING TEMPLATE 83 1mm SCALE 1 1
10. ling switch 6 Weigh amp record brew output 7 The output should be 750g or 10g 8 If output is within 10g of 750g further calibration is not necessary 9 If not to enter calibration mode hold down the toggle switch for a minimum of 3 sec 10 Along beep will emit to confirm that the machine is in calibration mode 11 Enter the mass recorded via the brew switch using the following example 0 If 724g was measured The toggle switch is used to input each digit successively To enter 7 the toggle switch is toggled 7 times o A long beep will emit To enter the 2 toggle the toggle switch 2 times o A long beep will emit To enter the 4 toggle the toggle switch 4 times To enter a 0 value simply do not toggle the toggle switch If calibration is successful a long beep will emit at the end of the process if not multiple short beeps will emit 12 Verify calibration by repeating steps 2 5 INFORMATION Boiler Modes of Operation Ensure the boiler is set to SP9 Mode for use with the SP9 Head Live read out of the tank temperature Current machine status Setup Mode To enter setup mode press power and set buttons on the front panel at the same time display will show USER SETUP message Release the buttons now to enter the user setup mode To enter advanced settings keep the buttons pressed until the display shows SERVICE SETUP mes sage and the
11. n release them both setup modes use front panel buttons to navigate the settings Power button to scroll through the functions Set button to increase set value press and hold for auto repeat User Setup Options The default temperature in the tank is 95 The user can set the temperature of the tank Use the naviga tion instructions above to change the temperature NOTE Temperature should never be set for more than 96 C because it may cause steam to be generated during low pressure days Service Setup Options Sets and shows remaining weeks before de scaling is needed 0 5 CALE TANK message on the screen Setting it to OFF will disable the DESCALE OFF function Range 1 60 weeks Default value OFF 777 Sets and shows remaining litres of water before filter change is needed CHANGE FILTER message on the screen Setting it to OFF will disable the function Range 100 9900 litres Default value OFF This is a factory setting and should only be changed by trained personnel This is a factory setting and should only be changed by trained personnel INFORMATION Sets the mode the machine works in SP9 mode must be selected for MODE SP9 _____ use with the SP9 Head Sets temperature units on screen Default value This sets max limit of the temperature that user can set in USER SETUP max value is 96 C SERV PIN limits access to SERVICE SETUP s
12. old water This process may take between 20 seconds to a few minutes depending on tank size and temperature difference Works only in COOL FILL mode Dispense water to cool the tank Machine cannot take more cold water to cool the tank because it is full Water needs to be dispensed to allow room for more cold water to come in and finish cooling process Descale Tank Descale timer elapsed Time to descale the tank Change Filter Litres output exceeds set value Time to change the water filter Check Low Probe Thermistor S C Low water level probe broken disconnected Machine detects high level probe signal but cannot detect low level one Filling is disabled Status LED 1 red flash Temperature sensor thermistor is short circuited Dispense and heater disabled Status LED 3 red flashes Element Failure Heating element is broken Error is triggered when after 20 minutes of heating and not taking in water temperature in the tank fails to increase Dispense is disabled Status LED 4 flashes Thermistor O C Temperature sensor thermistor is disconnected Dispense and heater disabled Status LED 5 red flashes Low Pressure Incoming water pressure too low The error will be reset after water supply restores All boiler functions are active Status LED 6 flashes Comm Error Display board lost communication with boiler PCB cannot receive serial data about temperature
Download Pdf Manuals
Related Search